Quickie LXI User manual

O w n e r ’ s M a n u a l
Quickie®LXI / LX
Supplier: This manual must be given to the user of this wheelchair.
User: Before using this wheelchair read this entire manual and save
for future reference.
SECTION ENGLISH
LXI / LX

SUNRISE MEDICAL LISTENS
Thank you for choosing a Quickie wheelchair. We want to hear your ques-
tions or comments about this manual, the safety and reliability of your chair,
and the service you receive from your Sunrise supplier. Please feel free to
write or call us at the address and telephone number below:
Sunrise Medical
Customer Service Department
2842 Business Park Ave
Fresno, CA 93727
[phone]
Be sure to return your warranty card, and let us know if you change your
address. This will allow us to keep you up to date with information about
safety, new products and options to increase your use and enjoyment of
this wheelchair. If you lose your warranty card, call or write and we will
gladly send you a new one.
FOR ANSWERS TO YOUR QUESTIONS
Your authorized supplier knows your wheelchair best, and can answer most
of your questions about chair safety, use and maintenance. For future refer-
ence, fill in the following:
Supplier:________________________________________________
Address:________________________________________________
_______________________________________________________
Telephone: ______________________________________________
Serial #: __________________ Date/Purchased: _______________
I. INTRODUCTION
ENGLISH
2
930360 Rev. F

G.Positioning Belts Option .................................................. 13
H.Push Handles Option........................................................ 13
I. Quick-Release Axles ........................................................ 13
. Rear Wheels ...................................................................... 13
K. Rear Wheel Locks ............................................................ 13
L. Modified Seat Systems ..................................................... 13
M.Seat and Back Upholstery .............................................. 13
VIII. USE AND MAINTENANCE ............................................... 14
A.Introduction ........................................................................ 14
B. Critical Maintenance Tips................................................. 14
C.Maintenance Chart ........................................................... 14
D. Cleaning Tips....................................................................... 14
E. Troubleshooting Chart ..................................................... 14
F. To Mount and Remove Rear Wheels............................ 15
G.Axles - Quick Release ...................................................... 15
H.Wheel Locks....................................................................... 15
I. Anti-tip tubes...................................................................... 15
. Flip Back Armrests............................................................. 16
K. Flip-Back Height-Adjustable Armrests .......................... 16
L. Single-Post Height Adjustable Armrests ....................... 16
M.Swing-in/out Hangers and Footrests............................. 17
N.Articulating or Elevating Legrest.................................... 17
O.Backrest................................................................................ 17
P. Cushion ................................................................................ 18
Q.To Fold or Unfold your Wheelchair.............................. 18
R. Check-Out .......................................................................... 18
IX DEALER SERVICE AND AD USTMENT ......................... 19
A.Dealer Service Introduction............................................ 19
B. Critical Maintenance tips ................................................. 19
C.Cleaning................................................................................ 19
D. Axles - Threaded................................................................ 19
E. Adjustable Axle Plate ........................................................ 19
F. Toe-in Toe-out .................................................................... 20
G.Caster Plates....................................................................... 20
H.Caster Mounting ................................................................ 20
I. Wheel Locks....................................................................... 20
. Anti-tip Tubes...................................................................... 20
K. Height-Adjustable Armrests ........................................... 21
L. Swing-in/out Hangers and Footrests............................. 21
M.Backrest................................................................................ 21
N Fitting the ay Precision Back.......................................... 22
O Seat Sling.............................................................................. 23
X. SUNRISE LIMITED WARRANTY ..................................... 23
I. INTRODUCTION ............................................................... 2
II. TABLE OF CONTENTS ...................................................... 3
III. YOUR CHAIR AND ITS PARTS ....................................... 4
IV. NOTICE - READ BEFORE USE ......................................... 5
A.Choose the Right Chair & Safety Options ................. 5
B. Review This Manual Often ............................................. 5
C.Warnings.............................................................................. 5
V. GENERAL WARNINGS....................................................... 5
A.Weight Limits .................................................................... 5
B. Intended Use ..................................................................... 5
C.Attendants and Caregivers.............................................. 5
D. Accessories ........................................................................ 5
E. Know Your Chair .............................................................. 5
F. Reduce The Risk of an Accident ................................... 6
G.Safety Checklist ................................................................. 6
H.Changes & Adjustments .................................................. 6
I. Environmental Conditions .............................................. 6
. Terrain ................................................................................. 6
K. Street Use .......................................................................... 6
L. Motor Vehicle Safety ........................................................ 6
M.When You Need Help ..................................................... 7
VI. SAFETY WARNINGS: FALLS & TIP-OVERS.................. 7
A.Center of Balance ............................................................ 7
B. Dressing or Changing Clothes ...................................... 7
C.Obstacles ............................................................................ 7
D. Front Caster Lift ................................................................ 8
E. Reaching or Leaning .......................................................... 8
F. Moving Backward............................................................... 8
G.Escalators............................................................................. 9
H.Ramps, Slopes & Sidehills ................................................ 9
I. Transfer ................................................................................ 9
. Curbs & Single Steps......................................................... 10
K. Climbing a Curb or Single Step...................................... 10
L. Descending a Curb or Single Step................................. 10
M.Stairs ..................................................................................... 11
N.Climbing Stairs .................................................................. 11
O.Descending Stairs ............................................................. 11
VII. WARNINGS: COMPONENTS & OPTIONS ................. 12
A.Anti-Tip Tubes ................................................................... 12
B. Armrests ............................................................................. 12
C.Cushion & Sling Seats ...................................................... 12
D. Fasteners ............................................................................ 12
E. Footrests.............................................................................. 12
F. Pneumatic Tires ................................................................. 12
II. TABLE OF CONTENTS
ENGLISH
3930360 Rev. F

930360 Rev. F 4
ENGLISH
III. YOUR CHAIR AND ITS PARTS
QUICKIE LXI / LX
1
2
10
4
11
9
8
12
6
5
3
7
13
14
1. Backrest
2. Push Handle
3. Armpad
4. Tire
5. Handrim
6. Quick-release axle
7. Anti-tip
8. Caster Wheel
9. Caster Fork
10. Footplates
11. Swing-away Hanger
12. Seat Sling
13. Seat Cushion
14. Flip-Back Height Adjustable Armrest
Weight
28 lbs. with steel rear axles
Frame Dimensions
Frame width: 12”- 20”
(seat width 1/2” narrower)
Sling depth: 12”-18”
Backrest
8owith push handles
16”-19”, 14”-17”
Backrest options: solid back, backrest cush-
ion, straight push handles
Hanger Type
60o, 70o, 90o, articulating legrest-adult, ele-
vating, 90oelevating
Footplates
Composite, foam, adult angle-adjustable,
kids angle-adjustable, extended, heel loops,
legstrap
Footrest extension tubes: short, medium,
long, high mount
Casters
Std - 8” pneumatic
Opt - 5”, low-profile polyurethane,
6” pneumatic, 6” polyurethane,
8” polyurethane, 3/4” longer fork stem
bolt, 1 1/2” longer fork
stem bolt
Armrests
Std - flip-back with standard pad
Opt - padded swing-away, flip-back with full-
length pad, flip-back height-adjustable with
standard pad, flip-back height-adjustable
with full-length pad.
Axle Plates
Standard, adjustable
Axles
Std - threaded
Opt - quick -release, quad-release axle nuts
Anti-tip Tubes
Rear anti-tip tubes, front anti-tip tubes
Standard Rear Wheels
Std - mag
Opt - spoke
Tire Size
Std - 24”
Opt - 20”, 22”
Tire types
Std - pneumatic
Opt - pneumatic with airless insert,
full-profile polyurethane, low-profile
polyurethane
Handrims
Std - aluminum
Opt - plastic-coated, long tabs
Projections
Opt - vertical, oblique, 6, 8, 10, 12
Wheel Locks
Std - high-push
Opt - high-pull, omit, do not mount,
6” extension handles, grade aids
.
Note: All features may not be available with
some chair setups or in conjunction with
another chair feature. Please consult your
authorized supplier for more information.

930360 Rev. F
5
ENGLISH
IV. NOTICE READ BEFORE USE
A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS
Sunrise provides a choice of many wheelchair styles to meet your needs.
This product is intended for single person use only. Final selection of the
type of wheelchair, options and adjustments rests solely with you and your
health care professional. Choosing the best chair for your unique mobility
needs, will depend on such things as:
1. Your disability, strength, balance and coordination.
2. The types of hazards you must overcome in daily use (where you
live and work, and other places you are likely to use your chair).
3. The need for options that will improve your positioning, safety and
comfort (such as anti-tip tubes, positioning belts, or special seating
systems).
B. REVIEW THIS MANUAL OFTEN
Before using this chair you, and each person who may assist you, should
read this entire manual and make sure to follow all instructions. Review the
warnings often, until they are second nature to you.
C.WARNINGS
The word “WARNING” refers to a hazard or unsafe practice that may cause
severe injury or death to you or to other persons. The “Warnings” are in
three main sections, as follows:
1.V — GENERAL WARNINGS
Here you will find a safety checklist and a summary of risks you
need to be aware of before you ride this chair.
2.VI– SAFETY WARNINGS: FALLS & TIP-OVERS
Here you will learnabout practices for the safe use of your chair, and
how to avoid a fall or tip-over while you perform daily activities in
your chair.
3.VII — WARNINGS — COMPONENTS & OPTIONS
Here you will learn about the components of your chair and options
you can select for safety. Consult your authorized supplier and your
health care advisor to help you choose the best set-up and options
for safe use.
NOTE–Where they apply, you will also find “Warnings” in other sec-
tions of this manual. Heed all warnings in these sections. If you
fail to do so a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
V. GENERAL WARNINGS
A. WEIGHT LIMITS
WARNING
NEVER exceed the weight limit specified by Sunrise Medical. The weight
capacity provided by your manufacturer is for the combined weight of a rider
and items carried using on-board storage. If you do exceed the weight limit,
damage to your chair, a fall, tip-over or loss of control may occur and cause
severe injury to the rider or others.
Weight Capacities
Quickie LX - 250lbs/(113Kg).
Quickie LXI - 265lbs/(120kg).
B. INTENDED USE
The Quickie LX Series of wheelchair's intended use is to provide mobility
to persons limited to a sitting position.
WARNING
DO NOT use this device for purposes other than what is intended by the
manufacturer
1. The wheelchiar is not designed for weight training and is unsafe for
use as a seat while weight training. Weight training from the wheel-
chair substantially changes the stability of the chair and may cause
tipping.
2. DO NOT stand on the frame of the wheelchair.
3. NEVER allow someone to stand on your chair or use it as a step
ladder.
4. This chair is designed for a single rider only.
5. Unauthorized modifications and use of parts or accessories not sup-
plied or approved by Sunrise Medical may change the chair struc-
ture. This will void the warranty and may cause a safety hazard. If
the warning is ignored, damage to your chair, and the potential
severe injury of the person using the chair for unintended purposes
can occur.
C. ATTENDANTS AND CAREGIVERS
WARNING
Before you assist a rider, be sure to read all warnings contained in this
manual, and follow all instructions that apply. Be aware that after consulting
a healthcare advisor, you will need to learn safe and proven body mechanics
to use and create assistive methods best suited to your abilities.
D. ACCESSORIES
WARNING
Unauthorized modifications or use of parts, or accessories not supplied or
approved by Sunrise Medical may change the chair structure. This will void
the warranty and may cause a safety hazard.
Some problems that may occur, but are not limited to:
1. Incorrect Wheels and/or tires that put the rider at risk of a fall or tip-
over.
2. Adding a component to the frame, changing the structural integrity of
the chair.
3. Any modification or disassembly can potentially create an unsafe situa-
tion where rider and/or attendant are put at risk.
E. KNOW YOUR CHAIR
WARNING
Every wheelchair is different. Take the time to learn the feel of this chair
before you begin riding. Start slowly, with easy, smooth strokes. If you are
used to a different chair, you may use too much force and tip over. If you
use too much force, damage to your chair, a fall, tip-over or loss of control
may occur and cause severe injury to the rider or others.

F. REDUCE THE RISK OF AN ACCIDENT
WARNING
1. BEFORE you begin riding, you should be trained in the safe use of this
chair by your health care advisor.
2. Practice bending, reaching and transfers until you know the limit of
your ability. Have someone help you until you know what can cause
a fall or tip-over and how to avoid doing so.
3. Be aware that you must develop your own methods for safe use
best suited to your level of function and ability.
4. NEVER try a new maneuver on your own. Ask the advice of your
health care provider to lower the risk of a fall or tip over.
5. Get to know the areas where you plan to use your chair. Look for
hazards and learn how to avoid them.
G. SAFETY CHECKLIST
WARNING
Before Each Use Of Your Chair:
1. Make sure the chair rolls easily and that all parts work smoothly.
Check for noise, vibration, or a change in ease of use. (This may indi-
cate low tire pressure, loose fasteners, or damage to your chair).
2. Immediately repair any problem. Your authorized supplier can help
you find and correct the problem.
3. Check to see that both quick-release rear axles are locked. When
locked, the axle button will “pop out” fully. If not locked, the wheel
may come off and cause you to fall.
4. If your chair has anti-tip tubes, lock them in place.
H. CHANGES & AD USTMENTS
WARNING
1. See your healthcare advisor and have them adjust seating components
any time a change or adjustment needs to be made.
2. Unauthorized modifications or use of parts not supplied or
approved by Sunrise may change the chair structure. This will void
the warranty and may cause a safety hazard.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to
the rider or others.
I. ENVIRONMENTAL CONDITIONS
WARNING
1. Use extra care if you must ride your chair on a wet or slick surface. If
you are in doubt, ask for help.
2. Contact with water or excess moisture may cause your chair to
rust or corrode. Avoid all extreme weather situations if possible.
a. Do not use your chair in a shower, pool or other body of water.
The chair tubing and parts are not water-tight and may rust or
corrode from the inside.
b. Avoid excess moisture (for example, do not leave your chair in a
damp bathroom while taking a shower).
c. Dry your chair as soon as you can if it gets wet, or if you use
water to clean it.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
. TERRAIN
WARNING
1. Based on ANSI/RESNA testing, Sunrise Medical recommends the use of
a caster wheel with a minimum diameter of 5”, if the wheelchair will be
overcoming obstacles up to 1/2” on a regular basis.
2. Your chair is designed for use on firm, even surfaces such as con-
crete, asphalt, indoor flooring, and carpets.
3. Do not operate your chair in sand, loose soil, or over rocky terrain.
4. If you use your chair on terrain that is rougher than described above
there is a danger that screws and bolts will loosen prematurely, and
that damage to wheels or axles could put the rider at risk of a fall,
tip-over, or loss of control.
K. STREET USE
WARNING
1. This product is not intended for street use.
2. Avoid streets whenever possible.
3. Obey and follow all legal pedestrian pathways, and laws that apply to
pedestrians.
4. Be alert to the danger of motor vehicles in parking lots, or if you
must cross a road.
If you fail to heed this warning, damage to your chair, and a possible colli-
sion may occur and cause severe injury to the rider or others.
L. MOTOR VEHICLE SAFETY
If possible and feasible, the rider should transfer to the Original Equipment
Manufacturer vehicle seat and use the OEM vehicle restraint.
WARNING
Note– Transit only available on LXi model. To Identify whether
your wheelchair has been manufactured with the Transit Option
installed, look for four points of securement. Two Front points (A),
and two rear points (B).
If your chair is NOT equipped with the Transit Option:
1. NEVER let anyone sit in this chair while in a moving vehicle.
a. ALWAYS move the rider to an approved vehicle seat.
b. ALWAYS secure the rider with proper motor vehicle restraints.
2. In an accident or sudden stop the rider may be thrown from the
chair. Wheelchair seat belts will not prevent this, and further injury
may result from the belts or straps.
3. NEVER transport this chair in the front seat of a vehicle. It may shift
and interfere with the driver.
4. ALWAYS secure this chair so that it cannot roll or shift.
5. Do not use any chair that has been involved in a motor vehicle acci-
dent. The frame and/or components may have been changed due to
the accident. Such items could be, but are not limited to: bent, loos-
ened, and/or broken components that were subjected to an impact.
Failure to heed these warnings puts you and others that may assist you at a
high risk of injury.
V. GENERAL WARNINGS
ENGLISH
6
930360 Rev. F
A
B
1

4. To prevent injury to your back, use good posture and proper body
mechanics. When you lift or support the rider or tilt the chair, bend
your knees slightly and keep your back as upright and straight as you
can.
5. Remind the rider to lean back when you tilt the chair backward.
6. When you descend a curb or single step, slowly lower the chair in
one easy movement. Do not let the chair drop the last few inches to
the ground. This may damage the chair or injure the rider.
7. To avoid tripping, unlock and rotate anti-tip tubes up, out of the way.
8. Whenever you aren’t attending the wheelchair, ALWAYS use the
wheel-lock to secure the rear wheels, and lock the anti-tip tubes in
place.
If you fail to ask for help when in doubt, you run a high risk of a fall, tip-
over or loss of control that may occur and cause severe injury to the rider
or others.
M. WHEN YOU NEED HELP
WARNING
For The Rider: Make sure that each person who helps you reads and fol-
lows all warnings and instructions that apply.
For Attendants:
1. Work with the rider’s doctor, nurse or therapist to learn safe meth-
ods best suited to your abilities and those of the rider.
2. Tell the rider what you plan to do, and explain what you expect the
rider to do. This will put the rider at ease and reduce the risk of an
accident.
3. Make sure the chair has push handles. They provide secure points for
you to hold the rear of the chair to prevent a fall or tip-over. Check
to make sure push handle grips will not rotate or slip off.
VI. SAFETY WARNINGS: FALLS & TIP-OVERS
ENGLISH
7930360 Rev. F
A. CENTER OF BALANCE
WARNING
The point where this chair will tip forward, back or to the side depends on
its center of balance and stability. How your chair is set up, the options you
select and the changes you make may affect the risk of a fall or tip-over.
1. The Most Important Adjustment Is:
The position of the rear wheels. The more you move the rear
wheels forward, the more likely your chair will tip over backward.
2. The Center Of Balance Is Also Affected By:
a. A change in the set-up of your chair, including:
• The distance between the rear wheels.
• The amount of rear wheel camber.
• The seat height and seat angle.
• Backrest angle.
b. A change in your body position, posture or weight distribution.
c. Riding your chair on a ramp or slope.
d. A back pack or other options and the amount of added weight.
3. To Reduce The Risk Of An Accident:
a. Consult your doctor, nurse or therapist to find out what axle
and caster position is best for you.
b. Consult your authorized supplier BEFORE you modify or adjust
this chair. Be aware that you may need to make other changes
to correct the center of balance.
c. Have someone help you until you know the balance points of
your chair and how to avoid a tip-over.
d. Use anti-tip tubes.
If you fail to heed these warnings, you are at a high risk of a fall, tip-over or
loss of control that could cause severe injury to the rider or others.
B. DRESSING OR CHANGING CLOTHES
WARNING
Your weight may shift if you dress or change clothes while seated in this
chair.
To reduce the risk of a fall or tip-over:
1. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
2. Lock anti-tip tubes in place. (If your chair does not have anti-tip
tubes, back it up against a wall and lock both rear wheels).
If you fail to heed this warning, damage to your chair, a fall, tip-over or loss
of control may occur and cause severe injury to the rider or others.
C. OBSTACLES
WARNING
Riding over curbs or obstacles can cause tipping and serious bodily harm.
If you have any doubt that you can safely cross any curb or obstacle,
ALWAYS ASK FOR HELP. Be aware of your riding skills and personal limi-
tations. Develop new skills only with the help of a companion.
To avoid the risk of traversing obstacles:
1. Keep a lookout for danger – scan the area well ahead of your chair
as you ride.
2. Make sure the floor areas where you live and work are level and free
of obstructions.
3. Remove or cover threshold strips between rooms.
4. Install a ramp at entry or exit doors. Make sure there is not a drop
off at the bottom of the ramp.
5. To Help Correct Your Center Of Balance:
a. Lean your upper body FORWARD slightly as you go UP over an
obstacle.
b. Press your upper body BACKWARD as you go DOWN from a
higher to a lower level.
6. If your chair has anti-tip tubes, do not go over an obstacle without
help.
7. Keep both of your hands on the handrims as you go over an obsta-
cle.
8. Never push or pull on an object (such as furniture or a doorjamb)
to propel your chair.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. FRONT CASTER LIFT
WARNING
Front caster lift can occur when the front wheels, ordinarily in contact with
the ground, are either intentionally, or unintentionally caused to lift from
the ground while the rear wheels remain in contact. Pitch control (partial
or full) should NEVER be attempted without consulting your healthcare
advisor and making sure that anti-tips are installed.
If you fail to heed this warning, you are at a high risk of damage to your
chair, a fall, tip-over or loss of control that may occur and cause severe
injury to the rider or others.
V. GENERAL WARNINGS

E. REACHING OR LEANING
WARNING
If you reach or lean it will affect the center of balance of your chair. This
may cause you to fall or tip over. When in doubt, ask for help or use a
device to extend your reach.
1. NEVER reach or lean if you must shift your weight sideways or rise up
off the seat.
2. NEVER reach or lean if you must move forward in your seat to do
so. Always keep your buttocks in contact with the backrest.
3. NEVER reach with both hands (you may not be able to catch your-
self to prevent a fall if the chair tips).
4. NEVER reach or lean to the rear unless your chair has anti-tip tubes
locked in place.
5. DO NOT reach or lean over the top of the seat back. This may
damage one or both backrest tubes and cause you to fall.
6. If You Must Reach Or Lean:
a. Do not lock the rear wheels. This creates a tip point and makes
a fall or tip-over more likely.
b. Do not put pressure on the footrests.
c. Move your chair as close as you can to the object you wish to
reach.
d. Do not try to pick up an object from the floor by reaching
down between your knees. You are less likely to tip if you reach
to the side of your chair.
e. Rotate the front casters until they are as far forward as possible.
This makes the chair more stable.
f. Firmly grasp a rear wheel or an armrest with one hand. This will
help to prevent a fall if the chair tips.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
F. MOVING BACKWARD
WARNING
Use extra care when you move your chair backward. Your chair is most
stable when you propel yourself forward. You may lose control or tip over
if one of the rear wheels hits an object and stops rolling.
1. Propel your chair slowly and smoothly.
2. If your chair has anti-tip tubes, make sure to lock them in place.
3. Stop often and check to be sure your path is clear.
If you fail to heed this warning, you are at a high risk of damage to your
chair, a fall, tip-over or loss of control that may occur and cause severe
injury to the rider or others.
G. ESCALATORS
WARNING
NEVER use this chair on an escalator, even with an attendant. If you do, a
fall or tip-over is likely.
H. RAMPS, SLOPES & SIDEHILLS
WARNING
Whenever possible, avoid riding on a slope, which includes a ramp or side-
hill. This will change the center of balance of your chair. Your chair is less
stable and more difficult to manuever. when it is at an angle. When moving
up a hill, anti-tip tubes may not prevent a fall or tip-over.
1. Do not use your chair on a slope steeper than 10%. (A 10% slope
means: one foot in elevation for every ten feet of slope length.
2 3 4 5
2. Always go as straight up and as straight down as you can. (Do not
“cut the corner” on a slope or ramp.)
3. Do not turn or change direction on a slope.
4. When you have to use a ramp, always stay in the CENTER of the
ramp. Make sure ramp is wide enough that you have no risk of going
off the edge.
5. Do not stop on a steep slope. If you stop, you may lose control of
your chair.
6. NEVER use rear wheel locks to try to slow or stop your chair. This
is likely to cause your chair to veer out of control.
7. ALWAYS be aware of:
a. Wet or slippery surfaces.
b. A change in grade on a slope (or a lip, bump or depression).
These may cause a fall or tip-over.
c. A drop-off at the bottom of a slope or ramp. A drop-off as
small as 3/4 inch can stop a front caster and cause the chair to
tip forward.
8. To Reduce The Risk Of A Fall Or Tip-Over:
a. Lean or press your body UPHILL. This will help adjust for the
change in the center of balance caused by the slope or sidehill.
b. Keep pressure on the handrims to control your speed on a
down slope. If you go too fast you may lose control.
c. Ask for help any time you are in doubt.
9. Ramps At Home & Work– For your safety, ramps at home and work
must meet all legal requirements for your area:
a. Avoid A Drop Off. You may need a section at the top or bot-
tom to smooth out the transition.
b. Always stay in the center of the ramp and control your speed.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and can possibly cause severe injury to the rider
or others.
VI. SAFETY WARNINGS: FALLS & TIP-OVERS
ENGLISH
8
930360 Rev. F
23
45
IF you need to go down a hill:
a. The downslope should be less
than 10°
b. GO SLOW
c. ALWAYS go straight down
d. ALWAYS control your speed
e. DO NOT Turn on the hill.
IF you need to go up a hill:
a. The Upslope should be less
than 10°
b. ALWAYS go straight up
c. NEVER stop on the upslope
d. NEVER turn on a hill.
e. ALWAYS lean orward.
IF you need to traverse a sidehill:
a. The sidehill must be less than
6° or you risk a tip-over
b. DON’T STOP
c. ALWAYS go straight down
d. DO NOT Turn on the hill.
IF you need to traverse a ramp:
a. Go slowly
b. Watch out or Drop-o s.
c. ALWAYS go straight down.
d. Stay centered on the ramp.
e. ALWAYS lean orward.

I. TRANSFERS
WARNING
It is dangerous to transfer on your own. It requires good balance and agility. Be aware that there is a
point during every transfer when the wheelchair seat is not below you. To avoid a fall:
1. Work with your health care advisor to learn safe methods for transfers.
a. Learn how to position your body and how to support yourself during a transfer.
b. Have someone help you until you learn safe transfer methods.
2. Lock the rear wheels before you transfer.
3. Be aware that the chair can still slide and/or tip. The wheel lock keeps the rear wheels from
rolling while you are perforrming the transfer.
4. Make sure that the pneumatic tires are properly inflated. Low tire pressure may allow the rear
wheel locks to slip. (see table in Section G “Pneumatic Tires”
5. Move your chair as close as you can to the seat you are transferring to.
If possible, use a transfer board.
6. Rotate the front casters until they are as far forward as possible.
7. If you can, remove the footrests, or swing them out of the way.
a. Make sure your feet do not catch in the space between the footrests.
b. Avoid putting weight on the footrests as this may cause the chair to tip.
8. Make sure armrests are removed, or out of the way and do not interfere with the transfer.
9. Transfer as far back onto the seat surface as you can. This will reduce the risk that the chair will
tip or move away from you.
6 7
ENGLISH
9930360 Rev. F
6
Be ore trans erring, remove the arm-
rests, and ootrests, and make sure the
wheel lock is set.
Optimum Trans er position
VI. SAFETY WARNINGS: FALLS & TIP-OVERS
GET READY TRANSFER ADJUST
7
1.
GET READY TRANSFER ADJUST
2. 3.

930360 Rev. F 10
ENGLISH
. CURBS & SINGLE STEPS
WARNING
Before riding over curbs, and negotiating even a single step, ALWAYS ask for assistance first. Curbs and
steps can cause tipping and serious bodily harm. When in doubt as to your ability to avoid, or traverse
any obstacle, always ask for help. Be aware of your riding skills and personal limitations. Develop new
skills only with the help of a companion.
For Attendant: Each person who assists the rider with curbs and steps should read and follow all
instructions and warnings pertaining to attendants, and caregivers.
1. Do not try to climb a high curb or step (more than 4 inches high) UNLESS you have help. Doing so
may cause your chair to exceed its balance point and tip over.
2. Go straight up and straight down a curb or step. If you climb or descend at an angle, a fall or tip-
over is likely.
3. Be aware that the impact of dropping down from a curb or step can damage your chair or loosen
fasteners.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
can possibly cause severe injury to the rider or others.
K. CLIMBING A CURB OR SINGLE STEP
WARNING
For Attendant: follow these steps to help the rider climb a curb or single step going FORWARD:
1. Stay behind the chair.
2. Face the curb and tilt the chair up on the rear wheels so that the front casters clear the curb or
step.
3. Move forward, placing the front casters on the upper level as soon as you are sure they are past
the edge.
4. Continue forward until the rear wheels contact the face of the curb or step. Lift and roll the rear
wheels to the upper level.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
L. DESCENDING A CURB OR SINGLE STEP
WARNING
For Attendant:: Follow these steps to help a rider descend a curb or single step going BACKWARD:
1. Stay at the rear of the chair.
2. Several feet before your reach the edge of the curb or step, turn the chair around and pull it
backward.
3. While looking over your shoulder, carefully step back until you are off the curb or stair and
standing on the lower level.
4. Pull the chair toward you until the rear wheels reach the edge of the curb or step. Then allow
the rear wheels to slowly roll down onto the lower level.
5. When the rear wheels are safely on the lower level, tilt the chair back to its balance point. This
will lift the front casters off the curb or step.
6. Keep the chair in balance and take small steps backward. Turn the chair around and gently lower
front casters to the ground.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
8
8
8
8
VI. SAFETY WARNINGS: FALLS & TIP-OVERS

930360 Rev. F
11
ENGLISH
M. STAIRS
WARNING
1. NEVER use this chair on stairs UNLESS you have someone to help you. Doing so is likely to cause a
fall or tip-over.
2. Negotiating stairs with a wheelchair always requires at least 2 attendants for safety.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
N. CLIMBING STAIRS
WARNING
1. Use at least two attendants to move a chair and rider up stairs.
2. Move the chair and rider BACKWARD up the stairs.
3. The person at the rear is in control. He or she tilts the chair back to its balance point.
4. A second attendant at the front firmly grasps a non-detachable part of the front frame and lifts
the chair up and over one stair at a time.
5. The attendants move to the next stair up. Repeat for each stair, until you reach the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
O. DESCENDING STAIRS
WARNING
1. Use at least two attendants to move a chair and rider down stairs.
2. Move the chair and rider FORWARD down the stairs.
3. The person at the rear is in control. He or she tilts the chair to the balance point of the rear
wheels and rolls it to the edge of the top step.
4. A second attendant stands on the third step from the top and grasps the chair frame. He or she
lowers the chair one step at a time by letting the rear wheels roll over the stair edge.
5. The attendants move to the next stair down. Repeat for each stair, until you reach the landing.
If you fail to heed these warnings damage to your chair, a fall, tip-over or loss of control may occur and
cause severe injury to the rider or others.
9
9
9
9
VI. SAFETY WARNINGS: FALLS & TIP-OVERS

930360 Rev. F 12
ENGLISH
F. FOOTRESTS
WARNING
1. At the lowest point, footrests should be AT LEAST 2 inches off the
ground. If set too LOW, they may “hang up” on obstacles you can expect to
find in normal use. This may cause the chair to stop suddenly and tip for-
ward.
2. To Avoid A Trip Or Fall When You Transfer:
a. Make sure your feet do not “hang up” or get caught in the space
between the footrests.
b. Avoid putting weight on the footrests, as the chair may tip for-
ward.
c. Footrests should be swung out of the way or removed whenever
entering or exiting the wheelchair.
3. NEVER lift this chair by the footrests. Footrests detach and will not
bear the weight of this chair. Lift this chair only by non-detachable
parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
E. PNEUMATIC TIRES
WARNING
Proper inflation extends the life of your tires and makes your chair easier
to use.
1. Do not use this chair if any of the tires are under- or over-inflated.
Check weekly for proper inflation level, as listed on the tire sidewall.
2. Low pressure in a rear tire may cause the wheel lock on that side to
slip and allow the wheel to turn when you do not expect it.
3. Low pressure in any of the tires may cause the chair to veer to one
side and result in a loss of control.
4. Over-inflated tires may burst.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
A. ANTI-TIPS
WARNING
Anti-tip tubes can help keep your chair from tipping over backward in
normal conditions.
1. Sunrise recommends the use of anti-tip tubes:
2. When locked in place (in the “down” position) anti-tip tubes should
be BETWEEN 1 1/2 to 2 inches off the ground.
a. If set higher than 2 inches, they may not prevent a tip-over.
b. If set lower than 2 inches, they may “hang up” on obstacles and
cause a fall or tip over.
3. If you have to climb or descend a curb, or overcome an obstacle it
may be necessary to have an attendant make sure the anti-tip tubes
are rotated up, and out of the way, so that the chair and rider do
not get stuck and/or become unstable.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
B. ARMRESTS
WARNING
Armrests detach and will not bear the weight of this chair.
1. NEVER lift this chair by its armrests. They may come loose or break.
2. Lift this chair only by non-detachable parts of the main frame.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
C. CUSHIONS & SLING SEATS
WARNING
1. Quickie sling seats and standard foam cushions are not designed for
the relief of pressure.
2. If you suffer from pressure sores or if you are at risk that they will
occur, you may need a special seat system or a device to control your
posture. Consult your doctor, nurse or therapist to find out if you
need such a device for your well-being.
3. Seat slings are not intended to be used as a direct seating surface. A
cushion or other seating surface should be placed on the sling
before use.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
D. FASTENERS
WARNING
Many of the screws, bolts and nuts on this chair are special high-strength
fasteners. Use of improper fasteners may cause your chair to fail.
1. ONLY use fasteners provided by an authorized supplier (or ones of
the same type and strength, as indicated by the markings on the
heads).
2. Over- or under-tightened fasteners may fail or cause damage to
chair parts.
3. If bolts or screws become loose, tighten them as soon as you can.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
VII. WARNINGS: COMPONENTS AND OPTIONS
Recommended Tire Pressures

930360 Rev. F
13
ENGLISH
K. REAR WHEELS
WARNING
A change in set-up of the rear wheels will affect the center of balance of
your chair.
1. The farther you move the rear axles FORWARD, the more likely it
is that your chair will tip over backward.
2. Consult your healthcare advisor to find the best rear axle set-up for
your chair. Do not change the set-up UNLESS you consult your health-
care advisor first.
3. Adjust the rear wheel locks after you make any change to the rear
axles.
a. If you fail to do so, the wheel locks may not work.
b. Make sure lock arms embed in the tires at least 1/8 inch when
locked.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
L. REAR WHEEL LOCKS
WARNING
Rear wheel locks are NOT designed to slow or stop a moving wheelchair.
Use them only to keep the rear wheels from rolling when your chair is at a
complete stop.
1. NEVER use rear wheel locks to try to slow or stop your chair when
it is moving. Doing so may cause a fall or tip-over
2. To keep the rear wheels from rolling, always set both rear wheel
locks when you transfer to or from your chair.
3. Low pressure in a rear tire may cause the wheel lock on that side to
slip and may allow the wheel to turn when you do not expect it.
4. Make sure lock arms embed in tires at least 1/8 inch when locked. If
you fail to do so, the locks may not work.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
M. MODIFIED SEAT SYSTEMS
WARNING
Use of a seat system not approved by Sunrise may alter the center of bal-
ance of this chair. This may cause the chair to tip over.
1. Do not change the seat system of your chair UNLESS you consult
your authorized supplier first.
2. Use of a seating system not approved by Sunrise may affect the fold-
ing mechanism of this chair.
3. Use of a seating system not provided by Sunrise is prohibited for
transit use.
N. SEAT AND BACK UPHOLSTERY
WARNING
1. Replace worn or torn fabric of seat and seat back as soon as you can. If
you fail to do so, the seat or seat back may fail.
2. Sling fabric will weaken with age and use. Look for fraying, thin spots,
or stretching of fabrics especially at edges and seams.
3. “Dropping down” into your chair will weaken fabric and result in
the need to inspect and replace the seat more often.
4. Be aware that laundering or excess moisture will reduce the flame
retardation qualities of the fabric.
5. If Tension Adjustable upholstery is present, loosen straps or remove
upholstery prior to folding or unfolding the chair.
H. POSITIONING BELTS (OPTION)
WARNING
Use positioning belts ONLY to help support the rider’s posture. Improper
use of these belts may cause severe injury to or death to the rider.
1. Make sure the rider does not slide down in the wheelchair seat. If
this occurs, the rider may suffer chest compression or suffocate due
to pressure from the belts.
2. The belts must be snug, but must not be so tight that they interfere
with breathing. You should be able to slide your open hand, flat,
between the belt and the rider.
3. A pelvic wedge or a similar device can help keep the rider from slid-
ing down in the seat. Consult with the rider’s doctor, nurse or ther-
apist to find out if the rider needs such a device.
4. Use positioning belts only with a rider who can cooperate. Make
sure the rider can easily remove the belts in an emergency.
5. NEVER Use Positioning Belts:
a. As a patient restraint. A restraint requires a doctor’s order.
b. On a rider who is comatose or agitated.
c. As a motor vehicle restraint. In an accident or sudden stop the
rider may be thrown from the chair. Wheelchair seat belts will
not prevent this, and further injury may result from the belts or
straps.
I. PUSH HANDLES (OPTION)
WARNING
When you have an attendant, make sure that this chair has push handles.
1. Push handles provide secure points for an attendant to hold the rear
of this chair, to prevent a fall or tip-over.
2. Check to make sure push handle grips will not rotate or slip off.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
. QUICK-RELEASE AXLES
WARNING
1. Do not use this chair UNLESS you are sure that both quick-release
rear axles are locked.
2. An axle is not locked until the quick-release button pops out fully.
3. An unlocked axle may come off during use, resulting in a fall, tip-over
or loss of control and cause severe injury to the rider or others.
• Quick-Release Axles should be periodically cleaned and inspected
for function and signs of wear or bending. Replace as necessary.
If you fail to heed these warnings damage to your chair, a fall, tip-over or
loss of control may occur and cause severe injury to the rider or others.
10
VII. WARNINGS: COMPONENTS & OPTIONS
10

VIII. USE AND MAINTENANCE
930360 Rev. F 14
ENGLISH
WARNING
The owner of this chair is responsible for making sure that it has been
setup and adjusted by a trained service professional under the advice of a
healthcare advisor. The chair may require periodic maintenance or cer-
tain in-use adjustments that may be performed by the owner or caregiver.
A. INTRODUCTION
1. Proper maintenance will improve performance and extend the useful
life of your chair.
2. Clean your chair regularly. This will help you find loose or worn
parts and make your chair easier to use. You will need a mild deter-
gent solution and plenty of cleaning rags.
3. If discovered, repair or replace loose, worn, bent or damaged parts
before using the chair.
4. To protect your investment, have all major maintenance and repair
work done by your authorized dealer.
5. Inspect and maintain this chair strictly per the maintenance chart.
6. If you detect a problem, make sure to order parts, or have service,
and repair work done at your authorized dealer before use.
7. At least once per year, have a complete inspection, safety check,
and service of your chair made by an authorized dealer.
B. CRITICAL MAINTENANCE TIPS
1. Tire Air Pressure:
Check air pressure in pneumatic tires at least ONCE PER WEEK. The
wheel locks will not grip properly if you fail to maintain the air pressure
shown on tire sidewall.
2. Axles & Axle Sleeves:
When checking axles and axle sleeves every six months,
make sure they are clean and tight. Loose sleeves will damage
the axle plate and will affect performance.
D. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent at least once
a month.
b. Protect the paint with a coat of non-abrasive auto wax every three
months.
2. Axles and Moving Parts
a. Clean around axles and moving parts WEEKLY with a slightly damp
(not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving
parts.
3. Upholstery
a. Hand-wash (machine washing may damage fabric).
b. Drip-dry only. DO NOT machine dry as heat will damage fabric.
4. Basic Maintenance Materials available at local store
a. Tire Pump
b. Clean rags or cotten cloth.
c. Teflon-based Lubricant
d. Mild Detergent.
NOTE– You do not need to grease or oil the chair.
Weekly 3 Months 6 Months Annually
Tire inflation level
Wheel locks
All fasteners for wear and tightness
Armrests
Axle and axle sleeves
Quick-release axles
Wheels, tires and spokes
Casters
Anti-tip tubes
Frame and crossbrace
Upholstery
Service by Authorized Supplier
Check...
C. MAINTENANCE CHART  Make sure tire pressure is correct and equal in both
rear tires and front caster tires, if pneumatic.
Make sure all nuts and bolts are snug. (Note: Do not
overtighten or aluminum tubes may be damaged.)
 Make sure all spokes and nipples are tight on radial
spoke wheels.
Use Tri-Flow Lubricant (Teflon®-based) between all
modular frame connections and parts.
  Check for proper caster fork adjustment. See
instructions for caster fork adjustment.
Add a spacer washer between the plastic saddle and
the caster plate on the top of the left caster plate.
Add a spacer washer between the plastic saddle and
the caster plate on the bottom right caster plate
retaining bolts.
Add a spacer washer between the plastic saddle and
the caster plate on the top of the right caster plate.
Add a spacer washer between the plastic saddle and
the caster plate on the bottom left caster plate
retaining bolts.
 Make sure both front casters touch the ground
simultaneously. if they do not, add spacers between
the bottom bearing of the caster plate and fork stem
nut until they do. Check for this on a flat surface.
Symptom
Left turn in chair Right Turn in chair Looseness in chair Sluggish turning Squeaks and rattles Caster flutter
Solution:
E. TROUBLESHOOTING CHART

930360 Rev. F
15
ENGLISH
F. TO MOUNT & REMOVE REAR WHEELS
WARNING
Do not use this chair UNLESS you are sure both quick-release axles are locked. An unlocked axle may come
off during use and cause a fall.
Note: Axle is not locked until:
a. The quick-release button (A) pops out fully.
b. The ball bearings are fully visible on the outside of the sleeve.
1. To Install Wheel:
a. Depress quick-release button (A) fully. This will release tension on ball bearings at other end.
b. Insert axle through hub of rear wheel.
c. Keep pressure on button (A) as you slide axle (B) into axle sleeve (C)
d. Release button to lock axle in sleeve. Adjust axle if it does not lock.
e. Repeat steps on other side.
2. To Remove Wheel:
a. Depress quick-release button (A) fully.
b. Remove wheel by sliding axle (B) out of axle sleeve (C).
c. Repeat steps on other side.
G. AXLES - QUICK RELEASE
a. Depress the quick-release button (A) on the axle.
b. Slide through wheel hub and into axle sleeve until it locks.
c. The axle is not secured until the outside quick-release button pops out to its fully extended position.
d. The ball bearing on the opposite end of the axle must be fully visible beyond the end of the axle
sleeve.
e. Quick-Release Axles should be inspected for function and any signs of wear or bending. Replace as
necessary.
H. WHEEL LOCKS
Quickie LXI wheelchair are shipped with one of two types of high-mount wheel locks.
WARNING
Wheel locks are installed at Sunrise and should be adjusted by your qualified service person.
Inspect wheel locks weekly per the maintenance chart. Do not use your chair UNLESS you are sure both
wheel-locks can fully engage. A wheel-lock that is not correctly adjusted may allow your chair to roll, or turn
unexpectedly.
Wheel-locks must be adjusted after making sure the tires have the correct air pressure. When fully engaged,
the arm should be imbedded into the tire at least 1/8” to be effective.
If you find the wheel locks have slipped or are not working correctly contact your service provider for prop-
er adjustment.
I. ANTI-TIP TUBES
Sunrise Medical recommends the use of Anti-tip tubes in every situation.
NOTE: Use a torque setting of 115 in.-lbs. when setting up the anti-tip tubes.
1. Inserting Anti-Tip Tubes Into Receiver
a. Press the rear anti-tip release lever on the anti-tip tube so that both release pins are drawn inside.
b. Insert into the anti-tip tube receiver.
c. Turn the anti-tip tube down until release pin is through the receiver mounting hole.
d. Insert second anti-tip tube the same way.
2. Turning Anti-Tip Tubes up.
a. Press the rear anti-tip tube release lever.
b. Hold lever in and turn anti-tip tube up.
c. Release lever.
d. Repeat with second anti-tip tube.
e. Remember to return anti-tip tubes
to down position after completing maneuver.
11
12
13
14 15
VIII. USE AND MAINTENANCE
CB
11
12
14
15
A
13

930360 Rev. F 16
ENGLISH
2. Adjusting Anti-Tip Tube Wheel
The anti-tip tube wheels may have to be raised or lowered to achieve the proper clearance of
1 1/2” to 2”.
a. Press the anti-tip wheel release button (A) so that both release pins are drawn inside.
b. Raise or lower to one of the three predrilled holes.
c Release button.
d. Adjust the second anti-tip tube wheel the same way. Both wheels should be at exactly the same
height.
. FLIP-BACK ARMRESTS
Flip-back armrests are shipped standard on Quickie LXI wheelchairs. They are installed by Sunrise.
To flip armrests back, depress the release latch and pull arm toward back of
wheelchair.
K. FLIP-BACK HEIGHT AD USTABLE ARMRESTS
Flip-back height-adjustable armrests are installed by Sunrise.
1. Height-Adjustment
a. Release the upper securing lever (2).
b. Slide armpad (1) up or down to desired height.
c. Return lever (2) to locked position.
2. Flipping Armrest Back and Removing Armrest
a. Depress the release latch (3) and pull arm toward back of wheelchair.
b. To remove, pull up on armrest. Pin (6) securing armrest will automatically release.
c. To return armrest to operating position, push armpad down until it locks firmly into place.
L. SINGLE-POST HEIGHT-AD USTABLE ARMRESTS
1. Installation
a. Slide the outer armpost (1)into the receiver (2) mounted to the wheelchair frame.
b. The armrest will automatically lock into place.
2. Height Adjustment
a. Rotate release lever(3) to second stop.
b. Slide armrest pad (4) up or down to desired height.
c. Return lever (3) to locked position against armpost.
d. Push arm pad until upper armpost locks firmly into place.
3. Removing Armrest
a. Rotate release lever to first stop and remove the armrest.
4. Replacing Armrest
a. Slide armrest back into receiver(2).
b. Return release lever to locked position against armpost.
16
17
18
19
Flip-Back Height Adjustable
1. Armrest pad
2. Upper securing lever
3. Release latch
4. Armrest panel
5. Rear receiver
6. Armrest release pin
17
18
1
2
3
4
5
6
53
6
4
1
2
Height Adjustable
1. Outer Armpost
2. Standard receiver
3. Release lever
4. Armrest pad
5. Transfer bar
6. Side panel
7. Outer armpost tension adjust-
ment set screws
8. Inner armpost
9. Receiver adjustment bolts
8
7
9
19
16
A
VIII. USE AND MAINTENANCE

930360 Rev. F
17
ENGLISH
M. SWING-IN/OUT HANGERS AND FOOTRERSTS
(60°, 70°, 70° “V”, or 90°)
1. Installation
a. Place swing-in/swing-out pivot saddle into the receiver (A) on front frame tube with the footrest
facing outward from the frame.
b. Rotate the footrest inward until it locks into place on locking bolt.
2. Removal
a. To remove footrest, push release latch (B) toward the frame.
b. Rotate footrest inward and lift. Or, pull footrest away from frame and rotate outward.
3. Height Adjustment
NOTE– It is recommended that you maintain a minimum of 2.0 inches between the lowest point on the
footrest and the floor.
a. Loosen set screw (C) using a 3/16 inch hex key.
b. Slide footrest extension up or down inside frame tube to desired height.
c. Tighten set screw. Use a torque setting of 144 in-lbs (16.27 Nm).
N. ARTICULATING OR ELEVATING LEGREST
1. Installation
a. To install or remove the Articulating legrest (ALR) or elevating legrest (ELR) see instructions above for
(Swing-in/out hangers and Footrests)
2. Adjustment
a. To raise legrest, lift to desired position. Legrest will automatically lock in place.
b. To Lower, while seated in the chair, press the release lever (D) forward and lower legrest to desired
position, the legrest will automatically lock in place.
O. BACKREST
Quickie LXI wheelchairs are shipped with an 8º bend.
P. CUSHION (option)
Installation
a. Place cushion on seat sling with VELCRO®side down. The beveled edge of the cushion should be in
front.
b Press firmly into place.
WARNING
Possible pinch point. If seat sling is not present during folding or unfolding, pinch top of seat rail
securely without wrapping fingers around the seat rail. Use flat palms to depress the chair
if opening.
20
21 22
Articulating Legrest
Elevating Legrest
21
22
20
VIII. USE AND MAINTENANCE
A
B
C
D
D

930360 Rev. F 18
ENGLISH
Q. TO FOLD OR UNFOLD YOUR WHEELCHAIR
NOTE: You can remove quick-release wheels before you fold chair (and
re-mount them before you unfold chair).
1. To Fold the Chair:
a. Move sure footrests are out of the way before you fold chair.
(Swing-away, flip up or remove footrests.)
b. Remove cushion (if any).
c. Grasp center of seat sling and lift sharply until chair folds.
2. To Unfold the Chair:
a. Stand to one side of chair. Check to make sure footrests do not
interfere.
b. Tilt chair toward you far enough to take the weight off the opposite
wheel.
c. Push down on the seat rail closest to you until chair opens fully.
d. Make sure seat rail tubes snap into frame saddles.
R. CHECK-OUT
After the wheelchair is assembled and adjusted, it should roll
smoothly and easily. All accessories should also perform smoothly.
If you have any problems, follow these procedures.
If you have any problems, follow these procedures:
1. Review the set-up and check-out section and operating guide to make
sure chair was properly prepared.
2. Review troubleshooting guide.
3. If your problem persists, contact your authorized supplier. If you still
have a problem after contacting your authorized supplier, contact
Sunrise customer service. See the introduction page for details on
how to contact your authorized supplier or Sunrise customer serv-
ice.
VIII. USE AND MAINTENANCE

930360 Rev. F
19
ENGLISH
IX. DEALER SERVICE & ADJUSTMENT
WARNING
The owner of this chair is responsible for makiing sure that it has been setup and adjusted by a trained serv-
ice professional under the advice of a healthcare advisor. Service and/or adjustments should only be done
with the advice of a healthcare professional. Always use parts and/or accessories that have been recom-
mended and approved by Sunrise Medical when servicing this chair.
A. DEALER SERVICE INTRODUCTION
1. At least once per year, this chair should have a complete inspection, safety check, and regular service
made by an authorized dealer. The tools at right are a good start for proper maintenance.
2. Torque settings– A torque setting is the optimum tightening which should be made on a particular fas-
tener. It is important to use proper torque settings where specified. When not specified, torque set-
tings should be 60 in-lbs
3. If you have discovered a worn, bent, or damaged part, repair or replace them with recommended parts
before returning this chair to service..
4. All major maintenance and repair work should be done by the authorized dealer.
B. CRITICAL MAINTENANCE TIPS
1. Torque settings:
A torque setting is the optimum tightening which should be made on a particular fastener. It is important to
use proper torque settings where specified. When not specified, torque settings should be 60 in-lbs
2. Dealer Service and Adjustment Reference materials:
Go to www.sunrisemedical.com for parts manuals, instruction sheets, and instructional videos that will aid in
the repair of the Quickie 2 Family of wheelchairs.
C. CLEANING
1. Paint Finish
a. Clean the painted surfaces with mild soap or detergent.
b. Protect the paint with a coat of non-abrasive auto wax.
2. Axles and Moving Parts
a. Clean around axles and moving parts with a slightly damp (not wet) cloth.
b. Wipe off or blow away any fluff, dust or dirt on axles or moving parts.
c. DO NOT USE 3 in 1 oil, or WD-40 ® for lubrication. Only use Teflon based Lubricant when working
on this wheelchair.
D. AXLES - THREADED
1. Adjustment
a. Remove inside bolt (A) from axle and remove axle and wheel.
b. Insert the axle into desired axle plate position.
c. Re-attach the wheel, and tighten the axle bolt (B) .
E. AD USTABLE AXLE PLATE
The adjustable axle plate can be adjusted to three different positions. Camber can be adjusted from 0º-5º by adding or
removing spacers. Quickie LXI wheelchair with adjustable axle plates are shipped with 1º of camber.
NOTE: Use a torque setting of 144 in./lbs. to tighten axle nut.
1. Adjustment
a. Remove four retaining bolts (C) and nuts on axle plate.
b. Move axle plate forward or rearward to desired position.
c. If desired, add or remove spacers between axle plate and frame to change camber. For 4º or 5º of
camber, longer bolts and extra spacers must be purchased before installation.
d. Insert all four bolts back into axle plate and frame. Tighten nuts.
e. Repeat on opposite side of wheelchair.
f. Axle plate and camber must be exactly the same on both sides of the wheelchair.
24
25
23
TOOLS YOU WILL NEED
1. Imperial Hex key set
2. Metric Hex key set
3. Imperial Open-end Wrench set
4. Metric Open-end Wrench set
5. Torque wrench
6. Imperial Hex bit Socket set
7. Metric Hex bit Socket set
8. Phillips and Flat screwdrivers
25
24
23
A
B
C

930360 Rev. F 20
ENGLISH IX. DEALER SERVICE & ADJUSTMENT
F. TOE-IN AND TOE-OUT
Toe-in and Toe-out terms are terms that relate to how well the rear wheels of the chair are aligned. This will
affect how well the chair will roll. Drag or resistance occurs in a wheelchair when the rear wheels are not
properly aligned.
Toe-in can be slightly adjusted for by adding or removing wave washers between the axle plate and rear frame
tube. To make this adjustment:
a. Remove rear wheel (see axle instructions).
b. Remove axle plate (see axle plate instructions).
c. Add or remove wave washers between rear frame and axle plate. (Wave washers may be purchased
from an authorized supplier.)
d. Reinstall axle plate bolts.
e. Reinstall rear wheel (see axle instructions)
f. Repeat on opposite side of wheelchair.
G. CASTER PLATES
NOTE: Use a torque setting of 75 in./lbs. when adjusting caster angle.
1. Angle Adjustment
a. Loosen the two eccentric bolts (A) that secure the caster assembly. Do not remove the clevis pin.
b. Place a large right triangle (B) against the table surface and the front surface of the caster bearing
housing. This will align the caster stem rotational axis perpendicular to the floor surface.
c. When alignment is satisfactory, retighten the two eccentric bolts.
d. Repeat the process for the other caster.
H. CASTER MOUNTING
Forward or Rearward Placement
a. Remove caster housing covers.
b. Remove the two eccentric bolts from each caster.
c. Move left-side caster to right side.
d. Move right-side caster to left side.
e. Remount casters to caster bracket.
Mounting casters forward whenever possible is recommended.
I. WHEEL LOCKS
NOTE: Use a torque setting of 115 in.-lbs. when setting up wheel locks.
1. Adjustment
a. Loosen the screws on the top of each clamp. Do not attempt to remove one screw at a time.
b. Slide assembly toward rear wheel until clamp embeds into tire to prevent wheel movement, when in
locked position.
c. Adjust angle position.
d. Tighten screws.
26
29
27
28
26
27
28
29
A
B