Quoizel Zephyr ZP8418MD Mounting instructions

1of2
6 CORPORATE PARKWAY
GOOSE CREEK SC 29445
www quoizel com
,.
..
Assembly Instruction Sheet #IS-ZP8418MD_R1
For Style ZP8418MD
Pleasegoto forproductcleaningtips.Gotothe selection.
(1)T4MiniCandelabraBulb50WMaximum(supplied).
30-45minutes
Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare
present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement
parts.
www.quoizel.com Care + Maintenance
LightSource:
EstimatedAssemblyTime:
Preparation:
ToolsRequired: Flathead screwdriver,Phillipsscrewdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal.
A
Fixture Body
x1
B
Package Contents
Hardware Contents
AA
BB
CC
Crossbar
x1
Lock Washer
x2
Hex Nut
x2
DD Mounting Screw
x2
EE Mounting Ball
x2
Figure 2
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
FF
Alternate
Mounting screw
x2
2016 QuoizelInc. RevisedDate:2016-11-10
T4 Mini Bulb
x1
Glass Panel
Lock Screw with Rubber Washer
STEP 1 Remove Glass Panel from Fixture Body-
A. Locate the Fixture Body (B) onto a flat work surface. Loose Lock
Screws with Rubber Washers and then remove them and Glass
Panel from the Fixture Body (B).
B
Figure 1
STEP 2 -Attach Mounting Screws, Lock Washers and Hex Nuts to
Crossbar
A. Line up a set of holes on the Crossbar (AA) and Holes on the
Backplate of Fixture Body (B). Thread Mounting Screws (DD) or
Alternate Short Mounting Screws (FF) into the holes on the
Crossbar (AA). Pass Lock Washers (BB) and thread Hex Nuts (CC)
onto the Mounting Screws (DD) or Alternate Short Mounting Screws
(FF). Hand tighten until snug.
Note: Use the Alternate Shorter Mounting Screw (FF) if your
installation requires a shorter mounting screw.
AA AA
Mounting Screw
or Alternate Short
Mounting Screw
BB
CC
B
AA
Mounting Screw
or Alternate Short
Mounting Screw
Backplate
STEP 3 -Installing the Crossbar Assembly
A. Pass the supply wires through the Crossbar (AA). Attach the
Crossbar (AA) to the Outlet Box with the head of the Green Ground
Screw facing you. Secure the Crossbar Assembly (AA) with Outlet
Box Screws (not included). Tighten until snug.
Outlet Box
Outlet Box Screws
(not included)
AA
Supply Wires
with Ground Wire
Figure 3

2of2
2016 QuoizelInc. RevisedDate:2016-11-10
Thank you for purchasing a Quoizel product.
Need assistance with parts or assembly? Call Quoizel customer service at 1-800-645-3184
or visit us on-line at www.quoizel.com
STEP 4 -Test Fit the Backplate to the Crossbar Assembly
A. Place the backplate and Fixture Body (B) onto the Mounting
Screws (DD) or Alternate Short Mounting Screws (FF) and secure
with Mounting Balls (EE). Note: The backplate and Fixture Body (B)
should be snug against the wall and held tight with the Mounting
Balls (EE). If it is not, adjust the length of the Mounting Screws
(DD) or Alternate Short Mounting Screws (FF) on the Crossbar by
unscrewing the Hex Nuts (CC) and Lock Washers (BB) and then
screwing the Mounting
Screws (DD) or Alternate
Short Mounting Screws (FF)
in or out of the Crossbar
(AA) until the correct length
is achieved. Once the
backplate and Fixture Body
(B) is secure, remove the
Mounting Balls (EE) and
Fixture Body (B) and
proceed to Step 5.
9” 7”
18”
B
Backplate
Hex Nut and
Lock Washer
Figure 4
Mounting Screw
or Alternate Short
Mounting Screw
EE
AA
STEP 5 -Attach the Lanyard
A. The purpose of the lanyard is
to provide a means to support
the fixture hands free from the
junction box while connecting
the electrical wires.
B.TurntheButtonStopsoitmay
be inserted into a Crossbar
slot. Make sure the Button
Stop is completely inside the
Crossbar. Slowly release the
fixturetomakesureitis
supported by the Button Stop.
Proceed to the wiring steps in
the next step. Once you are
complete with the wiring, the
Lanyard will push into the
junction box when the fixture is
placed for final mounting. Figure 5
Crossbar
Button
Stop
Lanyard
Slot
B
STEP 6 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. Twist connectors until wires are tightly joined together.
Wrap each connection with approved electrical tape and carefully
stuff all the connected wires into the Outlet Box.
Figure 6
White wire
from outlet box White wire
from fixture
Black wire from
outlet box (or Red)
Black wire
from fixture
Bare, or Green
Ground wire
from outlet box
Ground wire
from fixture
Bare, or Green
Ground wire
from outlet box
OR
Ground wire
from fixture
Green Ground Screw
on the Crossbar
STEP 7 Install the Fixture
Body
-
A. Position the backplate and
Fixture Body (B) onto the
. Secure the
by using the Mounting
Balls (EE) and hand tighten
the
until snug.
Mounting Screws (DD) or
Alternate Short Mounting
Screws (FF)
backplate and Fixture Body
(B)
Mounting Balls (EE)
Figure 7
B
Backplate
Mounting Screw
or Alternate Short
Mounting Screw
EE
AA
STEP 8 -Install the Bulb
A. Insert the supplied Bulb (A) onto
socket and push snugly into place.
B. Place the glass panel back onto the
Fixture Body (B) and secure with
lock screws with rubber washers.
Your fixture is now assembled and
ready to use. Enjoy!
B
A
Figure 8
Glass Panel
Lock Screw with
Rubber Washer
ZP8418MD
FINISH: MUTED BRONZE
NOTE: ALL DIMENSIONS ARE ROUNDED UP
TO THE NEAREST 1/4"