RAMTONS RM/476 User manual

FAN HEATER
MODEL: RM/476
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2015
Attention: Pictures in the IM are for reference only.
GD Midea Environment Appliances MFG. Co.Ltd.
No.28,Dong Fu Road,HeSui East Industrial Area,Dong Feng Town,
ZhongShan,GuangDong,China.
OWNER’S MANUAL

1
IMPORTANT SAFEGUARDS
When using any electrical appliance, basic safety
precautions should always be followed, including the
following:
1. To ensure Familiarity with the controls, safety features,
and operation of your heater -Read all instructions before
using.
2. Do not insert foreign objects through the intake or
discharge grilles.
3. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
4. Disconnect the cord from the outlet before cleaning. A
heater should never be used under conditions where it
may be immersed, or come in contact with water.
Similarly do not plug in your heater if its surfaces are
damp.
5. Do not use the appliance on the same socket or electric
circuit with other electrical appliances so as to prevent
the circuit from being overloaded, which will cause fire.
Please do not prolong the power cords by yourself or use
movable socket.
6. Unplug heater by grasping plug and pulling it from the
outlet. NEVER YANK ON CORD.
7. If the supply cord is damaged, it must be replaced by its
service agent or a similar qualify person in order to avoid
hazard.

2
8. Do not use in locations when the heater will be left
unattended for long periods of time. (for example -
several weeks in an unoccupied summer cottage)
9. Do not use attachments not recommended and sold by
MIDEA distributor.
10. Loose connections between the heater plug and the
electrical outlet may cause the plug to overheat.
11. Ensure no other appliances are plugged into the same
circuit as your heater. A circuit overload could occur
resulting in dimmed lights, blown fuses, tripped circuit
breakers, or fire hazard.
12. The heater is intended for household indoor use only.
13. The heater must not be located immediately below a
socket-outlet.
14. Warning: In order to avoid overheating, do not cover
the heater.
15. The heater is to be installed so that switches and other
controls cannot be touched by a person in the bath or
shower.
16.
17. Children of less than 3 years should be kept away unless
continuously supervised. Children aged from 3 years and
less than 8 years shall only switch on/off the appliance
provided that it has been placed or installed in its intended
normal operating position and they have been given
Correct Disposal of this product
This marking indicates that this product should not be disposed with
other household wastes throughout the EU. To prevent possible
harm to the environment or human health from uncontrolled waste
disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return
and collection systems or contact the retailer where the product was
purchased. They can take this product for environmental safe
recycling.

supervision or instruction concerning use of the appliance
in a safe way and understand the hazards involved.
Children aged from 3 years and less than 8 years shall
not plug in, regulate and clean the appliance or perform
user maintenance.
18. CAUTION — Some parts of this product can become
very hot and cause burns. Particular attention has to be
given where children and vulnerable people are present.
19. The heater must be installed at least 1.8m above the
floor.
3
WARNING: IN ORDER TO AVOID OVERHEATING,
DO NOT COVER THE HEATER.
Power swicth knob
Thermostat knob
Pilot lamp
Air outlet grille
Drill 2 holes into the wall with the horizontal distance of 18.5cm，insert a expansion
plugs and a bolt into each hole.The explored length of the bolts should be over
30mm.
Hang the heater on the wall by the bolts, and make sure that the holes of the
heater’s rear cover can match the bolts firmly.
INSTALLATION
OPERATING INSTRUCTIONS

4
18.5cm 18.5cm
3. Set the power switch to LOW position for fast warm up of a room. Once the room
is Comfortable, select a lower setting to reduce electrical consumption and to
prevent the room from becoming too warm.
4. Adjust the thermostat to maximum and select the desired power setting. Once
the room is comfortable, rotate the thermostat counterclockwise, until the heater
shuts off. The thermostat will now maintain the temperature by cycling the heater
on or off. During particularly cold weather, the low power setting may be
insufficient to satisfy the thermostat. Select a higher setting for these periods.
1. Plug into any 220-240VAC, 50Hz source (see important safeguards section
3.3 regarding use of extension cords).
2. Your heater is equipped with a 3-position power switch:
OPERATING INSTRUCTION
FUNCTION
POWER OFF
FAN ONLY
1200 WATTS
2000 WATTS
SYMBOL
OFF
LOW
HIGH
Attention:
1. The holes of the wall and the holes of the heater’s rear cover should be on the
same horizon line.
2. Keep the distance between flank wall and the heater more than 50CM, and there
is no other blockings within the distance of 60CM above and below the heater, in
order to make the heating air ventilate.
3. The mounting height should be more than 180CM.
4. When used near bathroom or swimming pool, do not drop the unit into bathtub or
swimming pool.
5. The mounting position should be far away from bathtub, shower nozzle and
swimming pool, and make sure that people in the area of bathtub or shower
could not reach the power switch or control device of the unit.

5
Your heater is fitted with a safety device "Double Protector" that (1) switches off
the heater by thermal cut-off in the event of overheating or malfunction, It will
reset while the temperature reduce to a normal level. (2) Shuts off the heater by
thermal fuse in the event of overheating or malfunction and not operates by some
other accidental reason.
If overheating or malfunctions continue, return the heater to an Approved Service
Agent for examination.
The most common cause of overheating is deposits of dust or fluff entering the
heater, Ensure these deposits are removed regularly by unplugging the unit and
vacuum cleaning air vents and front grille.
SAFETY CONTROL
1. Light accumulated dust may be removed from the heater with a soft cloth. Wipe
the exterior surfaces of the heater occasionally with a cloth moistened (not
dripping wet) with a solution of mild detergent and water. Dry the case
thoroughly with a soft dry cloth before operating the heater.
2. The fan motor is lubricated by the factory, and will require no further lubrication.
3. No other user maintenance is required or recommended. If service is required,
send your heater to the nearest authorized service depot.
4. Store heater in a clean and dry place when not in use.
REMEMBER - portable electric heaters are designed for spot heating, or as a
supplementary heat source. They are not intended to be main sources of heat
during the normal heating season.
Note: There may be trace of smoke or odour when unit is first operated. Do not
be alarmed. This indicates that a drop of oil fell on the heating coil during the
manufacturing process. It will quickly evaporate, and should not re-occur.
READ AND SAVE THESE INSTRUCTIONS
CLEANING AND MAINTENANCE
This fan heater is equipped with a pilot light that glows whenever the heater is
plugged in and turned on. It will continue to glow even if the thermostat has cycled
the heating elements off. This feature is to prevent you from being unaware that
the heater is operating and maintaining the temperature of the room.
When you do not wish the heater to control the room temperature, turn the control
switch to O (off) and remove the plug from the electrical outlet.
PILOT LIGHT