Rail King AeroTrain Diesel Locomotive User manual

AeroTrain
Diesel
Locomotive
OPERATOR’S MANUAL
PLEASE READ BEFORE USE AND SAVE
Compatibility
This engine will operate on any
traditional O-31 Gauge track
system, including M.T.H.’s
RealTrax®or ScaleTrax™or
traditional tubular track. It is also
compatible with most standard AC
transformers. (See page 15 for a
complete list of compatible
transformers and wiring
instructions.)

CAUTION: ELECTRICALLY OPERATED PRODUCT:
Not recommended for children under 10 years of age. M.T.H. recommends adult supervision with children ages 10 - 16.
As with all electric products, precautions should be observed during handling and use to reduce the risk of electric shock.
WARNING: When using electrical products, basic safety precautions should be observed, including the followi ng:
Read this manual thoroughly before using this device.
M.T.H. recommends that all users and persons supervising use examine the hobby transformer and other electronic equipment
periodically for conditions that may result in the risk of fire, electric shock, or injury to persons, such as damage to the primary
cord, plug blades, housing, output jacks or other parts. In the event such conditions exist, the train set should not be used until
properlyrepaired.
Do not operate your layout unattended. Obstructed accessories or stalled trains may overheat, resulting in damage to your layout.
This train set is intended for indoor use. Do not use if water is present. Serious injury or fatality may result.
l
l
l
lDo not operate the hobby transformer with damaged cord, plug, switches, buttons or case.
Table of Contents
Set Up Checklis t...................................................................................................3
Lubrication.............................................................................................3
Basic Operation ....................................................................................................4
Activating Features.................................................................................4
Configuring For Display......................................................................................5
Loco-Sound Operating Instructions...................................................................6
Activating Loco-Sound Features........................................................... 6
Speed Control........................................................................................ 7
Locking Locomotive Into A Direction.................................................. 8
Using Proto-Cast and Proto-Dispatch Features..................................... 8
Maintenance.........................................................................................................9
Lubricating and Greasing Instructions...................................................9
Cleaning The Wheels, Tires and Track..................................................10
Traction Tire Replacement Instructions.................................................11
Headlight Replacement Instructions......................................................12
Troubleshooting Loco-Sound Problems................................................ 13
Transformer Compatibility and Wiring Chart....................................... 15
Service & Warranty Information........................................................... 16
Limited One-Year Warranty..................................................................16

RailKing AeroTrain Locomotive 3
Set Up Checklist
•Lubricate the locomotive
•Apply power to run as described in the Basic Operating Section of this manual
Lubrication
You should lubricate the engine to prevent it from squeaking. Use
light household oil and follow the lubrication points marked “L” in
Fig. 1. Do not over-oil. Use only a drop or two on each pivot point.
Lubricate Pick Up Rollers (L)
Lubricate Pick Up Rollers (L)
Lubricate Wheel Axles (L)
Figure 1. Lubrication Points on the Locomotive
DO NOT
OVER OIL

4RailKing AeroTrain Locomotive
Basic Operation
The Throttle knob controls how fast your train will travel.
Turn the throttle knob up ½-way, until the engine and caboose lights shine bright.
Put the engine into motion by pressing the Direction button on your transformer once.
(hold it for approximately 1 second)
If the engine does not begin to move as soon as you firmly press the Direction button,
you may not have sent enough voltage to the track to make the train move. Turn the
throttle up a bit higher until the train begins to move.
Throttle To increase or decrease track voltage, and therefore train speed, turn the
throttle control knob. Turning clockwise will increase voltage and speed, while turning
counterclockwise will decrease voltage and speed. The engine will maintain the speed
you set after you release the throttle until you turn it again to change the voltage and
speed.
Bell - To sound the bell, in an engine equipped with a bell firmly press and release the
Bell button. To turn the bell off, press and release the Bell button again. The bell will
continue to ring from the time you turn it on until you press and release the button again
to turn it off.
Horn/Whistle - To sound the whistle, firmly press the Horn/Whistle button. The whistle
will sound for as long as you continue to depress the button. It will stop when you
release the button.
Direction Your train is programmed to
start in neutral. The train will always
cycle neutral-forward-neutral-reverse with
each press and release of the direction
button. The engine is programmed to
restart in neutral each time the track
voltage is turned off for 25 seconds or
more.
Cycle Phases
Neutral
Neutral
ForwardReverse
Activating Features

RailKing AeroTrain Locomotive 5
Manual Volume Control
To adjust the volume of all sounds made by this engine, turn the master volume control
knob located next to the fuel tank clockwise to increase the volume and
counter-clockwise to decrease the volume.
Proto-Sound 2.0
VolumeAdjustmentKnob
Figure 2: Manual Loco-Sound Volume Adjustment
Configuring For Display
It is possible to configure the powered unit for prototypical appearance when desiring to
only display the model. Such a configuration can be accomplished by following the
directions below to change the powered unit’s trailing power truck guide wheel
placement.
Unscrew and remove
guide wheels from
trailing power truck on
powered unit
Center trailing power truck
on frame and screw
guide wheels into holes
provided on frame
as shown.
Unscrew and remove
pickup roller assembly
from trailing power
truck to reveal
pickup roller assembly
insulating pad
Rotate pickup roller
assembly insulating
pad 180 degrees and
reattach pickup roller
assembly with roller
facing toward truck
block as shown.

6RailKing AeroTrain Locomotive
Loco-Sound features are activated by sequences of Bell and Horn button pushes
described below. Please read the full descriptions of each feature before using it. To use
these buttons to activate features rather than to blow the horn or ring the bell, you should
tap the buttons very quickly with a ½-second pause between button presses. You may
need to practice your timing to make this work smoothly.
Loco-Sound
Operating Instructions
Timing Chart
Total Time Lapse: 1 Seconds½
Press
Horn
Short &
Firm
½ Sec.
Pause
½ Sec.
Pause
Press
Bell
Short &
Firm
Press
Bell
Short &
Firm
Feature to Be Activated:
Speed Control On/Off
Lock into a Direction/Unlock
Button Code:
1 Whistle, 2 Bells
1 Whistle, 3 Bells
Activating Proto-Sound 2.0 Conventional
Mode Features

RailKing AeroTrain Locomotive 7
M.T.H. engines equipped with Loco-Sound have speed control capabilities that allow the
engine to maintain a constant speed up and down grades and around curves, much like an
automobile cruise control. You can add or drop cars on the run, and the engine will
maintain the speed you set.
While the engine is programmed to start with the speed control feature activated, you can
opt to turn it off. This means the engine's speed will fall as it labors up a hill and increase
as it travels downward. It is also affected by the addition or releasing of cars while on the
run. Because the engine will run more slowly at a given throttle voltage when speed
control is on than when it is off, you should adjust the throttle to a lower power level for
operation with speed control off to avoid high-speed derailments. When speed control is
off, the volume will drop to allow for better low voltage operation.
To turn speed control on and off, put the engine in neutral, then quickly tap the
transformer's Horn button one time then quickly tap the Bell button two times, allowing
approximately ½ second to lapse between each quick button press. Two horn blasts will
indicate that the engine has made the change. Repeat the 1 horn, 2 bells code to return it
to the other condition. You will want to do this during the initial neutral upon start-up if
you ever couple this engine to another engine that is not equipped with speed control to
avoid damaging the motors in either engine. Each time you shut down the engine
completely, it will automatically turn speed control on.
Horn
Place
Engine into
Neutral
Bell Bell
=
Speed Control
Two Horn Blasts
Repeat to Return
to Normal Condition
Speed Control
Locking Locomotive Into A Direction
You can lock your engine into a direction (forward, neutral, or reverse) so that it will not
change directions. To do this, put the engine into the direction you want (or into neutral
to lock it into neutral), run it at a very slow crawl (as slowly as it will move without
halting), and quickly but firmly tap the Horn button once followed by three quick taps of
the Bell button, allowing approximately ½ second to lapse between each quick button
press. Two horn blasts will indicate that the engine has made the change. The engine will

8RailKing AeroTrain Locomotive
Horn
Place
Engine into
Desired
Direction
Horn Bell Bell Bell
=Direction Lock
Repeat to Return
to Normal Condition
When used with the RailKing Remote Lock-on (sold separately), Loco-Sound-equipped
engines gain Proto-Cast ™and Proto-Dispatch™features.
Proto-Cast: This feature allows you to play audio recordings through your engine’s
speakers. You must supply the audio source (a small portable is sufficient) and a
male-to-male mini cable (1/8” plug, like that used for the headset with a portable CD/tape
player) to connect your audio source to the remote lock-on. To use Proto-Cast, simply
plug the mini-cable into your audio source (usually into the headphone jack) and into the
“Audio” port on the right side of the remote lock-on and adjust the volume.
Proto-Dispatch: This feature allows you to broadcast your own voice through your
engine’s speakers. You must supply the microphone and a mini cable (1/8” plug, like
that used for the headset with a portable CD/tape player) to connect your microphone to
the remote lock-on. To use Proto-Dispatch, simply plug the mini-cable into the
microphone and into the “Mic” port on the left side of the remote lock-on and speak into
the microphone.
When these features are in use, the locomotive’s own sounds (engine sounds and bells,
whistles, and horns) will be muted so that only the sounds you broadcast will be heard.
Because these two features are voice activated, there will be a 10-15 second delay after
you stop speaking into the microphone or turn off the audio source before the engine
sounds resume. To stop using the feature and return to normal operation, unplug the cable
from the lock-on jack.
If using parallel tracks with multiple Loco-Sound-equipped engines, Proto-Cast and
Proto-Dispatch transmissions from one track may be picked up by the other nearby
engines.
If you experience popping and interference, try cleaning the track with denatured alcohol
as described in the “Cleaning the Wheels, Tires and Track” section of this booklet.
Using Proto-Cast and Proto-Dispatch Features
not change direction (including going into neutral) until you repeat the 1 horn, 3 bells
code to return the engine to its normal condition, even if the engine is kept without power
for extended periods of time.

RailKing AeroTrain Locomotive 9
Maintenance
The engine should be well oiled and greased in order to run properly.
Regularly lubricate all axles and linkage components and pickup rollers
to prevent squeaking. Use light household oil, such as that found in
M.T.H.'s maintenance kit. Do not over oil. Use only a drop or two on
each pivot point.
DO NOT
OVER OIL
Body Mount Screws
Body Mount Screws
(Note: Front Body Screws
Are Shorter Than Middle and Rear Body
Screws. Do use Rear or Middle Screws In
Front Screw Holes To Reattach Body To
Chassis Or Damage To Body Can Result)
NOT
Motor Mounting Screw
(Pickup Roller Must Be Removed First)
Grease Idler Gear (G)
Figure 3
The locomotive’s internal gearing was greased at the factory and should not need
additional grease until after 50 hours of operation or one year, whichever comes first.
Follow the greasing instructions below. Note that in some tightly packed engines you
may need to move internal components temporarily in order to access the gears.
1. To access the gear box, remove the cab from the chassis by unscrewing the chassis
screws as seen in Figure 3 and lifting the cab from the chassis.
2. Once the cab is removed, remove the trucks by unscrewing the black Phillips motor
mount screw located on the underside of the drive trucks (see Fig. 7).
3. Once the motor mount screw has been removed, pull the motor away from the truck
block and lightly coat the motor worm gear and bronze drive gear (in the truck block)
with grease.
4. Reassemble the truck and motor, being careful not to pinch any wires between the
truck block and motor mount.
Lubricating and Greasing Instructions

10 RailKing AeroTrain Locomotive
5. After repeating the procedure for the other motor, reassmble the chassis and body,
being careful that the wire harnesses are not caught between the chassis and body and
reinstall the chassis screws.
Lubricate the outside truck block
idler and drive gears with grease.
Use the diagram shown in Figure
6 below as a guide and add grease
to the points marked with a “G.”
Periodically check the locomotive wheels and pickups for dirt and buildup, which can
cause poor electrical contact and traction as well as prematurely wear out the neoprene
traction tires.
Periodically check the locomotive
wheels and pickups for dirt and
buildup, which can cause poor
electrical contact and traction and
prematurely wear out the neoprene
traction tires. Wheels and tires can be
cleaned using denatured (not rubbing)
alcohol applied with a cotton swab.
To clean the track, use RailKing Track
Cleaning Fluid and a clean rag or
denatured (not rubbing) alcohol.
Unplug the transformer and wipe the
rails of the track, turning the rag
frequently to ensure that you are using
clean cloth on the rails. Thereafter,
keep an eye on the track and clean it
when it gets dirty to ensure good electrical contact and to lengthen the life of the tires.
Motor Mount Screw
Figure 4
Cleaning The Wheels, Tires and Track

RailKing AeroTrain Locomotive 11
Your locomotive is equipped with two neoprene rubber traction tires on each powered
truck block. While these tires are extremely durable, you may need to replace them at
some point.
First, remove the truck sides from the truck block. To do this, turn your engine upside
down. If there are visible Phillips screw heads between the truck frame and truck block
(see Fig. 5), go to step A. If not, go to
step B.
A. Remove the two Phillips screws that
attach the truck sides to the truck block.
B. Remove the trucks from the chassis
and the truck sides from the trucks in
order to slip the new tire over the
grooved drive wheel. See Fig. 5 for
which screws you must remove to do this.
Once the truck sides have been removed:
1. Make sure the old tire has been
completely removed from the groove in
the drive wheel, using a razor blade or small flathead screwdriver to pry away any
remains.
2. Slip the new tire onto the wheel. You may find it useful to use two small flathead
screwdrivers to stretch the tire over the wheel.
3. If you twist the tire while stretching it over the wheel, you will need to remove and
reinstall the tire. Otherwise your engine will wobble while operating.
4. Make sure the tire is fully seated inside the groove. Use a razor blade to trim away any
excess tire that will not seat inside the groove properly.
5. Reassemble in the reverse order.
One set of replacement tires is packaged with your model. Additional sets are available
directly from the M.T.H. Parts Department (phone: [phone]; e-mail:
[email protected]; mail: 7020 Columbia Gateway Drive, Columbia MD
21046-1532).
Screws to Remove Trucksides
Figure 5
Traction Tire Replacement Instructions

12 RailKing AeroTrain Locomotive
The locomotive’s headlight is controlled by a constant voltage circuit in the engine. The
headlight is easy to remove and replace when it burns out. The bulb has a quick
disconnect plug that attaches the bulb harness to a light circuit. Replacement bulbs are
available directly from the M.T.H. Parts Department.
Follow the body removal instructions found in the Lubrication and Greasing Instructions.
Gently disconnect the bulb harness from the socket on the constant voltage circuit and
replace the bulb.
Replaceable Lights
Headlight
Wire Harness
Figure 6
Headlight Replacement Instructions

RailKing AeroTrain Locomotive 13
Although Loco-Sound has been designed and engineered for ease of use, you may have
some questions during initial operation. The following table should answer most
questions. If your problem cannot be resolved with this table, contact M.T.H. for
assistance (telephone: [phone]; fax: [phone]; [email protected],
7020 Columbia Gateway Drive, Columbia MD 21046-1532).
Starting Up
Horn
Bell
Remedy
Remedy
Remedy
Remedy
When I first turn the power on, the
engine will not begin to run. I have to
turn the throttle off and then on again
to get the engine to operate.
I can’t get the horn to blow when I
press the whistle button.
I can’t get the bell to ring when I press
the bell button.
You may be pressing the button too
quickly. Try pressing the whistle button
more slowly, taking approximately one
full second to fully depress the button.
You may be pressing the button too
quickly. Try pressing the bell button
more slowly, taking approximately one
full second to fully depress the button.
This is normal behavior. To prevent
accidental high-speed start-ups, Loco-
Sound is programmed to start up in
neutral anytime track power has been
turned off for several seconds. See
the "Basic Operation" section for more
details.
Lock-out Remedy
I can’t get the engine to run after I
power up the transformer. It sits still
with the engine sounds running.
The engine won’t lock into forward,
neutral, or reverse.
The engine is locked into the neutral
position. Follow the procedure in the
“Lock into a Direction” section.
Engine speed must be below 10 scale
mph (approx. 10 volts or less in
conventional mode).
Troubleshooting Loco-Sound Problems

14 RailKing AeroTrain Locomotive
Volume Remedy
The sounds seem distorted, especially
when the whistle or bell is activated.
Loco-Sound volume is set too high.
Turn the volume control knob on the
bottom of the chassis counter-
clockwise to reduce the volume.

RailKing AeroTrain Locomotive 15
Loco-Sound is designed to work with most standard AC transformers. The chart below
lists the many compatible transformers. Note that many of the operational commands
described in these instructions require a bell button, so if your transformer does not have
its own bell button, you should consider adding one to get the full benefit of the system.
In addition, the chart details how the terminals on these transformers should be attached
to your layout.
Transformer
Model Center Rail Outside Rail Min/Max. Voltage
Power
Rating
Transformer
Type
Lionel 1032 U A 5-16v 90-Watt Standard
Lionel 1032M U A 5-16v 90-Watt Standard
Lionel 1033 U A 5-16v 90-Watt Standard
Lionel 1043 U A 5-16v 90-Watt Standard
Lionel 1043M U A 5-16v 90-Watt Standard
Lionel 1044 U A 5-16v 90-Watt Standard
Lionel 1053 U A 8-17v 60-Watt Standard
Lionel 1063 U A 8-17v 60-Watt Standard
All-Trol Left Terminal Right Terminal 0-24v 300-Watt Electronic
Dallee Hostler Left Terminal Right Terminal Electronic
Lionel LW A U 8-18v 75-Watt Standard
Lionel KW A or B U6-20v 190-Watt Standard
Lionel MW Outside Track
Terminal
Inside Track
Terminal 5-16v 50V.A. Electronic
Lionel RS-1 Red Terminal Black Terminal 0-18v 50V.A. Electronic
Electronic
Lionel RW U A 9-19v 110-Watt Standard
Lionel SW U A Unknown 130-Watt Standard
Lionel TW U A 8-18v 175-Watt Standard
Lionel ZW
Lionel Post-War
Celebration
Series ZW
A,B,C or D
A,B,C or D
U
Common
8-20v
0-20v
275-Watt
135/190 Watt
Standard
MTH Z-500 Red Terminal Black Terminal 0-18v 50-Watt Electronic
MTH Z-750 Red Terminal Black Terminal 0-21v 75-Watt Electronic
MTH Z-4000 Red Terminal Black Terminal 0-22v 390-Watt Electronic
* Conventional Mode Only
Transformer Compatibility and Wiring Chart

Service & Warranty Information
Limited One-Year Warranty
How to Get Service Under the Terms of the Limited One-Year Warranty
For warranty repair, follow the instructions below to obtain warranty service.
First, e-mail, write, call or fax an Authorized M.T.H. Service Center in your area or M.T.H. Electric Trains to obtain Repair
Authorization. You can find the list of Authorized Service Centers on the M.T.H. website, www.mth-railking.com. Authorized
Service Centers are required only to make warranty repairs on items sold from that store; all other repairs may or may not be done
at the store's own discretion. Otherwise, contact M.T.H. (fill out the Service Contact form in the Service Section of www.mth-
railking.com; send US mail to the address listed below; tel: [phone]; fax: [phone]), stating when the item was
purchased and describing the problem. If you contact M.T.H., you will be given a return authorization number to assure that your
merchandise will be properly handled upon its receipt.
CAUTION: Make sure the product is packed in its original factory packaging including its foam and plastic wrapping material so
as to prevent damage to the merchandise. The shipment must be prepaid and we recommend that it be insured.
lease make sure you have followed the instructions carefully before returning any merchandise for service.
See our website at or call 1-888-640-3700 to identify an Authorized M.T.H. Train Merchant near you .
M.T.H. products are warrantied for one year from the date of purchase against defects in material or workmanship, excluding wear
items such as light bulbs, pick-up rollers, batteries, smoke unit wicks, and traction tires. We will repair or replace (at our option)
the defective part without charge for the parts or labor, if the item is returned to an Authorized M.T.H. Service Center or M.T.H.
Electric Trains within one year of the original date of purchase. This warranty does not cover damages caused by improper care,
handling, or use. Transportation costs incurred by the customer are not covered under this warranty.
Items sent for repair must be accompanied by a return authorization number, a description of the problem, and
, whi ch gives the date of purchase. If you are sending the
item to M.T.H., fill out the Service Contact form in the Service Section of www.mth-railking.com; send US mail to the address
listed below; call 410-381-2580, or fax [phone] to obtain a return authorization number. If you are sending this product to an
Authorized Service Center, contact that Center for their return authorization.
This warranty gives you specific legal rights, and you may have other rights that vary from state to state.
Service Department
M.T.H. Electric Trains
7020 Columbia Gateway Drive
Columbia MD 21046-1532
A cover letter
including your name, address, daytime phone number, e-mail address (if available), Return Authorization number, a copy of
your sales receipt and a full description of the problem must be included to facilitate the repairs. Please include the description
regardless of whether you discussed the problem with a service technician when contacting the Service Center or M.T.H. for
your Return Authorization.
P
All M.T.H. products purchased from an Authorized M.T.H. Train Merchant are covered by this warranty.
a copy of the
original sales receipt from an Authorized M.T.H. Train Merchant
www.mth-railking.com

RailKing AeroTrain Locomotive 17
ALABAMA
ARIZONA
CALIFORNIA
COLORADO
CONNECTICUT
DELAWARE
FLORIDA
ILLINOIS
INDIANA
LOUISIANA
MAINE
MARYLAND
MASSACHUSETTS
MICHIGAN
SOUTHERLAND STATION
HUNTSVILLE
256-533-4720
[email protected]
ARIZONA TRAIN DEPOT
MESA
480-833-9486
[email protected]
www.arizonatraindepot.com/
DOLLHOUSES, TRAINS & MORE
NOVATO
415-883-0388
[email protected]
TIN PLATE JUNCTION
OAKLAND
510-444-4780
[email protected]
MIZELL TRAINS Inc
WESTMINSTER
303-429-4811
[email protected]
www.mizelltrains.com
SHELTON RAILROAD SYSTEMS
SHELTON
203-924-8761
[email protected]
NEW ENGLAND HOBBY SUPPLY
MANCHESTER
860-646-0610
[email protected]
K R R B MODEL TRAINS INC.
NEWARK
302-292-2779
[email protected]
www.krrb.com
DEPOT HOBBY SHOP
LAKE WORTH
561-585-1982
[email protected]
www.depothobbies.com
COLONIAL PHOTO & HOBBY
ORLANDO
407-841-1485
[email protected]
WARRICK CUSTOM HOBBIES
PLANTATION
954-370-0708
[email protected]
www.warrickcustomhobbies.com
FRANK'S TRAINS & HOBBIES INC.
OLDSMAR
813-855-1041
[email protected]
www.allhobbies.com
READY TO ROLL
MIAMI
305-688-8868
[email protected]
www.readytorolltrains.com
BIKE & CHOO CHOO CONNECTION
SCHAUMBURG
847-882-7728
[email protected]
Y. O. R. K. TRAINS
MUNSTER
219-838-9999
[email protected]
SAMUELSON'S TRAIN SHOP
VALPARAISO
219-462-2708
AMERICA'S TRAIN YARD
BATON ROUGE
225-926-5592
WHEELS, WINGS & THINGS
LUDLOW
207-532-6277
[email protected]
ENGINE HOUSE HOBBIES
GAITHERSBURG
301-590-0816
[email protected]
J & B TRAINS
HAGERSTOWN
240-420-4930
HOBBYTOWN U S A
FREDERICK
301-694-7395
PURKEY'S TOY TRAINS
SYKESVILLE
410-549-6061
[email protected]
THE TRAIN ROOM
HAGERSTOWN
301-745-6681
NORTHEASTTRAINS
PEABODY
978-532-1615
www.netrains.com
BRASSEUR ELECTRIC TRAINS INC.
SAGINAW
517-793-4753
[email protected]
www.traindoctor.com
PARTICIPATING RETAILER LIST
AUTHORIZED SERVICE CENTER
www.mth-railking.com
7020 Columbia Gateway Dr. - Columbia, MD 21046
Information: 410-381-2580 Fax: [phone]

18 RailKing AeroTrain Locomotive
MISSOURI
NEW HAMPSHIRE
NEW JERSEY
NEW YORK
NORTH CAROLINA
OHIO
PENNSYLVANIA
SWITCH STAND
SAINT LOUIS
314-781-4458
[email protected]
MARK TWAIN HOBBY CENTER
ST. CHARLES
636-946-2816
[email protected]
www.hobby1.com
TREASURED TOYS
SALEM
603-898-7224
[email protected]
www.treasured-toys.com
RAILROAD SPECIALTIES
HUDSON
603-882-5566
[email protected]
www.electric-trains.com
TRAINS & THINGS
TRENTON
609-883-8790
[email protected]
GRAND CENTRAL STATION
KEARNY
201-955-6200
[email protected]
HOBBYMASTERS, INC
RED BANK
732-842-6020
[email protected]
HOLLY BEACH TRAIN DEPOT
WILDWOOD
609-522-2379
[email protected]
COAST TRAINS AND COLLECTIBLES
WALL
732-556-9005
[email protected]
www.coasttrains.com
J & B TRAINS, INC.
MAPLE SHADE
856-414-0092
[email protected]
HOBBY SHOP
MATAWAN
732-583-0505
hobbyshopnj.com
ATLANTIC RAILS
HAMMONTON
609-567-8490
[email protected]
www.atlanticrails.com
COUNTRY AND STUFF
ANDOVER
973-786-7086
[email protected]
RIDGEFIELD HOBBY
RIDGEFIELD
201-943-2636
COLUMBUS TRAIN STATION
COLUMBUS
609-518-1800
AURORA RAILS & HOBBIES
EAST AURORA
716-652-5718
[email protected]
AMERICANA STORE
TIVOLI
845-757-4246
[email protected]
NASSAU HOBBY CENTER, INC.
FREEPORT
516-378-9594
[email protected]
KROSS HARDWARE
WEST BABYLON
631-669-3069
[email protected]
CITY DEPOT, INC.
NEW HAMPTON
845-374-3010
[email protected]
www.citydepot.com
DRY BRIDGE STATION
MOUNT AIRY
336-786-9811
[email protected]
www.drybridgestation.com
THE FREIGHT YARD
SMITHFIELD
919-934-6229
[email protected]
TRAINS LTD.
CHARLOTTE
704-566-9070
[email protected]
www.trainsltd.com
THE ROUNDHOUSE & BACKSHOP
CARY
919-465-0810
DIXIE UNION STATION
MASON
513-459-0460
[email protected]
www.dixieunionstation.com
RICK'S TOY TRAINS
TOLEDO
419-478-0171
T & K HOBBY SHOP
BRIDGEPORT
740-633-6607
[email protected]
www.tkhobbies.com
TRAINS-N- THINGS
CANTON
330-499-1666
[email protected]
PARMA HOBBY
CLEVELAND
216-741-6440
[email protected]
GLEN'S TRAIN SHOP
AKRON
330-253-6527
E & S TRAINS
AKRON
330-745-0785
GRAND PACIFIC JUNCTION
OLMSTEAD FALLS
440-235-4777
[email protected]
HUDSON TOY, TRAIN & HOBBY
HUDSON
330-653-2997
[email protected]
DAVIS ELECTRONICS
MILFORD
513-831-6425
[email protected]
www.davistrains.com
SANDY'S HOBBY'S & COLLECTIBLES
ELYRIA
440-365-9999
[email protected]
ERIE RAILWAY DEPOT
TROY
937-440-9972
[email protected]
CLEARVIEW TRAIN & HOBBY
LORAIN
440-277-4488
[email protected]
www.clearviewtrainandhobby.com
FAIRCHANCE PHARMACY
FAIRCHANCE
724-564-7817
[email protected]
www.hhs.net/fairchance

RailKing AeroTrain Locomotive 19
THE STATION
NEW CUMBERLAND
717-774-7096
[email protected]
BUSSINGER TRAINS
AMBLER
215-628-2366
[email protected]
www.icdc.com/~btrains
CHARLEROI SWEEPER CENTER
CHARLEROI
724-483-3397
AMERICAN HOBBY CENTER
ALIQUIPPA
724-378-3930
[email protected]
CRANBERRY HOBBY DEPOT
CRANBERRY TWP
724-776-3640
[email protected]
ALLENTOWN TOY TRAIN SERVICE
ALLENTOWN
610-821-0740
ON THE RIGHT TRACK
ALTOONA
814-942-4345
JIM'S TRAIN SHOP
HOMER CITY
724-479-2026
[email protected]
YE OLDE TRAIN & CHRISTMAS
SHOPPE
BOYERTOWN
610-369-0755
www.yeoldetrain.com
TOBY TYLER'S HOBBY CENTER
PITTSBURGH
412-653-5030
[email protected]
BUSTLETON TRAIN SHOP
PHILADELPHIA
215-698-7266
CHESTNUT TOYBOX
PHILADELPHIA
215-545-0455
[email protected]
THE CABOOSE
LEHIGHTON
570-386-5352
www.thecaboosehobbies.com
[email protected]
EMERALD TRAIN & HOBBY
GREENWOOD
864-223-2247
MODEL RAILROAD & HOBBY SHOP
MEMPHIS
901-384-6500
[email protected]
www.modelrailroadandhobby.com
HOBBY TIME
AMARILLO
806.352.9660
[email protected]
TRAIN DEPOT
MANASSAS
703-335-2216
NORGE STATION
WILLIAMSBURG
757-564-7623
[email protected]
NUTBUSH EXPRESS
VICTORIA
804-696-1902
[email protected]
TOY TRAIN CENTER
RICHMOND
804-288-4475
T S G HOBBIES
WARRENTON
540-347-9212
[email protected]
www.mnsinc.com/tripi/tsg.htm
CHESTERFIELD HOBBIES
MIDLOTHIAN
804-379-9091
[email protected]
www.chesterfieldhobbies.com
DAVIS HOBBY SUPPLIES
PORTSMOUTH
757-397-1983
[email protected]
www.davishobby.com
LOCUST GROVE TRAINS
LOCUST GROVE
540-854-8955
[email protected]
www.locustgrovetrains.com
PATRICK'S TRAINS
WHEELING
304-232-0714
[email protected]
www.patstrains.com
SOMMERFELD'S TRAINS
BUTLER
262-783-7797
[email protected]
www.sommerfelds.com
G B T V & TRAINS
GREEN BAY
920-496-9697
[email protected]
GRAMPA'S TRAIN SHOP
RICE LAKE
715-234-2996
[email protected]
THE TRAIN STORE
WAUKESHA
262-650-6675
HOBBY OUTLET
FOND DU LAC
920-924-3770
[email protected]
CREDIT VALLEY RAILWAY COMPANY
STREETSVILLE
905-826-1306
[email protected]
www.cvrco.com
TOY TRAIN WORKSHOP
CUMBERLAND
613-833-3125
[email protected]
www.toytrainworkshop.com
THE TRAIN ROOM
FERGUS
519-787-3280
SOUTH CAROLINA
TENNESSEE
TEXAS
VIRGINIA
WEST VIRGINIA
WISCONSIN
ONTARIO
CANADA