Radia 1015 Speed Demon User manual

Owner’s Manual:Owner’s Manual:
1015 Speed Demon1015 Speed Demon
One-Gallon Vortex Mixer
Models 0-1015-PB (110V, 60Hz, Digital Display)
0-1015-PBDL (110V, 60Hz, Digital Display with Door lock)
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Owner’s Manual:Owner’s Manual:
Red D MixRed D Mix

2
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Table of ContentsTable of Contents
Safety InformationSafety Information
1.1 Safety Precaution Labels
1.2 Saftey Precaution Summary
IntroductionIntroduction
2.1 Application
2.2 Specifications
Unpacking & InstallUnpacking & Install
OperationOperation
4.1 Control Panel - 1015 PB
4.2 Install a Container
CleaningCleaning
1.1.
2.2.
3.3.
4.4.
5.5.
33
4
5
66
6
6
77
88
8
9
99
Trouble ShootingTrouble Shooting
Wiring DiagramWiring Diagram
7.1 1015 PB
7.2 1015 PBDL
Exploded ViewsExploded Views
8.1 PB & PBDL Electrical Assembly
8.2 PBDL Door Lock Assembly
8.3 Enclosure Components
8.4 Frame Assembly
8.5 Drive Assembly
8.6 Rotating Assembly
OrderingOrdering
Replacement Parts
WarrantyWarranty
NotesNotes
6.6.
7.7.
8.8.
9.9.
1010
1111
1111
1212
1313
13
14
15
16
17
18
1919
19
2020
2121
10.10.
11.11.

3
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
“WARNING!” indicates a hazardous situation, which, if not
avoided, could result in death or serious injury. These serious
injuries could include permanent loss of function or significant
disfigurement, disability, considerable pain and suffering,
amputations, severe burns, and loss or impairment of vision or
hearing. Take all necessary precautions to avoid unnecessary
injury.
“CAUTION!” indicates a hazardous situation, which, if not avoided,
could result in minor or moderate injury.
“NOTICE” indicates practices that do not involve physical injury
but may damage the machine.
NOTICE
1. Safety Information1. Safety Information
Review this owner’s manual and read all warning labels on the machine prior to use.
The three main safety notifications used in this manual and on the warning labels are
WARNING, CAUTION and NOTICE. They have specific meanings and indicate the potential
dangers from misuse of the machine.
Safety Information, Continued..

4
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
1.1 Safety Precaution Labels1.1 Safety Precaution Labels
Part No. 1784963
MOVING PARTS INSIDE
PARTES EN MOVIMENTO
PIE'CES EN MOVEMENT
-Do not open door until machine comes to complete stop;
moving parts inside could cause serious injury.
-No abra la puerta hasta que la marquina se detenga
completamente, las partes internas en movimiento pueden
causar heridas graves.
- Ne pas ouvrir la porte avant que la machine ne s'arrête
complètement. Pièces en mouvement à l'intérieur pourraient
provoquer des blessures graves.
WARNING
ADVERTENCIA
AVERTISSEMENT
- Machine must be properly grounded before use; improper grounding could cause electric
shock and injury.
-Disconnect power cord before servicing, cleaning or removing any cover, and follow
lockout/ tagout procedures in owner manual; failure to disconnect power could cause
electric shock and injury.
-Review Owners Manual before installing or operang.
Part No. 1780899
- La maquinaria debe ser apoyada correctamente en el suelo antes de usar, el no apoyarla
puede casuar choque elêctrico y daños.
-Desconecte la energía antes de dar mantenimiento, limpiar o quitar caulquier cubierta, y siga
los procedimientos de bloqueo/equetado del manual, Fallar en desconectar puede causar
choque eléctrico y daños.
- Revise el manual del usuario antes de instalar u operar.
- La machine doit e'tre correctement mis a' la terre avant de les ulizer mise a' la terre
incorrecte peut provoquer un choc e'lectrique et de blessure.
- De'branchez le cordon d'alimentaon avant de proce'der a'l'entreen, le neoyage
ou le retrait des capots: suivez la proce'dure d'isolaon/consignaon proce'dures
dans le manul de l'opre'rateur; E'chec de de'brancher la source d'alimentaon peut
provoquer shock and e'lectrique blessyres.
-Re'examiner le fonconnement manuel avant l'installaon.
-This machine is not explosion proof rated.
-Review product label, Material saftey Data Sheet, and HMIS rating of
materials and exposures prior to mixing to determine potentional hazards.
-Use in dry and well-ventilated environment where dust and ammable
vapors are not present; risk of physical injury exists if used in hazardous
environment.
-All containers must be properly sealed and void of leaks.
-Esta máquina no tiene la clasicatión de prueba de explosion.
-Revise la etiqueta del producto, la hoja informativa de datos de
seguridad, su clasicatión HMIS antes de mezclar y exposiciones de
materiales peligrosos para determinar los peligros potenciales.
-Use en un ambiente seco y bien ventilado donde polvo y vapores
inamables no estên presentes; Riesgo de daño sco existe si es untilizado en
un ambiente peligrosos.
-Todos los contenedores deben estar bien sellados y sin fugas.
-Cette machine n'est pas classê antidêagrant.
-Examen e'tiquette du prodiut, Fiche de dane;es de se'curite', Et
mate'riel HMIS cote et expositions, avant de faire le me'lange pour
de'terminer les risques poteniels.
-Utilisation a'sec et bien aere' environnement ou'la possie're et les
vapeurs inammables ne sont pas presents; risque de blessure physique
existe si ultilise' en environnement dangereux.
-Tous les conteneurs doivent être concenablement scellês pour èviter
les fuites.
WARNING
ADVERTENCIA
AVERTISSEMENT
Part No. 1781570
WARNING
ADVERTENCIA
AVERTISSEMENT
Safety Information, Continued..
Safety Information, Continued..

5
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
DO NOT WARNING!
DO NOT attempt to replace any damaged
electrical wire or components. Improper
replacement could result in electric shock and
serious injury. Only a qualified service representative
should attempt to repair or replace any damaged
electrical components.
Review this owner's manual before installing or
operating.
The machine must be properly grounded prior
to use. In the case of an electrical short circuit,
grounding reduces the risk of electric shock by
providing an escape wire for the electric current.
The machine’s power cord has a grounding wire
with an appropriate grounding plug. This plug must
be inserted into an electrical outlet that is properly
installed and grounded according to all local
codes and ordinances.
If you must repair or replace the power cord or plug,
DO NOT connect the grounding wire to either flat-
blade terminal. The wire with insulation having an
outer surface that is green (with or without yellow
stripes) is the grounding wire.
Check with a qualified electrician if you don’t
completely understand these grounding
instructions, or if you are not sure whether the
machine is properly grounded. DO NOT modify
the plug provided; if it won’t fit in the outlet, have
a proper outlet installed by a qualified electrician.
Disconnect the power cord before servicing,
cleaning, or removing any covers
Follow the lockout/tagout procedures of your
company.
DO NOT open the door until the machine comes to
a complete stop.
To avoid electric shock, don’t get the timer,
control panel, or wiring wet.
This machine is not explosion proof rated. All
containers must be properly sealed and void of
leaks.
Review product label, Material Safety Data
Sheet, and HMIS rating of materials prior to
mixing to determine potential hazards.
Product safety labels should be inspected
and cleaned periodically to maintain good
legibility. Replace any labels that are no
longer legible.
1.2 Safety Precaution Summary1.2 Safety Precaution Summary
DO NOT use solvent-based cleaners or
thinners.
Use in a dry and well-ventilated
environment where dust and flammable
vapors are not present.
Keep the work area free of clutter and
electrical cords.
Avoid extension cords. To minimize the risk of
improper electrical grounding, extension cords
are not recommended. If an extension cord is
unavoidable, consult a qualified electrician
to determine what type of extension cord will
satisfy the grounding, current capacity, and
other requirements of the particular situation.
Use the proper power source. Refer to the
machine data plate on the right side panel or
the section 2.1, Specifications, in this manual.
Keep customers away from the work area.
This machine should be used only by properly
trained individuals.
Clamp the can carefully to ensure that it is
held securely durning the mixing cycle.
Do not operate the machine without a can
installed.
Safety Information, Continued..
WARNING: This product may expose
you to chemicals including DEHP, which
is known to the State of California to
cause cancer. For more information, go to
www.P65Warnings.ca.gov
CAUTION!

6
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Congratulations on your purchase of the
Speed Demon 1 Vortex Mixer. This machine
is designed to accommodate single round
pint, quart, or gallon plastic or metal
containers weighing up to 15 lb. (6.8 kg). It
can also accommodate square quart cans
when used in conjunction with the optional
adapter, part no. 9784203. See section 9,
Ordering, for ordering instructions.
Understand your machine's features and
proper operation to take full advantage of
its capabilities.
Read this entire manual completely before
operating the machine. Practice installing
and removing a pail before mixing for the
first time.
Keep this manual for future reference.
Always follow all safety instructions!
Unit Size, 1015PB & PBDL: W 15 in. (38.1 cm) D
21.5 in. (54.6 cm) H 20.5 in. (52.1 cm)
Machine Weight
PB & PBDL: 76 lb. (34.5 kg)
Maximum Capacity: 15 lb. (6.8 kg)
Sizes Mixed: One pt., one qt, one gal.
Electric Service: 110 V 60 Hz
110 V Units
Machines rated at 110 V, 60 Hz are for use with
a nominal 120 V circuit.
2. Introduction2. Introduction
2.1 Application2.1 Application 2.2 Specifications2.2 Specifications
15”
21.5”
20.5”

7
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
3. Unpacking & Installation3. Unpacking & Installation
This machine was shipped fully assembled.
Before plugging in the machine or attempting
to operate it:
1. Remove all packing material.
2. Remove the locking pins from the top of
the shipping rods.
3. Push the shipping rods down far enough
to remove the retaining pins and washers
underneath the pallet.
4. Remove the shipping rods by sliding them
up through machine frame. Set aside the rods,
washers, yellow lanyard, and retaining pins
in case they are needed for shipment of the
mixer in the future.
5. Set the machine on a stable, level surface
and plug it in an appropriately grounded
outlet (see section 1.2, Safety Precaution
Summary, for grounding information).
NOTE: If the machine needs to be shipped
any time, contact RADIA to obtain the
appropriate packaging kit, part no. 6784975.
See section 9, Ordering, for ordering
information.

8
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
• Operational Indicator (A): This light is illuminated during machine operation.
• Power Switch (B): Turn the power off and on. (Note: Not used on the PBDL model)
• Digital Display (C): View programming revison and cycle time remaining.
• Ninety-Second Cycle (D): Push to set a 1:30 minute cycle. Press again to increase
the cycles in 1:30 minute increments. (Note: On the PBDL model, the door locks
until 9 seconds after the cycle completes.)
• Three-Minute Cycle (E): Push to set a 3:00 minute cycle. Press again to increase
the cycles in 3:00 minute increments. (Note: On the PBDL model, the door locks
until 9 seconds after the cycle completes.)
• Stop (F): Press to stop a cycle before the preset time expires.
(A)
4. Operation - 1015PB/PBDL4. Operation - 1015PB/PBDL
(C)
(D)
(E)
(F)
(B)
4.1 Control Panel4.1 Control Panel

9
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Always unplug the power cord before
cleaning! DO NOT get the timer, control
panel, or wiring wet.
CLEANING:
Keeping the machine clean is important for
reliable operation.
• Colorant or base paint spilled on machine
surfaces can be removed using lukewarm
water and mild detergent for water-based/
glycol colorants.
• To preserve the appearance of the
machine, do not use abrasives to clean
machine surfaces.
Figure 1 Figure 2
Figure 4
1. Open the cabinet Door
2. Load the can into the machine for mixing:
• Gallon Cans: Insert the can into the can holder.
Slip the bail handle into the clip retainers (D).
• Quart Cans: Place the can inside the quart
adapter, 6783756 (A). Set the quart can
horizontally with the lid up. (See Figure 1)
• Pint Cans: Place round pint cans vertical, with
the lid up. Close the 6783756 adapter around
the can. (See Figure 2)
• Half Pint Cans: Place the half pint can inside
the 6786133 (E) foam adapter (Optional for this
machine). Close the 6783756 adapter arount
the 6786133 foam adapter. (See figure 3)
3. For Quarts, Pints & Half pints: Insert the adapter
into the can holder .Make sure the 6783756
adapter lugs (C) are lined up with the bail retainers
and the adapter is all the way to the bottom of
the can holder (B). (See Figure 4)
4. Close the cabinet door. The mixer has a safety
switch that interrupts operation if the door is open.
5. Select the desired mix time.
If the container handle wasn’t properly
secured, press the STOP button on the control
panel.
NOTE: If colorant has been added to the paint,
be sure to reattach paint can lid tightly (using the
RADIA© Lid Press, Part No. 0-5080).
5. Cleaning5. Cleaning
Figure 3
(C)
(A)
(E)
(B)
(D)
4.2 Install a Container4.2 Install a Container

10
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
PROBLEM CAUSE REMEDY
Not connected to power source
Building ciruit breaker or fuse blown
Machine door does not make
contact with limit switch
Motor Thermal Protector Activated
Pail damaged
Faulty controller
Faulty door limit switch
Bearings worn or damaged
Connect to power source
Reset breaker or replace fuse
Adjust lever arm on the switch to make
contact with door bracket tab when
door is closed
Fix or replace pail
Contact Radia Customer Care
Contact Radia Customer Care
Contact Radia Customer Care
Machine won't operate
Excessive Vibration
Machine doesn't shut off
at end of mixing cycle
Machine doesn't shut off
when door is opened
Increasing mechincal
noise
6. Troubleshooting6. Troubleshooting
Disconnect the machine from its power source before servicing.
Allow to cool, then restart the machine
Faulty motor Contact Radia Customer Care
Contact Radia Customer Care
Worm, Damaged, or Loose
drive belt
Pail not properly seated
Feet are not level
Reset pail into holder
Adjust and level feet
Faulty controller
Faulty door limit switch
Contact Radia Customer Care
Contact Radia Customer Care

11
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
7. Wiring Diagrams7. Wiring Diagrams
7.1 1015 PB (Digital Display)7.1 1015 PB (Digital Display)
HOT/L2 - BROWN
NEUTRAL/L1 - BLUE
MOTOR 5788335
POWER SWITCH
5782445
DIGITAL DISPLAY TIMER,
VERTICAL DISPLAY
5787405
GROUND - GREEN/YELLOW
POWER CORD
5780485
MOTOR HARNESS
5784216
BLACK
GREEN
BLACK/WHITE WIRE
5786422
DOOR SWITCH
5783815
WHITE
BLACK
WHITE
GREEN
T1
NEUTRAL
T2
COM
OPERATION HARNESS
5786541
NC
WHITE
BLACK/
WHITE
ORANGE WIRE NUT 9780542
SHRINK WRAP
SHRINK WRAP
LIGHT
5787477
NO
ORANGE
WIRE NUT
9780542
I changed teh color of the outline to white so they wouldn't show in the manual

12
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
7. Wiring Diagrams7. Wiring Diagrams
7.2 1015 PBDL7.2 1015 PBDL
BLACK
N0
LIGHT
5787477
4X SHRINK WRAP
BLACK/
WHITE
NC
OPERATION HARNESS
LONG/SHORT DASH WIRES
5787629
COM
T2
T1
NEUTRAL
GREEN
WHITE
BLACK
DOOR SWITCH
5783815
MOTOR HARNESS
5784216
POWER CORD
5780485
GROUND - GREEN/YELLOW
DIGITAL DISPLAY TIMER,
W/ DOOR LOCK, VERTICAL
DISPLAY 5787617
(IN 6787622 CONTROL PANEL ASSY)
MOTOR 5788335
NEUTRAL/L1 - BLUE
HOT/L2 - BROWN
WHITE
BLACK
GREEN
3X ORANGE WIRE NUT 9780542
BLACK
ORANGE
YELLOW
BLACK/
WHITE
BROWN
RED
BLACK
YELLOW
DOOR LOCK SOLENOID
5787618
ORANGE
YELLOW
ORANGE
T3 (+) T4 (-)
WHITE
SHEET 2 IS FOR MANUAL USE, COPY THE VIEW FROM SHEET 1 AND PASTE IT ON SHEET 2 WHEN CHANGES ARE FINISHED. AN ai FILE NEEDS TO BE SAVED IN THE OWNER'S MANUAL, THEN AN .EPS FILE NEEDS TO BE CREATED FROM ADOBE ILLUSTRATOR.

13
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
11
4
3
7
5
6
2
1
10
9
10
14
6
4
9
7
8
2
1
12
13
ID Description
19786423 BOX, DIGITAL DISPLAY - 1015
29787479 PANEL, CONTROL, DIGITAL DISPLAY - 1015-PB
3
4
5
6
ID Description
7
9782603 STRAIN RELIEF 5300 PB
8
9
10
11
12
13
14
9787635 PANEL, CONTROL, DIGITAL DISPLAY - 1015-PBDL
5787405 TIMER, DIGITAL, VERTICAL, 120V
5787617 TIMER, DIGITAL, VERTICAL, 120V - 1015-PBDL
9783595 Nut, Lock, Nylon 4-40
9786232 SPACER
9781840 Nut, Keps #8-32
1787619 LABEL, DIGITAL DISPLAY - 1015-PBDL
1787763 LABEL, DIGITAL DISPLAY - 1015-PB
5782445 POWER SWITCH
5787477 LED INDICATOR, PANEL MOUNT
9102519 BUSHING,STR.RELIEF
11
3
5
Exploded Views, Continued..
8. Exploded Views8. Exploded Views
8.1 PB & PBDL Electrical Assembly8.1 PB & PBDL Electrical Assembly
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

14
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
8.2 PBDL Door Lock Assembly8.2 PBDL Door Lock Assembly
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
...Exploded Views, Continued
ID Description
1 9787630 SOLENOID BRACKET - 1015
2 5787618 SOL, 120VDC, DOOR LOCK
3 9787631 1015 DOOR LOCK LEVER
4 9787624 SPRING, .526 ID X .50 LG
ID Description
5 9787634 SCREW, HEX #10-32 X .25
6 9782004 Nut #10-24 Nylon Lock
7 9787633 SHLD BOLT, .25 DIA X 1.75
8 9783365 Screw Button 1_4 x .5
9 9787632 COTTER PIN, 1/16 X

15
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
8.3 Enclosure Components8.3 Enclosure Components
...Exploded Views, Continued

16
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
8.4 Frame Assembly8.4 Frame Assembly
...Exploded Views, Continued
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY
Exploded Views, Continued..

17
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
8.5 Drive Assembly8.5 Drive Assembly
...Exploded Views, Continued
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

18
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
...Exploded Views, Continued
8.6 Rotating Arm Assembly8.6 Rotating Arm Assembly
Exploded Views, Continued..
PART NUMBERS LISTED MAY ONLY BE AVAILABLE IN KIT FORM OR AS AN ASSEMBLY

19
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
HOW TO ORDER REPLACEMENT PARTS
Replacement parts can be ordered from Radia by telephone, fax, or email:
If you need help in determining the proper part(s) to order, please call Customer Care
at 1-800-221-1083. Always indicate the Model and Serial numbers of the machine when
ordering replacement parts.
GENERAL PARTS REPLACEMENT POLICIES
While your machine is under warranty, do not attempt on-site repair or parts replacement
without first contacting RADIA. (to protect your warranty). After the warranty expires,
replacement parts and recommendations for on-site servicing are available from RADIA.
Please contact Customer Care for assistance.
RESTOCKING FEE
A restocking fee will be charged on all unused parts which are returned.
Replacement PartsReplacement Parts
9. O rde r ing9. O rde r ing
RADIA
800-221-1083
763-533-2969
763-852-1811 (FAX)
[e-mail]
For instructional "How To" videos please visit:
www.radiaproducts.com
??

20
Owner’s Manual: 1015
1784593 Rev AD
ECO 18-0069
July 2020
www.radiaproducts.com (PHONE) 800-221-1083 | (INTL) [phone] | (FAX) 763-533-0015
Radia warrants equipment manufactured by it and bearing its name to be free from defects in
material and workmanship.
EXCEPT FOR THE WARRANTY SET FORTH HEREIN, RADIA MAKES NO WARRANTY WHATSOEVER
WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY (a) WARRANTY OF MERCHANTABILITY; (b)
WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE; OR (c) WARRANTY AGAINST INFRINGEMENT
OF INTELLECTUAL PROPERTY RIGHTS OF A THIRD PARTY; WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE.
This warranty applies only when the equipment is installed, operated and maintained in accordance
with written Radia instructions as appearing in the owners’ manuals.
This warranty does not cover, and Radia shall not be liable for, any malfunction, damage, or
wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper
maintenance, negligence, accident, tampering or substitution of non-Radia component parts,
modification or use for non-intended purposes. Nor shall Radia be liable for malfunction, damage or
wear caused by the incompatibility of Radia equipment with structures, accessories, equipment, or
materials not supplied by Radia.
Subject to the limitations set forth above, Radia shall (i) repair or replace the equipment (or the
defective part) or (ii) credit or refund the price of such equipment. Costs of labor and transportation
for service of machines under this warranty will also be covered during the warranty period if Radia
elects to repair or replace the equipment. Normal ground freight will be covered for replacement
parts sent within the warranty period. For customers outside of the US and Canada, the warranty is
for parts only. Ground or common carrier ground freight will be covered for the return of defective
items only. In no case shall Radia's liability exceed the amount of the purchase price.
*All warranty repairs must be executed by a Radia Authorized Service Center or warranty will be
voided.
THE REMEDIES SET FORTH HEREIN ARE PURCHASER’S SOLE AND EXCLUSIVE REMEDY and RADIA’S
ENTIRE LIABILITY FOR ANY BREACH OF THE LIMITED WARRANTY SET FORTH HEREIN.
Please contact your Radia Relationship Manager at 800-221-1083 for specific questions regarding
specific questions regarding warranty terms.
Equipment Covered Under This WarrantyEquipment Covered Under This Warranty
10. Warranty10. Warranty
WarrantyWarranty
Models 1015 PB & SP