Quatro Premium SPH Series Instructions for use

30 Hymu
s
R
C
---------------
-
s
Boulevard, Mo
P
R
EAD AN
STO
R
TH
C
OULD
C
-
----------------
-
ntreal, Quebec,
P
rem
i
In
s
D UNDE
R
R
E THE
M
IS MANU
C
AUSE D
A
-
-----------------
H9R 1C9 Tel.
S
i
um
T
s
tructi
o
R
STAND
M
ANUAL
AL CON
T
W
A
MAGE
T
----------
W
e
M
: (514) 630-444
4
S
PH &
A
T
urb
i
o
n &
M
THIS MA
IN A SA
F
T
AINS C
R
W
HICH IF
T
O THE
S
M
ake Clean
A
4
Fax: (514) 63
0
A
F800
S
i
ne D
u
M
ainte
n
NU
A
L B
E
F
E PLAC
E
R
ITICAL
O
NOT FO
L
S
YSTYE
M
A
i
r
-----------
-
0
-4454 websit
e
S
eries
ust
C
n
ance
E
FORE O
E
FOR F
U
O
PERATI
N
L
LOWED
M
NOT C
O
-
----------------
-
e
: www.QUATR
O
C
olle
c
Manu
a
PERATI
N
U
TURE R
N
G INFO
O
VERED
Q
-
-----------------
O
-air.com info
@
c
tor
s
al
N
G THE
S
EFEREN
C
RMATIO
N
BY WAR
R
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
s
S
YSTEM
C
E
N
R
ANTY.
O
I
nc.
m

QUATRO
Air Technologies Inc.
------------------------------------------------------------ We Make Clean Air ----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: [phone] Fax: [phone] website: www.QUATRO-air.com i[email protected]
1- INTRODUCTION
You are now the owner of a QUATRO SPH Or AF System, an advanced effective indoor dust and fume collection system
designed specifically to remove particulate matter and odor causing gas phase contaminants at the source. You can expect a
noticeable improvement in air quality as the SPH Or AF System begins the process of reducing microscopic airborne
particulate.
The SPH or AF System normally features 3 Or 4 stages of filtration:
1) An OPTIONAL Pre Filter Pad OR Knock Out Pad. This captures large debris.
2) A Pre Filter for larger particles.
3) A HEPA filter captures & holds fine particles protecting the motor and ensuring a clean output.
4) A Chemical Filter to absorb & contain odor causing gas phase contaminants.
The filter sequence can be customized to your application. Contact Quatro Air for more info.
WARNING – To reduce the risk of damage to your system read and follow all instructions. Failure to follow these
guidelines may result in undesired operation or damage that will not be covered under warranty.
2- WHAT’S IN THE BOX
The SPH model comes with the “Laser Blue” Gel filter seal. The AF model comes with a gasket seal.
Models Name Accessories
835
835L
82B5
SPH Or AF800 230V c/w “Quick Change” Motors
SPH Or AF800 230V c/w “Long Life” Motors
SPH Or AF400 230V c/w “Brushless” Motors
(1) O&M Manual
(1) Power Cord
(2) Clamps Per Inlet (No Clamps For 1.5”)
(1) Piece Of The Appropriate Size Hose (Per Inlet)
(1) Remote Cable (AE427) Only For Units Equipped With
DB9 Remote Connector
(2) Locking HD Casters
(2) HD Casters
3- IMPORTANT SAFETY & INSTALLATION PRECAUTIONS
- Ensure to use proper voltage as indicated on the system.
- To reduce the risk of electric shock, do not expose to excessive moisture, water or rain.
- Use only on a grounded electrical circuit.
- Do not install or operate the system in an enclosed space or against a wall. Unit may overheat & shut down.
- Keep all objects at least 6” away from the casing, especially the discharge grill.
- All filters must be in place whenever this machine is in operation.
- ALWAYS turn system on/off switch to off and disconnect power prior to accessing unit, replacing filters, or servicing motor(s).
- Allow the unit to cool for 45 minutes before performing any service to the motor(s).
- Do not kink hose or restrict airflow in any way.
SAVE THESE INSTRUCTION FOR FUTURE REFERENCE
Failure to follow these guidelines may result in undesired operation or damage, not covered under this warranty.
4- INSTALLATION
1) Install the Casters on the bottom, following the instructions included with them, and then Install the unit in the chosen
location for it.
2) Open the filter access door & lid and install the filters in the correct order. See the “Filter Service & Replacement”
section for more info.
3) Connect the supplied hose from the Quatro System to the Laser/Printer.
4) Connect the power cord to the unit and then to the power source. VERIFY VOLTAGE BEFORE CONNECTING.
- ONLY USE THE POWER CORD SUPPLIED WITH THE EQUIPMENT.
- Always plug the unit directly into the wall outlet. Do not use extension cords or power bars.
- Ideally the unit should be plugged into it’s own dedicated circuit.
- The system is designed to be constantly powered (plugged in). The system will not function correctly and may get
damaged if power source is used to control the operation. See “Controls” for more info.
5) Turn unit on & adjust the desired airflow using the arrow up and down keys. Set airflow to lowest acceptable level to
properly evacuate your equipment.
For information about remote operation see the “Controls” section.

30 Hymu
s
WA
R
Imp
o
NON
See
t
5-
C
Typ
e
The
“
safe
t
A
dju
s
Typ
e
IMP
O
Do n
o
Nev
e
cont
r
We
h
“iSe
r
The i
that i
audi
b
C
R
---------------
-
s
Boulevard, Mo
R
NING: DO N
o
rtant Notes:
E of the filter
s
t
he “Filter Se
r
C
ONTROL
S
e
1 – Basic
C
“
Basic” contr
o
t
y circuit brea
s
t the speed
o
e
2 – iSeries
O
RTANT NO
T
o
t connect th
e
e
r use any fo
r
r
ols and mot
o
h
ave many p
o
r
ies” Contro
Series contr
o
ndicate the s
t
b
le alert. See
C
ircuit Break
e
R
otary Spee
d
-
----------------
-
ntreal, Quebec,
OT OPERAT
s
in the syst
e
r
vice & Repl
a
S
C
ontrols
o
ls feature a
P
ker (reset) a
r
o
f the motor(
s
C
ontrols
T
ES FOR P
R
e
main powe
r
r
m of remote
c
o
rs may occu
r
o
wer switchin
g
ls & Alarms
/
o
ls feature so
f
t
atus of the fi
the table on
t
e
r
d
Control
-
-----------------
H9R 1C9 Tel.
E UNIT UNL
E
e
m are clean
a
a
cement” Sec
P
ower (On/O
f
r
e also on th
e
s
) to the lowe
R
OPER FUN
C
r
cord to an
o
c
ontrol that s
w
r
. Contact Q
U
g
adaptors a
v
Status Con
d
f
t touch Pow
e
lter(s) and m
o
t
he following
----------
W
e
M
: (514) 630-444
4
E
SS ALL FIL
T
a
ble. They wil
tion for more
f
f) switch, an
d
e
face of the
p
s
t acceptable
C
TION OF T
H
o
utlet that is c
o
w
itches the p
U
ATR
O
if po
w
v
ailable for S
A
d
itions
e
r (On/Off), S
o
tor(s) and in
page to und
e
M
ake Clean
A
4
Fax: (514) 63
0
T
ERS ARE I
N
l all need to
b
info.
d
a rotary sp
e
p
anel.
level to prop
e
H
E CONTRO
L
o
ntrolled by
a
ower source
w
er switching
A
FE and reli
a
peed Up & S
form you of
a
e
rstand the m
A
i
r
-----------
-
0
-4454 websit
e
N
PLACE.
b
e removed
a
e
ed control k
n
e
rly evacuate
L
S:
a
switch.
on and off. I
n
is the only w
a
a
ble control.
peed Down
B
a
ny alarms. T
h
eanings of th
-
----------------
-
e
: www.QUATR
O
a
nd disposed
n
ob. The po
w
your equipm
n
doing so, s
e
a
y you have
t
B
uttons. It als
hese alarms
h
e LEDs and
t
Q
-
-----------------
O
-air.com info
@
of periodicall
y
w
er cord conn
e
ent.
e
rious damag
e
t
o remotely c
o
o features a
s
are accompa
t
he alarms.
Power Cord
On/Off Swit
c
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
y
.
e
ction and th
e
e
to the
o
ntrol the uni
t
s
eries of LE
D
nied by an
c
h
O
I
nc.
m
e
t
.
D
s

30 Hymu
s
Alar
m
Alar
m
All al
agai
n
Whe
n
hour
To
m
start
If th
e
Mut
e
If th
e
turn
e
Circuit
B
Power
DB9 R
e
---------------
-
s
Boulevard, Mo
m
s & Status
m
Mute Feat
u
arms can be
n
.
n
mute is en
a
mute period
m
ute: Press S
P
flashing. Ala
r
e
re are any a
d
e
d alarms will
e
unit is turne
d
e
d on again.
B
reaker
Inlet
e
mote
-
----------------
-
ntreal, Quebec,
Conditions
u
re
muted for a
p
a
bled, L1 Fla
s
is over.
P
D UP & DN
r
m LED will g
o
d
ditional alar
m
only be displ
a
d
off and the
n
-
-----------------
H9R 1C9 Tel.
p
eriod of 8 h
o
s
hes & the m
u
quickly at th
e
o
SOLID.
m
s when MU
T
a
yed while th
n
on during th
----------
W
e
M
: (514) 630-444
4
o
urs OPERA
T
u
ted alarms
s
e
same time.
W
T
ED, mute wi
e unit is in o
p
e 8 hour mut
e
M
ake Clean
A
4
Fax: (514) 63
0
T
ING TIME.
A
s
tay SOLID.
T
W
hen the bu
t
ll disable itse
p
eration.
e
, the balanc
e
A
i
r
-----------
-
0
-4454 websit
e
A
fter 8 hours t
T
he level of t
h
t
tons are rel
e
lf until muted
e
of the 8 ho
u
-
----------------
-
e
: www.QUATR
O
t
he alarm will
h
e alert will n
o
e
ased the ala
r
again, then
B
u
r mute will c
o
Q
-
-----------------
O
-air.com info
@
return and c
a
o
t be display
e
r
m(s) will mu
t
B
OTH alarm
s
o
ntinue after
S
L
S
O
L
S
L
L
S
O
R
L
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
a
n be muted
e
d until the 8
t
e & L1 will
s
will be mute
the unit is
S
ervice Filter
s
L
ED 3 (L3)
S
ystem
O
N
L
ED 1
(
L1
)
S
ervice Moto
r
L
ED 2 (L2)
L
ED 4 (L4)
S
ettings Men
u
O
nly
R
emote/Stan
d
L
ED 5 (L5)
O
I
nc.
m
d
.
s
r
(s)
u
d
by

QUATRO
Air Technologies Inc.
------------------------------------------------------------ We Make Clean Air ----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: [phone] Fax: [phone] website: www.QUATRO-air.com i[email protected]
LED Diagnostics Table R17.0 And Higher
Light
(LED) Status Audible Alert Condition Description/Action
System SOLID Unit is ON
ON
LED 1 Fading IN-OUT Temporary ON Mode POWER Button Had Been Used To Temporarily Turn Unit On While In Remote Mode See “Temporary ON Mode” On Next Page
(L1) Flashing
Slowly AUDIBLE ALERT MUTED Alarm Condition MUTED, See L2 OR L3 For Specific Alarm Condition
Service
Motors
LED 2
(L2)
SOLID Beep
Every
4 Hrs
Motor(s) Will Soon Need
Service “Quick Change” Brush Motor(s) WILL SOON Require Brush Replacement Infinity Brush Motor(s) WILL SOON Require Complete Replacement
Brushless Motor Is Almost At The End Of The Predicted Service Life
RESET ALERT After Service
See “Motor Service & Replacement” Section For More Motor Info & Reset Alert
Instructions
SOLID Beep
Every
15 Min
Motor(s) Service
Becoming Urgent “Quick Change” Brush Motors ONLY: Replace Brushes ASAP And RESET ALERT See “Motor Service & Replacement” Section For More Info & Reset Alert Instructions
SOLID Beep
Every 5
Min
Motor(s) Service
Required
IMMEDIATELY
“Quick Change” Brush Motors ONLY: Replace Brushes IMMEDIATELY And RESET
ALERT
See “Motor Service & Replacement” Section For More Info & Reset Alert Instructions
SOLID Motor Alarm Muted
L1 Flashing Slowly Replace Brushes OR Motor(s) ASAP And RESET ALERT Alarm Mute Details On Previous Page
See “Motor Service & Replacement” Section For More Motor Info & Reset Alert
Instructions
Service
Filter(s)
LED 3
Flashing
Slowly Filter Pressure High Prepare To Service/Replace Filters See “Filter Service & Replacement” Section For More Info On “On Demand”
Filter Cleaning & Filter Service/Replacement Instructions
(L3) Flashing
Slowly Beep Every Hour Filter Pressure Near Critical.
Service Becoming Urgent
Replace Filters.
Continued Operation May Result In Unit Shutdown.
High Pressure Causes Excess Motor Heat & Accelerates Brush Wear.
See “Filter Service & Replacement” Section For More Info & Filter
Service/Replacement Instructions
Flashing
Slowly Beep Every
Second
Critical Pressure Unit Has Shutdown To Prevent Damage From Excess Pressure
Verify Blockage – Remove Blockage
Verify All Filters – Clean/Replace Filters Accordingly
See “Filter Service & Replacement” Section For More Info
SOLID Beep
Every Hour Filter(s) Service Life Expired Replace Filter(s) ASAP And RESET ALERT See “Filter Service & Replacement” Section For More Info & Reset Alert Instructions
SOLID Filter Alarm Muted
L1 Flashing Slowly Replace Filter(s) ASAP And RESET ALERT Alarm Mute Details On Previous Page
See “Filter Service & Replacement” Section For More Info & Reset Alert Instructions
Remote SOLID Receiving Remote Signal Remote Switch Closed (On) OR Receiving Remote Signal From Another Piece Of
Equipment
Standby
LED 5 Fading IN-OUT Shutdown Delay Quatro System Continues To Run For 30-45 Seconds To Remove All Debris From Work Area
(L5) Flashing
Slowly Unit Is In Standby Waiting For Remote Switch To Close (Turn On) OR To Receiving Remote Signal From Another Piece Of Equipment
ALL
LEDS Flashing Slowly Beep Every
Second
Low System Pressure Abnormally Low Pressure, Unit will BEEP & Shutdown In 5 Seconds
Unit Will Continue To Shutdown Unit Until The Issue Is Addressed
-Motor(s) Not Operating Due To Service Required Or Failure
See “Motor Service & Replacement” Section For More Motor Info & Reset Alert
Instructions
-Motors Not Operating Due To Excess Heat.
See “Filter Service & Replacement” Section For More Info & Reset Alert Instructions
-Access Door(s) Open. Close All Access Doors
-Filters Not Or Improperly Installed. Verify Filters

30 Hymu
s
Nor
m
Man
u
V
ari
a
Spe
e
locat
e
“AU
T
prop
e
incre
chan
adeq
Rem
The
Q
rem
o
som
e
The
Q
Swi
t
unit
.
Tem
p
A
llo
w
surf
a
tem
p
To in
‐
‐
Ope
r
Con
n
requi
---------------
-
s
Boulevard, Mo
m
al (Manual)
u
al operation
a
ble Digital
S
e
d control is
a
e
d just unde
r
T
OFLOW” is
e
rly evacuat
e
ased pressu
r
ge, system
w
uate ventilati
o
ote (Autom
a
Q
uatro Syste
o
te status mo
n
e
custom re
m
Q
uatro Syste
t
ching pow
e
.
p
orary ON
M
w
s you to tem
a
ce. Tempora
p
orarily BLO
C
itiate:
Press PO
When yo
u
r
ation, Conn
e
n
ect the AE4
2
i
red as per th
-
----------------
-
ntreal, Quebec,
Operation
of the unit is
S
peed Contr
o
a
vailable in al
l
r
the POWE
R
an automatic
e
your equip
m
r
e as a result
w
ill automatic
a
o
n after a filt
e
a
tic) Operati
o
mis designe
d
n
itoring. The
c
ote cables fo
msupports “
C
e
r to contr
o
M
ode
porarily over
r
ry ON Mode
i
C
K OR DIES
N
WER (On/Of
f
u
finish using
e
ction & En
a
2
7 remote ca
b
e
diagram b
e
-
-----------------
H9R 1C9 Tel.
accomplishe
d
o
l & “AUTO
F
l
modes of o
p
button.
system pres
s
m
ent, the cont
r
of filters getti
a
lly decrease
e
r change. If
n
o
n & Remot
e
d
to be used
w
c
onnection i
s
r specific ap
p
C
losed Cont
a
o
l the QUAT
R
r
ide your aut
o
i
s only availa
b
N
GAGE all ot
h
f
) button to st
this feature,
p
a
bling
b
le in betwee
e
low.
----------
W
e
M
: (514) 630-444
4
d
by using th
e
F
LOW”
p
eration (man
s
ure compen
r
ols will auto
m
ng dirty or a
s
the speed to
n
ot adjust bl
o
e
Status
w
ith other pi
e
s
made using
p
lications. Co
n
a
ct” & “1-30V
A
R
O System
s
o
matic remot
e
b
le when the
h
er functions.
art unit, “Sys
t
p
ress POWE
R
n the Quatro
M
ake Clean
A
4
Fax: (514) 63
0
e
(Red) ON/
O
ual & autom
a
sation syste
m
m
atically incr
e
s
ystem block
a
the original
s
o
wer speed.
e
ces of equip
m
the AE427
Q
n
tact us for
m
A
C or DC” r
e
s
ystem re
m
e
control of th
e
Remote/Sta
n
t
em ON” LE
D
R
(On/Off) a
g
System & th
e
A
i
r
-----------
-
0
-4454 websit
e
O
FF POWER
a
tic) and is a
d
m
. After setti
n
e
ase the mot
o
a
ge until ma
x
s
et point. Ple
a
m
ent that ca
n
Q
UATRO Uni
v
m
ore info on
a
e
mote operati
o
m
otely WILL
e system to
p
n
dby (L5) ligh
D
will FADE I
n
g
ain. All othe
r
e
other piece
-
----------------
-
e
: www.QUATR
O
button.
d
justed with t
h
n
g the minim
u
o
r speed to c
o
x
imum speed
a
se verify tha
t
n
support re
m
v
ersal Remot
e
a
vailable appl
o
n as well as
L
NOT WOR
p
erform a “qu
h
t is flashing
s
n
-Out, unit wil
r
functions wi
l
of equipmen
t
Q
-
-----------------
O
-air.com info
@
h
e UP & DO
W
u
m speed re
q
o
mpensate f
o
is reached.
A
t you are ach
m
ote operatio
n
e
Cable. QU
A
ications and
p
“Remote St
a
K and can
d
ick cleaning”
s
lowly. Use o
f
l start.
l
l be un-bloc
k
t
using only t
h
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
W
N arrows
q
uired to
o
r the
A
fter a filter
ieving
n
and/or
A
TRO has
p
art number
s
a
tus” signals.
d
amage th
e
of work
f
this mode w
k
ed.
h
e wires
O
I
nc.
m
.
e
ill

QUATRO
Air Technologies Inc.
------------------------------------------------------------ We Make Clean Air ----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: [phone] Fax: [phone] website: www.QUATRO-air.com i[email protected]
Remote Operation
If choosing the Dry Contact (closed contact) remote option, connect the black and red wires to anything that can close a
contact and short these 2 wires together.
If choosing the 1-30V AC/DC remote option, connect the white & the green wires to the remote signal. RESPECT THE
INDICATED POLARITY WHEN MAKING THIS CONNECTION. DO NOT EXCEED 30V AC/DC.
To enable the remote system startup for either remote option, first plug the system into power and then connect remote
cable. Then simply have the other piece of equipment close (short) the dry contact or supply a remote control voltage.
When the unit is stopped the Quatro System will shut down after a short delay.
After Remote Sensing Has Been Activated
If the unit is RECEIVING a remote signal: “System ON” & “Remote ON” Lights will be FULLY Illuminated
If the unit is WAITING FOR a remote signal: “System ON” will be OFF & “Remote ON” Lights will be FLASHING
Unplugging the power cord will automatically deactivate Remote Sensing Feature.
Remote Status
The System can output status signals to you equipment.
The Run Signal contact is CLOSED whenever the system is turned on (motor(s) are functioning).
The contact is OPEN when the unit is turned off (motor(s) are not functioning). This includes when the unit goes into
Remote/Standby & if the unit shuts down due to a problem.
Run signal will NOT open when the motor(s) shut off for a filter cleaning when operating in “Online” filter cleaning mode.
Critical Filter Pressure Alarms (high & low pressure) will OPEN the Run Signal and shut the motor(s) off.
The Fault Signal can be used either with a Normally Open (NO) or Normally Closed (NC) contact depending on which wire
you choose to use (see diagram on previous page).
When there ARE NO alarm conditions present the NO contact will remain open and the NC contact will remain closed.
When there ARE alarm conditions the NO contact will CLOSE and the NC contact will OPEN.
ALL LEVELS of Filter & Motor(s) service alarms will trip the Fault Signal.
The Quatro Run Signal can only shut down the piece of equipment controlling it remotely if the piece of equipment
supports that function. The piece of equipment must be set or programmed to shut itself off when the Quatro Run
signal is OPENED. Contact your equipment manufacturer to verify if your equipment supports that function.
The status signals can either return a “signal” provided by your equipment or output a 12VDC+ or 12VDC- depending on
how the AE427 remote cable is wired. The Quatro System uses a single “common” for both the Run & Fault Signals.
To return a “signal” connect your signal to the Brown wire (Pin 5).
The “returned” Run signal is available on the Violet wire (Pin 9).
The “returned” Fault NC (Normally Closed) is available on the Blue wire (Pin 6).
The “returned” Fault NO (Normally Open) is available on the Orange wire (Pin 7).
To be supplied with a 12vdc signal where the + is being switched connect the Yellow Wire (Pin 8) to the Brown wire (Pin 5).
The 12VDC+ Run signal is available across the Violet wire (Pin 9+) & the Black Wire (Pin 1-).
The 12VDC+ Fault NC (Normally Closed) is available across the Blue wire (Pin 6+) & the Black Wire (Pin 1-).
The 12VDC+ Fault NO (Normally Open) is available across the Orange wire (Pin 7+) & the Black Wire (Pin 1-).
Any combination of the Dry Contact, Run Signal & Fault Signal being used means the Black Wire (Pin 1) must be shared.
To be supplied with a 12vdc signal where the - is being switched connect the Black Wire (Pin 1) to the Brown wire (Pin 5).
The 12VDC- Run signal is available across the Violet wire (Pin 9-) & the Yellow Wire (Pin 8+).
The 12VDC+ Fault NC (Normally Closed) is available across the Blue wire (Pin 6-) & the Yellow Wire (Pin 8+)
The 12VDC+ Fault NO (Normally Open) is available across the Orange wire (Pin 7-) & the Yellow Wire (Pin 8+).
Any combination of the Dry Contact, Run Signal & Fault Signal being used means the Black Wire (Pin 1) must be shared.
Your “signal” will be managed as indicated on the table below. The combination of the Run & Fault Signals can tell you if
the unit is still running but has an alarm condition or if there is an alarm condition and the unit has shut down completely.
Run Signal
Contact Fault Signal Contact Condition
Closed NC: Closed
NO: Open Unit Is Operating Normally
Closed NC: Open
NO: Closed Unit Is Operating Normally Motors or Filters Will Require Service Soon
See QUATRO System Control Panel & LED Diagnostic Table For More Info
Open NC: Open
NO: Closed Unit Has Shut Down Motors or Filters Require Service Immediately
See QUATRO System Control Panel & LED Diagnostic Table For More Info

30 Hymu
s
6- F
LED
If “S
e
If “S
e
Filte
r
A
cce
SPH
insta
l
befo
r
Insta
1
st
fil
t
2
nd
fil
Plac
e
crus
h
3
rd
fil
t
OPT
I
125.
the c
o
The
a
on t
h
Disp
o
and l
Odo
r
The
o
FOR
If the
Res
e
1
2
3
4
5
6
7
8
---------------
-
s
Boulevard, Mo
ILTER SE
R
Diagnostic
T
e
rvice Filter(s
e
rvice Filter(s
r
Access
ss to all the fi
&
A
F800 s
y
l
lation of ON
E
r
e running th
e
ll filters in the
t
er to be lowe
ter to be low
e
e
the Dust Fil
t
h
ed by the co
v
t
er to be low
e
I
ONAL filters:
The Dust Pa
d
o
ver as pictu
r
a
bove instr
u
h
e inside of t
o
sal of both
o
egal disposa
l
r
Filter Refilli
o
dor filter do
e
SYSTEMS
W
“Service Filt
e
e
tting “Servi
c
1
- Ensure fil
t
2
- Plug pow
e
3
- Press & h
4
- Hold for 1
5
- You are n
6
- Press SP
E
7
- Press &
H
8
- Release,
w
-
----------------
-
ntreal, Quebec,
R
VICE & R
T
able - “Ser
v
)” alert is FL
A
)” alert is ON
lters are thro
u
y
stems have
E
bank of filte
r
e
system.
following se
q
red into the L
A
e
red into plac
e
t
er Support F
v
er and poor
s
e
red into plac
e
Your filter s
e
d
gets place
d
r
ed above.
u
ctions are f
o
h
e access d
o
o
dor and parti
l
of spent filt
e
ng
s not have to
W
ITH iSERIE
S
e
rs” LED doe
s
c
e Filter(s)”
t
er access d
o
e
r back to th
e
old SPEED
U
0+ seconds,
ow in RESE
T
E
ED DN (2 T
H
OLD POWE
R
w
hen LED st
o
-
-----------------
H9R 1C9 Tel.
EPLACE
M
v
ice Filter(s)
”
A
SHING SLO
W
SOLID repla
c
u
gh the top c
o
2 identical b
r
s and must b
q
uence:
A
SER BLUE
e
is the HEP
A
rame with th
e
s
ystem perfo
r
e
is the Dust
F
e
quence may
d
on top of th
e
o
r the most
p
o
or. This filt
e
culate filters
i
e
rs.
be replaced.
S
CONTROL
S
s
not go out o
n
A
lert
o
or is closed
e
unit
U
P & DN sim
u
when panel i
s
T
MENU, in t
h
imes) until “
S
R
button whil
e
o
ps FLASHI
N
----------
W
e
M
: (514) 630-444
4
M
ENT
”
Alerts (iSe
r
W
LY some o
f
c
e the odor fi
o
ver.
anks of filter
e repeated f
o
GEL (or onto
A
filter. Part #:
e
gasket faci
n
r
mance.
F
ilter Part # :
F
include a Du
s
e
dust filter j
u
p
opular filte
r
e
r sequence
c
i
s the respon
s
It can be refil
S
:
n
its own afte
u
ltaneously u
n
s
beeping co
n
h
is condition,
S
ervice Filte
r
e
“Service F
N
G & stops B
E
Laser
B
Gel
Filter Top
A
ccess Cove
r
Optional Pre-Fi
l
Knock Out Pad
PN: F166-125
STAGE 1
M
ake Clean
A
4
Fax: (514) 63
0
r
ies Control
s
f
the particul
a
lter.
s installed b
e
o
r the second
gasket) is th
e
F074
n
g down. Fail
u
F
071
s
t Pad PN: F
0
u
st before ins
t
r
sequence.
F
c
an be cust
o
s
ibility of the
e
led with new
f
r changing th
e
n
til unit BEE
P
n
tinuously, r
e
“System ON
”
r
(s)” LED is
F
ilter(s)” LED
E
EPING
B
lue
l
ter
A
i
r
-----------
-
0
-4454 websit
e
s
)
a
te filters are
e
side each
o
bank. ALWA
Y
e
chemical filt
e
u
re to install
t
0
69-220 (Not
t
alling the co
v
F
or all other
o
mized for y
o
end user. Pl
e
f
iltration medi
e
filters follo
w
P
S
e
lease button
s
”
Led is FLA
S
F
LASHING
D
is FLASHIN
G
-
----------------
-
e
: www.QUATR
O
getting clogg
o
ther. The in
s
Y
S make sur
e
e
r. Part #: A
G
t
he frame will
t
Pictured) or
v
er. The Kno
c
r
filter seque
n
o
ur applicati
o
e
ase contact
l
a.
w
the reset pr
o
s
S
HING QUIC
K
G
& unit is B
E
Q
-
-----------------
O
-air.com info
@
ed and need
s
tructions be
l
e
all of the filt
e
G
097.
result in the
a Knock Out
c
k Out Pad g
n
ces follow
t
o
n.
l
ocal authoriti
o
cedure belo
w
K
LY
E
EPING cont
D
S
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
to replaced.
l
ow are for t
h
e
rs are install
e
dus
t
filter bei
n
Pad PN: F1
6
ets installed
o
t
he filter ord
es for prope
r
w
.
inuously
D
ust Filter
S
upport Frame
Dust Filter
PN: F071
STAGE 2
HEPA Filter
PN: F074
STAGE 3
Odor Filter
PN: AG097
STAGE 4
Optional Pre-Fi
Knock Out Pad
PN: F166-125
STAGE 1
O
I
nc.
m
h
e
e
d
n
g
6
6-
o
n
er
l
ter

30 Hymu
s
Repl
a
Qt
y
1
1
1
1
1
1
1
1
1
1
The
Q
gene
befo
r
Gen
e
S
t
7-
M
LED
If “S
e
MO
T
W
AR
The
m
REM
“Quick
Dete
ONL
Y
IMP
O
hour
s
Plea
s
The
y
In so
high
“Infi
n
Be
D
---------------
-
s
Boulevard, Mo
a
cement Filte
r
y
O
d
Q
uatro Syste
m
ral filter sequ
r
e ordering.
e
ral Filter M
a
t
age
1 Du
s
2
3
4
M
OTOR SE
Diagnostic
T
e
rvice Filter(s
T
OR ACCES
S
R
NING: Swit
c
m
otor(s) are
a
OVE ALL FI
L
Change” Brush M
o
rmine which
t
Y
the “Quick
O
RTANT NO
T
s
of daily ope
s
e note this i
s
y
are designe
d
me extreme
c
pressure (dir
t
n
ity” & Brushl
D
EFECTIVE
W
-
----------------
-
ntreal, Quebec,
r
Part Numbe
r
D
Optional Pre
Optional Pre
F
Optional Knoc
Optional Knoc
Dust
HEPA
F
d
or Filter (Most
Odor Filter
R
Gel Rep
a
Filter
G
m
can be eq
u
ence that wo
a
intainence
G
Filter
s
t Or KO Pad
Dust
HEPA
Odor
R
VICE &
R
T
able - “Ser
v
)” alert is ON
S
c
h unit off and
a
ccessed thr
o
L
TERS BEFO
o
to
r
t
ype of motor
C
hange” Mo
t
T
E FOR UNI
T
ration), the b
r
s
NOT consid
d
to operate
2
c
ases motor l
t
y filters) for
e
ess Motors
A
W
ithin The W
a
Quick Ch
a
Brush
-
-----------------
H9R 1C9 Tel.
r
s
D
escription
Filter Pad Kit
(
F
ilter Pad Kit (
1
k Out Pad Kit
(
k Out Pad Kit
(
Filter (6 Pack)
F
ilter (2 Requir
e
Applications)
(
R
efill Kit (2 Re
q
a
ir/Replaceme
n
G
asket (40’ Ro
l
u
ipped with
m
rk in most a
p
G
uide:
Reccomen
d
E
E
Ev
Ev
R
EPLACE
M
v
ice Motor(s
)
SOLID the
m
unplug pow
e
ugh the botto
RE TURNIN
G
“Infi
n
your system
or Brushes c
a
T
S EQUIPP
E
r
ushes on th
e
ered a warra
2
000-3000 h
o
ife can even
e
xtended peri
A
re Consider
e
a
rranty Perio
d
a
nge
Motor Ac
c
Panel
----------
W
e
M
: (514) 630-444
4
(
6 Pack)
1
2 Pack)
(
12 Pack)
(
25 Pack)
e
d)
(
2 Required)
q
uired)
n
t Kit
l
l)
m
any filter se
q
p
plications. V
e
d
ed Filter Chang
e
E
very 3 Months
E
very 6 Months
ery 6-18 Month
s
ery 6-18 Month
s
M
ENT
)
” Alerts
m
otor(s) need
e
r cord from
w
m access pa
n
G
THE UNIT
O
n
it
y
” Brush Motor
has installed
a
n be replac
e
D WITH “IN
F
e
INFINITY M
nty issue. M
o
o
urs and then
be less than
2
ods of time.
e
d Consuma
b
d
.
c
ess
M
ake Clean
A
4
Fax: (514) 63
0
P
a
F0
F
0
A
A
F
0
F
A
A
A
H
q
uences. The
e
rify the filter(
e
Interval
s
s
to be servic
e
w
all before ser
v
n
e.
O
VER TO AC
and follow t
h
e
d in the field
F
INITY” MO
T
otors may w
e
o
tor life is a fu
replaced.
2
000 hours
a
b
les And Will
N
Infinity Cu
r
Motor Bru
s
A
i
r
-----------
-
0
-4454 websit
e
a
rt No.
69-220
0
69-71
A
G168
A
G169
0
71-BX
F
074
A
G097
A
G119
A
R020
H
296
filters shown
s) in your Q
u
iSeries Cont
r
Non
e
Non
e
“Service Filter
s
“Service Filt
e
e
d or replace
d
v
icing the mo
C
CESS THE
M
B
h
e service or
(motor brus
h
T
ORS: In cas
e
e
ar before th
e
u
nction of ho
u
a
nd this is us
u
N
ot Be Chan
g
r
ved
s
h
-
----------------
-
e
: www.QUATR
O
Filter Stage
Stage 1
Stage 1
Stage 1
Stage 1
Stage 2
Stage 3
Stage 4
Stage 4
N/A
N/A
n
on the abov
e
u
atro System
r
ol Panel
e
e
s
” Flashing
e
rs” ON
d
.
o
tor(s).
M
OTORS.
rushless Moto
r
replacement
h
es can be re
e
s of heavy
p
e
warranty is
u
rs used and
f
u
ally due to t
h
g
ed Under
W
Q
-
-----------------
O
-air.com info
@
e
table are t
h
for the corre
c
instructions.
placed).
p
roduction (c
o
over.
f
ilter mainten
a
h
e system be
i
W
arranty Unle
s
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
h
e most popu
l
c
t part numb
e
o
ntinuous
a
nce.
i
ng run at a
s
s Found To
O
I
nc.
m
l
ar
e
rs

30 Hymu
s
Serv
Eve
n
exce
s
The
b
The
f
Y
OU
Fig 1:
Repl
A
LL
O
1- U
n
2- U
s
3- Li
f
4- R
e
scre
w
5- Cl
o
6- F
o
mi
n
lo
n
F
o
T
h
1
2
3
4
5
6
7
8
A
m
Br
u
For
u
time
---------------
-
s
Boulevard, Mo
ice- Motors
W
n
with replace
s
sively or co
n
b
rushes on
t
f
ollowing ima
g
DO NOT H
A
Motor Brushes
acement In
s
O
W MOTOR(
S
n
plug power
c
s
ing a phillips
f
t the gold col
o
e
place both
m
w
s.
o
se motor ac
c
o
r units with
nimum spee
d
n
ger motor lif
e
o
r units with
i
h
is MUST be
d
1
- Ensure fil
t
2
- Plug pow
e
3
- Press & h
4
- Hold for 1
5
- You are n
6
- Press SP
E
7
- Press &
H
8
- Release,
w
A
fter resettin
g
m
otor(s) at lo
w
u
shes Per Pac
k
6-Pack
u
nits equipp
e
so the brush
-
----------------
-
ntreal, Quebec,
W
ith “Quick
able motor b
r
n
suming brus
t
he SPH Or
A
g
es are for ill
u
A
VE TO REM
O
s
tructions
S
) TO COOL
c
ord and rem
o
screwdriver,
u
o
red tab and l
m
otor brushes
c
ess panel.
‘Basic” Con
d
. This is a br
e
e
.
i
Series Cont
r
d
one EVEN I
t
er access d
o
e
r back to th
e
old SPEED
U
0+ seconds,
ow in RESE
T
E
ED DN (1 T
H
OLD POWE
R
w
hen LED st
o
g
the “Servic
e
w
speed for
2
k
age Mot
o
e
d with 2 O
R
wear rates s
t
-
-----------------
H9R 1C9 Tel.
Change” B
r
r
ushes the “
Q
hes too quic
k
A
F system c
a
u
stration pur
p
O
VE TURBI
N
Fig
2
FOR 45 MIN
S
o
ve motor ac
c
u
nscrew the
2
ift/pull out ea
c
making sure
t
trols, plug in
e
ak in period
f
r
ols, Reset “
F L2 IS NOT
o
or is closed
e
unit
U
P & DN sim
u
when panel i
s
T
MENU, in t
h
ime) until “S
e
R
button whil
e
o
ps FLASHI
N
e
Motor(s)” Al
e
2
0 minutes to
o
rSafe Brush P
a
AB117
R
3 motors: I
t
t
ay in sync.
----------
W
e
M
: (514) 630-444
4
r
ushes
Q
uick Change
k
ly they shoul
a
n be chang
e
p
oses only.
E FROM UN
I
2
: 1 Motor Brush
S
BEFORE S
c
ess panel.
2
screws hold
c
h brush (Fig
t
he locking ta
power cord
a
f
or the brush
e
Service Mot
o
ILLUMINAT
E
u
ltaneously u
n
s
beeping co
n
h
is condition,
e
rvice Moto
r
e
“Service
M
N
G & stops B
E
e
rt, the moto
r
properly bre
a
a
rt #
t
is highly re
c
M
ake Clean
A
4
Fax: (514) 63
0
” motors do
h
d be replace
d
e
d in less th
I
T TO CHAN
G
Removed
ERVICING
ing down ea
c
2)
b on the brus
a
nd run the u
n
e
s and is requ
o
r(s) Alert.
E
Dor the mo
t
n
til unit BEE
P
n
tinuously, r
e
“System ON
”
(s)” LED is
F
M
otor(s)” LE
D
E
EPING
r
(s) will defau
a
k the new b
r
c
ommended t
o
A
i
r
-----------
-
0
-4454 websit
e
h
ave a servic
e
d
.
an 5 minute
s
G
E BRUSHE
S
F
c
h of the 2 gol
h is facing th
e
n
it with the h
o
ired to prope
r
t
or(s) replace
P
S
e
lease button
s
”
Led is FLA
S
F
LASHING
D
is FLASHI
N
u
lt to low spe
e
r
ushes in.
o
replace all
m
-
----------------
-
e
: www.QUATR
O
e
life. When t
s
with the u
s
S
!
F
ig 3: New Motor
d colored bru
e
motor and r
e
o
se disconne
c
r
ly seat the b
r
ment alert wi
s
S
HING QUIC
K
N
G & unit is
B
e
d. It is reco
m
m
otors or all
s
Q
-
-----------------
O
-air.com info
@
he motor(s)
a
s
e of a scre
w
Brush
sh casings (
F
e
-install the r
e
c
ted for 20 mi
n
r
ushes and to
ll not functio
n
K
LY
B
EEPING con
m
mended to
o
s
ets of brush
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
a
re sparking
w
driver.
F
ig 1).
e
taining
n
utes at
promote
n
correctly.
tinuously
o
perate the
es at the sa
m
O
I
nc.
m
m
e

30 Hymu
s
Repl
A
LL
O
1- U
n
2- Di
s
3- R
e
4- R
e
5- In
s
T
H
re
s
c
u
Figu
r
6- In
s
7- Pl
u
m
o
1
2
3
4
5
6
7
8
2
3
2
3
AL
W
wea
r
8- T
Sy
m
Uni
t
Mo
t
Ins
u
Ex
c
Ex
c
For
u
---------------
-
s
Boulevard, Mo
acement In
s
O
W MOTOR(
S
n
plug power
c
s
connect wir
e
e
move the re
t
e
move the m
o
s
tall the brac
k
H
IS IS PARTI
s
ult in a sho
u
tout as per
F
r
e1: “Quick C
s
tall the asse
u
g in power
c
o
tor(s) replac
e
1
- Ensure fil
t
2
- Plug pow
e
3
- Press & h
4
- Hold for 1
5
- You are n
6
- Press SP
E
7
- Press &
H
8
- Release,
w
R
230V “
Q
230
V
3
0V Brushles
s
30V Brushle
s
W
AYS replac
e
r
in sync.
ROUBLE
S
m
ptoms
t
will not start
t
or shuts off
u
fficient airflo
w
c
essive airflo
w
c
essive noise
u
nits equipp
e
-
----------------
-
ntreal, Quebec,
s
tructions
S
) TO COOL
c
ord and ope
n
e
s, cut zip tie
s
t
aining nuts
&
o
tor retaining
k
et on the ne
w
CULARLY I
M
rt to ground
F
igure 2.
hange” Moto
r
mbly back in
t
c
ord and Res
e
e
ment alert
w
t
er access d
o
e
r back to th
e
old SPEED
U
0+ seconds,
ow in RESE
T
E
ED DN (1 T
H
OLD POWE
R
w
hen LED st
o
R
eplacemen
Q
uick Change
”
V
“Infinity” (S
P
s
(SPH & AF
8
s
s (SPH &
AF
e
all motors
S
HOOTING
Possibl
Fault
y
Circui
t
Motor
/
Motor
Motor
/
w
Obstr
u
Clogg
e
w
Filter(
s
Motor
Motor
e
d with iSer
i
-
-----------------
H9R 1C9 Tel.
FOR 45 MIN
S
n
motor acces
s
.
&
lock washe
r
bracket from
w
motor. See
M
PORTANT
F
for the bru
s
r
Figur
e
t
o the unit &
c
e
t “Service
M
w
ill not functi
o
o
or is closed
e
unit
U
P & DN sim
u
when panel i
s
T
MENU, in t
h
ime) until “S
e
R
button whil
e
o
ps FLASHI
N
t Motors
”
(SPH & AF
8
P
H & AF835L
8
2B5 “iSerie
s
F
82B5 “Basic
”
at the same
GUIDE
e Cause
power suppl
y
t
breaker trip
p
/
motor brush
e
overheated,
t
/
motor brush
e
u
ction in syst
e
e
d filter (s)
s
) not in plac
e
impeller con
t
bearing failu
r
i
es Controls
----------
W
e
M
: (514) 630-444
4
S
BEFORE S
s panel.
r
holding the
m
the old mot
o
the installati
o
F
OR “INFINI
T
h contactin
g
e
2” “Infinity”
M
c
onnect the
w
M
otor(s)
A
le
r
o
n correctly.
F
u
ltaneously u
n
s
beeping co
n
h
is condition,
e
rvice Moto
r
e
“Service
M
N
G & stops B
E
8
35)
)
s
” Controls)
”
Controls)
time in a sy
s
y
p
ed
e
s past servi
c
t
ripped on th
e
e
s past servi
c
e
m
e
t
acting housi
n
r
e
see the ‘Lig
M
ake Clean
A
4
Fax: (514) 63
0
ERVICING
m
otor assem
b
o
r. Note the o
r
o
ns pictures
b
T
Y” MOTOR
S
g
the bracke
t
M
otor
w
ires. Install n
r
t. This MUS
T
F
ollow the ins
t
n
til unit BEE
P
n
tinuously, r
e
“System ON
”
(s)” LED is F
M
otor(s) LED
E
EPING
Part #
AB002
AR176
AB045-2
5
AB040-2
5
s
tem equip
p
c
e life
e
rmal cutout
c
e life
n
g
ht Diagnosti
A
i
r
-----------
-
0
-4454 websit
e
b
lies.
r
ientation on
t
b
elow.
S. If the bra
c
t
. The curve
d
ew zip ties.
T
be done E
V
t
ructions bel
o
P
S
e
lease button
s
”
Led is FLA
S
LASHING
is FLASHIN
G
5
5
p
ed with mor
Suggeste
d

Check
b
RESET
Replac
e

Switch
p
replace
Replac
e

Remov
e
Replac
e

Install fi

Replac
e
Replac
e
cs Table” fo
Infinity Curved
Moto
r
Brush
-
----------------
-
e
: www.QUATR
O
t
he bracket.
c
ket is instal
d
brush mu
s
Figure 3: Br
u
V
EN IF L2 IS
N
o
w.
s
S
HING QUIC
K
G
& unit is B
E
r
e than 1 bru
s
d
Solution
b
reaker box/
p
circuit break
e
e
motor/moto
r
p
ower off, un
p
filters/verify
b
e
motor/moto
r
e
obstruction
e
filter (s)
lter(s)
e
motor
e
motor
o
r additional
Q
-
-----------------
O
-air.com info
@
led incorrec
t
s
t be visible
i
u
shless
N
OT ILLUMI
N
K
LY
E
EPING conti
s
h motor to
p
ower conne
c
e
r on unit pa
n
r
brushes
p
lug, wait till
m
b
lockage.
r
brushes
troublesho
o
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
t
ly it may
i
n the large
N
ATED or th
e
nuously
keep brush
c
tion
n
el
m
otor cools,
o
ting.
O
I
nc.
m
e

QUATRO
Air Technologies Inc.
------------------------------------------------------------ We Make Clean Air ----------------------------------------------------------
30 Hymus Boulevard, Montreal, Quebec, H9R 1C9 Tel.: [phone] Fax: [phone] website: www.QUATRO-air.com i[email protected]
9- SPECIFICATIONS
Nominal Airflow (Triple Motor) 330 CFM
Nominal Airflow (Double Brushless Motor) 560 CFM
Approximate Dimensions: 30.5" (775mm) High x 15.75" (400mm) Wide x 25" (635mm) Deep
Voltage/Phase/Frequency, Current, Power Triple Brush Type 230/1/50, 12 amps, 2760 Watts (Operating at 60Hz)
Double Brushless 230/1/50: 12 amps 2300 Watts (Operating at 60Hz)
Approx. Weight: 140lbs (54kg) w/o filters
200lbs (91kg) with filters
10- GENERAL REPLACMENT PARTS
Qty Description Part
1 Power Cord 230v E519
1 Power Cord (Euro 230V) E130
1 Remote Cable AE427
1 Cover Gasket Roll (40') H006
11- WARRANTY
QUATRO Air Technologies warrants its equipment to be free from defect in material and workmanship under normal use
and service for a period of one year from date of shipment. QUATRO's obligation under this warranty shall be limited to
replacing any parts, thereof, which shall be demonstrated to have been defective. This is expressly in lieu of all other
warranties, express or implied, including the warranties of merchantability and fitness.
QUATRO claims no warranty as to merchantability or as to the fitness of the merchandise for any particular use and shall
not be liable for any loss or damage. No person, firm or corporation is authorised to assume for QUATRO any other liability
in connection with the sale of these goods. Equipment, parts and material manufactured by others and incorporated in
QUATRO's equipment are warranted by QUATRO only to the extent of the original manufacturer's liability to QUATRO Air
Technologies Inc.
Conditions and Limitations:
This warranty does not cover abuse, misuse, maintenance negligence, improper assembly, acts of vandalism, acts of
God, fear wear, modifications of the equipment or installation of a part not recommended by QUATRO Air Technologies, as
well as operation of the equipment at voltages other than those specified by QUATRO Air Technologies Inc.
IMPORTANT NOTE FOR UNITS EQUIPPED WITH “INFINITY” MOTORS: In cases of heavy production (continuous
hours of daily operation), the brushes on the INFINITY Motors may wear before the warranty is over.
Please note this is NOT considered a warranty issue. Motor life is a function of hours used and filter maintenance.
They are designed to operate 2000-3000 hours and then replaced.
In some extreme cases motor life can even be less than 2000 hours and this is usually due to the system being run at a
high pressure (dirty filters) for extended periods of time.
Warning:
ThisisaclassAproduct.Indomesticenvironment,thisproductmaycauseradiointerferenceinwhichcasetheusermaybe
requiredtotakeadequatemeasures.
For Technical Assistance, call QUATRO Air Technologies inc. at
[phone] (in Montreal, Canada).
Please ensure that you have your equipment serial number available when calling.

30 Hymu
s
---------------
-
s
Boulevard, Mo
-
----------------
-
ntreal, Quebec,
-
-----------------
H9R 1C9 Tel.
----------
W
e
M
: (514) 630-444
4
M
ake Clean
A
4
Fax: (514) 63
0
A
i
r
-----------
-
0
-4454 websit
e
-
----------------
-
e
: www.QUATR
O
Q
-
-----------------
O
-air.com info
@
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
O
I
nc.
m

30 Hymu
s
---------------
-
s
Boulevard, Mo
-
----------------
-
ntreal, Quebec,
-
-----------------
H9R 1C9 Tel.
----------
W
e
M
: (514) 630-444
4
M
ake Clean
A
4
Fax: (514) 63
0
A
i
r
-----------
-
0
-4454 websit
e
-
----------------
-
e
: www.QUATR
O
Q
-
-----------------
O
-air.com info
@
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
O
I
nc.
m

30 Hymu
s
---------------
-
s
Boulevard, Mo
-
----------------
-
ntreal, Quebec,
-
-----------------
H9R 1C9 Tel.
----------
W
e
M
: (514) 630-444
4
M
ake Clean
A
4
Fax: (514) 63
0
A
i
r
-----------
-
0
-4454 websit
e
-
----------------
-
e
: www.QUATR
O
Q
-
-----------------
O
-air.com info
@
Q
UATR
O
Air Technologies
------------
@
QUATRO-air.c
o
O
I
nc.
m