RADVision SCOPIA XT4200 User manual

© 2012 RADVISION Ltd. All intellectual property rights in this publication are owned by RADVISION Ltd. and are protected by United States copyright laws, other applicable copyright laws and international treaty provisions. RADVISION Ltd. retains all rights not expressly granted.
This publication is RADVISION confidential. No part of this publication may be reproduced in any form whatsoever or used to make any derivative work without prior written approval by RADVISION Ltd. No representation of warranties for fitness for any purpose other than what
is specifically mentioned in this guide is made either by RADVISION Ltd. or its agents. RADVISION Ltd. reserves the right to revise this publication and make changes without obligation to notify any person of such revisions or changes. RADVISION Ltd. may make improvements or
changes in the product(s) and/or the program(s) described in this documentation at any time. If there is any software on removable media described in this publication, it is furnished under a license agreement included with the product as a separate document. If you are unable to
locate a copy, please contact RADVISION Ltd. and a copy will be provided to you. Unless otherwise indicated, RADVISION registered trademarks are registered in the United States and other territories. All registered trademarks recognized. All right reserved.
For further information contact RADVISION or your local distributor or reseller. http://www.radvision.com
System Installation and Activation
Connect all cables to the SCOPIA XT4000 series Codec Unit (see overleaf). Power supply must be connected after all other connections have been established.1.
Turn on the TV monitors. Monitor on HDMI1 is mandatory, monitor HDMI2 is optional.2.
Make sure the remote control has batteries installed.3.
Verify that the LED on the front panel of the Codec Unit is turned on.4.
If the codec unit does not turn on automatically, press the5. button on the remote control.
The graphical menu appears on the monitors.6.
A
Moving the Camera
On the general screen,1.
navigate to Control Camera
using the arrow keys and
press OK.
Use the arrow keys to move2.
the camera to the preferred
position.
Press Back when done.3.
G
CAUTION: Make sure all units are
switched off whenever connecting
or disconnecting devices.
Network Settings
Enter your network settings.1.
For questions about this
information, consult your system
administrator.
Then select Next.2.
Gatekeeper Settings
Enter your Gatekeeper settings1.
and your E.164 number.
For questions about this
information, consult your system
administrator.
Then select Done.2.
E F
Country and Language of
Interface
System Name field displays the1.
name of this Codec Unit as
displayed in a video conference,
for example:
Hong Kong,• or
9th Floor Conf Rm•
Use the remote control keypad2.
to type the name. Press OK to
toggle letters or numbers and
lower/upper case.
Select the Country and preferred3.
Language.
Then select Next.4.
C
Product Registration
Open the envelope that came with the XT4200.1.
Locate the serial number and product key.2.
On a computer, open a browser and navigate to3.
http://licensing.radvision.com.
Complete the online registration form and enter the serial number and product4.
key. The web registration form returns a license key.
Write down the license key and keep it in a safe place for future use.5.
B
Graphics and Image Setup
If all the sides of the triangles 1 and
2 are visible on your monitor, select
next.
Otherwise, press 1 to adjust the1.
position of the top left corner.
Use the arrow keys to move2.
the selected triangle until it is
fully visible on your monitor.
Press OK when done.
Press 2 to adjust the position of3.
the bottom right corner.
Repeat the procedure using the4.
arrows.
Press OK and Next when done.5.
D
SCOPIA XT4200 Quick Setup Guide
Package Content:
SCOPIA XT4000 series Codec Unit•
SCOPIA XT XT4200 Camera•
SCOPIA XT 1-way Microphone POD•
SCOPIA XT Remote Control Unit•
Base Camera kit: 2.5m triple camera cable,•
including power, VISCA and DVI-D/HDMI
DVI-I to VGA converter•
Cable LAN 4mt•
Cable HDMI M/M, 2.5M•
Power Supply and power cable•
1-way Microphone POD cable•
Remote Control Batteries•
PN 62111-00011 rev A01
XT4 200XT4 200

SCOPIA XT4200
Quick Hardware Setup
CAUTION: Make sure all units are
switched off whenever connecting
or disconnecting devices.
Package Content:
Codec Unit
SCOPIA XT4200 Camera
1-way Microphone POD
Remote Control Unit and Batteries
Codec Unit Camera Cable
HDMI Cable
1-way Microphone POD cable
Ethernet Cable for LAN, 4m
Power Supply and Power Cable
DVI-I to VGA converter for PCs with VGA output only
XT4 200
XT4200 Camera
Make sure to
connect the cable
into the IN connector.
4
15
14
8
5
2
Digital or
Analog
Media
Device
Remote Control
Batteries
Battery model:
CR2025
LITHIUMBATTERY
3V
LITHIUMBATTERY
3V
DC IN 12V IN RS-232C OUT DVI
IR SELECT
1 2 3
1
2
3
4
5
6
7
8
9
SYSTEM
SELECT
Layouts PiP Inputs Help
SelectMemo
Far Near Presets
9
1
6
7
12
SCOPIA XT4000 series
Codec Unit
Please set the system
selector on the back
of the camera to 7.
16
10 13
11
CAUTION: the mains
cable is used as a
disconnecting device,
use therefore an easily
accessible outlet
located near the
device for the power
supply connection.
Never remove the
mains plug while the
device is connected.
3
RADVISION Optional –
Not Included Accessories
Audio Cable. Both sockets on the unit are dual purpose.
They accept either an analog 3.5mm MiniJack cable
or an optical Toslink cable with a Toslink mini-plug
adapter. Optical digital audio format is S/PDIF. 1-way
microphone POD is connected to the analog/optical
input. Analog/optical output can be used for connection
to analog or digital media device.
Optional microphone POD
DVI to DVI Cable
Non-RADVISION
HDMI Cable for second monitor
Ethernet Cable for LAN2. Second LAN is optional,
and a license key is needed to unlock it.
VGA cable