Quickie Hula User manual

Instructions for Use
Hula
Powered Wheelchair
21417002

2HULA Rev.1.0
IMPORTANT:
DO NOT USE YOUR Wheelchair UNTIL
THIS MANUAL HAS BEEN READ AND
UNDERSTOOD.
User Information
Intended use power wheel wheelchairs:
This power wheelchair was designed for persons
whose ability to walk is impaired but who have sufficient
eyesight and have the physical and mental attributes to
be able to operate an electric wheelchair safely. It has
been classified according to EN 12184 as a class A
mobility product (indoor use).
The Quickie HULA powered wheelchair has been
designed for indoor use, however the Hula can be used
outdoors provided its use remains within the stated
criteria:
The Hula can be used on slopes/ramps where the
gradient or slope does not exceed 6 degrees (1 in 10
slope). Ramps and slopes for many buildings have a
slope of 1 in 12 (5 degrees)
The Hula can be used to climb kerbs or obstacles to
a maximum height of 50mm (2”). Most door threshold
steps will be less than 50mm.
It is important the user does not attempt to use the
wheelchair in the home environment where the slopes/
gradient are greater than 6 degrees or steps that are
greater than 50mm.
Please refer to the technical specification
(section 13), of this manual for further
information.
Area of application
The variety of fitting variants as well as the modular
design mean that it can be used by those persons who
are mentally and physically able to control an input
device to operate the wheelchair and its functions in a
safe way, but cannot walk or have limited mobility e.g.
because of:
Paralysis•
Loss of extremity (leg amputation)•
Extremity defect deformity•
Joint injuries•
Strokes and brain injuries•
Neurological disabilities (e.g. MS, Parkinson…)•
Illnesses such as heart and circulation deficiencies,•
disturbance of equilibrium or cachexia as well as
for elderly people who still have the strength in the
upper body.
Sunrise Medical declares under its sole responsibility
that this product is in conformity with the requirements of
the directive 93/42/EEC amended by 2007/47/EEC.”
Sunrise Medical declaresthatthisproductfullsthe
Performance requirements of ISO 7176-19 - Wheeled
mobility devices for use as a seat in a motor vehicle;
(known as the Crash Test).
When considering provision, please also note the body
size, weight including the distribution of body weight, the
user’s physical and psychological constitution, the age of
the user, their living conditions and their environment.
If in doubt a health care professional should be involved
to ensure the user is not exposed to unacceptable risks.
Sunrise Medical has a quality management system that
is certified to ISO 9001:2008, that covers all stages
of development, production and manufacture of this
wheelchair.

HULA 3
Rev.1.0
1.0 Your Wheelchair 5
2.0 How to use this manual 5
2.1 Introduction 5
2.2 Guarantee 5
2.3 Warranty conditions 5
3.0 Label Explanation / Word definitions 6
3.1 Definitions of words used in this manual 6
3.2 Label explanations 7
4.0 General safety warning and user tips 8
4.1 General warnings 8
4.2 Features and options 8
4.3 Obstacles 8
4.4 Routine service 8
4.5 Brake release 8
4.6 EMC - Radio transmitting devices. 9
4.7 Emergency braking 9
4.8 Sharp turns 9
4.9 Batteries 9
4.10 Tyres 9
4.11 Weight limit 10
4.12 Wheelchair motors 10
4.13 Hot surfaces 10
4.14 Wheelchair range 10
4.15 Outdoor use (Fig.4.3) 10
4.16 Adverse conditions 11
4.17 Ramps 11
4.18 Transfer to and from the wheelchair 11
4.19 Use on a slope 12
4.20 Using a vehicle mounted passenger lift 12
4.21 Stability of your wheelchair 13
4.22 Wheels & Tyres 13
4.23 Swing away tray 13
4.24 Anterior Pelvic Support 15
4.25 VR2 Controller (Fig. 4.14) 16
5.0 Preparing your wheelchair for use 16
5.1 Handling the wheelchair 16
5.2 Preparation for every day storage 16
5.3 Re-Assembling 17
5.4 Brake release (Fig.5.7 - 5.9) 17
5.5 Control pod joystick unit position 18
5.6 Getting ready to drive 18
5.7 Armrests 19
5.8 Leg Rests 24
6.0 Seating 26
6.1 Firm seat board 26
6.2 Seat cushions 26
6.3 Removable seat covers 26
6.4 Backrest upholstery 26
6.5 JAY backrests 26
6.6 Seat width adjustment 26
6.7 Seat height adjustment/removal 27
6.8 Standard Seat Depth Adjustment 28
6.9 Backrest Angle Adjustment -4° to +12° 28
6.10 Back Height Adjustment 29
6.11 Mechanical Seat Tilt 31
6.12 Centre Of Gravity (COG). 31
6.13 JAY backrests 32
6.14 Headrest 32
7.0 Control System 32
7.1 VR2 control system information (Fig.7.1) 32
7.2 VR2 Dual control unit (Optional) 34
8.0 Troubleshooting using the VR2
Hand Control 36
9.0 Controller Mounts 38
9.1 General warnings: 38
9.2 Attendant control (Optional): 38
9.3 Parallel swing-away control: 38
10.0 Batteries and charging 39
10.1 Batteries (Fig.10.1-10.6) 39
10.2 Safety cut-outs (Fuses) 40
10.3 General battery information 40
10.4 Maintenance free batteries 40
10.5 Battery care 40
10.6 Maintenance free battery care plan 40
10.7 General charger information 41
10.8 Charger safety features 41
10.9 Connecting the charger and charging 41
10.10 Charger safety and caution notes 41
10.11 The range of your vehicle 42
10.12 Battery warranty 42
11.0 Transportation 43
11.1 Transportation warnings: 43
11.2 Occupant restraint instructions 44
11.3 Special shipping requirements: 44
11.4 Crash testing on the Hula. 45
11.5 The tie down label and strap placement 45
11.6 Securing the wheelchair into the vehicle 46
12.0 Maintenance and Cleaning 46
12.1 Tyre wear 46
12.2 Drive wheel replacement 46
12.3 Castor wheel replacement 47
12.4 Cleaning your wheelchair 48
12.5 Inspection of the upholstery/seating 48
12.6 Cleaning seating 48
12.7 Cleaning controls 49
12.8 Electrical connections 49
12.9 Main Controller access 49
12.10 Shipping & Storage Requirements: 50
12.11 Authorised Sunrise Medical service agents 50
12.12 Recommended maintenance routines 51
12.13 Performance checks 52
13.0 Specification sheets 53
14.0 Service History 54
15.0 Disposal/ Recycling 55

4HULA Rev.1.0
Side Guard
Backrest
Batteries
Armrest
Legrest
Controller
Cushion
Castor
Footplate
Drive wheel
HULA
Service Agent Details:
Wheelchair Serial Number:

HULA 5
Rev.1.0
1.0 Your Wheelchair
We at Sunrise Medical want you to get the best out of
your Hula wheelchair. This Owner’s Manual will familiarise
you with the wheelchair and its features. It contains
hints on everyday usage and general care in addition to
information on the high quality standards which we adhere
to and details about the guarantee.
Your wheelchair should be delivered fully configured for
your use; there are a wide range of components and
adjustments available on the Hula. For further information
about these you should contact your Sunrise Medical
authorised dealer.
Your wheelchair will reach you in excellent condition
having been personally inspected before leaving our
factory. Following the guidelines for maintenance and
cleaning your wheelchair will maintain its first class
condition and give you complete satisfaction.
The Hula has been designed for use by an individual on a
daily basis.
This wheelchair has been designed for a single occupant
of limited mobility up to the weight of 136Kg.
The end user must have the cognitive, physical and visual
ability to control the vehicle safely on a maximum slope of
6°.
If you are in any doubt as to the suitability of the power
wheelchair, contact your local Sunrise Medical authorised
dealer or health care provider for clarification, prior to
commencing use.
It is very important to read the relevant section of the
owner’s manual when making any minor adjustments.
Complicated adjustments should only be carried out by
your heath care provider or authorised Sunrise Medical
dealer
If you have any queries about the use, maintenance
or safety of your wheelchair, please contact your local
authorised Sunrise Medical dealer. If you do not know
of an approved dealer in your area or have any other
questions please write or telephone:
Sunrise Medical
Thorns Road
Brierley Hill
West Midlands
DY5 2LD
Phone: [phone]
Fax: [phone]
www.SunriseMedical.com
2.0 How to use this manual
2.1 Introduction
Please keep a note of your local service agent’s address
and telephone number and your wheelchair serial number
in the space on the previous page.
In the event of a breakdown, contact them and try to give
all relevant details so they can help you quickly.
The wheelchairs shown and described in this manual
may not be exactly the same in every detail as your own
model. However, all instructions are still entirely relevant,
irrespective of detail differences.
NOTE: The manufacturer reserves the right to alter
without notice any weights, measurements or other
technical data shown in this manual. All figures,
measurements and capacities shown in this manual are
approximate and do not constitute specifications.
2.2 Guarantee
The guarantee form is included in the Sunrise Pack.
Please fill in the relevant details and return to us to
register your entitlement.
THIS IN NO WAY AFFECTS YOUR STATUTORY
RIGHTS.
2.3 Warranty conditions
1) The repair or replacement will be carried out by an
authorised Sunrise Medical dealer/service agent.
2) To apply the warranty conditions, should your
wheelchair require attention under these arrangements,
notify the designated Sunrise Medical service agent
immediately giving full information about the nature of
the difficulty. Should you be operating the wheelchair
away from the locality of the designated Sunrise Medical
service agent, work under the “Warranty Conditions” will
be carried out by any other service agent designated by
the manufacturer.
3) Should any part of the wheelchair require repair or
replacement, as a result of a specific manufacturing or
material defect, within twenty four months from the
date on which the possession of the wheelchair was
transferred to the original purchaser, and subject to it
remaining within that ownership, the part or parts will be
repaired or replaced completely free of charge if returned
to the authorised service agent.

6HULA Rev.1.0
4) Any repaired or replaced part will benefit from these
arrangements for the balance of the warranty period
applicable to the wheelchair.
5) Parts replaced after the original warranty has expired
are covered for a further twelve months.
6) Items of a consumable nature will not generally be
covered during the normal warranty period, unless such
items have clearly suffered undue wear as a direct result
of an original manufacturing defect. These items include
amongst others upholstery, tyres, inner tubes and
similar parts. On powered products this will also include
batteries, motor brushes, arm pads etc.
Batteries have a warranty period of 6 months for
manufacturing defects only.
7) The above warranty conditions apply to all wheelchair
parts for models purchased at full retail price.
8) Under normal circumstances, no responsibility will be
accepted where the wheelchair has required repair or
replacement as a direct result of:
a) The wheelchair or part not having been maintained
or serviced in accordance with the manufacturer’s
recommendations, as stated in the Owner’s Manual and/
or Service Manual. Or failing to use only the specified
original equipment parts.
b) The wheelchair or part having been damaged by
neglect, accident or improper use.
c) The wheelchair or part having been altered from the
manufacturer’s specifications, or repairs having been
attempted prior to the service agent being notified.
Life Expectancy
We estimate a life expectancy of 5 years for this product,
provided that:
It is used in strict accordance with the intended use•
as set out in this document.
All service and maintenance requirements are met.•
The estimated life expectancy can be exceeded if the
product is carefully used and properly maintained.
The life expectancy can also be considerably reduced by
extreme or incorrect usage.
The fact that we estimate a life expectancy for this
product does not constitute an additional warranty.
3.0 Label Explanation / Word definitions
3.1 Denitions of words used in this manual
Word Definition
DANGER!
Advice to the user of Potential Risk
of serious injury or death if the
advice is not followed
WARNING! Advice to the user of a potential risk
of injury if the advice is not followed
CAUTION! Advice to user that potential
damage to equipment may occur if
the advice is not followed
Possible finger pinch or trap hazard
NOTE: General advice or best practice
Reference To Additional
Documentation

HULA 7
Rev.1.0
3.2 Label explanations
Drive lever position for normal driving by the user.
Drive lever position for manoeuvring the wheelchair manually.
NOTE: The drive levers must be returned to the normal driving position
as soon as manual positioning is completed
Freewheel/Drive Information Label (Section 4.0)
The wheelchair is intended for indoor use. Outdoor use must be in
accordance with the advice given within this Owner’s Manual.
Indoor/Outdoor Information Label (Section 4.0)
Serial Number Label
Indicates the position of the wheelchair tie-down restraints.
Crash Test/ Tie Down Information Label (Section 11.0)
Electrical circuit diagram showing connections.
For use if the batteries require disconnecting.
Battery Wiring Label (Section 10.0)
Maximum Speed
Seat Depth
Maximum User Weight
Serial Number

8HULA Rev.1.0
4.0 General safety warning and user tips
4.1 General warnings
WARNING!
Always ensure that your wheelchair is switched off•
before attempting to transfer in or out.
Always ensure that you are able to operate all controls•
from a comfortable position. Paying attention to your
posture is essential to ensure your continued comfort
and well being.
Always make sure that you can be seen clearly,•
especially if you intend using your wheelchair in poor
light.
This wheelchair has been built to match the needs of•
a particular user. If used by another user then it may
need to be adjusted and reprogrammed.
Do not let children or others use your wheelchair.•
Be aware that the wheelchair may come to a sudden•
stop during operation. Sunrise Medical recommend
that the anterior pelvic support be worn at all times.
Do not operate the wheelchair if it is behaving•
abnormally or erratically.
4.2 Features and options
NOTE: Some of the options shown in this manual may
not be available in your country and may also restrict
the overall physical limits of the standard product (e.g.
max. speed, user weight limit, etc.). Those limitations are
marked on the order form, in the technical manual and
in this owner’s manual. For further information please
consult your Sunrise Medical authorised dealer.
4.3 Obstacles
DANGER!
Never descend a kerb backwards with a MWD•
wheelchair. Please read carefully the section 4.23.1
on kerb climbing in this manual before attempting to
mount and dismount any kerbs in your wheelchair.
Do not attempt to climb or descend a series of steps.•
It is unsafe to do so and could cause personal injury
or damage the wheelchair. The Hula has only been
designed to climb a single step or kerb.
We recommend that users with upper trunk instability•
wear further customised support systems to keep the
upright body position during descending or ascending
ramps, curbs or obstacles.
4.4 Routine service
The recommended service interval is one year. See
service history table, section 14.
WARNING!
This wheelchair is designed to be repaired and
assembled by a Sunrise Medical authorised dealer and
not the user. Information on disassembly and assembly
of the wheelchair for storage is shown in section 5.1-5.2.
4.5 Brake release
DANGER!
The Brake release, (freewheel), is only to be used in•
an emergency power breakdown situation e.g. Where
a large distance has to be covered to get the user
home or into a safe environment.
Brake release can also be used to manually•
manoeuvre the wheelchair to safety if a complete
and catastrophic loss of power such as control
system failure or battery failure has occurred.
Brake release should not be habitually used as a•
means of transporting the user as if in a manual
wheelchair.
When the power wheelchair is functioning normally,•
the brake release should only be used to park or
store the unoccupied wheelchair.
DANGER!
Please remember that you have no braking facility•
when the Brake release, (freewheel), levers are
moved from the normal drive position to the
freewheel position, Fig. 4.1, Fig 4.2,
Always ensure an attendant is with you when•
bringing the wheelchair into the freewheel mode.
The wheelchair must never be left with one or both•
levers in the freewheel position.
For an enhanced description of this facility and its
limitations to use, please see later section at 5.4.
Fig. 4.1 Fig. 4.2

HULA 9
Rev.1.0
4.9 Batteries
Your wheelchair is supplied as standard from Sunrise
Medical with maintenance-free batteries. These only
require regular charging. Before charging, please read
sections 10 and 12 in this manual.
WARNING!
Do not, under any circumstances, tamper with the
batteries. If in any doubt contact your local Sunrise
Medical authorised dealer.
CAUTION!
Before using your vehicle for the very first time, please
charge your batteries for a period of 24 hours.
WARNING!
All lead/acid batteries contain sulphuric acid.•
Avoid contact with acid on damaged sealed type•
batteries or wet batteries.
Battery acid can cause burns to the skin as well as•
damage to floors, furniture and your wheelchair.
If it comes into contact with the skin or clothing, wash•
immediately with soap and water.
If it comes into contact with the eye, immediately•
flood the eye with running cold water for at least 10
minutes and seek medical attention immediately.
Acid can be neutralised with baking soda and water.•
Take care to keep batteries upright at all times,
especially when transporting your wheelchair.
If you suspect that the batteries are damaged or•
leaking, contact your Sunrise Medical authorised
dealer immediately.
Only use the battery charger supplied with the•
wheelchair.
Only replace a faulty charger with one of the same•
type.
If you need a replacement battery charger, or are•
unsure about any of the above points, please contact
your authorised Sunrise Medical dealer.
Battery and charger connector type Hula:
24V (2x12V) / 36 Ah. Maintenance free
Dimensions Max: h=180 x w=195 x d=130 mm.
Charger Connector: Must be a 3 pin Neutrik connector.
4.10 Tyres
Your wheelchair tyres can wear depending on use.
Check them regularly in accordance with the service
instructions in this manual, (section 12.0).
4.6 EMC - Radio transmitting devices.
WARNING!
When operating two-way radio, walkie-talkies, C.B.,
amateur radio, public mobile radio and other powerful
transmitting devices the wheelchair should be brought to a
halt and turned off.
The operation of cordless, mobile telephones and cell
phones including hands-free devices is permitted but if
abnormal operation of the wheelchair is encountered then
the wheelchair must be brought immediately to a halt and
turned off.
NOTE: the electrical systems of the wheelchair may
disturb the performance of alarm systems in retail shops.
4.7 Emergency braking
There are three ways to stop your wheelchair:
1. Simplest and safest way to stop the wheelchair is to
release the joystick (see Hand Control section 7). This will
bring the wheelchair to a halt in a controlled manner.
2. Pulling back the joystick will brake the wheelchair abruptly
with a fast stop
3. Switching the control system off whilst the wheelchair is
in motion will also bring the wheelchair to a halt.
WARNING!
Switching the control system off is only to be used in an
emergency situation as the stopping action is very abrupt.
Sunrise Medical recommend the use of an anterior pelvic
support at all times.
4.8 Sharp turns
DANGER!
Full speed turns should not be attempted. If you need to
turn sharply you must reduce your speed with the joystick
or speed setting. This is particularly important when
travelling across or down a slope. Disregarding this advice
could lead to your wheelchair tipping over.

10 HULA Rev.1.0
4.11 Weight limit
DANGER!
The user plus items carried should never exceed a total
weight of 136Kg.
Never use this wheelchair for weight training if the total
weight (user plus additional weights) exceed a total weight
of 136Kg.
Exceeding the weight limit is likely to damage the seat,
frame or fasteners and may cause severe injury to you or
others from wheelchair failure
Exceeding the weight limit will void the warranty.
4.12 Wheelchair motors
After prolonged use, the motors will produce heat, which
is radiated through the motors’ outer casing.
WARNING!
Do not remove the protective shroud covering the motors
as the motors’ outer casing can remain hot for up to 30
minutes after using the wheelchair.
WARNING!
4.13 Hot surfaces
Not only the can the motors get hot during the operation
of the wheelchair, but also the upholstery material and
armrests can get hot when standing in direct sunlight on a
hot day.
WARNING!
Avoid Leaving the wheelchair standing in direct sunlight
for extended periods of time. The upholstery will get hot to
the touch.
4.14 Wheelchair range
The range of your wheelchair can be affected by many
factors such as user weight, terrain, ambient temperature,
use of powered options and battery condition.
NOTE: The stated range in the sales literature is for
comparison purposes with other wheelchairs and is a
theoretical maximum (ISO 7176; Part 4) and may not be
attained by every user (also see section 10.11 and section
13, in this manual).
We recommend that every user initially limit their journey
to half the stated range, until they have confidence in the
actual range their wheelchair can attain.
CAUTION!
If your battery indicator is showing a low charge then do
not attempt a long journey unless you are confident in
reaching your destination and also returning to your home
without the risk of being left stranded.
4.15 Outdoor use (Fig.4.3)
Please ensure that the limitations of the Hula
performance are understood before any outdoor
use, by reading this Owners’ Manual carefully.
If it is necessary to use the Hula outdoors, exercise
caution and show the utmost consideration for other
people.
Fig. 4.3
DANGER!
Remember that the last thing a car or lorry driver expects
to see is a wheelchair backing off the kerb into the road.
If in any doubt, do not risk crossing the road until you are
certain that it is safe. Always cross the road as quickly
as possible using a designated pedestrian crossing
whenever possible.

HULA 11
Rev.1.0
4.16 Adverse conditions
Please be aware that when driving your wheelchair in
adverse conditions, e.g. on wet grass, mud, ice, snow or
other slippery surfaces, you may experience a reduction
in the grip and traction of your wheelchair.
WARNING!
We recommend you take extra precautions in these•
conditions, particularly on hills and slopes; your
wheelchair could become unstable or skid causing
possible injury.
Take extra precautions when using your wheelchair•
during darkness or in poorly lit areas. Consideration
should be given to the use of high visibility markers or
reflectors, which can be fitted to the wheelchair.
Alternatively, use high visibility/reflective clothing•
such as fluorescent waistcoats, belts or armbands,
particularly in poorly lit areas or when crossing the
road.
DANGER!
When you are using a Powered Scooter or Wheelchair,
take extra care with loose or long items of clothing.
Moving parts, such as wheels, can be potentially
dangerous or even fatal if clothing becomes entangled.
NOTE: Extreme variances in temperature may trigger
the self protect mechanism in the control system. If this
occurs the control system will temporarily shut down to
prevent damage to the electronics or the wheelchair.
4.17 Ramps
WARNING!
When using a ramp, please ensure that it is capable of
taking the combined weight of the power wheelchair and
yourself. If a ramp is being used to load a wheelchair into
a vehicle, please ensure the ramp is properly secured to
the vehicle.
Always approach the ramp head-on and exercise caution.
CAUTION!
Please ensure your ramp is suitable for the product you
are transporting.
4.18 Transfer to and from the wheelchair
WARNING!
Sunrise Medical recommend that you consult your•
health care professional for assistance in developing
your personal front or side transfer technique to best
suit your needs and avoid any personal injury.
Ensure controller is switched off during transfers to•
avoid unintentional movement.
If a reclining arm rest is fitted, please ensure that•
the reclining support bar is secured into the recline
receiver that is attached to the seat frame.

12 HULA Rev.1.0
4.19 Use on a slope
Your wheelchair has been designed and tested to allow its
use on slopes or gradients of up to 6°. However, you have
the option of adjusting your seating position.
Please see warnings below.
WARNING!
In certain circumstances your wheelchair could become
unstable. Before attempting to climb or descend a slope
or a kerb, caution should be taken when using weight shift
options and/or using your body positioning for a counter
balance weight. To improve stability lean forward when
driving uphill, with the seat and back in an upright position.
Alternatively sit in an upright position when travelling in
a forward, downhill direction or tilt and/or recline the seat
backwards.
WARNING!
If you are in any doubt about the capabilities of your
wheelchair on a slope then do not attempt to drive up or
down the slope/kerb; try to find an alternative route.
4.19.1 Gradients: ascents
WARNING!
When going uphill, keep the wheelchair moving. Steer by
moving the joystick gently in the direction you wish to go.
If you have stopped going up hill, you should start slowly.
If necessary lean forward to prevent the tendency for the
front wheels to lift.
Please ensure that the limitations of the Hula
performance are understood before any outdoor
use, by reading this Owners’ Manual carefully.
4.19.2 Gradients: descents
WARNING!
On descents, it is important not to let the wheelchair
accelerate beyond its normal level of ground speed. In
fact, it is safer to proceed slowly down steep descents
(below the speed of 5kph) and stop, if any anxiety arises
regarding directional control. If the wheelchair picks up
speed, centre the control to slow it or to stop all forward
movement, then restart slowly and do not allow the speed
to increase.
NOTE: The solid state controller has the benefit of a logic
system that will help compensate when driving along a
camber or up a hill. This is an added safety feature on
your wheelchair. In addition of course, you may control the
wheelchair speed by using the speed control.
4.20 Using a vehicle mounted passenger lift
Wheelchair lifts are used in vans, buses and buildings to
help you move from one level to another.
DANGER!
Ensure that the user and all carers fully understand•
the lift manufacturer’s instructions for using the
passenger lift.
Never exceed the lift manufacturer’s recommended•
safe working load and load distribution guidance.
Always turn off all power when you are on the lift.•
If you fail to do so, you may touch the joystick by
accident and cause your wheelchair to drive off the
platform. Be aware that a rollstop at the end of the
platform may not prevent this.
Always position the user securely in the wheelchair to•
help avoid falls while on the lift.
Always ensure the wheelchair is in drive mode when•
using passenger lift (wheels locked not in freewheel
mode).

HULA 13
Rev.1.0
4.21 Stability of your wheelchair
Please follow the user instructions in this manual
regarding the use of your wheelchair on a slope.
WARNING!
Other variables can affect your wheelchair stability,
including:
Movement of the user.•
Effects of the addition of accessories or other•
equipment.
Inappropriate adjustments or modifications to the•
wheelchair.
In some cases these issues are further compounded by
the effects of the local environment such as:
Door thresholds Hills, Slopes, Ramps, Sloping•
pavements, Dropped kerbs.
Furthermore different body proportions of a wheelchair
user affect stability for example:
Lower limb wasting or amputation,•
Obesity•
Increased upper torso mass, Upper torso height•
4.22 Wheels & Tyres
WARNING!
Inspect all tyres before use for signs of wear.•
Ensure that there are no objects in your path that•
could possibly become lodged in your wheelchair
mechanism or in the hubs of the wheels. This could
cause the wheelchair to come to a sudden stop.
Riding over drains or grids could cause the wheelchair•
castors or wheels to become trapped, causing the
wheelchair to come to a sudden stop.
4.23 Swing away tray
WARNING!
The maximum weight the tray can hold is 2.5kg.•
Do not overload the tray, this could cause the tray•
to break or could cause the wheelchair to become
unstable.
Do not leave lit cigarettes or other heat sources on the•
tray as this could cause the tray to deform and mark.
Ensure that all extremities and clothing are free when•
positioning the tray for use.

14 HULA Rev.1.0
4.23.1 Mounting a low kerb or step
WARNING!
Approach the kerb at a 90° angle and stop the•
wheelchair as soon as the castor wheels touch the
kerb.
Apply sufficient power to the motors to lift the front•
of the wheelchair up onto the kerb (or step) and then
apply slightly more power and speed so that the drive
wheels climb the kerb (or step) smoothly and without
hesitation and the rear castor wheels come up as
well.
As far as possible, keep the joystick in the straight•
forward position, (Fig.4.4 - 4.6).
NOTE: In accordance to the ground clearance, the
maximum obstacle height possible to climb is 5.0 cm.
Please ensure that the limitations of the Hula
performance are understood before any outdoor
use, by reading this Owners’ Manual carefully.
Fig. 4.4
Fig. 4.5 Fig. 4.6
WARNINGS!
1. Please show the utmost consideration for the other
traffic on the road. Remember that the last thing a car or
lorry driver expects to see is a wheelchair backing off the
kerb into the road. If in any doubt, do not risk crossing the
road until you are certain that it is safe.
2. Always cross the road as quickly as possible; there may
be other traffic.
3. Do not attempt to go up or down more than a 5.0 cm
(2”) high kerb.
4. Do not attempt to climb a series of steps.
5. Do not attempt kerbs if on steep slopes or cambers.
6. Do not attempt any kerbs in the vicinity of drain covers,
uneven or gritty road surfaces.
7. You should not attempt to dismount a kerb any higher
than 5.0 cm (2”) in any direction.
8. Do not mount or dismount kerbs at an angle other than
straight on (90 degrees) to the edge of the kerb.
9. Prior to climbing ensure your legrests will clear the
kerb.
WARNING!
This wheelchair is designed to be repaired and assembled
by a Sunrise Medical authorised dealer and not the
user. Information on disassembly and assembly of the
wheelchair for storage is shown in section 5.1-5.2.

HULA 15
Rev.1.0
4.24 Anterior Pelvic Support
The Anterior Pelvic Support kit. (Fig. 4.7).
Fastening the anterior pelvic support:
Insert the 3 prong male buckle into the female buckle until
a click is heard (Fig. 4.8)
To fit the anterior pelvic support.
Place the strap loosely across the seat with the buckle•
closed.. (Fig. 4.9)
Pass the other ends of the strap through the gap•
between the backrest posts and the backrest
upholstery as shown. (Fig. 4.10)
Ensure that the adjusters & buckles can be accessed•
& the strap is not twisted. Fit the eyelets over the
rearmost bolts. Fit the plain washer, sprung washer &
nut. Tighten with a 13.0mm spanner. (Fig. 4.11)
Ensure that the anterior pelvic support is tight enough•
to provide comfortable support. A simple measure
is to keep a hands thickness between the body
andanterior pelvic support. For safety, check the
tension on the anterior pelvic support at least once
day. (Fig. 4.12)
Generally, the Anterior Pelvic Support should be fixed•
so that the straps sit at an angle of approximately 45°
(Fig. 4.13), and when correctly adjusted should not
allow the user to slip down in the seat.
WARNING!
Ensure that the Anterior Pelvic Support is secured•
and correctly adjusted before use.
An incorrectly fitted/adjusted Anterior Pelvic Support•
could allow the user to slip down, potentially causing
serious injury.
Inspect the Anterior Pelvic Support at regular intervals•
for any signs of fray or damage and replace as
necessary.
When servicing, check for correct operation of the•
release buckle and for any signs of wear on the
material or plastic brackets.
Fig. 4.8
Fig. 4.9
Fig. 4.10
Fig. 4.11
Fig. 4.12
Fig. 4.13
Fig. 4.7

16 HULA Rev.1.0
5.0 Preparing your wheelchair for use
5.1 Handling the wheelchair
NOTE: To dismantle the wheelchair for storage no tools
are required.
The following parts can be removed:
1 pair of swing-away legrests.
1 backrest.
1 drive unit with seat frame
5.2 Preparation for every day storage
Remove the swing-away legrests, (Fig.5.0).•
Leave the armrests in the fold down position. (Fig.5.1).•
Remove the Backrest by undoing the two lever screws•
at the base of the Backrest, (Fig.5.2).
Lay the backrest on the seat or store it separately,•
(Fig.5.3).
Now you can store the wheelchair.
NOTE: For long term storage, please see section 12.10.
Fig. 5.1
Fig. 5.0
Fig. 5.3
Fig. 5.2
4.25 VR2 Controller (Fig. 4.14)
Battery Level Indicator On/Off Button
Horn
Speed
Indicator
Speed
Buttons
Joystick
Fig. 4.14
WARNING!
Avoid knocking your control system and especially the•
joystick.
Be careful not to strike obstacles with the control•
system or joystick when you drive.
Never drop the control system.•
When transporting your wheelchair, make sure that•
the control system is well protected.
Avoid damage to cables.•
To improve the reliability of the control system keep•
exposure to extreme conditions to a minimum.
Do not expose your control system or its components•
to damp for prolonged periods.
If your control system becomes contaminated with•
food or drink clean it off as soon as possible.
DANGER!
In the event of the wheelchair moving in an•
unexpected way RELEASE THE JOYSTICK.
This action will stop the wheelchair under any
circumstances
Do not operate the control system if the wheelchair•
behaves erratically or shows abnormal signs of
heating, sparks or smoke. Turn the control system off
at once and consult your Sunrise Medical authorised
dealer.

HULA 17
Rev.1.0
DANGER!
The Brake release• is only to be used in an
emergency power breakdown situation e.g. When
the wheelchair has to be moved manually to get the
user into a safe environment. It is not intended for
permanent use or to push the wheelchair up/down a
slope with the user sitting in it.
The wheelchair’s automatic braking system will•
not work unless the brake release levers are in the
“DRIVE” position.
Brake release, can also be used if a complete and•
catastrophic loss of power such as control system
failure or battery failure has occurred.
Brake release, should not be habitually used as a•
means of transporting the user as if in a manual
wheelchair.
When the power wheelchair is functioning normally,•
the brake release should only be used to park or
store the unoccupied wheelchair.
Never push the occupied power wheelchair up or•
down a slope with the Brake release in freewheel.
Never attempt to disengage the brake release•
mechanism whilst sitting in the wheelchair,
especially on a slope.
Always ensure the Brake release levers are in the•
drive position before using the wheelchair.
Fig. 5.8
Fig.5.4
Fig.5.7
Fig. 5.6
Fig.5.5
Fig. 5.9
WARNINGS!
Make sure that when the wheelchair is stored•
the controller is switched off and the freewheel
mechanisms are engaged, (in Drive).
Do not lift the wheelchair by any of the plastic shrouds.•
Caution should be taken while the wheelchair is in•
freewheel.
To remove the control pod/joystick:
Loosen the adjustment screw on the control arm and•
slide the arm out of the bracket, (Fig 5.4).
Disconnect the control loom plug located under the•
seat, (Fig.5.5)
Place the controller and arm in a safe place until•
required.
To reconnect the hand control just repeat the process•
in reverse.
5.3 Re-Assembling
Place the backrest into the receivers and tighten the•
lever screws carefully.
If required reconnect the control pod joystick.•
Attach the swing-away leg rests.•
Make sure your freewheel mechanisms are engaged,•
(in DRIVE).
WARNING!
Never lift the wheelchair by the armrests, leg rests•
or any of the shrouds, since they are detachable and
harm could be done to the user or to the wheelchair.
The wheelchair is not designed for use with a hoist,•
(Fig.5.6)
5.4 Brake release (Fig.5.7 - 5.9)
There are two brake release, (freewheel), levers located
under the seat by the battery cover.
Ensure the controller is switched off before you engage•
the release levers – Failure to do so will increase the
force needed to push the wheelchair.
Push the levers forward towards the front of the•
wheelchair to engage DRIVE.
Pull the levers backwards towards the rear of the•
wheelchair to disengage drive, FREEWHEEL.
There is a label located next to each lever to explain•
the operation of the levers.

18 HULA Rev.1.0
5.5 Control pod joystick unit position
WARNING!
Make sure that the control pod/joystick is mounted•
securely and that the joystick position is correct.
The hand or limb you use to operate the joystick•
should be supported, for example by the arm pad.
Do not use the joystick as the sole support for your•
hand or limb - wheelchair movements and bumps
could upset your control of the joystick.
The control pod/joystick is mounted on a sliding
mechanism which enables the control to be moved
forwards and backwards.
Undo the locking screw, (Fig.5.4).•
Slide the control arm either out or to it’s new position,•
(Fig 5.10).
When the most comfortable position has been•
selected, secure the slider by tightening the locking
screw.
WARNING!
Ensure the locking screw is fully tightened prior to use,
especially when transporting your wheelchair.
5.6 Getting ready to drive
Operate the on/off switch. The battery gauge will blink•
then remain on after a second
Check that the maximum speed is set to a level which•
suits you.
Push the joystick to control the speed and direction of•
the wheelchair
Fig. 5.10

HULA 19
Rev.1.0
5.7 Armrests
5.7.1 Armrests-ip up
The armrests on both sides of the wheelchair can be
flipped up to allow side transfer, (Fig. 5.11-5.12).
For side transfer flip the armrest all the way up until it
goes into its mechanical stop. This frees your space for
side transfer.
To bring the armrests back into their position flip it all the
way down until it sits on its mechanical stop. Guide it in its
downward movement and do not let it fall on its own.
5.7.2 Armrest Height Adjustment
The following section outlines armrest height adjustment.
In the case of either fine or coarse adjustment, it is a
two-part process:
PART I: Adjust the armrest height through rotation
PART 2: Adjust arm pad angle.
1.Basic fine adjustment.
PART 1 (fig. 5.13 & 5.14)
Up to one inch of armrest height adjustment can be
achieved using the 5mm fine height adjustment screw to
fine tune the armrest’s height.
Loosen the 6mm rotation bolts on both armrests (A).1.
Turn the adjustment screws (B) counter-clockwise to2.
raise the armrest or clockwise to lower.
Retighten both rotation bolts (A).3.
Tighten (A) 20 Nm or 177lbf/in of torque.
PART 2 (fig. 5.15 & 5.16)
Loosen the 4mm armpad angle pivot bolts (A) on both1.
armrests. Remove the 4mm angle index bolts (B) on
both armrests.
Tilt both arm pads down (or up in the case of a2.
lowered armrest) until the arm pads are in the
preferred angle. Check to see if the height is correct.
Retighten both armpad angle pivot bolts (A). Replace3.
both armpad angle index bolts (B).
Tighten (B) to 10 Nm or 88.5lbf/in of torque for both sets
of bolts.
Fig. 5.14
Fig. 5.16
Fig. 5.11 Fig. 5.12
Fig. 5.13
Fig. 5.15

20 HULA Rev.1.0
2.Basic coarse adjustment.
PART 1
To achieve more than one inch of adjustment, remove1.
the 6mm armrest rotation bolts on both sides of the
seat, (Fig.5.17).
Remove both armrest assemblies. (Fig.5.18)2.
Remove both sets of 4mm armrest adjustment ring3.
bolts.(Fig.5.19)
Rotate the armrest height adjustment rings, (Fig.5.20)4.
to match the desired height designated in the
Configuration Chart, (Fig.5.29), on page 23.
Replace both sets of armrest adjustment ring bolts5.
according to the configuration chart. (Fig.5.21)
Tighten the arm rest height adjustment rings to10 Nm6.
or 88.5lbf/in of torque.
Replace both armrest assemblies. (Fig.5.22)7.
Replace the armrest pivot bolts on both sides of the8.
seat, but do not tighten completely. (Fig.5.23)
Fig. 5.17
Fig. 5.18
Fig. 5.19
Fig. 5.20
Fig. 5.21
Fig. 5.22
Fig. 5.23