Radionics D269 User manual

D269 Independent Zone Control
User Guide
General Information
Your Model 269 Independent Zone Control is an arming station
thatprovidesyouwithcontroloveraspecifiedareaofyoursecurity
system. The 269 gives you independent control of this area,
regardless of whether the rest of your security system is armed
or disarmed.
Features of the Model 269 include protection status display
indicators, entry and exit delay time, prewarning sounder and
user programmable passcode.
The Zone Control Display
The Zone Control has two protection status display indicators: a
STATUS indicator and an ARMED indicator.
STATUS
When the green indicator is lit, the specified area is ready to be
armed. When the green indicator is not lit, there is a faulted
sensor in the specified area. Correcting the fault usually means
closing a door or a window.
ARMEDWhen the red indicator is lit, the area is armed. When the red
indicator is not lighted, the area is not armed.
TheKeypad
The Zone Control has a digital keypad used to enter your
personal passcode into the security system. It is your personal
passcode which arms and disarms the specified area.
When entering your passcode, if the Zone Control emits a short
warning tone each time you touch a key, check the STATUS
light, as this indicates a problem with a device in the protected
area.
Arming the Specified Area
1) Ensure that the specified area is secure. The green
STATUS indicator light must be on.
2) Enter your personal passcode. The red ARMEDindicator
light flashes on and off to indicate exit delay time
(approximately 60 seconds). When the ARMED indicator
lights steadily, the specified delay area is armed.
R

D269 User Guide
71-04759-000-D Page 2 © 2000 Radionics
Disarming the Specified Area
Your specified area is disarmed by entering your personal
passcode. When the area is armed, you must enter the premises
through a designated entry door to prevent an instant alarm
condition. Opening the delay door starts a 30 second delay
during which the Zone Control sounds a warning to remind you
to disarm the system. To disarm the system, enter your personal
passcode before the entry time expires. If you enter through a
wrong door or fail to disarm the system before the entry delay
expires, you will generate an alarm.
Silencing the Alarm
Your alarm audible device sounds for a specific period of time
before it shuts off automatically. If an alarm occurs and you want
to silence the alarm, simply enter your personal passcode and
the audible device shuts off.
IMPORTANT
Some security systems do not permit the D269
IndependentZoneControltosilencethealarm. The alarm
must be silenced from a different control station in your
system.
My system can be silenced from the D269 Independent
Zone Control Station.
My system must be silenced from the control station
located:
User Programmable Passcode (Optional)
Your Model D269 Independent Zone Control provides you with
the convenient feature of changing your personal passcode
whenever you feel it necessary. It is recommended that you
write down your old passcode and the new one before you
begin.
My system has this feature
My system does not have this feature.
D269
User Guide

D269 User Guide
© 2000 Radionics Page 3 71-04759-000-D
D269
User Guide
Notes About ProgrammingYour Personal Passcode:
•Programming must be completed in 60 seconds.
•You may only program while the Independent Zone Control is
disarmed.
•Do not program the same digit twice in a row.
(Example: 2445 is an improper passcode)
•Do not program the first and the last digit the same.
(Example: 4564)
•The new combination must be four digits in length.
Programming Steps:
1) Press the center key in the bottom row of keys on the
keypad.
2) Enter the old passcode once.
3) Enter the new four digit passcode twice.
4) Test the new passcode by arming and disarming.
5) If you encounter difficulties repeat steps 1 through 4.
STATUS ARMED
123
456
789
R

©2000Radionics,adivisionofDetectionSystems,Inc. 71-04759-000-D 8/00
®TheRadionicslogoisaregisteredtrademarkofRadionics UserGuide D269
Page4of4