Quoizel JA43225PN User manual

PACKAGE CONTENTS
Part
A
E
C
B
F
D
Description
Mirror Hanger
Lock Screw
Hanger Nail
Mirror with Backing
Crossbar
Mirror Frame
Quantity
4pcs
4pcs
4pcs
1pc
2pcs
2pcs
1pc
WARNINGS AND CAUTIONS
!
PREPARATION
PREPARATION
INSTRUCTION SHEET IS JA43225-
STYLE NUMBERS JA43225PN and JA43225BN:
ISSUED 09-2008 REVISED 2015-11-13
1OF3
A
B
C
E
D
F
CAUTION:
These instructions are provided for your safety. It is very important that they are read completely before
the installation of your fixture.
●
Before beginning installation of product, make sure all parts are present. Compare parts with package
contents list and diagram above. If any part is missing or damaged, do not attempt to assemble, install or
operate the product. Contact customer service for replacement part.
Estimated Assembly Time : 15 30 minutes
Tools Required for Assembly (not included) : Flathead screwdriver Phillips screwdriver, pliers.
●
●
●
-
,
STEP 1:
*
.
.
.
Quoizel recommends 2 people for each step.
a Place the Mirror Frame onto a flat working surface with the
back facing you. Carefully locate the Mirror with Backing
onto the Mirror Frame.
b Locate Crossbars onto the Mirror Frame and match the
holes on them onto the Mounting Holes on the Mirror
Frame.
c Pass Steel Washers over Lock Screws and then thread the
Lock Screws into the Mounting Holes on the Mirror Frame
and hand tighten until snug to secure them together.
Mirror Frame
Lock Screw
Mounting Hole Mirror with
Backing
Crossbar
G
GSteel Washer
Steel Washer

ASSEMBLY INSTRUCTIONS
2OF3
STYLE NUMBER JA43225PN, JA43225BN:
STEP 2:
a Lift and position where the Mirror will reside on the wall
surface and with a tape measure, mark distance from floor
to the bottom edge of the frame with a pencil. Mark should
be located at a point representing ½ of mirror width.
b. Place the Mirror on a flat surface with back facing you.
Measure the distance from the bottom edge of the Mirror
Frame to the top edge of the Square Hole on Crossbar. This
represents distance “B” in the illustration.
c. With tape measure, add this distance to Mark “A” on wall
surface and mark with pencil.
d. Measure distance between 2 Square Holes on Crossbars.
Add this ½ distance from Mark “B” on each side and mark
with pencil. (Distance “C” in the illustration)
e. Measure 3” up from Mark “C” and mark. These marks are
locators for the (2)Mirror Hangers. Check for marks
straightness with level.
.
FOR VERTICAL
Crossbar
Square Hole
"A”
Floor
Surface
STEP 3:
a Locate Mirror Hangers and align the top center with 3”
Locator mark. Secure them to wall surface with Hanger
Nails.
b With Mirror Hangers properly installed, be sure to make sure
that the (2)Bracket Catches are approximately equal in
length from the top of Mirror Hangers. Adjust overall length
with Adjustment Screws.
.
.
Please be noted that the Mirror Hangers are fully
adjustable allowing for easy leveling.
STEP 4:
a With the help of another person, pass the holes on Crossbars over the Mirror Hangers so that the
Crossbars rests on the inside of the Bracket Catches.
c If needed, adjust mirror for straightness by eye or use level. Make corrections using Adjustment Screws on
Mirror Hangers.
.
.
STEP 5:
a Clean glass with household glass cleaner. Retain this sheet for future reference..
½ WIDTH
"B”
"C”
C
Hanger Nail
Mirror Hanger
Adjustment
Screw
Bracket Catch
Mark "B"
Crossbar
3
”

3OF3
,
STEP 6:
a Lift and position where the Mirror will reside on the wall
surface and with a tape measure, mark distance from floor
to the bottom edge of the frame with a pencil. Mark should
be located at a point representing ½ of mirror width.
b. Place the Mirror on a flat surface with back facing you.
Measure the distance from the bottom edge of the Mirror
Frame to the top edge of the Square Hole on Crossbar. This
represents distance “B” in the illustration.
c. With tape measure, add this distance to Mark “A” on wall
surface and mark with pencil.
d. Add 6” from Mark “B” on each side and mark with pencil.
This represents Mark “C” in the illustration.
e. Measure 3” up from Mark “C” and mark. These marks are
locators for the (2)Mirror Hangers. Check for marks
straightness with level.
.
FOR HORIZONTAL
Top Crossbar
"A”
Floor
Surface
STEP 7:
a Locate Mirror Hangers and align the top center with 3”
Locator mark. Secure them to wall surface with Hanger
Nails.
b With Mirror Hangers properly installed, be sure to make
sure that the (2)Bracket Catches are approximately equal
in length from the top of Mirror Hangers. Adjust overall
length with Adjustment Screws.
.
.
Please be noted that the Mirror Hangers are fully
adjustable allowing for easy leveling.
STEP 8:
a With the help of another person, pass the holes on Crossbars over the Mirror Hangers so that the
Crossbars rests on the inside of the Bracket Catches.
c If needed, adjust mirror for straightness by eye or use level. Make corrections using Adjustment Screws
on Mirror Hangers.
.
.
STEP 9:
a Clean glass with household glass cleaner. Retain this sheet for future reference..
½ WIDTH
"B”
6”
C
Hanger Nail
Mirror Hanger
Adjustment
Screw
Bracket Catch
Mark "B"
Crossbar
3
”
"C”
ASSEMBLY INSTRUCTIONS
STYLE NUMBER JA43225PN, JA43225BN: