QuietCool AFG SMT-3.0 User manual

SEE // HEAR // FEEL
THE QUIETCOOL DIFFERENCE
ADVANCED WHOLE HOUSE FANS
®
THE NATURAL CHOICE FOR ENERGY SAVINGS!
INSTALLATION GUIDE
SPECIALTY SERIES FANS

2QUIETCOOLSYSTEMS.COMQUIETCOOLSYSTEMS.COM
GENERAL SAFETY INSTRUCTIONS
1. Read Instructions - All safety and operation instructions must be read. Failure to read and follow
instructions as stated in this guide may void applicable warranty.
2. Retain Instructions - The safety and operating instructions should be kept for future reference.
3. Heed Warnings - All warnings should be followed.
4. Follow Instructions - All installing and operating instructions should be followed.
5. Heat - The QuietCool system should be situated away from heat sources.
6. Damage Requiring Service - Only qualified service personnel should service the QuietCool system.
The user should not attempt to service the product.
7. Building Codes - Always follow Local Building Codes when installing appliances
CONTENTS
1. SYSTEM OVERVIEW......................................................1
1.1 Introduction.......................................................1
1.2 Features ..........................................................1
1.3 Benefits...........................................................2
1.4 System Venting Requirements .....................................2
2. INSTALLATION ..........................................................3
2.1 Installing AFG Model Fans..........................................3
2.2 Installing GA Model Fans...........................................4
2.3 Installing GX Model Fans ...........................................5
2.4 Installing RM Model Fans ..........................................6
3. WIRING .................................................................8
3.1 Specialty Fan Wiring - Smart. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
3.2 Specialty Fan Wiring - Thermostat ..................................9
3.2 Specialty Fan Wiring - Timer .......................................10
4. SYSTEM OPERATING INSTRUCTIONS ................................... 11
4.1 QuietCool Smart Attic Fan......................................... 11
4.2 QuietCool Pro Attic Gable Fan ..................................... 11
4.3 QuietCool Garage Fans ............................................12
4.4 QuietCool Roof Mount Fans .......................................12
WARRANTY ...............................................................13
ADVANCED WHOLE HOUSE FANS
®
QC Manufacturing, Inc.
43352 Business Park Drive
Temecula, CA 92590
PH 951.325.6340
FX 951.325.6351
QuietCoolSystems.com

3
1-888-QUIETCOOL 1 1-888-QUIETCOOL
1. SYSTEM OVERVIEW
1.1 INTRODUCTION
Congratulations on the purchase of your new QuietCool Specialty Series Fan!
The QuietCool Specialty Series was designed for every application imaginable. QuietCool Specialty Series
fans dominate the market in energy efficiency. Our Specialty Series works great in practically all climate
zones and most homes, mobile homes, and even warehouse buildings!
QuietCool Attic Fans: The QuietCool Attic Fans are the best in the business. New for 2017, we offer the
AFG SMT-3.0, the first smart attic fan on the maket, and the most energy efficient too! We also have the
AFG PRO-3.0, the most powerful residential attic fan on the market.
QuietCool Garage Fans: The QuietCool Garage Fans offer great ventilation options for your garage, man cave,
or workshop. We offer the GA ES-1500 to ventilate both your garage and attic, and the GX ES-1100 to ventilate
your garage only, with a wall mount design.
QuietCool Roof Mount Fans: The QuietCool Roof Mount Fans offer great versatility for any system you are
looking to put in. QuietCool Roof Mount Fans can be used as an attic fan, as a whole house fan with a duct, or
as a whole house fan that pulls air through air intake grilles in multiple rooms.
1.2 Series Features
• High Efficiency Design
• Designed and Built in California
• 15 Year Warranty
• Attic Gable Fans
• Garage Fans
• Roof Mount Fans

2QUIETCOOLSYSTEMS.COM
1.3 Benefits
1.4 System Venting Requirements
VERY IMPORTANT! - 1 SQUARE FOOT OF NET FREE VENT AREA PER 750 CFM
RECOMMENDED! - 2 TO 4 SQUARE FEET OF INLET VENTS PER FAN
Vent Type Model Type Average Size Venting Sq. Ft.
Gable vent 12” x 19.5” 1.20
Dormer Vent 14” x 8” 0.70
Eave Vent Various Various
Ridge Vent Various Various
Soffit Vent Various Various

3
1-888-QUIETCOOL
2. INSTALLATION
2.1 Installing AFG model fans
NOTE: The AFG model fans are designed to mount behind existing louvers. If no louver exists,
one must be installed. Louver should be installed in the upper center section of the
gable. For maximum efficiency, the area of the louver should be greater than the size
of the ventilator. Any louver area not covered by the ventilator should be sealed off to
prevent any possible air leakage.
Installing the QuietCool AFG is very easy. The mounting tabs on the
AFG should be attached to the Attic Gable Fan. There should also be
mounting hardware in the box to fasten the gable fan to the boards
that frame the gable vents. To install the AFG, simply mount the gable
fan to your gable vents as shown in the following steps:
Flush Mount: The AFG can be mounted flush to a rectangular type louver
by fastening through the mounting brackets to the frame of the louver
(as shown in Figure 2.1A).
As stated in the note above, any area of the louver that is not covered
by the AFG must be sealed off in order to prevent air leakage, which may
hinder performance.
This is the most conventional method of mount the AFG. We recommend
using the Flush Mount option if possible for all applications.
Wide Mount: The AFG can be mounted on a wide louver, but
additional mounting steps must be taken in order for the fan to
work properly. As shown in Figure 2.1B, two additional boards must
be fastened to the boards framing the gable vent so the AFG can be
mounted securely.
As stated in the note above, any area of the louver that is not
covered by the AFG must be sealed off in order to prevent air
leakage, which may hinder performance.
Figure 2.1A
Figure 2.1B
Installation Video:
Watch the video by
scanning the QR
code or visit www.
QuietCoolSystems.com/
support

4QUIETCOOLSYSTEMS.COM
Odd Mount: The AFG can also be mounted off center for an
odd shaped louver (as shown in Figure 2.1C).
As stated in the note above, any area of the louver that is not
covered by the AFG must be sealed off in order to prevent air
leakage, which may hinder performance.
While this is not the most ideal way to mount the gable fan, it
is possible. However, since the fan is not completely covering
the vent, maximum airflow will not be achieved.
NOTE: The AFG can be mounted on many other types of louvers, including triangle
vents, round vents, half-round vents, etc. If the vent is smaller than the area of the
fan, we recommend constructing a chamber that surrounds the vent, and then mount
the AFG to the chamber to ensure maximum airflow and performance.
2.2 Installing GA model fans
VERY IMPORTANT: MINIMUM OF 26” CLEARANCE REQUIRED ABOVE CEILING FOR
INSTALLATION OF GA MODEL FANS. ALWAYS FOLLOW LOCAL BUILDING CODES.
1. Determine in which area you would like to install your QuietCool Garage Attic Fan. Now it’s time to find
the exact location using a stud finder. Locate the ceiling studs and mark the location for the fan to
be installed. (see Figure 2.2A) One side of the cut out should be directly next to a wood member for
proper fan mounting and support.
2. When you find the location, mark a 14 1/4” square using a framing square or template. Make sure you
have 2” of clearance all the way around it. The grille that will be installed later is a 16” square. (see
Figure 2.2B)
3. Starting at one corner of the square using a drywall saw, cut out the opening. Remove the drywall
cutout and clear away insulation (if applicable). (see Figure 2.2C)
4. Take the GA fan model into the attic and place it over the ceiling cut out. Attach the fan using screws
into the ceiling joists. (see Figure 2.2D). Install the ceiling grille. (see Figure 2.3H)
VERY IMPORTANT: CHECK TO MAKE SURE FAN BLADE SPINS FREELY AND THE FIRE DAMPER
CLOSES EASILY. MAKE SURE TO SECURE THE LATCH IN THE OPEN POSITION
AVOID BACKDRAFTS: MAKE SURE THE GARAGE FAN WILL NOT BACKDRAFT COMBUSTION
APPLIANCES IN THE GARAGE. QUIETCOOL GARAGE FANS MOVE LARGE QUANTITIES OF AIR.
Figure 2.1C

5
1-888-QUIETCOOL
2.3 Installing GX model fans
1. Determine in which area you would like to install your QuietCool Garage Exterior Mount Fan. Now it’s
time to find the exact location using a stud finder. Locate the wall studs and mark the location for
the fan to be installed (see Figure 2.2A). One side of the cut out should be directly next to a wood
member for proper fan mounting and support.
2. When you find the location, mark a 14 1/4” square using a framing square or template. Make sure you
have 2” of clearance all the way around it. The grille that will be installed later is a 16” square (see
Figure 2.2B).
3. Starting at one corner of the square using a drywall saw, cut out the opening. Remove the drywall
cutout and clear away insulation (if applicable) (see Figure 2.2C).
4. From the interior, drill a hole through the exterior at the four corners of the cut out (see Figure
2.3A).
5. Go to the exterior and place the square wall mounting bracket aligned to the 4 drilled holes. Using a
level, mark the inside of the bracket with a pencil (see Figure 2.3B).
6. Using a saw or angle grinder, cut out the marked area of stucco or siding (see Figure 2.3C).
7. Remove cut out of exterior stucco or siding. Then cut out any applicable sheathing.
8. Now install the exterior cover frame. Make sure the frame is level and then attach the four corners
with long enough screws to penetrate the wood studs. Note: Predrilling may be required (see Figure
2.3D).
Figure 2.2A Figure 2.2B Figure 2.2C Figure 2.2D
Figure 2.3A Figure 2.3B Figure 2.3C Figure 2.3D

6QUIETCOOLSYSTEMS.COM
9. Place fan into the cut out area. Fasten the fan in each 4 corners to the vertical wood studs (see
Figure 2.3E).
10. Caulk exterior around frame (see Figure 2.3F).
11. Attach the exterior cover to mounting frame using 4 sheet metal screws (see Figure 2.3G).
12. Mount inside wall grille (see Figure 2.3H).
2.4 Installing RM model fans
1. Determine in which area you would like to install your QuietCool Roof Mount Fan. (see Figure 2.4D)
IMPORTANT: If you are installing the RM fan as a ducted fan, it’s time to find the exact location for
your ceiling box and grille using a stud finder. Locate the wall studs and mark the location for the box
to be installed. Minimum of 20” clearance required. Make sure the duct will fit between the fan
location and the ceiling box location. Using a drywall saw, cut out the drywall.
2. Drill 4 reference holes to mark where you will be cutting the roof. If you are installing the RM ES-1100,
mark a 14 1/4” x 14 1/4” square. If you are installing the RM ES-2200, mark a 16 1/4” x 16 1/4” square.
(see Figure 2.4A)
3. Move to the roof and, using a circular saw, cut out the square. (see Figure 2.4B)
4. With the square cut out, place the roof mount fan over the cutout. (see Figure 2.4C)
5. Fasten the fan to the roof using appropriate connectors for your roof material.
6. Flash in fan curb using appropriate weatherproofing method and materials based on roof material.
IMPORTANT: If you are installing the RM fan in a flat or cathedral ceiling application, find the
location for your ceiling box and grille using a stud finder. Locate the wall studs and mark the
location for the box to be installed. Using a drywall saw, cut out the drywall. The move on to
step 7. If installing as an attic fan, you are done!
7. Place the ceiling box (if applicable) over the ceiling cut out. Attach the ceiling box using screws into
the ceiling joists. (see Figure 2.2D) Install the ceiling grille. (see Figure 2.3H)
Figure 2.3E Figure 2.3F Figure 2.3G Figure 2.3H

7
1-888-QUIETCOOL
EXTREMELY IMPORTANT: It is very important that you install the RM fans correctly, as shown
in the following diagram, as it will dramatically affect the sound level of the fan. NEVER install the
ceiling grille directly underneath the fan. Always offset at least two feet.
Figure 2.4A Figure 2.4B Figure 2.4C
Figure 2.4D: Roof Mount Application Diagrams
Flat Roof - No Duct: Works with CRB and FLT Models
Sloped Roof - No Duct: Works with SLP Models
Flat Roof - With Duct: Works with CRB and FLT Models
Sloped Roof - With Duct: Works with SLP Models

8QUIETCOOLSYSTEMS.COM
3. WIRING
NOTE: Wiring Diagrams are for examples ONLY. Wiring should be done by an experienced
electrician.
NOTE: Your fan may have come with the thermostat pre-wired to a power cord. If this is the case,
simply mount the thermostat or junction box, find a power source in your attic, and plug the
fan in. If you would like to hard-wire the fan, or it is required by your local building codes, please
follow the wiring instructions below.
3.1. Specialty Fan Wiring - Smart
The Smart Attic Fan has the thermostat and humidistat built into the motor. This makes the installation extremely
simply.
1. For this installation, you will need a 2 wire Romex.
2. Open up the junction box from the fan. Remove the power cord. Bring your 2 wire Romex from the power
source into the junction box.
3. With a wire nut, tie the white common wire together. Then tie the black wires together.
4. Ground the green wire from the fan and the ground wire from the Romex to the junction box.
NOTE: When the Smart Attic Fan is connected to power for the first time, it will start in test mode.
It will run for 60 seconds to ensure it runs properly. After 60 seconds, if the temperature is in
operating range (as shown on page 11), the fan will continue to run. If the temperature is not in
operating range, the fan will shut off. If the fan does not come on the first time it is connected to
power, there may be a problem with the wiring. Please contact us if you have any issues.
Figure 3.1A: Smart Attic Fan at the Junction Box
Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power Source
14-2 Wire
14-2 Wire
ADVANCED ATTIC GABLE FANS
®Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power Source
14-2 Wire
14-2 Wire
ADVANCED ATTIC GABLE FANS
®

9
1-888-QUIETCOOL
3.2 Specialty Fan Wiring - Thermostat
For wiring of a Specialty Series Fan with a thermostat. This wiring method works with all of our Specialty
Series fans, but we do not recommend using it with a Roof Mount fan that is being used as a whole house fan.
1. For this installation, you will need a 2 wire Romex, and a thermostat.
2. Open up the thermostat that is connected to the fan. Remove the power cord. Bring your 2 wire Romex
from the power source into the thermostat.
3. With a wire nut, tie the white common wires together.
4. Tie the black wire from the fan to one of the black wires from the thermostat. Either black wire from the
thermostat will work.
5. Tie the black wire from the power source to the remaining black wire from the thermostat.
6. Using the ground screw in the thermostat, ground your power source and the green wire from the fan.
7. Mount the thermostat to one of the joists near the attic fan.
WIRING THE THERMOSTAT REMOTELY:
1. For this installation, you will need a 2 wire Romex, junction box, and a thermostat.
2. Open up the thermostat that is connected to the fan. Remove the power cord. Remove the bracket
mounting the thermostat to the flex tubing and remove the thermostat.
3. Mount the junction box to the flex tubing with the included bracket and mount the junction box. Bring
your 2 wire romex from the power source into the junction box.
Figure 3.2A: Thermostat Wiring
Ground the fan and power to the thermostat
using the green ground screw
Specialty Series Fan
Power Source
14-2 Wire
14-2 Wire
60° Thermostat
FAN ON
TEMPERATURE
90°
120°
®
ADJUSTABLE
TEMPERATURE THERMOSTAT
CAUTION
Automatically started device -to reduce the
risk of injury disconnect from power supply
before servicing. For residential use only. See
instructions for wiring diagram.
60°
ADVANCED ATTIC GABLE FANS
®Ground the fan and power to the thermostat
using the green ground screw
Specialty Series Fan
Power Source
14-2 Wire
14-2 Wire
60° Thermostat
FAN ON
TEMPERATURE
90°
120°
®
ADJUSTABLE
TEMPERATURE THERMOSTAT
CAUTION
Automatically started device - to reduce the
risk of injury disconnect from power supply
before servicing. For residential use only. See
instructions for wiring diagram.
60°
ADVANCED ATTIC GABLE FANS
®

10 QUIETCOOLSYSTEMS.COM
4. Mount the thermostat in the best location for thermostat readings. Run a 2 wire Romex from the
junction box to the thermostat. Tape the white wire on each side of the 2 wire Romex to indicate that
it is a switch leg.
5. In the junction box, with a wire nut, tie the white common wires together. Using the green ground
screw, ground the green wire from the fan and the 2 wire Romex from the thermostat, to the junction
box. Tie the black wire from the fan to the taped white wire from the thermostat. Tie the black wire
from the power source to the black wire from the thermostat. Replace the cover on the junction box.
6. In the themostat, tie the black wire to one of the black wires from the thermostat. Tie the taped wire
to the other black wire from the thermostat. Using the ground screw in the thermostat, ground the
ground wire from the 2 wire Romex.
3.3 Specialty Fan Wiring - Timer
For wiring of a Specialty Series Fan with a timer. This wiring method works with all of our Specialty Series fans.
1. For this installation, you will need a 2 & 3 wire Romex, and an 8 Hour Timer.
2. Begin wiring the timer. From your 3 wire Romex, using a wire nut, tie the two red wires together, the
two white wires together, the two black wires together, and the two ground wires together.
3. Open up the junction box that is connected to the fan. Bring your 2 wire and 3 wire into the junction
box.
3. Tie the white common wires from the fan, the power source, and the timer together. Then, using the
green ground screw, ground the green wire from the fan to the handy box.
4. With a wire nut, tie the black wire from the fan to the red wire from the timer.
Figure 3.2B: Thermostat Wiring in a Remote Location
Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power Source
14-2 Wire
14-2 Wire
14-2 Wire
60°
Thermostat
FAN ON
TEMPERATURE
90°
120°
®
ADJUSTABLE
TEMPERATURE THERMOSTAT
CAUTION
Automatically started device - to reduce the
risk of injury disconnect from power supply
before servicing. For residential use only. See
instructions for wiring diagram.
60°
ADVANCED ATTIC GABLE FANS
®Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power Source
14-2 Wire
14-2 Wire
14-2 Wire
60°
Thermostat
FAN ON
TEMPERATURE
90°
120°
®
ADJUSTABLE
TEMPERATURE THERMOSTAT
CAUTION
Automatically started device - to reduce the
risk of injury disconnect from power supply
before servicing. For residential use only. See
instructions for wiring diagram.
60°
ADVANCED ATTIC GABLE FANS
®

11
1-888-QUIETCOOL
5. Then, tie the black wire from the power source to the black wire from the timer.
6. Lastly, tie the copper ground wire from the power source to the copper ground wire from the timer.
4. SYSTEM OPERATING INSTRUCTIONS
4.1 QuietCool Smart Attic Fan
QuietCool Attic Fans work almost everywhere, almost anytime. During the summer, an attic can be 40-50
degrees hotter than the outside temperature, which in turn heats up the house much faster. With an attic fan,
you can cool the attic to the same temperature as it is outside, greatly reducing the house from heating as
quickly.
With the QuietCool Smart Attic Fan, gone are the days of having to adjust the thermostat for your attic fan.
Featuring a built-in thermostat and humidistat, the self-adjusting, 10-speed ECM motor is always reading the
temperature and humidity in the attic.
When the fan detects temperature over 80 degrees, or humidity over 60%, the Smart Attic Fan comes on at the
lowest speed. As the attic starts to heat up, the Smart Attic Fan automatically adjusts it’s speed.
Temp. 80° 85° 90° 95° 100° 105° 110° 115° 120° 125°+
Humidity 60%+ N/A N/A N/A N/A N/A N/A N/A N/A N/A
Speed 1 2 3 4 5 6 7 8 9 10
CFM 963 1343 1513 1641 1841 2014 2119 2356 2500 2830
Watts 15 18 25 34 49 60 79 99 117 145
*All specs are approximate. For the most up-to-date specs, please visit QuietCoolSystems.com
Figure 3.3A
Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power
Source
14-2 Wire
14-2 Wire
8 HOUR
4 HOUR
2 HOUR
1 HOUR
HOLD
Bare Copper Wires Tied
Together
Match Wire
Colors Together
14-3 Wire
ADVANCED ATTIC GABLE FANS
®
Ground the fan to the junction box
using the green ground screw
Specialty Series Fan
Junction
Box
Power
Source
14-2 Wire
14-2 Wire
8 HOUR
4 HOUR
2 HOUR
1 HOUR
HOLD
Bare Copper Wires Tied
Together
Match Wire
Colors Together
14-3 Wire
ADVANCED ATTIC GABLE FANS
®

12
With the QuietCool Smart Attic Fan, the attic will help your attic stay cooler than a traditional single-speed attic
fan, and will help save you energy by running the fan at a lower speed (thus a lower wattage) when the attic is
not as hot.
4.2 QuietCool Pro Attic Gable Fan
QuietCool Attic Fans work almost everywhere, almost anytime. During the summer, an attic can be 40-50
degrees hotter than the outside temperature, which in turn heats up the house much faster. With an attic fan,
you can cool the attic to the same temperature as it is outside, greatly reducing the house from heating up as
quickly.
The AFG PRO-3.0 is the most powerful residential attic fan on the market. Moving over 3000 CFM at just 250
watts, this fan exhuasts the attic of hot, stale air very quickly and very efficiently. In fact, it is up to 3 times more
efficient and up to 2 times more powerful than an average big box store attic fan.
Simply set your thermostat and forget about your QuietCool Attic Fan!
4.3 QuietCool Garage Fans
QuietCool Garage Fans work great to cool your garage, man cave, or workshop. Our two models work for different
application. Our GA ES-1500 works to cool and ventilate your garage and the attic above your garage. This greatly
reduced the heat transfer between the attic and garage on really hot days. Our GX ES-1100 works well to cool
and ventilate your garage. Run both of these fans when it is cooler outside than it is in your garage.
Don’t let your garage get hot and worry about damage to your vehicles, motorcycles, boat, etc.; just install a
QuietCool Garage Fan!
4.4 QuietCool Roof Mount Fans
The QuietCool (RM) Roof Mount Fans are the most versatile fans that we offer. They can be used as an attic fan,
a whole house fan with a duct, or a whole house fan with multiple inlet vents. QuietCool Roof Mount Fans also
work where a conventional QuietCool Whole House Fan will not. Roof Mount fans work with homes that have a
sealed attic, manufactured homes with no attic, homes with cathedral ceilings, and even industrial buildings
such as warehouses.
If you installed your Roof Mount as a whole house fan, run the fan when it is cooler outside than it is inside your
home. Be sure to crack open a few select windows in your home and let the Roof Mount fan do the rest.
If you installed your Roof Mount as an attic fan, set your thermostat and let it run! When installed as an attic
fan, it is effective almost everywhere, almost anytime.
If you have any trouble installing or operating your new QuietCool Specialty Series Fan, please visit our website
at www.QuietCoolSystems.com or call us at 951-325-6340 for support.
QuietCool is Proudly Designed and Built in California

13
1-888-QUIETCOOL
SPECIALTY SERIES FANS LIMITED WARRANTY
15 YEAR LIMITED WARRANTY
PRODUCT INFORMATION
QC Serial # QC Serial #
QC Serial # QC Serial #
QUIETCOOL SPECIALTY SERIES FANS
QC Manufacturing Inc. extends this warranty to the original purchaser of the following QuietCool
Specialty Series Fans ---- AFG SMT-3.0, AFG PRO-3.0, AFG ES-1500, GA ES-1500, GX ES-1100, RM ES-1100,
RM ES-2200 ---- installed and used in a residence under normal conditions within the United States:
A. Fifteen year coverage applies to the QuietCool motor fan assembly. At our option we will repair or
replace any part of the assembly should it fail to operate during the first fifteen years from the
date of original purchase.
B.One year coverage for all other components including grills, housings, controls and accessories
furnished by QC Manufacturing Inc. At our option we will repair or replace any part which fails as a
result of defective material or workmanship during the rst year from the original date of purchase.
C.This warranty does not cover any of the following:
1. Incidental or consequential damage resulting from the operation of our equipment or any
malfunction thereof.
2. Cost of service calls to diagnose the cause of problems or the labor charge to un-install any
components.
3. Product failure or damage due tofaulty installation, abuse, misuse, unauthorized alteration to
factory specs, lack of maintenance, or transportation damage.
4. Shipping or postage for warranty claims.
D.To obtain service under this warranty, contact the dealer where you purchased the equipment.
If you are unable to find or reach your dealer, contact Customer Service at QC Manufacturing, Inc.,
at the number below
This warranty is the only warranty extended by QC Manufacturing, Inc. to purchasers or suppliers of our equipment. QC Manufacturing Inc. disclaims all other
warranties, express or implied, that arise by operation of the law.
Rev.3.29.17
E.Registration is no longer required for QuietCool fans. If service is required under this warranty,
you must retain your proof or purchase.
ADVANCED WHOLE HOUSE FANS
®
MAKERS OF THE QUIETCOOL ADVANCED WHOLE HOUSE FAN

14
1-888-QUIETCOOL
ADVANCED WHOLE HOUSE FANS
®
QuietCool is Proudly Designed and Built in California
43352 Business Park Drive, Temecula, CA 92590 // PH 951.325.6340 // QUIETCOOLSYSTEMS.COM