Quoizel Waterville WTE8411WT Mounting instructions

Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-WTE8411WT
For Style WTE8411WT
2017 QuoizelInc.
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBasebulb100WMaximumor
(1)MediumBaseVintagebulbisrecommendedbutnotsupplied.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-09-29
Package Contents
ACrossbar Assembly
x1
CFixture Body
x1
B
Alternate
Mounting screw
x2
D
Glass
Shade
x1
STEP 1 Remove the Shade Holder and Shade Cap-
A. Unlock lock balls to remove the shade holder and the shade cap from
the Fixture Body (C). Separate the shade holder from the shade cap
by unscrewing hex nuts.
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate and Fixture Body (C) onto the Crossbar Assembly (A)
and secure with mounting balls. Note: The backplate and Fixture
Body (C) should be snug against the wall and held tight with the
mounting balls. If it is not, adjust the length of the mounting screw or
alternate short mounting screw on the Crossbar Assembly (A) by
unscrewing the preassembled hex nut and lock washer and then
screwing the mounting screws or alternate short mounting screws in
or out of the crossbar until the correct length is achieved. Once the
backplate and Fixture Body (C) is secure, remove the mounting ball
and Fixture Body (C) and proceed to Step 4.
C
Mounting
Ball
A
Backplate
Hex Nut and
Lock Washer
Figure 3
Mounting Screw
or Alternate Short
Mounting Screw
C
C
Lock Ball
Hex Nut
Shade Cap
Shade Holder
Figure 1
Supply Wires
with Ground Wire
Outlet Box Screws
(not included)
Outlet
Box A
Figure 2
Mounting Screw
or Alternate Short
Mounting Screw
STEP 2 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.

2of2
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-09-29
STEP 5 Install the Fixture Body-
A. Position the backplate and Fixture Body (C) onto the Crossbar
Assembly (A). Place the holes in the backplate over the mounting
Figure 5
STEP 7 Install the Bulb and Glass Shade-
A. Insert the bulb onto the socket and screw snugly into place.
B. Attach the shade holder with Glass Shade (D) onto the Fixture Body
Figure 7
Vintage Bulb
(recommended
but not supplied)
Lock Ball
FINISH: WESTERN BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"
STEP 4 - Wire Connections
A. Wrap bare or green ground wire around green ground screw on the
crossbar, no less than 2 inches from the end of the wire. Tighten the
green ground screw.
B. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Green Ground Screw
on the Crossbar
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from Fixture
Figure 4
STEP 6 Install the Shade
Holder and Shade Cap
-
A. Place the Glass Shade (D) into
the shade holder and attach
the shade cop onto the top
edge of the Glass Shade (D).
Secure by threading hex nuts
onto bolts on the shade holder.
Tighten gently until snug.
Hex Nut Shade
Cap
Shade
Holder
D
Figure 6
Bolt
Bolt
D
Shade
Holder
STEP 8 Apply Silicone Sealer-
A. Make sure the exterior wall surface and fixture backplate are free of
dirt before applying caulk. Using exterior grade caulk, caulk over top
of backplate and down both sides. Do not caulk the bottom of the
fixture backplate to ensure proper moisture drainage.
Your fixture is now assembled and ready to use. Enjoy!
Exterior
Grade Caulk
Backplate
Figure 8
Exterior
Grade Caulk
screws or alternate
short mounting
screws. Secure the
Fixture Body by using
the mounting balls
and hand tighten the
mounting balls until
snug. C
Mounting
Ball
A
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
(C). Pass the bolts on
the shade holder back
through the holes on the
Fixture Body (C) and
secure with previously
removed lock balls.
Hand tighten until snug.
Fixture can
only be
mounted in
the direction
indicated
6” Dia.
12.25”
11”
10.75”
6”
WTE8411WT