RACEceiver LapCeiver User manual

BATTERY CARE
Battery life is between 28-30 days on a new
alkaline battery.
1. Remove battery from unit when
storing scanner. Corrosion may take place if
battery is left in unit for long periods of time.
2. Keep battery contact surfaces and
compartment clean.
3. Store batteries in a dry place at normal
temperature.
4. Never attempt to recharge a battery unless it
is specifically marked “Rechargeable”
5. Dispose of batteries properly.
WARRANTY
Your LapCeiver™ comes with a full 3 year
warranty against manufacturer defects from
the date of purchase.
REGISTER YOUR WARRANTY ONLINE
www.raceceiver.com

A Product of
Innovative Spectator Products, Inc.
742 Main St.
Gainesville, Georgia 30501
1-866-301-RACE (7223)
www.raceceiver.com
A Product of
Innovative Spectator Products, Inc.
742 Main St.
Gainesville, Georgia 30501
1-866-301-RACE (7223)
www.raceceiver.com
Congratulations on your purchase of
The LapCeiver™.
Now you can have your lap times in the palm of
your hand. We are pleased to be the innovator of
this new tool for your racing team. We look forward
to years of serving you with a corporate mission
built on customer service, value and innovation.

RACEceiver™ LapCeiver
The latest development in the RACEceiver product
line is the LapCeiver. The LapCeiver is designed
for the driver or crew member who wants to get
their lap times wirelessly in the palm of their hand.
.
The LapCeiver works in conjunction with the
RACEceiver transponder scoring system:
•It receives all green flag lap times.
•The LapCeiver can store 500 laps in each of
its 5 memory banks for a total of 2500 laps.
•Displays lap times in minutes, seconds and
thousands of seconds.
•The LapCeiver comes with a USB cable and
you can download software from our
website (www.raceceiver.com) that lets you
upload your lap times from the LapCeiver to
your computer.
(◄) Left Yellow Arrow
(►) Right Yellow Arrow
(▲) Up White Button
(▼) Down White Button
“BLUE” Button
Use to scroll up Memory banks
“RED” Button
On/Off Hold for 3 seconds

OPERATING INSTRUCTIONS
INSTALLING BATTERY
1. Unlock Battery Cover
2. Insert Battery
3. Lock Battery Cover
Unit may be turned ON/OFF by holding RED button
for approximately 3 seconds. After the unit is turned
off, the display with show ‘OFF’ for 60 seconds
Information stored in memory locations is not lost when
battery is removed or dead.
LOAD TRANSPONDER ID
This is the Serial Number of the Transponder that is on the car
you are monitoring.
1. Press Up arrow and down arrow (▲▼) at the
same time and it goes to ID code change mode.
2. In the ID code change mode, up (▲) arrow
selects the digits and down (▼) arrow selects 0-9
numbers.
3. Press Up arrow and down arrow (▲▼) at the
same time and then it goes back to the Lap mode.
Note: You can program just 0 and 1 at the first digit
of the transponder I D.
CHANGE MEMORY BANKS
The Memory Bank number is displayed in the upper right
corner of the display . When ‘memory’ is blinking that
memory bank is locked.
Press blue button and you can select 1- 5
memory banks.
LAP DATA DISPLAY
Press Down arrow (▼) or up arrow (▲) to see the
lap data received.
DELETE OR CLEAR MEMORY BANK
Select the memory bank you want to delete or clear
and press and hold up (▲) and left (◄) arrow
buttons for 2 seconds.
Note : Delete all or individual lap data delete is not
available.

LOCK/UNLOCK
TRANSPONDER ID
Insures that the Transponder ID does not get changed until
you change it!
1. Select the ID code you want to lock and then
press blue ( -) and left (◄)arrow. 'ID code' will be
blinking.
2. To unlock the ID code, press blue ( -) and right
(►) arrow while the 'ID code' is blinking. It stops
blinking and unlocks the ID code.
LOCK/UNLOCK
MEMORY BANK
Insures that the data in a memory bank does not get deleted
until you want to delete it.
1. Select the memory bank you want to lock and
then press blue (-) and left (◄)arrow. 'Memory'
will be blinking.
2. To unlock the memory bank, press blue ( -) and
right (►) arrow while the Memory is blinking. It
stops blinking and unlocks the memory bank.
Visit our website (www.raceceiver.com) to get your free
software so you can upload your lap times to your
computer.
LAPCEIVER PC PROGRAM
1. Connect the LapCeiver to your computer by
using UAJ100 (this cable was included with your
LapCeiver purchase). 'USb' will be displayed on
the screen.
2. Open the PC program. The Com Status should
be green.
Note: If the Com Status is still black, you should
check the com port on your computer.
3. Click read and then 'Data Read' window will
appear. Next 'Data Read OK!' window will appear.
4. Click the window and all data should go to your
PC.
5. To program ID code, click ' SYSTEM' and then
'ID Code Read/Write'. Now you can read and
write the ID code.

TROUBLESHOOTING AND
FREQUENTLY ASKED
QUESTIONS
1.Screen seems to be flashing
This is normal. This is the battery saver mode. When
unit is hot or in direct sun light it becomes more
visible.
2. Can I take this unit to the local tracks and be able
to use it?
If the track uses a compatible Timing & Scoring
System and they have a LapCeiver Transmitter
working your laptimes will be sent automatically to
your LapCeiver.
3.