Raleigh Strada 5 User manual

QUICK
START
GUIDE
RALEIGH.CO.UK

RALEIGH.CO.UK
QUICK START GUIDE 2
Our fully trained mechanics have expertly built your new bike and have thoroughly
checked it for quality and safety according to our extremely high standards.
The key checks carried out by our mechanics are:
STANDARD BIKE
• Frame and fork inspected for any damage
• Headset adjusted
• Wheels are secured in frame and fork
• Wheels running true
• Gears setup
• Brakes setup
• All bolts checked for correct tightness
• Saddle is correctly tted
• Tyres inated
• Pre greased the pedal threads
• Reectors and bells tted
PLUS FOR E-BIKES
• Electrical system working
Your bike is then carefully packaged, minimising any risk of damage whilst in transit.
In order to deliver your bike the handlebars have been rotated and pedals removed.
You will nd the pedals and tools in your parts box to complete the setup
of your bike. All that is left to do is follow this simply quick start guide
that will enable you to complete the set up and enjoy your new bike.
YOUR NEW BIKE HAS ARRIVED!

RALEIGH.CO.UK
QUICK START GUIDE 3
For any further set up issues please consult the main manual, which is also provided
in the parts box or contact our support team. Our contact details can be found on the
back page of this guide.
E-BIKES
We may have also removed your E-Bike Display and placed it in the parts box
to protect it when the bike was being delivered to you. To attach the display and
for more information about your E-bike please refer to the separate E-bike manual.
Your bike will need a full charge before use.
FINAL STEPS
1.
ADJUST THE
HANDLEBAR
3.
ADJUST THE
SADDLE
HEIGHT
2.
FITTING THE
PEDALS

RALEIGH.CO.UK
QUICK START GUIDE 4
• Keeping the front wheel straight
turn the handlebars to the right
so the handlebars are 90 degrees
to the front wheel.
• Your bike will either have an
A-headset or a threaded headset.
• Follow the instructions below to
correctly tighten the relevant stem.
Using the multi tool provided tighten
the 2 stem clamp bolts shown as A and
B in the above photo Max. 6Nm unless
stated otherwise on the component.
Using the multi tool provided tighten the
bolt in the top of the stem shown as C in
the above photo. The bolt may be under
a rubber bung. Max. 15Nm unless stated
otherwise on the component.
1. HANDLEBARS
Once the stem bolts are tightened
the sticker can be removed.
FAILURE TO CORRECTLY TIGHTEN THE STEM MAY RESULT IN SERIOUS INJURY.
IF IN DOUBT, CONTACT SUPPOR[email protected].UK
You must not pull
the stem out further
than the limit mark.
This must not be visible.

RALEIGH.CO.UK
QUICK START GUIDE 5
300
Standard handlebar Dropped handlebar
If the brake levers aren’t in the correct
position loosen the stem bolts using the
multi tool provided. Rotate the bars to
the correct position and tighten each bolt
evenly. Max. 6Nm unless otherwise stated
on the component. Once fully tightened
there should be an even gap at the top
and bottom of the handlebar.
FAILURE TO CORRECTLY TIGHTEN THE STEM OR HANDLEBAR MAY RESULT
IN SERIOUS INJURY. IF IN DOUBT, CONTACT [email protected].UK
HANDLEBAR POSITION
We may have to rotate your handlebars to secure the bike in the box therefore,
check your brake levers are either around 30 degrees pointing down on a standard
handlebar or for a dropped handlebar the levers are pointing directly down.
Even gap top and bottom

RALEIGH.CO.UK
QUICK START GUIDE 6
It is very important to t the pedals correctly, each pedal has a specic side therefore
we have labelled the pedals and your crank arms with RIGHT and LEFT labels.
Using the 15mm pedal tool provided, t the pedal marked RIGHT to the right hand
crank arm also marked RIGHT. You will have to turn the tool clockwise to tighten the
pedal to the crank arm. It’s the same principle for the left however, this time you will
turn the tool anti- clockwise. Tighten max. 30Nm.
ONCE THE PEDALS ARE ATTACHED AND TIGHTENED THE RIGHT AND LEFT
STICKERS CAN BE REMOVED.
2. PEDALS

RALEIGH.CO.UK
QUICK START GUIDE 7
There are a few ways to set your
saddle height but a nice, simply way
is as follows—rotate one of the pedals
down to the lowest position, sit on the
bike and put your heel on the pedal.
In this position your knee should just
be locking out. Setting your saddle height
here allows for a slight bend in the knee
when pedalling with the ball of the foot
on the pedal.
Use the tool provided to loosen the seat
post clamp, adjust the saddle height then
re-tighten the seat post clamp. Your bike
may have a quick release here and
therefore you won’t have to use a tool.
3. SADDLE HEIGHT
Before your rst ride please check:
• The handlebars/stem are not loose
• The brakes are working eectively
• The tyres are inated
• The pedals are not loose
YOU MUST NOT PULL THE SEAT POST
OUT FURTHER THAN THE LIMIT MARK.
THIS MUST NOT BE VISIBLE.

RALEIGH.CO.UK
QUICK START GUIDE 8
Phone - 01773532691
Email—[email protected]
USEFUL REFERENCE INFORMATION
www.raleigh.co.uk RaleighbikesUK
raleighbikes @RaleighBikes_UK