Quoizel DE8959IB Mounting instructions

Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-DE8959IB_R1
For Style DE8959IB
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
ACrossbar Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(2)B10CandelabraBasebulbs60WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses.
C
Finial
Assembly
x1
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
B
Alternate
Mounting
screw
x2
STEP 1 Remove Styrofoam-
A. Unscrew the hex coupling on the top of the Fixture Body (D) and
remove the fixture hood from the cage.
B. Remove the Styrofoam inside of the cage.
Figure 1
Fixture
Hood
Cage
RevisedDate:2017-11-23
DFixture Body
x1
Styrofoam (Remove)
Hex Coupling
D
STEP 2 Install Bulbs and Finial
Assembly
-
A. Insert bulbs onto sockets and
screw snugly into place.
B. Place the fixture hood back onto
the cage and secure with the hex
coupling. Hand tighten until
snug.
C. Remover nipple, strut member
and waterproof washer from the
finial.
D. Thread the nipple onto the hex
coupling and hand tighten until
snug. Pass the strut member and
waterproof washer over the top
end of the nipple and secure with
the finial. Hand tighten until
snug.
STEP 3 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
A
Mounting Screw
or Alternate Short
Mounting Screw
Outlet Box Screws
(not included)
Supply Wires
with Ground Wire
Outlet Box
Figure 3
Hex Coupling
Fixture
Hood
Stem
Bulb (not
supplied)
Socket
Finial
Waterproof Washer
Strut Member
Nipple
Figure 2

2of2
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
RevisedDate:2017-11-23
STEP 4 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (D) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (D) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw
or alternate short mounting screw on the Crossbar Assembly (A) by
D
Mounting Ball
A
Backplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw
Figure 4
unscrewing the preassembled hex nut and lock
washer and then screwing the mounting screws
or alternate short mounting screws in or out of
the crossbar until the correct length is achieved.
Once the backplate
and Fixture Body (D)
is secure, remove the
mounting ball and
Fixture Body (D) and
proceed to Step 5.
STEP 5 Make Wire Connections-
Wrap ground wire around green ground screw on the
crossbar, no less than 2 in from the end of the wire. Tighten
.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
A. bare or green
ches the
green ground screw
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 5
STEP 6 Install the Fixture Body-
A. Position the backplate and Fixture Body (D) onto
the Crossbar Assembly (A). Place the holes in the
backplate over the mounting screws or alternate
short mounting screws. Secure the Fixture Body
by using the mounting balls and hand tighten the
mounting balls until snug.
D
Mounting Ball
A
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
Figure 6
STEP 7 -Apply Silicone Sealer
A. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over
top of backplate and down both sides. Do not caulk the bottom of
the fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade
Caulk
Backplate
Exterior
Grade
Caulk
Figure 7
DE8959IB
FINISH: IMPERIAL BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED
UP TO THE NEAREST 1/4"
9”
17.5”
11”
21”
10”
5”
Fixture can
only be
mounted in
the direction
indicated