Quoizel QR787 User manual

PACKAGE CONTENTS
Part
A
C
B
D
Description
Mirror Hanger
Lock Screw
Hanger Nail
Self-tapping Screw
Quantity
2pcs
2pcs
1pc
1pc
WARNINGS AND CAUTIONS
!
PREPARATION
ASSEMBLY INSTRUCTION
INSTRUCTION SHEET IS QR787-
STYLE NUMBER: QR787
ISSUED 07-2009
1 OF 3
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
, .
. .
A
B
C
D
CAUTION:
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture.
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
Estimated Assembly Time : 15 30 minutes
Tools Required for Assembly (not included) : Flathead screwdriver Phillips screwdriver, pliers.
●
●
●
-
,
E
F
G
E
F
G
Holder
Mirror Frame
Mirror
2pcs
1pc
1pc
STEP 1:
*
.
.
Quoizel recommends 2 people for each step.
a Place the Mirror Frame onto a flat working surface with the
back facing you. Carefully locate the Mirror and Backing
into the channels on the Holders (Welded on the Frame).
b Locate the another two Holders onto the edge of the Mirror
and Backing, line up holes on the Holders and mounting
holes on the Mirror Frame. Using screwdriver, thread the
Lock Screws into the Mounting Holes on the Mirror Frame
and hand tighten until snug to secure them together.
Mirror
Frame
Mirror with
Backing
Mounting Hole
Holder (Welded
on the Frame)
Lock Screw
Holder

2 OF 3
STEP 2:
a Lift and position where the Mirror will reside on the wall
surface and with a tape measure, mark distance from floor
to the bottom edge of the frame with a pencil. Mark should
be located at a point representing ½ of mirror width.
b. Place the Mirror on a flat surface with back facing you.
Measure the distance from the bottom edge of the Mirror
Frame to Hanger on the bottom of the Mirror Frame. This
represents distance “B” in the illustration.
c. With tape measure, add this distance to Mark “A” on wall
surface and mark with pencil.
d. Measure distance between the Hangers on the top and
bottom of the Mirror Frame. With tape measure, add this
distance from Mark “B” and mark with pencil.
e. Measure 3” up from Mark “C” and mark. These marks are
locators for the Mirror Hanger.
.
Make sure
Mark “B” and Mark “C” are vertical.
FOR VERTICAL
Hanger
"A”
Floor
Surface
STEP 3:
a Screw the Self-tapping Screw into the Mark “B” as shown.
Please be sure there are proper length left for supporting
the Hanger on the bottom of the Frame.
b
.
.Locate the Mirror Hanger and align the top center with 3”
Locator mark. Secure them to wall surface with Hanger
Nails. Please be noted that the Mirror Hangers are fully
adjustable.
STEP 4:
a With the help of another person, pass the Holder on the bottom of the Frame over the Self-tapping Screw
and pass the Holder on the top of the Frame over the Mirror Hanger so that the Hanger rests on the inside
of the Bracket Catches.
c If needed, using Adjustment Screws on Mirror Hanger to achieve the proper hanging height.
.
.
STEP 5:
a Clean glass with household glass cleaner. Retain this sheet for future reference..
½ WIDTH
Hanger Nail Mirror Hanger
Adjustment
Screw
Bracket Catch Mark "C"
Hanger (on the bottom
of the Frame)
Hanger (on the top
of the Frame)
STYLE NUMBER: QR787
ASSEMBLY INSTRUCTIONS
BACK
Hanger
Mark "B"Self-tapping
Screw

3 OF 3
FOR HORIZONTAL
ASSEMBLY INSTRUCTIONS
STYLE NUMBER: QR787
STEP 6:
a Lift and position where the Mirror will reside on the wall
surface and with a tape measure, mark distance from floor
to the bottom edge of the frame with a pencil. Mark should
be located at a point representing ½ of mirror width.
b. Place the Mirror on a flat surface with back facing you.
Measure the distance from the bottom edge of the Mirror
Frame to Hanger on the bottom of the Mirror Frame. This
represents distance “B” in the illustration.
c. With tape measure, add this distance to Mark “A” on wall
surface and mark with pencil.
d. Measure distance between the Hangers on the top and
bottom of the Mirror Frame. With tape measure, add this
distance from Mark “B” and mark with pencil. Make sure
Mark “B” and Mark “C” are vertical.
e. Measure 3” up from Mark “C” and mark. These marks are
locators for the Mirror Hanger.
.Hanger
"A”
Floor
Surface
STEP 7:
a Screw the Self-tapping Screw into the Mark “B” as shown.
Please be sure there are proper length left for supporting
the Hanger on the bottom of the Frame.
b Locate the Mirror Hanger and align the top center with 3”
Locator mark. Secure them to wall surface with Hanger
Nails.
.
.
Please be noted that the Mirror Hangers are fully
adjustable.
STEP 8:
a With the help of another person, pass the Holder on the bottom of the Frame over the Self-tapping Screw
and pass the Holder on the top of the Frame over the Mirror Hanger so that the Hanger rests on the inside
of the Bracket Catches.
c If needed, using Adjustment Screws on Mirror Hanger to achieve the proper hanging height.
.
.
STEP 9:
a Clean glass with household glass cleaner. Retain this sheet for future reference..
½ WIDTH
Hanger Nail Mirror Hanger
Adjustment
Screw
Bracket Catch Mark "C"
Hanger (on the bottom
of the Frame)
Hanger (on the top
of the Frame)
BACK
Hanger
Mark "B"Self-tapping
Screw