Quadra-Fire TREKKERI-MBKTREKKERI-CSBTREKKERI-PMH User manual

1September 27, 20187082-153D
TREKKER INSERT PELLET
APPLIANCE
MODEL(S):
TREKKERI-MBK
TREKKERI-CSB
TREKKERI-PMH
Installation Manual
Installation & Appliance Set-Up
INSTALLER: Leave this manual with party responsible for use and operation.
OWNER: Retain this manual for future reference.
NOTICE: DO NOT DISCARD THIS MANUAL
Installation and service of this appliance should be performed by
qualified personnel. Hearth & Home Technologies recommends
HHT Factory Trained or NFI certified professionals.
Tested and approved for wood pellets only. Burning of
any other type of fuel voids your warranty.
CAUTION
CAUTION
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, re o󰀩cials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
WARNING
If the information in these instructions is
not followed exactly, a re could result
causing property damage, personal
injury, or death.
• Do not store or use gasoline or other ammable
vapors and liquids in the vicinity of this or any other
appliance.
• Do not over re - If appliance or chimney connector
glows, you are over ring. Over ring will void your
warranty.
• Comply with all minimum clearances to combustibles
as specied. Failure to comply may cause house re.
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down. Hot glass will
cause burns.
WARNING
• Do not touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
replace.
• Alert children and adults to hazards of high
temperatures
• High temperatures may ignite clothing or other
ammable materials.
• Keep clothing, furniture, draperies and other
ammable materials away.
NOTE
To obtain a French translation of this manual, please contact
your dealer or visit www.quadrare.com
Pour obtenir une traduction française de ce manuel, s’il vous
plaît contacter votre revendeur ou visitez www.quadrare.com

2September 27, 20187082-153D
TREKKER INSERT
1 Important Safety Information............. 3
A. Appliance Certication........................3
B. BTU & E󰀩ciency Specication .................3
C. Glass Specications .........................4
D. Electrical Rating ............................4
E. Mobile Home Approved .......................4
F. Non-Combustible Materials ....................4
G. Combustible Materials .......................4
H. Sleeping Room .............................4
I. California - Prop65 ...........................4
2 Getting Started .................................... 5
A. Design, Installation & Location Considerations .....5
B. Tools And Supplies Needed ...................6
C. Inspect Appliance and Components .............6
D. Install Checklist .............................7
3 Dimensions and Clearances.............. 8
A. Appliance Dimensions ........................8
B. Clearance to Combustibles, US & CAN ..........9
C. Minimum Opening for Masonry & ZC Fireplaces ..10
D. Hearth Extension...........................10
E. Floor Protection ............................10
F. Installation into a Factory-Built Fireplace .........11
G. Installation into a Masonry Fireplace ...........12
H. Prefabricated Metal Chimney .................12
4 Vent Information................................ 13
A. Venting Termination Minimum Requirements .....13
B. Avoiding Smoke and Odors...................14
C. Negative Pressure..........................15
D. Draft ....................................15
E. Chimney and Exhaust Connection .............15
F. Equivalent Feet of Pipe ......................16
G. Pipe Selection Chart .......................16
5 Venting Systems ............................... 17
A. Full Reline wit Outside Air - Horizontal ..........17
B. Full Reline with Outside Air - Vertical ...........18
6 Appliance Set-Up .............................. 19
A. Leveling System ...........................19
B. Outside Air Kit Instructions ...................19
C. Hearth Support ............................19
D. Removal of Cast Sides ......................20
E. Surround & Cast Trim Set ....................20
F. Surround & Basic Trim Set....................21
G. Optional Log Set Instructions .................21
H. Installation of Bluetooth Key ..................22
I. Power to Appliance and User Interface ..........22
J. Location & Mounting of User Interface...........22
7 Mobile Home Installation.................. 23
8 Reference Materials.......................... 24
A. Service & Maintenance Log ..................24
B. Accessory List .............................27
TABLE OF CONTENTS
Safety Alert Key:
• DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury.
• WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury.
• CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
• NOTICE: Indicates practices which may cause damage to the appliance or to property.
Quadra-Fire is a registered trademark of Hearth & Home Technologies.

3September 27, 2018 7082-153D
TREKKER INSERT
A. Appliance Certication B. BTU & E󰀩ciency Specication
1 Important Safety Information
Model Trekker Insert Pellet Appliance
Laboratory OMNI Test Laboratories, Inc.
Report No. 061-S-84-2
Type Solid Fuel Room Appliance, Pellet Fuel
Burning Type
Standard ASTM E1509-12, ULC-S628-93 and
(UM) 84-HUD, Mobile Home Approved.
FCC
Complies with Part 15 of FCC Rules.
Operation is subject to the following two
conditions: (1) this device may not cause
harmful interference, and (2) this device
must accept any interference received,
including interference that may cause
undesired operation.
This pellet appliance needs periodic inspection and repair for proper operation. It is against federal regulations to operate
this pellet appliance in a manner inconsistent with the operating instructions in the owner’s manual.
Approved for ZC reboxes.
Emissions Report
Number: 0061PS094E
EPA Certication #: 98-17
EPA Certied Emissions: 0.74 g/hr
*LHV Tested E󰀩ciency: 83.2%
**HHV Tested E󰀩ciency: 77.9%
***EPA BTU Output: 12,682 - 39,428 / HR
****BTU Input: 16,396 - 50,775 / HR
Vent Size: 3, 4 or 6 inches, “L” or “PL”
Hopper Capacity: 52 lbs.
Fuel Wood Pellets
* Weighted average LHV e󰀩ciency using data collected
during EPA emissions test.
**Weighted average HHV e󰀩ciency using data collected
during EPA emissions test.
***A range of BTU outputs based on HHV and the burn
rates from the low and high EPA tests.
****Maximum BTU input based on the high burn section
of the EPA emissions test.
NOTICE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM
E1509-12, ULC S628-93, (UM) 84-HUD and ULC/ORD-C-1482.
This manual describes the installation of the Quadra-Fire, Trekker Insert pellet appliance. This appliance meets the 2020
U.S. Environmental Protection Agency’s crib wood emission limits for wood heaters sold after May 15, 2020. Under
specic test conditions this heater has been shown to deliver heat at rates ranging from 12,682 to 39,428 Btu/hr.

4September 27, 20187082-153D
TREKKER INSERT
C. Glass Specications
This appliance is equipped with 5mm ceramic glass.
Replace glass only with 5mm ceramic glass. Please
contact your dealer for replacement glass.
D. Electrical Rating
115 VAC, 60 Hz, Start 2.9 Amps, Run 2.45 Amps
E. Mobile Home Approved
• This appliance is approved for mobile home
installations when not installed in a sleeping room and
when an outside combustion air inlet is provided.
• The structural integrity of the mobile home oor, ceiling,
and walls must be maintained.
• The appliance must be properly grounded to the frame
of the mobile home and use only Listed pellet vent
Class “L” or “PL” connector pipe.
• Outside Air Kit, part OAK-3 must be installed in a
mobile home installation.
H. Sleeping Room
When installed in a sleeping room it is recommended that
3ft of vertical be installed prior to horizontally exiting the
room and a smoke/CO alarm be installed in the bedroom.
The size of the room must be at least 50ft³ per 1,000 Btu/hr
stove input, if the stove exceeds the room size, out air must
be installed.
I. California - Prop65
WARNING
This product and the fuels used to operate this product (wood), and
the products of combustion of such fuels, can expose you to
chemicals including carbon black, which is known to the State of
California to cause cancer, and carbon monoxide, which is known to
the State of California to cause birth defects or other reproductive
harm. For more information go to: WWW.P65Warnings.ca.gov
G. Combustible Materials
Material made of/or surfaced with any of the following
materials:
- Wood
- Compressed Paper
- Plant Fibers
- Plastic
- Plywood/OSB
- Sheet Rock (drywall)
Any material that can ignite and burn: ame proofed or not,
plastered or non-plastered.
Improper installation, adjustment, alteration, service or
maintenance can cause injury or property damage.
For assistance or additional information, consult a qualied
installer, service agency or your dealer.
NOTE: Hearth & Home Technologies, manufacturer
of this appliance, reserves the right to alter its
products, their specications and/or price without
notice.
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth &
Home Technologies.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Operating appliance without legs attached (if
supplied with appliance).
• Do NOT Over re - If appliance or chimney connector
glows, you are over ring.
Any such action that may cause a re hazard.
WARNING
Fire Risk
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be voided
by, the following actions:
F. Non-Combustible Materials
Material which will not ignite and burn, composed of any
combination of the following:
-Steel
- Plaster
-Brick
-Iron
-Concrete
-Tile
-Glass
-Slate
Materials reported as passing ASTM E 136, Standard Test
Method for Behavior of Metals, in a Vertical Tube Furnace
of 750° C.

5September 27, 2018 7082-153D
TREKKER INSERT
A. Design, Installation & Location
Considerations
Install Guide
2 Getting Started
Marginal Location:
• Below peak
Location NOT recommended:
• Not the highest point of the roof
• Wind loading possible
Multi-level Roofs
Windward
Leeward
Recommended:
Outside Air Intake
on windward side
NOT recommended:
Outside Air Intake
on leeward side
Recommended Location:
• Above peak
Recommended:
• Insulated exterior chase
in cooler climates
Recommended Location:
• Above peak
• Inside heated space
Location NOT recommended:
• Too close to tree
• Below adjacent structure
• Lower roof line
• Avoid outside wall
Marginal Location:
• Wind loading possible
Figure 5.1
1. Appliance Location
Since pellet exhaust can contain ash, soot or sparks, you
must consider the location of:
• Windows
• Air Intakes
• Air Conditioner
• Overhang, so󰀩ts, porch roofs, adjacent walls
• Landscaping, vegetation
• Horizontal or vertical vent termination
2. Floor Support
The supporting oor under the appliance must be able to
handle the weight of the appliance, fuel load and the weight
of the chimney.
Ensure that your oor will support these weights prior to
installation. Add su󰀩cient additional support to meet this
weight requirement prior to installation. The weight of the
appliance is 510 lbs. with a full load of fuel the max weight
is 557 lbs.
NOTICE: Check building codes prior to installation.
• Installation MUST comply with local, regional, state and
national codes and regulations.
• Consult insurance carrier, local building inspector,
re o󰀩cials or authorities having jurisdiction over
restrictions, installation inspection and permits.
It is a good idea to plan your installation on paper, using
exact measurements for clearances and oor protection,
before actually beginning the installation. Location of the
appliance and chimney will a󰀨ect performance.
Consideration must be given to:
• Safety, convenience, tra󰀩c ow
• Placement of the chimney and chimney connector and
to minimize the use of chimney o󰀨sets.
• Place the appliance where there will be a clear
passage for a Listed chimney through the ceiling and
roof (vertical) or through exterior wall (horizontal).
• Installing the required outside air kit will a󰀨ect the
location of the vent termination.
When locating vent and venting termination, the ideal
location is to vent above roof line when possible. This
minimizes the a󰀨ects of wind loading.
WARNING
Risk of Fire.
Damaged parts could impair safe operation. Do NOT
install damaged, incomplete or substitute components.

6September 27, 20187082-153D
TREKKER INSERT
NOTE: Upon removing the appliance from the replace
a tag shall be permanently attached to the
replace indicating it has been altered and
should be inspected by a qualied person prior to
re-use as a convectional replace (tag included
in component pack).
B. Tools And Supplies Needed
Tools and building supplies normally required for
installation, unless installing into an existing masonry
replace:
• Reciprocating Saw
• Channel Locks
• Hammer
• Phillips Screwdriver
• Tape Measure
• Plumb Line
• 1/4” Self-Tapping Screws
• Framing Material
• Hi-temp Caulking Material
• Gloves
• Safety Glasses
• Framing Square
• Electric Drill & Bits (1/4”)
• Level
May also need:
Vent Support Straps
Venting Paint
Risk of Fire!
• Damaged parts could impair safe operation.
• Do NOT install damaged, incomplete or
substitute components.
WARNING
WARNING
Hearth & Home Technologies disclaims any
responsibility for, and the warranty will be
voided by, the following actions:
• Installation and use of any damaged appliance.
• Modication of the appliance.
• Installation other than as instructed by Hearth &
Home Technologies.
• Installation and/or use of any component part not
approved by Hearth & Home Technologies.
• Operating appliance without fully assembling all
components.
• Operating appliance without legs attached (if supplied
with appliance).
• Do NOT Over re
Or any such action that may cause a re hazard.
C. Inspect Appliance and Components
• Open the appliance and remove all the parts and
articles packed inside the Component Pack. Inspect all
the parts and glass for shipping damage.
• Report to your dealer any parts damaged in shipment.
• All labels have been removed from the glass door.
• Plated surfaces have been wiped clean with a soft
cloth, if applicable.
• Read all the instructions before starting the
installation. Follow these instructions carefully
during the installation to ensure maximum safety
and benet.
• Follow pipe manufacturer instructions for
installation and air clearance requirements.

7September 27, 2018 7082-153D
TREKKER INSERT
D. Install Checklist
YES IF NO, WHY?
Verified clearance to combustibles.
Appliance is leveled and connector is secured to appliance.
Hearth extension size/height decided.
Outside air kit installed.
Floor protection requirements have been met.
If appliance is connected to a masonry chimney, it should be cleaned and
inspected by a professional. If installed to a factory built metal chimney, the
chimney must be installed according to the manufacturer’s instructions and
clearances.
Appliance Install
Chimney configuration complies with diagrams.
Chimney installed, locked and secured in place with proper clearance.
Chimney meets recommended height requirements (5 feet minimum vertical).
Roof flashing installed and sealed.
Terminations installed and sealed.
Venting/Chimney
Clearances
Verified all clearances meet installation manual requirements.
Mantels and wall projections comply with installation manual requirements.
Floor protection and heart extensions installed per manual requirements.
Appliance Setup
All protective materials removed.
All labels have been removed from the door.
All packaging materials are removed from inside/under appliance.
Manual bag and all of its contents are removed from inside/under the appliance
and given to the party responsible for use and operation.
WARNING! Risk of Fire or Explosion! Failure to install appliance to these instructions can lead to a fire or
explosion.
Hearth & Home Technologies recommends the following:
Photographing the installation and copying this checklist for your file.
That this checklist remain visible at all times on the appliance until the installation is complete.
Electrical
120 VAC unswitched power provided to the appliance.
Check outlet with multi-meter for proper polarity and voltage (115-120 VAC).
Record voltage reading: _____________
ATTENTION INSTALLER:
Follow this Standard Work Checklist
This standard work checklist is to be used by the installer in conjunction with, not instead of, the instructions contained in this installation manual.
Customer:
Date Installed:
Lot/Address:
Location of Appliance:
Installer:
Dealer/Distributor Phone Number:
Serial Number:
Model Name:
__________________________________________________________________________
______________________________________________________________________
_______________________________________________________________________
________________________________________________________________
___________________________________________________________________________
________________________________________________________
______________________________________________________________________
_______________________________________________________________________
Started appliance and verified that all motors and blowers operate as they should.
Checked draft using a Manometer. Record readings: ______________________
Comments: Further description of the issues, who is responsible (Installer/Builder/Other Trades, ets.) and corrective action needed:
Comments communicated to party responsible __________________________ by ______________________ on ____________
(Builder/Gen. Contractor) (Installer) (Date)
Checked vacuum using a Manometer. Record readings: ____________________

8September 27, 20187082-153D
TREKKER INSERT
Figure 8.5 - Front View with Basic Surround Panel Set
Figure 8.1 - Top View with Cast Panel Set
Figure 8.3 - Side View with Cast Panel Set
26-1/4 in [667mm]
14-1/8 in
[359mm]
15 in
[382mm]
13-1/8 in
[333 mm]
36-5/8 in [93 mm]
16-1/4 in
[413mm]
23-7/8 in [606mm]
32 in [814mm]
29-3/4 in
[756mm]
23-7/8 in
[605mm]
26-7/8 in [683mm]
11-7/8 in
[302mm]
24-1/8 in
[613mm]
33 in
[838mm]
50 in [1270mm]
34-1/2 in
[876mm]
45 in [1143mm]
11-3/4 in
[297mm]
18-1/2 in [469mm]
Figure 8.2 - Front View with Cast Panel Set
23-7/8 in [606mm]
32 in [814mm]
26-1/4 in [667mm]
14-1/4 in
[361mm]
15-1/8 in
[384mm]
13 in
[330mm]
36-5/8 in [930mm]
16-3/8 in
[415mm]
Figure 8.4 - Top View with Basic Surround Panel Set
29-3/4 in
[756mm]
23-7/8 in
[605mm]
26-7/8 in [683mm]
11-13/16 in
[300mm]
24-1/8 in
[613mm]
Figure 8.6 - Side View with Basic Surround Set
A. Appliance Dimensions
3 Dimensions and Clearances

9September 27, 2018 7082-153D
TREKKER INSERT
26-7/8 in.**
(683 mm)
19-3/8 in.*
(572 mm)
36 in.
(914 mm)
*If interior of chase will be drywalled, add the
thickness to this measurement.
**From finished floor protection. The size of
your floor protector choice must be added to
this dimension.
Figure 9.1
Built-in Appliance - Rear Vent
NOTE:
• Illustrations reect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.
B. Clearance to Combustibles, US & CAN
Fire Risk.
• Comply with all minimum clearances to
combustibles as specied.
Failure to comply may cause house re.
WARNING

10 September 27, 20187082-153D
TREKKER INSERT
Figure 10.2
Figure 10.3
C
DA
B
FIREPLACE FRONT SURFACE
USA 15-1/8
CANADA 15-1/8 (537mm)
41-3/4
1060mm
12in max *
MANTEL
Built-In Vertical
Figure 10.1
SIDE TRIM
SIDE WALL
TOP TRIM
18-5/16 in
(465mm)
24-5/16 in
(618mm)
HEARTH
EXTENSION
16
(406mm)
29-3/4 in
(1010mm)
If employing a hearth extension, any parts or materials
used in construction must be non-combustible.
HEARTH EXTENSION
No thermal protection required
Ember protection only!
*If mantel depth is 10 inches or less, than the height from
the hearth to the bottom of the mantel is 39-3/4 inches.
Minimum Opening
Dimensions Inches Millimeters
AHeight 24-3/8 619
B
Front Width (Steel Panel
Set) 32-1/4 819
Front Width (Cast Panel
Set) 32-1/4 819
CBack Width 24-1/8 613
DDepth (Steel Panel Set) 16-5/8 422
Depth (Cast Panel Set) 16-1/4 413
C. Minimum Opening for Masonry & ZC
Fireplaces
D. Hearth Extension
E. Floor Protection
Use a non-combustible ember oor protector, extending
beneath the appliance and to the front, and to the sides as
indicated in sub-section E. Floor Protection.
Figure 10.4
D
B

11September 27, 2018 7082-153D
TREKKER INSERT
Mark area of
floor to cut
Starter hole
Keep sharp edge of
metal floor away from
power cord
The following modications are permissible:
-Removal of damper or locked in open position
- Removal of smoke shelf or ba󰀪e
-Removal of ember catches
- Removal of re grate
-Removal of view screen/curtain
-Removal of doors
- Removal of factory-built replace oor
• External trim pieces which do not a󰀨ect the operation
of the replace may be removed providing they can be
stored on or within the replace for reassembly if the
insert is removed.
• The permanent metal warning label provided must be
attached to the back of the replace, with screws or
nails, stating that the replace may have been altered
to accommodate the insert, and must be returned to
original condition for use as a conventional replace
(Figure 11.1).
Figure 11.2 - Measure and mark the metal oor for cutting.
With a drill, make a starter hole in each corner.
Figure 11.3 - Using a saws-all, cut out the oor.
Figure 11.4 - Place the insert into the factory-built rebox.
Ensure that the power cord can not be damaged by the
sharp metal edge. You may need to cut out a notch to
accommodate the cord.
250-2061
WARNING
THIS FIREPLACE MAY HAVE BEEN ALTERED
TO ACCOMMODATE AN INSERT. IT MUST BE
RETURNED TO ITS ORIGINAL CONDITION
BEFORE USE AS A SOLID FUEL BURNING
FIREPLACE. 250-2061
Heath & Home Technologies
250-2061
5.5 in. width x 2 in. height
NON. ANOD. ALUM BLACK LETTERS ON SILVER
with 1/8 in. holes on both sides.
Black letters
Figure 11.1
• If the hearth extension is lower than the replace
opening, the portion of the insert extending onto the
hearth must be supported.
• Manufacturer designed adjustable support kit can be
ordered from your dealer.
The following is only one example as there are many
di󰀨erent models of factory-built replaces.
F. Installation into a Factory-Built Fireplace
NOTE: Refer to chimney liner manufacturer for
recommendations on supporting the liner.
Installation into replaces without a permit will
void the listing.
• The rebrick (refractory), glass doors, screen rails,
screen mesh and log grates can be removed from a
factory-built rebox in order to gain minimum insert
opening requirements.
• Any smoke shelves, shields and ba󰀪es may be
removed from a factory-built rebox if attached with
mechanical fasteners.
• The metal oor of the factory-built rebox may be
removed to facilitate the installation of the insert only
when a 1 inch (25mm) airspace is provided between
the insert and the oor of outer wrap.
NOTE: This example is for reference only. Any
modications must not compromise the structural
integrity or reduce the protection for combustible
materials.

12 September 27, 20187082-153D
TREKKER INSERT
NOTICE: In Canada when using a factory-built chimney
it must be safety listed, Type UL103 HT
(2100oF) [1149oC] CLASS “A” or conforming
to CAN/ULC-S629M, STANDARD FOR 650oC
FACTORY-BUILT CHIMNEYS.
The chimney can be new or existing, masonry or
prefabricated and must meet the following minimum
requirements:
- Must be minimum 6 inch (152mm) inside diameter
of high temperature chimney listed to UL 103 HT
(2100°F) or ULC-S628.
-Must use components required by the
manufacturer for installation.
-Must maintain clearances required by the
manufacturer for installation.
-Refer to manufacturers instructions for installation
- This insert is listed to ASTM E 1509-12 Standard
and is approved for installation into listed factory-
built zero clearance replaces listed to UL 127
conforming to the following specications and
instructions:
- The original factory-built clearance replace
chimney cap must be re-installed after installing the
approved chimney liner meeting type UL 103 HT
requirements (2100°F) per UL 1777.
-If the chimney is not listed as meeting HT
requirements, or if the factory built replace was
tested prior to 1998, a full height listed chimney
liner must be installed from the appliance ue collar
to the chimney top.
-The liner must be securely attached to the insert
ue collar and the chimney top.
- The air ow of the factory-built zero-clearance
replace system must not be altered. The ue liner
top support attachment must not reduce the air ow
for the existing air-cooled chimney system.
-No dilution air is allowed to enter the chimney.
1. Secure the replace damper in the open position. If this
cannot be accomplished, it will be necessary to remove
the damper.
2. Seal damper area of chimney around chimney
connector with a high temperature sealant or seal
insert against the face of the replace.
3. Both methods must be removable and replaceable for
cleaning and re-installation.
All modications that can be made to a Factory Built
Fireplace can be made to a Masonry Fireplace.
In addition DO NOT remove any brick or mortar from the
existing replace.
G. Installation into a Masonry Fireplace H. Prefabricated Metal Chimney
Risk of Fire!
Follow venting manufacturer’s clearances and
instructions when installing venting system.
WARNING
• Removing oor of replace must not weaken
structure of rebox or reduce protection for
combustible materials.
• Final approval of this installation type is contingent
upon the appropriate local authority having
jurisdiction.
WARNING

13September 27, 2018 7082-153D
TREKKER INSERT
4 Vent Information
A. Venting Termination Minimum Requirements
J or K
X
V
M
I
H
A
V
G
B
V
V
A
B
V
FV
C
B
B
E
L
V
D
V
Electrical
Service
V
N
VN
V
N
N
V
Inside Corner
FIXED
CLOSED
OPEN
OPEN
FIXED
CLOSED
VX
G
G
Termination Cap Air Supply Inlet Gas Meter Restricted Area
O
P
Figure 13.1
A12 in. Above Finish Grade (the grade surface must
be a non-combustible material
B12 in.
48 in. no OAK Open door or window: below or to the side
B12 in. Open door or window: above
C6 in. Permanently closed window: above, below or
to the side
D18 in.
36 in. no OAK
Vertical clearance to a ventilated so󰀩t located
above the terminal within a horizontal distance
of 2 ft from the center-line of the terminal
E12 in. Clearance to unventilated so󰀩t
F12 in. Clearance to outside corner
G12 in. Clearance to inside corner
H36 in. Above gas meter/regulator measured from
horizontal center-line of regulator
I36 in. USA
72 in. Canada Clearance to service regulator vent outlet
J12 in.
48 in. no OAK
Clearance to non-mechanical air supply inlet to
the building or the combustions air inlet to any
other appliance
K10 ft horizontal
3 ft vertical Clearance to mechanical air supply
L7 ft. Above paved sidewalk, paved driveway located
on public property
M12 in. Under an open veranda, porch, deck or
balcony
NSee Note
below*
Electric service: above, below or to the side
(location must not obstruct or interfere with
access)
O24 in. Adjacent building, fences and protruding parts
of the structure
P12 in. Clearance above roof line for vertical
terminations
All minimum clearances are listed with an Outside Air Kit (OAK) installed, unless otherwise noted in table below.
24 in. Above grass, top of plants, wood or any other
combustible
12 in.
36 in. no OAK Clearance from any forced air intake of other appliance
12 in. Clearance horizontally from combustible wall
15 in. Vented directly through a wall, minimum length of
horizontal pipe
6 in. horizontal
12 in. vertical
Minimum horizontal or vertical terminations must
protrude from wall
*NOTE: Consult local building, re o󰀩cials or authorities
having jurisdiction. Local codes or regulations
may require di󰀨erent clearances.
NOTICE
DO NOT TERMINATE VENT:
• In any location that will allow ue gases or soot from
entering or staining the building
• In any location which could create a nuisance or
hazard
• In any enclosed or semi-enclosed area such as a
carport, garage, attic, crawl space, under a sun deck
or porch, narrow walkway
• Closely fenced area, or any location that can build up
a concentration of fumes such as a stairwell, covered
breezeway, etc.
NOTICE
TERMINATION MUST EXHAUST ABOVE AIR INLET
ELEVATION:
• It is recommended that at least 60 inches (1.52m) of
vertical pipe be installed when appliance is vented
directly through a wall. This will create a natural draft,
which will help prevent the possibility of smoke or
odor venting into the home during a power outage.
• It will also keep exhaust from causing a nuisance
or hazard by exposing people or shrubs to high
temperatures.
• The safest and preferred venting method is to extend
the vent vertically through the roof or above the roof.

14 September 27, 20187082-153D
TREKKER INSERT
B. Avoiding Smoke and Odors
Negative Pressure, Shut-Down and Electrical Power
Failure
To reduce the probability of back-drafting or burn-back
in the pellet appliance during power failure or shut down
conditions, it must be able to draft naturally without exhaust
blower operation.
Negative pressure in the house will resist this natural draft if
not accounted for in the pellet appliance installation.
Heat rises in the house and leaks out at upper levels. This
air must be replaced with cold air from outdoors which
ows into lower levels of the house.
Vents and chimneys into basements and lower levels of the
house can become the conduit for air supply and reverse
under these conditions.
Outside Air
An outside air kit (OAK-3) is recommended in all
installations and must be ordered separately.
Per national building codes, consideration must be given
to combustion air supply to all combustion appliances.
Failure to supply adequate combustion air for all appliance
demands may lead to back drafting of those and other
appliances.
When the appliance is roof vented (strongly recommended):
-The air intake is best located on the exterior wall
oriented towards the prevailing wind direction
during the heating season.
When the appliance is side-wall vented:
-The air intake is best located on the same exterior
wall as the exhaust vent outlet and located lower
on the wall than the exhaust vent outlet.
The outside air supply kit can supply most of the demands
of the pellet appliance, but consideration must be given to
the total house demand.
House demand may consume the air needed for the
appliance. It may be necessary to add additional ventilation
to the space in which the pellet appliance is located.
Consult with your local HVAC professional to determine the
ventilation demands for your house.
Vent Congurations
When installing a pellet appliance with a horizontal vent
conguration the frequency of power outages should be
considered:
• Power outages during operation will cause the
appliance to immediately turn o󰀨 and may create
conditions where smoke will back draft into the house.
In order to reduce the likelihood of smoke back drafting
into the house during a power outage, Hearth and
Home Technologies strongly suggests:
-Installing the pellet venting with a minimum vertical
run of 5 feet (1.52m).
-Installing the outside air kit at least 4 feet (1.22m)
below the vent termination.
To prevent soot damage to exterior walls of the house and
to prevent re-entry of soot or ash into the house:
• Maintain specied clearances to windows, doors and
air inlets, including air conditioners.
• Vents should not be placed below ventilated so󰀩ts.
Run the vent above the roof.
• Avoid venting into alcove locations.
• Vents should not terminate under overhangs, decks or
onto covered porches.
• Maintain minimum clearance of 12 inches (305mm)
from the vent termination to the exterior wall. If you
see deposits developing on the wall, you may need to
extend this distance to accommodate your installation
conditions.
CAUTION
• DO NOT CONNECT THIS APPLIANCE TO
A CHIMNEY FLUE SERVICING ANOTHER
APPLIANCE.
• DO NOT CONNECT TO ANY AIR DISTRIBUTION
DUCT OR SYSTEM.

15September 27, 2018 7082-153D
TREKKER INSERT
C. Negative Pressure
D. Draft
E. Chimney and Exhaust Connection
Negative pressure results from the imbalance of air
available for the appliance to operate properly. It can be
strongest in lower levels of the house.
Causes include:
• Exhaust fans (kitchen, bath, etc.)
• Range hoods
• Combustion air requirements for furnaces, water
appliances and other combustion appliances
• Clothes dryers
• Location of return-air vents to furnace or air
conditioning
• Imbalances of the HVAC air handling system
• Upper level air leaks such as:
-Recessed lighting
-Attic hatch
-Duct leaks
To minimize the e󰀨ects of negative air pressure:
• Install the outside air kit with the intake facing prevailing
winds during the heating season
• Ensure adequate outdoor air for all combustion
appliances and exhaust equipment
• Ensure furnace and air conditioning return vents are
not located in the immediate vicinity of the appliance
• Avoid installing the appliance near doors, walkways or
small isolated spaces
• Recessed lighting should be a “sealed can” design
• Attic hatches weather stripped or sealed
• Attic mounted duct work and air handler joints and
seams taped or sealed
Risk of Asphyxiation!
Negative pressure can cause spillage of combustion
fumes and soot
WARNING
NOTICE: Hearth & Home Technologies assumes no
responsibility for the improper performance of
the chimney system caused by:
• Inadequate draft due to environmental conditions
• Down drafts
• Tight sealing construction of the structure
• Mechanical exhausting devices
Draft is the pressure di󰀨erence needed to vent an
appliance successfully. When an appliance is drafting
successfully, all combustion byproducts are exiting the
home through the chimney.
Install through the warm airspace enclosed by the building
envelope. This helps to produce more draft, especially
during lighting and die-down of the re.
Considerations for successful draft include:
• Preventing negative pressure
• Location of appliance and chimney
NOTE: The appliance exhaust outlet is designed to
accommodate 3 inch venting. Use of 4 inch
venting requires the use of a 3-to-4 inch exhaust
vent increaser in addition to any other venting
components needed, sold separately.
2. Mobile Home: Approved for all Listed pellet vent. If
using the 3 inch (76mm) vertical Top Vent Adapter
Kit or the 3 to 6 inch (76-152mm) Top Vent O󰀨set
Adapter, use Listed double wall ue connector. A
Quadra-Fire Outside Air Kit (OAK-3) must be used with
manufactured home installations.
3. Residential: The 3 inch (76mm) vertical Top Vent
Adapter Kit and the 3 to 6 inch (76-152mm) Top Vent
O󰀨set Adapter are tested to use 24 gauge single wall
ue connector or Listed double wall ue connector to
Class A Listed metal chimneys, or masonry chimneys
meeting International Residential Code standards for
solid fuel appliances.
4. INSTALL VENT AT CLEARANCE SPECIFIED BY THE
VENT MANUFACTURER.
5. Secure exhaust venting system to the appliance with
at least 3 screws. Also secure all connector pipe joints
with at least 3 screws through each joint.
6. DO NOT INSTALL A FLUE DAMPER IN THE
EXHAUST VENTING SYSTEM OF THIS APPLIANCE.
7. DO NOT CONNECT THIS APPLIANCE TO A
CHIMNEY FLUE SERVING ANOTHER APPLIANCE.
1. Chimney & Connector: Use 3 or 4 inch (76-102mm)
diameter type “L” or “PL” venting system. It can be
vented vertically or horizontally.
NOTE: All pipe must be welded seam pipe whenever
possible. Seal pipe joints with high temperature
silicone (500°F [260°C] minimum rated only).
WARNING
USE ONLY RECOMMENDED VENTING
COMPONENTS; OTHERWISE MAKESHIFT PARTS
MAY RESULT IN PROPERTY DAMAGE, PERSONAL
INJURY, OR DEATH.

16 September 27, 20187082-153D
TREKKER INSERT
The table below can help you calculate the equivalent feet
of pipe which is a method used to determine pellet vent
size (Figure 16.1).
F. Equivalent Feet of Pipe
Vent surfaces get HOT, can cause burns
if touched. Non-combustible shielding or
guards may be required.
WARNING
Example of 3 Elbow-Rear Vent Termination Calculation
Figure 16.1
2 ft.
2 ft.
3 ft.
2 ft.
Pellet
Venting
Component
# of
Elbows
Feet
of
Pipe
Multiplied
By
Equivalent
Feet
Components
Equivalent
Feet
90° Elbow or
Tee
3 X 5 15
45° Elbow X 3
Horizontal
Pipe
7 X 1 7
Vertical Pipe 2 X 0.5 1
Total Equivalent Feet 23
NOTE: This is a generic example and is not intended to represent any specic
fuel type.
Figure 16.2
3 in. or 4 in. (76mm or 102mm) Diameter Pipe
Equivalent Pipe
Length In Feet
ALTITUDE IN THOUSANDS OF FEET
0
20
30
1 2 3 4 5 6 7 8 9 10
4 in. (102mm) Diameter Pipe Only
10
Example 1
Example 2
Example 1: If the equivalent length of pipe is 23 feet (7m)
with altitude of 8,000 feet (2438m) you must use
4 inch (102mm) diameter type “L” or “PL” vent.
Example 2: If the equivalent length of pipe is 12 feet (3.7m)
with altitude of 6,000 feet (1829m) you may use 3
or 4 inch (76 to 102mm) diameter type “L” or “PL”
vent.
G. Pipe Selection Chart
The chart will help you in determining proper venting
size according to the equivalent feet of pipe calculated
previously and the altitude above sea level of this
installation (Figure 16.2).
1. Locate the calculated equivalent feet of pipe on the
vertical left side of the chart.
2. Move to the right horizontally on the chart until you
reach your altitude above sea level.
3. If you fall below the diagonal line, 3 or 4 inch (76 to
102mm) pipe may be used.
4. If it is anywhere above the diagonal line, a 4 inch
(102mm) diameter pipe is required.
• A 90° elbow is 5 times as restrictive to the ow of
exhaust gases under positive pressure as 1 foot
(305mm) of horizontal pipe.
• A foot of horizontal pipe is twice as restrictive as a
foot of vertical pipe.
NOTICE
Risk of Injury or Property Damage.
• Improper installation, adjustment, alteration,
service or maintenance can cause injury or
property damage.
• Refer to the owner’s information manual
provided with this appliance.
• For assistance or additional information
consult a qualied installer, service agency
or your dealer.
WARNING
Risk of Fire!
• Only LISTED venting components may be
used.
• NO OTHER vent components may be
used.
• Substitute or damaged vent components
may impair safe operation.
WARNING

17September 27, 2018 7082-153D
TREKKER INSERT
Figure 17.1
NOTE: Use metal plate around
exhaust vent pipe and seal all edges
with non-flammable insulation such
as fiberglass, mineral wool or
ceramic.
Do not use high temperature
caulking materials to seal any edge
to prevent future serviceability.
Outside Air
Termination
5 Venting Systems
A. Full Reline wit Outside Air - Horizontal
CAUTION
Never draw outside combustion air from:
• Wall, oor or ceiling cavity
• Enclosed space such as an attic or garage
Fire Risk.
Inspection of Chimney:
• Masonry chimney must be in good
condition.
• Meets minimum standard of NFPA 211
• Factory-built chimney must be a minimum 6
inch (152mm) UL103 HT.
WARNING
NOTE: In Canada, where passage through a wall or
partition of combustible construction is desired,
the installation shall conform to CAN/CSA-B365
NOTE:
• Illustrations reect typical installations and are FOR
DESIGN PURPOSES ONLY.
• Illustrations/diagrams are not drawn to scale.
• Actual installation may vary due to individual design
preference.

18 September 27, 20187082-153D
TREKKER INSERT
NOTE: Check clearances carefully for this type of
installation to ensure adequate room for outside
air venting.
NOTE: In Canada only a full reline is allowed per ULC
S628, ORD ULC C1482-M1990.
Figure 18.1
NOTE: Use metal plate around
exhaust vent pipe and seal all edges
with non-flammable insulation such
as fiberglass, mineral wool or
ceramic.
Do not use high temperature
caulking materials to seal any edge
to prevent future serviceability.
Outside Air
Termination at
Chimney Top
(Vertical)
12 in [305mm]
min. below
12 in [305mm]
min. below
NOTE: In Canada this replace insert must be installed
with a continuous chimney liner extending from
the replace insert to the top of the chimney.
The chimney liner must conform to the Class 3
requirements of CAN/ULC-S635, Standard for
Lining Systems for Existing Masonry or Factory-
Built Chimneys and Vents, or CAN/ULC-S640,
Standard for Lining Systems for New Masonry
Chimneys.
B. Full Reline with Outside Air - Vertical
Check building codes prior to installation.
• Installation MUST comply with local, regional, state
and national codes and regulations.
• Consult local building, re o󰀩cials or authorities
having jurisdiction about restrictions, installation
inspection, and permits.
CAUTION

19September 27, 2018 7082-153D
TREKKER INSERT
The leveling bolts are located on the sides of the appliance,
front and rear. To access the bolts, remove the front access
panels. Reach in and turn the bolt to the desired height to
level the appliance (Figure 19.1).
Included in Kit: 2 wire ties, 1 collar assembly, 1
termination cap assembly, 1 trim ring, fasteners.
3 INCH (76mm) ALUMINUM FLEX PIPE NOT INCLUDED
Tools Needed: Phillips head screw driver; wire cutters;
hole saw or jig saw.
1. Measure distance from oor to air vent opening in
appliance and mark location on wall.
2. Use saw to cut opening in wall. Cut a 3-1/2 to 4 inch
(89-102mm) opening on inside wall and a 4 to 4-1/2
inch (102-114mm) opening on outside of house.
3. Use wire ties to secure ex pipe to collar assembly.
4. Slide trim ring over ex pipe and run pipe through wall.
5. Attach ex pipe (not included) to outside termination
cap with second wire tie.
6. Secure termination cap to outside surface.
7. Secure trim ring to interior wall.
Figure 19.1
Collar
Wire Ties
Trim Ring
Termination Cap
3 inch Aluminum Flex
Pipe (not included)
Figure 19.2 - OAK Exploded View
Lower the leveling
bolts if necessary to
keep the insert level
when installing.
Figure 19.3
Bend tabs down. Shipped
flat from the factory.
Included in Kit: (1) bottom, (1) trim front, (2) trim sides, (2)
trim extensions
Tools Needed: Phillips head screw driver, measuring tape,
gloves
1. Remove contents from box and lay on protective
surface to avoid scratching the paint.
2. Lay front and sides face down. Bend the tabs down
toward the inside (Figure 18.3).
3. The side pieces are shipped at. It is must easier to
ex the sides into a bowed position before installing.
4. Lay the cast bottom face up. Attach the 2 sides FIRST
and then the front piece (Figure 19.1 on pg. 19).
5. Turn the cast bottom right side up and attach the panel
extensions. Note the alignment hole.
6. Attach the appropriate footers depending on the panels
& trim set you are installing. The footers come in 2
sizes, 3 and 5 inches. Discard the footers not used.
7. Place the assembled hearth support under the insert.
Lower the leveling bolts if necessary to keep the insert
level.
8. Open the door and attach the hearth support to the
insert. There are 9 attachment holes (Figure 19.2 on
pg. 19).
6 Appliance Set-Up
A. Leveling System
B. Outside Air Kit Instructions
C. Hearth Support
CAUTION
Never draw outside combustion air from:
• Wall, oor or ceiling cavity
• Enclosed space such as an attic or garage

20 September 27, 20187082-153D
TREKKER INSERT
Figure 20.3 - Shown with Cast Panel Set
Basic
Cast
Attach Trim to Base
from underneath
Attach Trim to Insert from
inside Insert.
Install Front Trim Last,
Corner Overlap Side
Trim Pieces
5 in
3 in
5 inch
high Set
3 inch
high Set
Location of Latch
for Removing
Cast Sides
Lower the leveling
bolts if necessary to
keep the insert level
when installing the
Hearth Support.
Remove the cast side by releasing the upper, spring-loaded
latch. Access the latch through the upper panel vent holes.
The cast panel should fall forward. Lift it out of its lower
nest and set the panel aside.
Figure 20.1
9 attachment holes - 3 on
each side and 3 in the front
Figure 20.2
Included in Surround Kit: (2) side panels, left and right;
(1) panel top; (1) fastener package.
Included in Cast Trim Kit: (2) cast trim legs, left and right;
(1) cast trim header; (2) cast trim footers, left and right; (1)
fastener package.
Tools Needed: Powered Phillips head screw driver
1. Remove contents from box being careful not to scratch
or damage the cast trim pieces.
2. Lay the surround set face down on protective covering
to prevent scratching the painted surface.
3. Secure the surround legs to top panel with the screws
provided.
4. Now bend the tabs down toward the backside of the
panel set, 5 on top and 2 on each leg. Leave the panel
set face down (Figure 20.4).
5. Place the corresponding cast trim pieces ( 2 cast trim
legs and 1 cast trim header) underneath the panel set,
also face down.
6. Place washer provided over tab and secure the trim
and panel together with screw. Continue for all tabs.
7. Secure cast footers with screws.
8. Remove both left and right cast sides from insert (See
Figure 20.3).
9. Carefully slide surround and trim over the top of the
insert into place matching the mounting holes on the
panel with the mounting holes on the insert. Secure
with screws provided.
Figure 20.4
Figure 20.5- Completed View
1. Screw panels
together
2. Bend tabs down
1. Screw panels
together
3. Install Cast Trim Header
2. Bend tabs
down
D. Removal of Cast Sides
E. Surround & Cast Trim Set