Radiall SMP LOCK Series Instruction Manual

TECHNICAL DATA SHEET
1 / 3
STRAIGHT PLUG SOLDER TYPE
R222.L80.010
CABLE .085 Series : SMP LOCK
Issue : 1229 A
In the effort to improve our products, we reserve the right to make changes judged to
be necessary.
All dimensions are in mm.
.
.
pn
ao
COMPONENTS
BODY
CENTER CONTACT
OUTER CONTACT
INSULATOR
GASKET
OTHERS PARTS
-
-
MATERIALS
BERYLLIUM COPPER
BERYLLIUM COPPER
-
PTFE+PEEK
CuAg LOADED SILICONE RUBBER
BERYLLIUM COPPER
-
-
PLATING (µm)
N2PGR
GOLD 1.27 OVER NICKEL 1.27
-
NICKEL 2
-
-

TECHNICAL DATA SHEET
2 / 3
STRAIGHT PLUG SOLDER TYPE
R222.L80.010
CABLE .085 Series : SMP LOCK
Issue : 1229 A
In the effort to improve our products, we reserve the right to make changes judged to
be necessary.
PACKAGING
Standard
Unit
Other
100
-
Contact us
ELECTRICAL CHARACTERISTICS
Impedance
50
Ω
Frequency
0
-
26.5
GHz
VSWR
1.3
+
0,0000
x F(GHz) Maxi
Insertion loss
0.1
√
F(GHz) dB Maxi
RF leakage
-
(
*90
- F(GHz)) dB Maxi
Voltage ra
ting
335
Veff Maxi
Dielectric withstanding voltage
500
Veff mini
Insulation resistance
5000
M
Ω
mini
MECHANICAL CHARACTERISTICS
Center contact retention
Axial force
–
Mating end
6.7
N mini
Axial force
–
Opposite e
nd
6.7
N mini
Torque
NA
N.cm mini
Recommended torque
Mating
NA
N.cm
Panel nut
NA
N.cm
Clamp nut
NA
N.cm
A/F clamp nut
0,0000
mm
Mating life
500
Cycl
es mini
Weight
1,5500
g
ENVIRONMENTAL
Operating temperature
-
55/+125
° C
Hermetic seal
NA
Atm.cm3/s
Panel leakage
NA
SPECIFICATION
CABLE ASSEMBLY
Stripping
a b c d e f
mm
1,78 0,00 0,00 0,00 0,00 0,00
Assembly instruction :
Recommended cable(s)
RG 405
-
Characteristics indicated on this data sheet are those that can be
achieved with the highest performance cable. Intrinsic limitations of
the cable may diminish the performance of the assembly
Cable retention
- pull off ** N mini
- torque NA N.cm
TOOLING
Part Number Description Hexagon
. . .
R282.051.000 STRIPPING TOOL
R282.062.010 POINTER GAUGE
R282.740.030 SOLDERING
MOUNTING
R282.744.253 POSITIONER FOR
SOLDERING SMP
R282.743.120 POSITIONER FOR
SOLDERING SMP
OTHER CHARACTERISTICS
*-90 up to 18 GHz
** See the TDS of the cable assembly
Locking retention > 450 N
500 matings/dematings of the locking sleeve

TECHNICAL DATA SHEET
3 / 3
STRAIGHT PLUG SOLDER TYPE
R222.L80.010
CABLE .085 Series : SMP LOCK
Issue : 1229 A
In the effort to improve our products, we reserve the right to make changes judged to
be necessary.
COMPONENTS
1
4
2
5
Sub-assembly Insulator/center
contact
Body
Insert the cable into the clamp element.
Present the pointer in front of the clamp element.
Push the cable until it stops, while holding the clamp
element pushed on the hollow part of the pointer.
Turn the clamp element until the release of the pointer.
Present the cutting element in front of the clamp
element.
Push and turn both elements, back part opposite to
the front part.
Once they reach the stop, pull without revolving.
After cooling, remove the assembly from the jig.
After cooling, remove the assembly from the jig.
Put the connector in position unlocked on the
positioner
Slide the cable into the connector until it
bottoms against the soldering fixture.
Tighten.
Put three rings of solder around
the cable and solder.
1
2
4
1
2
Clamp element
3
2
4 (solder)
Pointer
Cutting element
3
3
a
We recommend a cable thermal preconditioning before assembly
3
Mount the positioner A.
Slide the center contact into the positioner A.
Insert the solder gauge between the sub-assembly
insulator/center contact and the cable.The gap must be of
0.1 mm
Tighten.Solder the center contact.
2
4
5
3
1 - Positioner A
3
If necessary trim the inner of the cable with the
pointer Gauge.
1

Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Radiall:
R222L80010