R82 Toucan User manual

toucan
© 2010 R82 A/S. All rights reserved.
The R82 logo and the Toucan are registered trademarks of R82 A/S.
TM
07.2011 - rev. 003
English user manual
G
B

2
G
B
GB CONTENTS
Safety ................................................................................ 4
Warranty ............................................................................ 4
Tools .................................................................................. 4
Maintenance ...................................................................... 4
Ready for use .................................................................... 5
Angling of the centre bar ................................................... 6
Wheel locks ....................................................................... 6
t-tool................................................................................... 6
Mounting and adjustment of the foot plate ........................ 7
Mounting and adjustment of individual foot supports ........ 8
Extra chest infill cushion .................................................... 8
Mounting of flip-up sandals / heel supports ....................... 9
Knee supports ................................................................... 9
Hinged knee supports...................................................... 10
Abdominal support........................................................... 10
Hip support, rear .............................................................. 11
Head support ................................................................... 12
Hip support, front ............................................................. 13
Hip supports de-rotational ............................................... 13
Tray with bowl .................................................................. 14
Armrest for tray ................................................................ 14
Chest support .................................................................. 15
"Pony" chest support ....................................................... 15
Sliding Extension for centre bar....................................... 16
Product identification ....................................................... 17
Measurements ................................................................. 18
Technical data.................................................................. 19
Producer .......................................................................... 19
Troubleshooting ............................................................... 19
Distributor ........................................................................ 19
Care and maintenance .................................................... 20

3
G
B
GB TOUCAN
The Toucan is a modern standing frame providing users the possibility of standing
and having weight bearing through their feet. It is important to have the possibility
to stand at an early age. Further it is not about standing for a long time but about
standing often.
This user manual is a guide to assist in gaining the full benefits of the options of-
fered by the Toucan. Therefore, we recommend that you read this manual before
using the frame.

4
G
B
GB
GB
GB
GB
SAFETY
The Toucan conforms to the CE-mark. This certifies that it meets all relevant Euro-
pean safety requirements.
The durability of this product is 5 years when it is used on a daily basis and regulal
maintanance has been performed. Hereafter the product must be renovated (by
R82 personnel) to extend the lifetime.
Remove the CE-mark, when re-building the product or when using other than
original R82 spare parts and fittings.
Check the strap before every use and replace any worn out parts before using
this product.
Never leave your child unattended in this product. Ensure constant supervision
by an adult. Incorrect use of the product, may cause serious injury to the user.
Ensure that the belt is securely fixed to the frame before every use.
WARRANTY
R82 offers a 2-year warranty against defects in workmanship and materials and a
5-year warranty on breakage of the metal frame caused by defects in welds. The war-
ranty would be adversely affected if the customer’s responsibility of servicing and/or
daily maintenance is not carried out according to the guidelines and intervals prescribed
by the supplier and/or stated in the manual. For further information, we refer to the
R82 homepage/download. The warranty can only be sustained if the R82 product is
in use in the same country where it was purchased and if the product can be identi-
fied by the serial number. The warranty does not cover accidental damage, including
damage caused by misuse or neglect. The warranty does not extend to non-durable
parts, which are subject to normal wear and tear and need periodic replacement.
The warranty is null and void if non-original R82 parts/accessories are used, or if the
product is repaired or altered by anyone other than an authorised R82 representative
or by trained personnel officially recognised by R82 for repair and maintenance of
R82 products. R82 reserves the right to inspect the product being claimed for and the
relevant documentation before agreeing to the warranty claim, and to decide upon
whether to replace or repair the defective product. It is the customer’s responsibility
to return the item being claimed for under warranty to the address of purchase. The
warranty is given by R82 or, subsequently, an R82 dealer.
TOOLS
Tools are delivered with the Toucan: 5 & 6 mm allenkey and 2 pcs. T-tools. Theese
tools are used to perform some of the adjustments described in this manual.
MAINTENANCE
Clean the standing frame on a regular basis.
Do not use any cleaning materials containing chlorine or methylated spirit.
Adjustments which are not described in this manual, must only be made by
authorized R82 personnel.

5
B
A
C
D
F
EF
G
B
GB READY FOR USE
The Toucan is delivered in parts and without
accessories so as to take up as little room as
possible during transportation. To assemble
your Toucan ready for use, please follow the
description below.
Size 1+2+3:
Fasten the spindle for angle adjustment the fol-
lowing way:
* Tip the centre bar (A) into the vertical position
* Turn the handle (B) to fit the holes in both cen-
tre bar and fitting (C) into the same level.
* Push the square plate in the centre bar up
and secure it beneath the fitting (C).
* Mount the bolt with the washer and fasten
into the square plate in the centre bar using
the enclosed 6 mm Allen key.
Size 4+5:
The centre bar has been dismounted before
shipment to make the Toucan size 4+5 take up
as little room as possible during transportation.
Follow the description below to mount the centre
bar correctly.
* Dismount and keep screws and washers (D)
* Mount the centre bar on the square fittings on
the centre plate of the frame (E)
* Fasten the screws (F) through the holes in
the centre plate and into the centre bar.
* Then follow the description descriped above
for size 1+2+3.
Check and re-tighten the bolts on a regular
basis.
The Toucan is now ready to receive any acces-
sories ordered.
Do not place a user in the Toucan if it has
been standing in/exposed to the sun. For
the safety and comfort of the user the
Toucan must be moved away from the sun
and allowed to cool before use.

6
B
B
A
A
C
A
G
B
GB
GB
ANGLING OF THE
CENTRE BAR
The angle of the centre bar / standing frame is
adjustable either with or without a user in the
Toucan.
* Pull out the security lock "(A)" to be able to
angle the centre bar / standing frame. Turn the
handle (B) to desired angle. Let go of the se-
curity lock to maintain the desired position.
The Toucan size 4+5 is equipped with a small
ring (C). This ring allows a maximum angle
adjustment of 20°.
WHEEL LOCKS
The Toucan is equipped with wheel locks on all
4 wheels. Lock the wheels individually pushing
down the button (A). Un-lock the wheels by re-
leasing the red button (B).
The wheels should be locked when in use.
We do not recommend locking the wheels
when stored for extended periods.
T-TOOL
The T-tool (A) helps to maintain the square pla-
tes in the slot of the center bar, when mounting or
adjusting eg. knee supports, hip support etc.
Insert tool into slot, twist 90° and tip down to
support the plate.
GB

7
C
D
C
A
B
G
B
GB MOUNTING AND
ADJUSTMENT OF
THE FOOT PLATE
Follow the description below to mount the foot
plate correctly. We recommend dismounting
the square plates (A) from the foot plate before
mounting.
Tip!
In general we recommend that you mount all
accessories from the top of the centre bar which
is why the lower accessories must be mounted
first.
* Dismount the top part (B) in the top of the cen-
tre bar using the enclosed 5 mm allen key.
* The square plates (A) from the foot plate
should be mounted in the slots on the centre
bar. Let them slide all the way down the centre
bar.
* Mount the foot plate onto the square plates
in the centre bar using the enclosed bolt (C)
and the 6 mm Allen key.
Turn the handle (D) to angle adjust the foot
plate.
Loosen the bolts (C) in both sides of the centre
bar and height adjust the foot plate. Fasten the
bolts in the desired position.

8
A
E
A
A
B
2
1
3
B
C
D
G
B
GB MOUNTING AND
ADJUSTMENT OF
INDIVIDUAL FOOT
SUPPORTS
Follow the description below to mount the
foot supports correctly. The foot supports are
mounted seperately and can be adjusted indi-
vidually.
* The square plates mounted on the foot sup-
port, should be mounted in the slot on the
centre bar as for the foot plate.
* Adjust the height and fasten the screw (A)
using the 6 mm Allen key.
Tip!
In general we recommend to mount all acces-
sories from the top of the centre bar which is why
the lower accessories must be mounted first.
Loosen the screws (B) to adjust the height and
angle of the foot supports. Adjust the foot plate
sidewise (C) and in depth (D). Loosen the screws
(E) to adjust the angle of the foot plate. Make
sure to fasten the screws (D) and (E) in the re-
commend order; 1, 2, 3.
Make sure that all screws are fastened
securely before use.
EXTRA CHEST
INFILL CUSHION
Move the cushions on the chest support or the
hip support to the side by loosening the bolts (A)
to make room for the extra cushion.
Place the extra cushion in the middle between
the cushions, and tighten the bolts (A) and (B).
Can be mounted on the chest support and
hip supports size 2 and 3.
GB

9
C
C
A
A
B
A
B
B
C
D
G
B
GB MOUNTING OF FLIP-
UP SANDALS / HEEL
SUPPORTS
Follow the description below to mount the flip-up
sandals / heel supports correctly.
* Place the enclosed bolt (A) in the slot from the
top of the footplate/heel support and fasten
with the fingerscrew (B).
* The flip-up sandal / heel support can be adju-
sted forward or/and backward depending on
the desired placement (C). Fasten the finger-
screw beneath the foot plate in the desired
position.
KNEE SUPPORTS
Follow the description below to mount the
knee supports correctly. The knee supports
are mounted seperately and can be adjusted
individually.
* The square plates on the knee support should
be mounted in the slot on the centre bar.
* Adjust the knee support to the desired height
and fasten (A) using the enclosed 6 mm allen
key.
Make sure that the fitting (B) is in the
vertical position when the knee support is
mounted. (not for size 1).
* Loosen the screw (C) and adjust the angle of the
foot support. Fasten in the desired position.
* Loosen the screw (D) and adjust the knee
supports sidewise.
GB

10
A
C
D
E
B
B
A
G
B
GB HINGED KNEE
SUPPORTS
Follow the description below to mount the hin-
ged knee supports correctly. The knee supports
are mounted seperately and can be adjusted
individually.
* The square plates on the knee support should
be mounted in the slot on the centre bar.
* Adjust the knee support to the desired height
and fasten (A) using the enclosed 6 mm allen
key.
Make sure that the fitting (B) is in vertical
position when the knee support is mounted.
(not for size 1).
* Loosen the screw (C) and adjust the angle of the
foot support. Fasten in the desired position.
* Loosen the screw (D) to angle the support
around the knee. Use the enclosed 5 mm
allen key.
* Loosen the screw (E) and adjust the knee
supports sidewise.
ABDOMINAL
SUPPORT
Follow the description below to mount the ab-
dominal support correctly.
* Mount the two square plates in the slots on
both sides of the centre bar.
* Mount bolts (A) in the upper square plates and
fasten lightly. Do not fasten completly before
the four bolts have been placed correctly.
* Mount bolts (B) in the lower square plates.
Move the bolts (A) + (B) and plates upwards
until they fit into the fitting from the abdominal
support. Now fasten all four bolts securely
using the enclosed 6 mm allen key.
GB

11
DE
G
A
B
C
H
G
B
HIP SUPPORT,
REAR
Follow the description below to mount the hip
support correctly:
* Mount two square plates in the slots on both
sides of the centre bar.
* Mount bolts (A) in the upper square plates
and fasten at the desired height using the
enclosed 6 mm allen key.
Be aware that the height of the top square
plates is the same on both sides of the
centre bar. If not, adjust into position.
* Mount the fitting from the hip support on the
top bolts.
* Mount bolts (B) in the lower square plates.
Move the bolts and plates upwards until they
fit into the fitting from the hip support. Fasten
all bolts securely using the enclosed 6 mm
allen key.
* Fasten the fingerscrew (C) through the hole
in the fitting to secure the fitting from the hip
support to the centre bar.
* Pull out (unlock) the security lock (D) and
loosen the handle (E) to adjust the hip sup-
ports in depth. Adjust into desired position,
push in (lock) the security lock and fasten the
handle.
Make sure the security lock is pushed in
(locked) after adjustment.
* Loosen the handle (G) to adjust the hip sup-
port in height.
Use the enclosed 6 mm allen key to loosen the
bolts (H) and adjust the supports individually in
height and width. (not possible for size 1)
Make sure the fingerscrew (C) is fastened
before use.
GB

12
F
H
G
A
B
C
D
E
G
B
HEAD SUPPORT
Follow the description below to mount the head
support correctly.
Either back support or hip supports (rear)
must be mounted to be able to mount a
head support on the Toucan
* Mount the head support bar on the fitting
from the back support/hip supports (rear) and
fasten with the enclosed 4 mm Allen key (A).
* Loosen the handle (B) to adjust the angle of
the head support bar.
* Loosen the handle (C) to adjust the height of
the head support.
* When a lower setting of the head support is
needed, the fitting on the back- / hipsupport
can be replaced with a new fitting and bar (D).
* Loosen the screw (E) to adjust the angle of
the head support bar.
* Use the enclosed 5 mm Allen key to loosen
the screws (F) and adjust the head support.
Loosen the screw (G) to angle the head sup-
port. Loosen the screw (H) to adjust the head
support sidewise.
GB

13
C
B
C
D
B
A
A
G
B
HIP SUPPORTS DE-
ROTATIONAL
Follow the description below to mount the dero-
tational hip supports correctly:
* Dismount the two fittings (A) from the de-ro-
tational hip supports.
* Mount the fittings on both sides of the centre
bar. Fasten the screws (B) in the desired posi-
tion. The possiblity of vertical rotational adjust
is available before the screws are fastened
completely.
* Mount the hip support on the fitting (C). Fasten
in the desired angle.
* Loosen the screws (D) to adjust the hip sup-
port for width and in height. Fasten all screws
in the desired position.
HIP SUPPORT, FRONT
Follow the description below to mount the hip
support correctly.
* Mount the two square plates in the slots on
both sides of the centre bar.
* Mount bolts (A) in the upper square plates and
fasten lightly. Do not fasten completly before
the four bolts have been placed correctly.
* Mount bolts (B) in the lower square plates.
Move the bolts (A) + (B) and plates upwards
until they fit into the fitting from the hip sup-
port. Now fasten all four bolts securely using
the enclosed 6 mm allen key.
* Loosen the bolts (C) and adjust the hip sup-
ports in depth. Fasten the bolts in the desired
position.
GB
GB

14
A
B
C
D
A
G
B
TRAY WITH BOWL
Follow the description below to mount the tray
correctly.
* Loosen the screws (A) to separate the fit-
ting.
* Place the lower part of the fitting (A) below
the frame and make sure the screws already
mounted on the frame fit into the fitting*.
* Mount the tray/tube with the top fitting on the
frame and fasten with the provided screws.
Fasten the screws with a screwdriver. Mount
the tubes on both sides of the frame.
* Fasten the tray by mounting the chest support
through the bar on the tray and the centre bar.
Fasten with the handles (C).
* Loosen the fingerscrews (D) to adjust the tray
in height.
* Place the plate on the tray to cover the
bowl.
ARMREST FOR
TRAY
Follow the description below to mount the arm-
rest for tray correctly.
* Mount the armrests in the cross tube fitting
beneath the tray and fasten with the illustrated
screws and 4 mm Allen key. (A)
GB
GB
* Plastic tables
* Wooden tables

15
C
D
A
B
G
B
CHEST SUPPORT
We recommend to mount the chest support as
the final equipment. Follow the description below
to mount the chest support correctly:
* Mount the top part (A) in the top of the centre
bar and fasten with the enclosed 5 mm allen
key.
* Mount the chest support in the hole in the
centre bar and fasten with the handle (B).
* Loosen the screws (C) and adjust the chest
support sidewise and in height. Fasten all
screws in the desired position. (not possible
for size 1)
Max. height! (D)
The max. height indication on the chest
support bar must not go any higher than
the top of the centre bar - not the top of any
other extra bars from e.g. the tray.
GB
"PONY" CHEST
SUPPORT
The "Pony" chest support is mounted in the
same way as the standard chest support
(Mentioned above).
GB

16
A
A
G
B
SLIDING
EXTENSION FOR
CENTRE BAR
Follow the description below to mount a sliding
extension on the centre bar.
* To be able to mount the extension part and
the centre bar all together, the plast covers
need to be removed. Use the 5 mm Allen key
to dismount the hubs.
* Accessories can now be mounted in both the
centre bar and the extension part.
Mount the chest support bar from the top and
down through the extension part and the centre
bar. Fasten with the handles (A).
GB

17
A
B
Dato: 31-01-02 Belast: kg
SN: 0840-01-111878-001
Varenr: 880003
5707292 134158
Parallelvej 3
DK-8751 Gedved
B
A
G
B
GB PRODUCT
IDENTIFICATION
A) Serial number
The label is placed on the underside of the
frame to the left.
B) Manufacturer
The label is placed on the innerside by the
left rear wheel.

18
I1
I2
a1a1a1a1a1a1a1a1a1
a2
H G
56 (21¾”) 63 (24½”) 63 (24½”) 70 (27¼") 70 (27¼")
75 (29¼”) 88 (34¼”) 88 (34¼”) 111 (43¼") 111 (43¼")
67-87 (26¼-34”) 72-101 (28-39½”) 97-123 (37¾-48”) 104-134 (40½-52¼") 124-154
34-70 (13¼-27¼”) 54-90 (21-35”) 74-110 (29-43”) 91-121 (35½-47¼") 111-141 (43¼-55")
45 (17½") 50 (19½") 70 (27½") 80 (31¼") 100 (39")
6 (2½”) 6 (2½”) 6 (2½”) 6 (2½”) 6 (2½”)
0 to +30° 0 to +30° 0 to +30° 0 to +20° 0 to +20°
+15° to -10° +15° to -10° +15° to -10° +15° to -10° +15° to -10°
7,5 kg (16,5 lb) 8,5 kg (19 lb) 9 kg (20 lb) 10,5 kg (23 lb) 10,75 kg (24 lb)
30 kg (66 lb) 40 kg (88 lb) 50 kg (110 lb) 60 kg (132 lb) 70 kg (154 lb)
G
B
GB MEASUREMENTS
Size 1 Size 2 Size 3 Size 4 Size 5
cm (inch) cm (inch) cm (inch) cm (inch) cm (inch)
Width (G)
Length (H)
Total height (I1)
Height from foot to chest (I2)
Length, centre bar
From floor to footplate
Angle of the centre bar (a1)
Angle of the foot plate (a2)
Weight
Max. load/user weight

19
G
B
GB
GB PRODUCER
R82 A/S
Parallelvej 3
8751 Gedved
Denmark
DISTRIBUTOR
GB
Please find your distributor on www.R82.com
TECHNICAL DATA
Frame: Powder laquered aluminium tubes
Plastic parts: Fiber glass strengthened nylon
Upholstery: PUR (Polyurethane)
Problem*
The standing frame is hard
to move/push/turn
The angle winding mecha-
nism is not working
The product seems loose
* The user may experience several of these problems in a standing frame that is incorrectly
adjusted or is being used incorrectly.
Solution
- Check that all brakes have been released.
- Check if all front forks are turnable - If not, contact your dealer
- Check if the security lock has been released. If the winding me-
chanism is still not working, contact your dealer.
- Check if all screws and bolts hasve been fastened securely
- Adjust the distance between the tires and the brake
TROUBLESHOOTING
This product is multi-adjustable and must only be set up by authorized personnel (e.g. thera-
pists).
GB

20
G
B
CARE AND MAINTENANCE
PUR
All parts made of PU material must be wiped off with a cloth frequently.
WHEELS/BRAKES
Ball bearings: The ball bearings require no maintenance.
Clean the wheels frequently to make them run more smoothly and make the brakes function
optimally. NO lubricating oil is required around the brakes. Wheels that are worn out must be
replaced.
FRAME
Tighten all screws on the frame on a regular basis, especially when the Toucan has been
adjusted. Also, it is important to keep the frame clean, both for the users comfort and the
longevity of the standing frame. Wash the frame with car shampoo or washing up liquid. If the
Toucan is especially dirty, a grease remover may be used.
INSPECTION
It is important to tighten all screws on the standing frame on a regular basis. All screws which
secure the accessories must be checked, at least once a month. To avoid sharp edges, it is
important to check all rail-ends have end caps. Also, it is important to check for any cracks or
faults in the frame, PVC parts, etc.
REPAIR
If there is a problem with your Toucan you should contact your dealer at once. Defective
frames should not be used. If your standing frame needs reconditioning or repair, only origi-
nal R82 parts may be used. Accessories or available spare parts which are broken can be
forwarded to R82 for repair. If there is a problem with any basic parts, the whole frame must
be returned to R82 for repair. R82 will not be held responsible for damage or injury caused by
use of non-original parts or repairs made by non-authorised R82 personnel.
GB