Radiant TS8100-TIM-H User manual

TS8100-TIM-H Programmable Timer
ver 1.1
LCD Symbols
Conguration Menu
Setting the clock and day of the week
Select the required operating mode
This timer is tted with a real time clock. It is essential that the clock time and day are set accurately if you require your programmed events to start on time. Follow below steps,
1) Touch time display .
Auto - Automatic mode, the timer executes the preprogrammed schedules. To adjust these schedules, see page 2 the program section.
In addition to Automatic mode, this thermostat has a manual modes. The manual mode maintains a constant on or o status set by the user.
To change the ON/OFF status, touch ON /OFF display area. Use or to adjust. Touch to store and exit.
See overleaf for further setting up information
2) Touch day display .
Use or to change the time. Press and hold
Use or to change the day. Touch to store and exit. (or touch Day display to cancel and exit).
or to change the time faster. Touch to store and exit( or touch time display to cancel and exit).
The buttons are locked
Turning on/o the timer
Automatic mode, executes the programmed schedules
Manual mode Temporary override your program
AUTO
O / RIDE
Symbols
The program number
Day of the week. Day 1= Monday, Day 2= Tuesday... etc.
Day
Program 1,2,3,4
Symbols Description
Description
Menu #
01
02
Features description Features Explanation Touch or to adjust
Backlight turning-on time 10, 20,30,40,50,60 seconds. 30 seconds by default
To set the backlight turning-on time when the screen is pressed.
Clock format 24H / 12H 24 hour clock by default12 Hour or 24 Hour clock format selection
03
Done
Done
Done
Then you will see menu 01. Touch or to select the menu number. Use or adjust the settings. Touch to accept and store.
Previous Done
Next
5+2 /7 Day program mode This allows you to program either 5 days at once, then the 2 days of the weekend 5 2 = 5+2 day programmable
separately, or a full 7 days at the same time or 7 days separately 7 = 7 day programmable (by default)
touch to turn timer o, and now touch
Set Menu
To enter into menu settings,
page 1
LCD SYMBOLS
CONFIGURATION MENU
SETTING THE CLOCK + DAY OF THE WEEK
TS8100-TIM-H TIMER INSTRUCTIONS
See overleaf for further instructions >>>
SELECT THE REQUIRED OPERATING MODE
Radiant Australia Pty Ltd Unit 1 / 18 Profit Pass, Wangara, WA 6065
Telephone: [phone] Fax: [phone] Email: [email protected]

Save money by setting program schedules
This timer can be individual 7-day programmable. For each day of the week you are able to have 4 timed set schedules.
Above are default program schedules, to make changes, follow easy steps as below.
07:001
2
3
4
ON
16:30 ON
09:30 OFF
22:30 OFF
Program Start Time Set To
Installation and Wiring
Press , you will see day display ashing.
Use or adjust the day to the day you wish to start programming
Press , the LCD will show program 1 with the time display ashing.
Use or adjust the time you wish the program 1 event to commence
Press , the LCD will show ON or OFF value ashing.
Use or select ON or OFF to be maintained for
Press , now the LCD will show program 2 with the time display
Repeat step 4,5,6 to set remaining programs. Press to store and exit.
During setting programs, press (if visible) will clear a program entry
1.
2.
3.
4.
5.
5.
6.
6.
7.
8.
TS8100-TIM-H Programmable Timer
ver 1.1
(Press to select all days of the week, to cancel selecting all days of
DONE
DONE
All Days
All Days
Set
Schedule
Temporary Override
Touch the ON or OFF display, and it will start to ash. Use
or
to adjust. Press to accept, and you will see “O/RIDE” on LCD. The timer will maintain the
new set status until the next programmed event. To cancel the override setting, press
Lock the Keypad
To lock the keypad, press and hold the bottom left corner of display for 5 seconds, you will see a lock symbol .
Reset to Factory Settings
With the timer turned o, press and hold the up left corner of display for 5 seconds until you can see“ ”（RESET）on LCD.
To unlock, repeat the steps above.
DONE
Run
Schedule
Next
Next
Next
Next
Next
Next
Delete
until the beginning of the next program.
Note: It is faster to program the same schedule for the entire week and then to adjust the exceptional days.
Set time and temperature for the next time period. Repeat steps 2 and 3
for each time period of the weekday.
In 7 day program mode In 5+2 day program mode
NOTE:
ashing, signifying the second daily event is now being programmed.
the program 1 event.
for the currently selected day or days.
the week, press again.)
or to the day you wish to edit an existing event or program.
Press , you will see the time ashing.
Press to move to the weekend(sat-sun) time periods settings.
Use or to set your weekday Wake time(Mon-Fri), then press
1.
2.
3.
4.
Use or to set the temperature for this time period, then press
Set
Schedule
Press to save and exit.
Day 1 - 5, refers to the weekday( Monday to Friday)
Day 6 - 7, refers to the weekend( Saturday and Sunday)
and the timer will maintain the ON or OFF status of the last executed program
page 2
Installation and Wiring
Carefully separate the front half of the timer switch from the back plate by placing a small
flat head terminal driver into the slots on the bottom face of the the timer switch.
Carefully unplug the ribbon connector which is plugged into the front half of the timer switch.
Place the time switch front half somewhere safe. Terminate the timer switch as shown in the
diagrams below.
Screw the timer switch back plate on to the flush box
Re-connect the timer switch ribbon cable and clip the two halves together.
This product should be installed
by a qualified electrician.
not in use
SETTING THE PROGRAM SCHEDULES
INSTALLATION AND WIRING
Radiant Australia Pty Ltd Unit 1 / 18 Profit Pass, Wangara, WA 6065
Telephone: [phone] Fax: [phone] Email: [email protected]