Package Contents
Warnings and Cautions
1of2
Assembly Instruction Sheet #IS-RPT8407PN
For Style RPT8407PN
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
ACrossbar Assembly
x1
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)A19MediumBasebulb100WMaximum.
20-30minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtoensureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssembly Time:
Preparation:
Fixturecanonlybemountedinthedirectionindicatedonpage2.
ToolsRequired:Flatheadscrewdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
CFixture Body
x1
B
Alternate
Mounting screw
x2
GND
Figure 1
STEP 1 Remove Styrofoam inside
of the Cage
-
A. Unscrew lock screws on the fixture
hood by using screwdrivers and
remove the cage from the fixture
body.
B. Carefully remove the Styrofoam
inside of the cage.
Lock
Screw
Styrofoam
Cage
Fixture Body
2017 QuoizelInc.
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
ReleasedDate:2017-07-06
STEP 2 Installing the Crossbar Assembly-
A. Pass the supply wires through the Crossbar Assembly (A). Attach
the Crossbar Assembly (A) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure the Crossbar Assembly (A)
with Outlet Box Screws (not included). Tighten until snug
Note: Use the Alternate Shorter Mounting Screw (B) if your
installation requires a shorter mounting screw.
.
Outlet Box Screws
(not included)
Outlet
Box
Mounting Screw
or Alternate Short
Mounting Screw
Supply Wires
with Ground Wire
A
STEP 3 Test Fit the Backplate to the Crossbar Assembly-
A. Remove the mounting balls from the Crossbar Assembly (A). Place
the backplate onto the Crossbar Assembly (A) and secure with
mounting balls. Note: The backplate should be snug against the wall
and held tight with the mounting balls. If it is not, adjust the length of
the mounting screw or alternate short mounting screw on the
Crossbar Assembly (A) by unscrewing the preassembled hex nut
and lock washer and then screwing the mounting screws or alternate
short mounting screws in or out of the crossbar until the correct
length is achieved. Once the backplate is secure, remove the
mounting ball and backplate and proceed to Step 4.
Mounting Ball
ABackplate
Hex Nut and
Lock Washer
Mounting Screw
or Alternate Short
Mounting Screw Figure 3
Figure 2
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 4
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
