Rally RE1338A User manual

167957 11.13.98 TR
PRINTED IN U.S.A.
/
ASSEMBLY/REPAIR
PARTS MANUAL
MODEL NO. RE1338A
Lawn Tractor
For Parts and Service, contact our authorized distributor: call 1-800-849-1297
For Technical Assistance: call 1-800-829-5886

2
CONTENTS OF HARDWARE PACK
Parts packed separately in carton
Parts Bag contents shown full size
Parts bag contents not shown full size
(1) Shoulder Bolt
5/16-18
(1) Washer 17/32 x 1-3/16 x 12 Gauge
(1) Lock Washer 1/2
(1) Hex Bolt 1/2-13 x 1
(2) Hex Bolts 1/4-20 x 3/4 (2) Keps Nut 1/4-20
(1) Locknut 3/8-24
(2) Sheet
Metal
Screws
#10-16 x 1/2
(1) Large Flat Washer
(2) Keys
Steering Wheel Insert
Steering Wheel
Adapter
Steering
Bushing
Slope Sheet
Steering
Boot
Seat
Parts Bag
Manual
Steering
Wheel

ASSEMBLY
3
Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes.
To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use
the correct tools as necessary to insure proper tightness.
TOOLS REQUIRED FOR ASSEMBLY
A socket wrench set will make assembly easier. Standard
wrench sizes are listed.
(1) 9/16" wrench (1) 3/4" wrench
(2) 7/16" wrenches Tire pressure gauge
(1) 1/2" wrench Utility knife
(1) 5/16" wrench
When right or left hand is mentioned in this manual, it
means when you are in the operating position (seated
behind the steering wheel).
TO REMOVE TRACTOR FROM CARTON
UNPACK CARTON
• Remove all accessible loose parts and parts cartons
from carton (See page 2).
• Cut, from top to bottom, along lines on all four corners
of carton, and lay panels flat.
• Check for any additional loose parts or cartons and
remove.
FIG. 1
TOROLLTRACTOROFFSKID(SeeOperator’s
Manual for location of controls)
• Pressliftleverplungerandraiseattachmentliftleverto
its highest position.
• Release parking brake by depressing clutch/brake
pedal.
• Place gearshift lever in neutral (N) position.
• Roll tractor backwards off skid.
• Remove banding holding discharge guard up against
tractor.
SHEET
METAL
SCREW
STEERING WHEEL
STEERING
WHEEL
ADAPTER
STEERING SHAFT
(ASSEMBLY
POSITION)
TAB SLOT
TAB
HOLE
TABS
STEERING
BUSHING
LARGE FLAT WASHER
STEERING SHAFT
(SHIPPING POSITION)
STEERING WHEEL INSERT
3/8-24 LOCKNUT
STEERING
BOOT
BEFOREROLLINGTRACTOROFFSKID
ATTACH STEERING WHEEL (See Fig. 1)
• Slide the steering bushing over the steering shaft.
• Raise steering shaft forward until screw holes in dash
line up with steering bushing. Install two (2) sheet
metal screws and tighten securely.
• Position steering boot over steering shaft.
• Place tabs of steering boot over tab slots in dash and
push down to secure.
• Slidesteeringwheeladapterontouppersteeringshaft.
• Positionfrontwheelsof the tractorso theyarepointing
straight forward.
• Position steering wheel so cross bars are horizontal
(left to right) and slide onto adapter.
• Assemble large flat washer and 3/8-24 locknut and
tighten securely.
• Snap steering wheel insert into center of steering
wheel.
• Remove protective materials from tractor hood and
grill.
IMPORTANT:CHECK FOR AND REMOVE ANY STAPLES
INSKIDTHATMAYPUNCTURETIRESWHERETRACTOR
IS TO ROLL OFF SKID.

ASSEMBLY
4
FIG. 2
FIG. 3
INSTALL SEAT (See Fig. 4)
Adjust seat before tightening adjustment bolt.
• Remove cardboard packing on seat pan.
• Place seat on seat pan and assemble shoulder bolt.
Tighten shoulder bolt securely.
• Assembleadjustmentbolt,lockwasherandflatwasher
loosely. Do not tighten.
• Lower seat into operating position and sit on seat.
• Slideseatuntilacomfortablepositionisreachedwhich
allows you to press clutch/brake pedal all the way
down.
• Get off seat without moving its adjusted position.
• Raise seat and tighten adjustment bolt securely.
FIG. 4
LOCK WASHER
LARGE FLAT
WASHER
SHOULDER
BOLT
SEAT PAN
SEAT
ADJUSTMENT
BOLT
HOW TO SET UP YOUR TRACTOR
CONNECT BATTERY (See Figs. 2 and 3)
CAUTION: Do not short battery termi-
nals by allowing a wrench or any other
object to contact both terminals at the
same time. Before connecting battery,
remove metal bracelets, wristwatch
bands, rings, etc.
Positive terminal must be connected
first to prevent sparking from acciden-
tal grounding.
• Removecardboard packing fromseatpanand lift seat
pan to raised position.
• Open battery box door and remove protective plastic.
• Remove terminal protective caps and discard.
• If this battery is put into service after month and year
indicated on label (label located between terminals)
charge battery for minimum of one hour at 6-10 amps.
• FirstconnectREDbatterycabletopositive(+)terminal
withhexboltandkepsnutasshown. Tightensecurely.
• ConnectBLACKgrounding cable tonegative(-)termi-
nal with remaining hex bolt and keps nut. Tighten
securely.
• Close battery box door.
Open battery box door for:
• Inspection for secure connections (to tighten hard-
ware).
• Inspection for corrosion.
• Testing battery.
• Jumping (if required).
• Periodic charging .
HEX BOLT
NEGATIVE
(BLACK)
CABLE
POSITIVE (RED)
CABLE
DISCARD
TERMINAL
PROTECTIVE
CAPS
KEPS
NUT
BATTERY
BOX DOOR
SEAT PAN

ASSEMBLY
5
CHECK TIRE PRESSURE
Thetires onyourtractor were overinflatedatthe factoryfor
shipping purposes. Correct tire pressure is important for
best cutting performance.
• Reducetirepressureto14PSIinfront tires and 12 PSI
in rear tires.
CHECK DECK LEVELNESS
Forbestcuttingresults,mowerhousingshouldbeproperly
leveled. See “TO LEVEL MOWER HOUSING” in the
Service and Adjustments section of operator's manual.
CHECK FOR PROPER POSITION OF ALL
BELTS
See the figures that are shown for replacing motion and
mower blade drive belts in the Service and Adjustments
section of operator's manual. Verify that the belts are
routed correctly.
CHECK BRAKE SYSTEM
After you learn how to operate your tractor, check to see
that the brake is properly adjusted. See “TO ADJUST
BRAKE”intheServiceandAdjustmentssectionofoperator's
manual.
✓ CHECKLIST
BEFORE YOU OPERATE AND ENJOY YOUR NEW
TRACTOR,WEWISHTOASSURETHATYOURECEIVE
THEBESTPERFORMANCEANDSATISFACTIONFROM
THIS QUALITY PRODUCT.
PLEASE REVIEW THE FOLLOWING CHECKLIST:
✓All assembly instructions have been completed.
✓No remaining loose parts in carton.
✓Battery is properly prepared and charged. (Minimum
1 hour at 6 amps).
✓Seat is adjusted comfortably and tightened securely.
✓All tires are properly inflated. (For shipping purposes,
the tires were overinflated at the factory).
✓Be sure mower deck is properly leveled side-to-side/
front-to-rear for best cutting results. (Tires must be
properly inflated for leveling).
✓Checkmowerand drive belts. Besuretheyare routed
properly around pulleys and inside all belt keepers.
✓Check wiring. See that all connections are still secure
and wires are properly clamped.
WHILELEARNINGHOWTOUSEYOURTRACTOR,PAY
EXTRAATTENTIONTOTHEFOLLOWINGIMPORTANT
ITEMS:
✓Engine oil is at proper level.
✓Fuel tank is filled with fresh, clean, regular unleaded
gasoline.
✓Become familiar with all controls - their location and
function. Operate them before you start the engine.
✓Be sure brake system is in safe operating condition.

SERVICE NOTES
6

7
TRACTOR - - MODEL NUMBER RE1338A
SCHEMATIC
BATTERY
FUSE 30 AMP.
IGNITION
SWITCH
RED RED
RED BLACK
IGNITION
UNIT
HEADLIGHTS
NON-REMOVABLE
CONNECTIONS REMOVABLE
CONNECTIONS
BLACK
BLACK BLACK
WHITE
WHITE
WHITE
RED
BLACK
ORANGE
BLACK
BROWN
BLACK
BLACK
BLACK
STARTER
M
SEAT SWITCH
(NOT OCCUPIED)
GROUNDING
CONNECTOR
ATT'MENT CLUTCH
(CLUTCH OFF)
CLUTCH / BRAKE
(PEDAL UP)
SOLENOID
BLACK
LIGHTING SYSTEM OUTPUT
5 AMP AC @ 3600 RPM
ALTERNATOR
14 VOLTS AC MIN. @ 3600 RPM (LIGHTS OFF)
DIODE
28 VOLTS AC MIN. @ 3600 RPM 
(CHARGING SYSTEM DISCONNECTED)
CHARGING SYSTEM OUTPUT
3 AMP DC @ 3600 RPM
NOTE
YOUR TRACTOR IS
EQUIPPED WITH A SPECIAL
ALTERNATOR SYSTEM.
THE LIGHTS ARE NOT 
CONNECTED TO THE
BATTERY, BUT HAVE THEIR
OWN ELECTRICAL SOURCE.
BECAUSE OF THIS, THE
BRIGHTNESS OF THE LIGHTS
WILL CHANGE WITH ENGINE
SPEED. AT IDLE THE LIGHTS
WILL DIM. AS THE ENGINE IS
SPEEDED UP, THE LIGHTS
WILL BECOME THEIR BRIGHTEST.
WIRING INSULATED CLIPS
NOTE: IF WIRING INSULATED CLIPS WERE REMOVED FOR
SERVICING OF UNIT, THEY SHOULD BE REPLACED TO
PROPERLY SECURE YOUR WIRING.
A
AMMETER
RED
GBSM
A1
A2
L
HOUR
METER
(OPTIONAL)
(OPTIONAL)
SPARK
PLUG
GAP
(2 PLUGS ON 
TWIN CYL. ENGINES)
IGNITION SWITCH
CIRCUITPOSITION
OFF B+A1RUN/LIGHT
B + S + A1START
M+G+A1
B+A1RUN
“MAKE”
A2+L
NONE
NONE
NONE

8
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
ELECTRICAL
28
29
26
24 42
43
44 44
25
41
19
20
19
20
40
33
22
21
30
48
16
16
8
2
1
27
52

9
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
ELECTRICAL
1 144925 Battery 12 Volt 25 Amp
2 74760412 Bolt Hex Hd 1/4-20unc X 3/4
8 156417 Case Battery
16 153664 Switch Interlock Push-In
19 10090400 Washer Lock 1/4
20 73350400 Nut Jam Hex 1/4-20 Unc
21 166181 Harness Asm Light W/4152J
22 4152J Bulb Light #1156
24 108423X Cable Battery 6 Ga 16"red
25 146147 Cable Battery 6 Ga red W/ 16" Wire
26 108824X Fuse 30 AMP Auto Green
27 73510400 Nut, Keps Hex 1/4-20 UNC
28 4207J Cable Ground 6 Ga 12" black
29 121305X Switch Plunger Nc Gray
30 163968 Switch, Ignition
33 140401 Key Ign
40 166151 Harness Ign
41 71110408 Bolt Blk Fin Hex 1/4-20 x 1/2
42 131563 Cover Terminal Red
43 145673 Solenoid
44 73640400 Nut Keps Hex 1/4-20 Unc
48 140844 Adapter Ammeter Rectangular
52 141940 Protection Wire Loop
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions give in U.S. inches
1 inch = 25.4 mm.

10
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
CHASSIS AND ENCLOSURES
3
5
3
2
3
38
39
35
26
14
4
14
13
35
26
33 10
34
3
6
3
3
14
3
15
11
1
8
16
16
9
21 22
17
21
29
28
14
4
7
54
19
24
26 25
26 25
3
31
24
30
18
140
3
145
37 37
3
3
161

11
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
CHASSIS AND ENCLOSURES
KEY PART
NO. NO. DESCRIPTION
1 165480 Chassis
2 140356 Drawbar
3 17490612 Screw, Thd., Roll. 3/8-16 x 3/4 Type-TT
4 19131216 Washer 13/32 x 3/4 x 16 Gauge
5 155272 Bumper Hood/Dash
6 155923 Saddle
7 124027X Shield Heat Hood LT
8 155138 Clip, Retainer Slide-On
9 166318X010 Dash
10 72140608 Bolt, Carriage 3/8-16 x 1
11 155927 Dashboard, panel LH
13 155934X010 Dashboard, panel RH
14 17490608 Hex head tread rolling screw 3/8-16 x 1/2 Ty-tt
15 74180512 Machine screw 5/16-18 unc x 3/4
16 73510500 Nut, Keps 5/16-18 Unc
17 154988X505 Hood Asm Pnt Weld Slope MS-505
18 126938X Bumper Hood
19 164863 Screw Hwhd Hi-Lo #13-16 x 3/4
21 122933X Rivet Ratchet Nylon
22 124479X Washer, Nylon Blk .28 x .75 x .19
24 74780616 Bolt, Hex Head, Fin. 3/8-16 x 1 Grade 5
25 19131312 Washer 13/32 x 13/16 x12 Gauge
26 73800600 Nut Lock Hex w/Ins. 3/8-16 Unc
28 140135X505 Grille
29 124029X599 Lens Grille
30 157583X505 Fender
31 136619 Fender Bracket
33 105476X505 Footrest, LH
34 105475X505 Footrest, RH
35 72110606 Bolt 3/8-16 X 3/4
37 17490508 Screw Thdrol 5/16-18 x 1/2
38 139886 Mower Pivot Bracket, LH
39 139887 Mower Pivot Bracket, RH
54 161464 Screw Hex WsHd 8-18 x 7/8
140 158418 Bracket Suspension Front
145 156524 Rod Pivot Chassis/Hood
161 161547 Extrusion Hood
- - 5479J Button Plug
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm

REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
DRIVE
12
29
28
112
14 41
42
40
38
42
39
89
57
51
51
74
75
7876
77
1
25
19 24
253
35
34
37
36 35
62
36
64
65
59
56
19 72
55
63
116
70
77
42
61
22 27
26
85
52
61
30 32 32 30 52
61
11
8580 4
3
13
84
42
145
79 6
113
18
51 518
6
52
66
96
26
69 81
21
8
10 169
82
156
165
168
166
163
14
159
161
160 158
164
83
162
27 51
48
150
151
50
49
26
47
50
51
6
170
171

REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
DRIVE
13
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 - - - - - - - Transaxle Peerless 205-544C
Order parts from transaxle
manufacturer
2 146682 Spring, Brake Return
3 123666X Pulley, Transaxle
4 12000028 Ring, Retainer
5 121520X Strap, Torque
6 17490512 Screw, Hex, Washer, Thread
Rolling 5/16-18 x 3/4
8 165619 Rod Shift Fender Adjust LT
10 76020416 Pin, Cotter 1/8 x 1
11 105701X Washer, Shift Plate
13 74550412 Bolt 1/4-28 UNF Gr. 8 w/Patch
14 10040400 Washer Lock
18 74780616 Bolt, Fin Hex 3/8-16 Unc x 1 Gr. 5
19 73800600 Locknut 3/8-16
21 106933X Knob
22 130804 Rod, Brake
24 73350600 Nut, Hex Jam 3/8-16
25 106888X Spring, Rod, Brake
26 19131316 Washer 13/32 x 13/16 x 16 Gauge
27 76020412 Pin, Cotter 1/8 x 3/4
28 145204 Rod, Brake, Park
29 71673 Cap, Plunger
30 130807 Bracket, Transaxle, L.H.
32 74760512 Bolt Hex Hd 5/16-18 UNC x 3/4
34 155071 Shaft, Foot Pedal
35 120183X Bearing Nylon
36 19211616 Washer 21/32 x 1 x 16 Gauge
37 1572H Pin,Roll 3/16 x 1
38 131494 Idler, Flat
39 74760644 Bolt, Hex 3/8-16 x 2-3/4
40 4470J Spacer
41 165838 Keeper, Belt
42 19131312 Washer 13/32 x 13/16 x 12 Gauge
47 127783 Pulley, Idler
48 154407 Bellcrank Clutch Grnf Drv Stl
49 123205X Retainer, Belt
50 74760624 Bolt, Hex 3/8-16 x 1-1/2
51 73680600 Nut, Crownlock 3/8-16
52 73680500 Nut, Crownlock 5/16-18
53 105710X Link, Clutch
55 105709X Spring, Return, Clutch
56 74760620 Bolt, Fin, Hex 3/8-16unc x 1-1/2
57 130801 V-Belt, Drive
59 140312 Retainer, Belt
61 17490612 Screw, Hex Washer Head, Thd.,
Roll. 3/8-16 x 3/4
62 8883R Cover, Foot Pedal
63 140186 Pulley, Engine
64 71170764 Bolt, Hex 7/16-20 x 4 Gr. 5
65 10040700 Washer, Lock Hvy Hlcl Spr 7/16
66 154778 Keeper, Belt Engine F-Proof
70 134683 Guide Belt Mower Drive RH
72 19132012 Washer 13/32 x 1-1/4 x 12 Ga.
74 137057 Spacer, Axle
75 121749X Washer 25/32 x 1-1/4 x 16 Ga.
76 12000001 E-Ring
77 123583X Key Square
78 121748X Washer 25/32 x 1-5/8 x 16 Ga.
79 2228M Key Woodruff #9 3/16 x 3/4
80 131486 Shift Arm
81 165594 Shaft Asm Cross Tapered
DA/PR 18
82 123782X Spring, Torsion
83 19171216 Washer 17/32 x 3/4 x 16 Gauge
84 166228 Link, Transaxle PMST/18" Zinc
85 150360 Nut 1/4-28
89 139963X428 Console Shift
90 124346X Nut, Washer Head, Self-Thread 1/4
96 4497H Retainer Spring 1" Ziinc/Cad
112 19091210 Washer 9/32 x 3/4 x 10 Ga.
113 127285X Strap Torque L.H. Lt
116 72110610 Bolt, RdHd Sq Neck 3/8-16 x 1.25
145 74490540 Bolt, Hex Flghd 5/16-18 Gr. 5
150 165850 Bushing, Bellcrank Grd Drive
151 19133210 Washer 13/32 x 2 x 10 Ga.
156 166002 Washer Srrted 5/16ID x 1 x .125
158 165589 Bracket, Shift Mount
159 165494 Hub, Tapered Flange Shift LT
160 19292016 Washer 29/32 x 1-1/4 x 16 Ga
161 72140406 Bolt Rdhd Sqnk 1/4-20 x 3/4 Gr 5
162 73680400 Nut, Crownlock 1/4-20 UNC
163 74780416 Bolt, Hex Fin 1/4-20 UNC x 1 Gr 5
164 19091010 Washer 5/8 x .281 x 10 Ga
165 165623 Bracket Pivot Lever
166 166880 Screw 5/16-18 x 5/8
168 165492 Bolt Shoulder 5/16-18 x .561
169 165581 Plate, Fastening LT
170 165849 Keeper, Belt, transaxle Gear
171 17490608 Screw Thdrol 3/8-16 x 1/2 TY-TT

REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
STEERING WHEEL
14
5
9
5
7
7
9
4
332
43
6
43
8
18
19
22
27
62
23
11
40 66
29
25
79
80
8
10
40
68
68
11
8
6
9
46
46
8
6
9
2
47
67
65
47
1
41
17
42
37
36
37
26
30
28
38
39
29
29
29
29
40
13
15

15
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
STEERING WHEEL
1 133741 Wheel, Steering
2 154427 Asm. Axle, Rear
3 156483 Asm., Spindle, Lh
4 157473 Asm., Spindle, Rh
5 6266H Bearing, Thrust, Hardened
6 121748X Washer 25/32 x 1-5/8 x 16 Ga.
7 19272016 Washer 27/32 x 1-1/4 x 16 Ga.
8 12000029 Ring, Clip
9 3366R Bearing
10 156438 Link, Drag
11 10040600 Washer, Lock
13 154779 Bearing, Axle
15 73901000 Nut, Jam Hex w/Washer Insert 5/8-11 UNC
17 156545 Asm. Shaft, Steering
18 57079 Washer, Thrust .515 x .750 x .033
19 160395 Support, Shaft
22 165857 Screw, Hex Wshhd Torx
23 165851 Shaft, Asm Pitman
25 154406 Bracket, Steering
26 126847X Bushing, Link, Drag
27 136874 Gear, Sector
28 19131416 Washer 13/32 x 7/8 x 16 Ga.
29 17490612 Screw, Thdrol 3/8-16 x 3/4 Type TT
30 76020412 Pin, Cotter
32 130465 Rod, Tie
36 155099 Bushing, Steering
37 152927 Screw
38 133742 Insert, Steering
39 19133808 Washer 13/32 x 2-3/8 x 8 Ga.
40 7810H Nut
41 104820X Adapter, Steering
42 124418X Boot, Shaft Steering Blk
43 121749X Washer 25/32 x 1-1/4 x 16 Ga.
46 121232X Cap, Spindle
47 6855M Fitting, Grease
62 167903 Kit, Steering Asm, Service
65 154780 Spacer Axle
66 154404 Bearing Arm Pittman
67 74781044 Bolt, FinHex 5/8-11 UNC x 2-3/4
68 154429 Axle, Brace
79 19132012 Washer 13/32 x 1-1/4 x 12 Ga.
80 74950612 Bolt, Hex Nylon 3/8-16 x 3/4
KEY PART
NO. NO. DESCRIPTION
NOTE: AllcomponentdimensionsgiveninU.S.inches
1 inch = 25.4 mm

16
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
ENGINE
2
1
OPTIONAL EQUIPMENT

Spark Arrester
29
44
46
32
31
33
37
33
40
62
13
4
85
14
38
15
78
78
81
3
16
35
23

17
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
ENGINE
KEY PART
NO. NO. DESCRIPTION
1 152141 Control Th/ch Flag EEC 15.1
2 17720410 Screw Hex Thd Cut 1/4-20x5/8 T
3 - - - - - - Engine Tecumseh Model OHV130
Order parts from engine manufacturer
4 156700 Muffler Tec 11/13.0 HP LT
13 165291 Gasket Eng 1 313 Id Tin Plated
14 13280336 Nipple Pipe 4-1/2"
15 13200300 Elbow Std 90 Degree 3/8-18 Npt
16 11050600 Washer Lock Ext Tooth 3/8
23 159880 Shield Brn/Dbr Guard
29 137180 Kit Spark Arrestor (Flat Scrn)
31 109202X Tank Fuel Front 2 00
32 140527 Cap Asm Fuel
33 123487X Clamp Hose Blk
35 17490512 Screw Thdrol 5/16-18 x 3/4 TYT
37 137040 Line Fuel
38 - - - - - Plug Oil Drain (Order From Engine Manufacturer)
40 124028X Bushing Snap Nyl Blk Fuel Line
44 17490412 Screw Hexwsh Thdrol 1/4-20x3/4
46 19091416 Washer 9/32 X 7/8 X 16 Ga
62 10040500 Washer 5/16
78 17490620 Screw Thdrol 3/8-16x1-1/4 TYTT
81 128861 Nut Flange 1/4-20 Starter Nut
85 123528X Bolt Hex Hd Phillips
NOTE: All component dimensions given in U.S. inches.
1 inch = 25.4 mm.

18
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
SEAT
1 127426X Seat
2 140551 Bracket, Pivot, Seat
3 74760616 Bolt
4 19131610 Washer 13/32 x 1 x 10 Ga.
5 145006 Clip, Push-in
6 73800600 Nut
7 124181X Spring, Seat
8 17490616 Screw, Thdrol 3/8-16 x 1
9 19131614 Washer 13/32 x 1 x 14 Ga.
10 155925 Pan, Seat
12 121246X Bracket, Mounting, Switch, Seat
13 121248X Bushing, Nylon
14 72050412 Nut, Crownlock 1/4-20 x 1-1/2
15 134300 Spacer, Split
16 121250X Spring
17 123976X Nut, Lock, Flange 1/4 Gr. 5
21 153236 Bolt, Shoulder 5/16-18 UNC
22 73800500 Nut
23 74780814 Bolt Fin Hex 1/2 - 13 x 7/8 Gr. 5
24 19171912 Washer 17/32 x 1-3/16 x 12 Ga.
25 127018X Bolt Shoulder 5/16-18 x .62
26 10040800 Washer Lock Hvy Hclc Spr 1/2
KEY PART
NO. NO. DESCRIPTION KEY PART NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
26
23
1
24
16
15
12
13
17
25
4
3
8
9
7
8
9
7
2
622
21
5
10
5
14

19
REPAIR PARTS TRACTOR - - MODEL NUMBER RE1338A
DECALS
KEY PART
NO. NO. DESCRIPTION
3
25414
19
11
KEY PART
NO. NO. DESCRIPTION
6
9
1 159736 Decal, Chassis Hot Muffler
2 132628 Decal, Fender Logo
3 142308 Decal, Hood Rh
4 142309 Decal, Hood Lh
5 167611 Decal, HP Hood
6 145498 Decal, Read Owner's Manual Syms
7 145437 Decal, Europe Stand CE
8 159737 Decal, Brake/Clutch Symbol LT
9 64-1726-29 Decal, HP Engine
10 127900 Decal Chassis 38"
11 145494 Decal, Mower Cutfinger Symbol
12 135013 Decal, Enviro Deck Yellow
13 127075 Decal Wheel Steering
14 145005 Decal, Battery Dan/Poi P/L Symbols
15 136832 Decal, V-Belt
17 126187X Decal, 100 DBA
19 140837 Decal, Parking Brake
- - 138311 Decal, Handle, Lift, Height Adjust (Lift
Handle)
- - 162598 Decal, Drawbar Load Limit
- - 167956 Manual, Operator's (European)
-- 167955 Manual, Operator's (Scand)
- - 167957 Manual, Repair Parts
10
5
10
13
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
7
17
15
TIRES AND WHEELS
6
2
15,8
4,10
3,9
11
7
KEY PART
NO. NO. DESCRIPTION
1 59192 Cap, Valve
2 65139 Stem, Valve
3 106222X Tire Front
4 59904 Tube, Front (not furnished)
5 106732X427 Rim, Asm. Front
6 278H Grease Fitting (rear tire only)
7 9040H Bearing, Flange (front tire only)
8 106108X427 Rim, Asm. Rear
9 124635X Tire, Rear
10 7152J Tube, Rear (not furnished)
11 104757X Cap, Axle
- - 144334 Sealant, Tire (10 oz. Tube)
8
1
1
12