rada Outlook 1621.099 User manual

1
Quick Install Guide
Rada Outlook

2
Caution! Assemble/install only as shown.
Warning! Mains electrical connection.
Isolate from mains electricity.
Check for water leaks.
Not suitable for high humidity or water condensation.
For full instructions, see Product Manuals on USB or at www.radacontrols.com
1621.117
1

3
The primary function of this product is to deliver water consistently at a desired
temperature. This requires that:
1. It is installed, commissioned, operated and maintained in accordance with the
recommendations given in the Product Manuals.
2. Periodic attention is given, as necessary, to maintain the product in good
functional order. Recommended guidelines are given in the PLANNED
MAINTENANCE section of the Rada Outlook Product Manual, on the USB
supplied or available at www.radacontrols.com
3.
protection provided by the equipment may become impaired.
4. This product must be provided with means for local disconnection that is
regulations. This MUST be a double pole switch which has at lease 3mm contact
separation in each pole.
5. The electrical installation must comply with BS 7671 (commonly referred to as
the IEE Wiring Regulations) and all relevant building regulations, or any particular
devices to improve the level of safety however, in keeping with every other mechanism
it cannot be considered as being functionally infallible.
Where chlorine disinfection is practised, DO NOT
50 mg/l (ppm) in water, per one hour dwell time. Such procedures must be conducted
strictly in accordance with the information supplied with the disinfectant and with all
relevant Guidelines/Approved Codes of Practice.
of data, or any indirect or consequential loss arising out of the customer's use of Rada
Outlook. The customer shall be solely responsible for the independent backup of all
data/information stored on Rada Outlook. Notwithstanding the foregoing, none of the
SAFETY : WARNINGS

4
Standards and Approvals
complies with all relevant directives for CE marking.
General
Pollution Degree
Protection
Connections Flat face union connections
Installation Environment Suitable for indoor use only
Pressures
800kPa (8 bar)
100kPa (1 bar)
performance.
Minimum Flow Rate Per Outlet
Temperatures
38°C
38°C
Programmable Range
from Hot Supply
Optimum Thermostatic
Control Range
Cold Water Range
Hot Water Range
Temperature Stability ± 1°C at recommended supply conditions
Ambient Temperature
Electrical
Power Supply
PIR Sensor
Hand Sensors
Hand Sensors
Power Input
PIR Sensor (not included)
Power Input
Power Output
closed
It should be possible to link more than one sensor together to increase the area covered. This will be done by connecting
the relay contacts in series and linking the connected contacts to the Outlook sensor input.
*
SPECIFICATION
—
…
—
…

5
Outlets 1 -6
Type Shower
Mode Timed
Run Time 30 seconds
Duty Flush Disabled
Pump Disabled
Fan Disabled
Number of Outlets for Fan 1
Fan Run On Time 5 seconds
Duty Flush
Flush Type Standard
Flush Interval 3 days
Scheduled Flush Time
Flush Temperature 38 °C
1 minute
Flush Duration
Mixer Valve Settings
Setpoint 38 °C
Minimum Setpoint 30 °C
Thermal Disinfection
Type Standard
1 minute
Target Disinfection Time 5 minutes
Disinfection Timeout 10 minutes
Target Temperature 60 °C
Default Settings
settings can be changed using the .
Note! The internal clock does not update automatically for summer/winter time.

6
1
1621.099

7
1621.112
1621.085
1621.136 / 1621.132 / 1621.137

8

9
1. Sensor Box.
2.
3. Key Switch (optional). To disable the system during cleaning/maintenance.
4. PIR Sensor (optional). Required for using the disinfection feature.
5. Shower or Basin Outlets (up to 6).
6. Hand Sensors (up to 6).
(Infrared sensors shown.)
7. Water Outlets (up to 6).
(See
8. Water Supplies. (See table for temperature and pressure values)
9. Mixer Valve.
10. (See table for input/output values)
11.

10
All dimensions are total wire lengths