Radionics D2112 User manual

1
Radionics, Inc.
74-07113-000-B 4/94
D2112 Keypad
Diagnostics
Putting the Keypad into the
Diagnostics Mode
1. Lock the D2112's
Standby Switch down.
2. Press the 1 key on the
keypad.
3. Enter your “Installer”
passcode. The default
Installer passcode is
654321. The default
passcode length is 3, so
if you have not changed
the default entries, press
654.
Lights on the keypad
indicate the functions
that are available.
Now that you’re in...
When you select a function
the light next to the key winks
to let you know what function
you are in. Once inside a
function, press ( CLEAR ) to
return to the previous level.
1Bell Test
2Battery
3Comm-
4
5Point
6Relays
7Power
8Program
Status
unication
Supply
74-07113-000-B 4/94 © 1994 Radionics

2
Radionics, Inc.
74-07113-000-B 4/94
Bell Test
The Bell Test powers the external bell with the
burglar pattern for 2 seconds.
• Press ( 1 )
The Bell Test times out after 2 seconds.
Battery Test
The Battery Test causes the panel to run on
battery only for 4 minutes. During this time if the
voltage drops below 12.2, the trouble tone
sounds and the low battery condition appears in
the “Check Trouble Mode”.
When the Battery Test is initiated by the user
initiating "Test System", a Low Battery report or
a Missing Battery report will be sent if
programmed.
• Press ( 2 ).
The Battery Test times out in 4 minutes.
Communication Test
The Communication Test sends a Test report to
the receiver. If the report fails to be
acknowledged after all dialing attempts, the
D2112 goes into Communications Failure.
• Press ( 3 ).
The Communication Test times out immediately.
1
2
3

3
Radionics, Inc.
74-07113-000-B 4/94
Point Status
The Point Status function displays the electrical
state of all points. The state of each point is
shown with its corresponding light.
1. Press ( 5 ).
The lights update every second.
Light Point State
OFF Normal
WINK Open
ON Short
2. Press ( CLEAR ) to exit this test.
Relays
The Relays function can activate either of the
two external relay outputs.
1. Press ( 6 ) to enter the Relays function.
2. Press and hold ( 1 ) to activate relay 1.
...light 1 will be on while you hold the key.
3. Press and hold ( 2 ) to activate relay 2.
...light 2 will be on while you hold the key.
4. Press ( CLEAR ) to exit this test.
Power Supply Status
The Power Supply Status function performs four
different tests on the power supply and battery.
The results of the test are displayed as a bar
graph using lights 1 through 8.
For example: If the current consumption is at
500mA, lights 4, 5, 6, 7 and 8 are on.
When a test indicates an overload condition,
the bar graph flashes.
5
7
6

4
Radionics, Inc.
74-07113-000-B 4/94
Power Supply Status (Cont'd)
To enter the Power Supply Status mode,
1. Press ( 7 ).
Light 7 winks to let you know that you’re in
the Power Supply Status function.
…To display Fire Alarm Load
2. Disconnect the battery.
3. Press ( 1 ).
The bell and external relays activate, and
the current consumption displays.
4. Hold the Current Consumption scale next to
your keypad. Verify that the current
consumption is less than 860mA.
5. Press ( CLEAR ).
6. Reconnect the battery.
…To display Normal Supervisory Load
2. Disconnect the battery.
3. Press ( 5 ).
The current consumption displays.
4. Hold the Current Consumption scale next to
your keypad and verify that the current
consumption is less than 350mA.
5. Press ( CLEAR ).
6. Reconnect the battery.
7
Radionics, 1 Park Gate Close, Bredbury,
Stockport, Cheshire, SK6 2SZ, England
Technical Support: [phone]

5
Radionics, Inc.
74-07113-000-B 4/94
Current Consumption
Scale
mA Light
Maximum Fire 860 1
732 2
605 3
477 4
Maximum Normal 350 5
222 6
95 7
8
Alarm Load ☛
Supervisory Load
When a test indicates
an overload condition,
the bar graph flashes.
☛

6
Radionics, Inc.
74-07113-000-B 4/94
Power Supply Status (Cont'd from page 4)
…To display the Minimum Battery
Voltage After 1 Minute
2. Make sure the battery is connected.
3. Press ( 2 ).
The D2112 automatically disconnects AC.
The keypad displays the lowest battery
voltage during the test, and gives an
acknowledge tone after 1 minute.
4. Hold the Battery Voltage scale up next to
your keypad. Verify that the battery does not
drop below 13.25 volts within the minute.
5. Press ( CLEAR ).
…To Read Battery Voltage
2. Make sure the battery is connected.
3. Press ( 4 ).
The battery voltage displays.
4. Hold the Battery Voltage scale up next to
your keypad to see the voltage level. A low
battery condition displays by flashing lights
5, 6, 7, and 8.
5. Press ( CLEAR ).

7
Radionics, Inc.
74-07113-000-B 4/94
Battery Voltage
Scale
Volts Light
13.75 1
Minimum Battery 13.25 2
12.75 3
Read Battery 12.25 4
11.75 5
11.25 6
10.75 7
10.25 8
Voltage
Low battery flashes
lights 5, 6, 7, 8.
☛
Voltage after
1 Minute ☛

8
Radionics, Inc.
74-07113-000-B 4/94
Programming
Function 8 is the Keypad Programming Mode.
For complete instructions on programming from
the keypad, see the D2112 Control/
Communicator Program Entry Guide (74-07112-
000).
System Troubles
This diagnostic check is available in the user's
Check System (Key 4) mode.
1. Exit the Diagnostics Mode.
2. Press ( 4 ).
If light 5 is lit a system trouble exists. To find
out what the trouble is,
3. Press and hold key ( 5 ). The lights indicate
the specific type of trouble:
Low or Missing Battery 1
Standby Switch Locked 2
Aux Power Trouble 3
Bell Power Trouble 4
8
74-07113-000-B 4/94
© 1994 Radionics, Inc., Salinas, CA. All rights reserved.
The Radionics logo is a registered trademark of Radionics, Inc.
Radionics, Inc., 1800 Abbott Street
Salinas, CA, 93901, U.S.A.
Customer Service: [phone]