Range Master RM61000EX series User manual

RM61000EX
Series
Broan-NuTone LLC. 926 West State Street, Hartford, WI 53027
NuTone, Inc., 4820 Red Bank Road, Cincinnati, OH 45227
Broan-NuTone Canada, INC.1140 Tristar Drive, Mississauga, Ontario, L5T 1H9
ENGLISH.....................................2
FRANÇAIS................................13
ESPAÑOL...................................24

- 2 -
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
1. Usethisunitonlyinthemannerintendedbythemanufacturer.Ifyouhavequestions,
contactthemanufacturerattheaddress or telephonenumberlisted in thewarranty.
2. Before servicing or cleaning unit, switch power off at service panel and lock service
panel to prevent power from being switched on accidentally. When the service
disconnectingmeanscannotbelocked,securelyfastenaprominentwarning device,
suchasatag,totheservicepanel.
3. Installation work and electrical wiring must be done by a qualified person(s) in accor-
dancewith all applicable codesandstandards, including fire-ratedconstructioncodes
andstandards.
4. Sufficientairis neededfor propercombustion andexhausting ofgasesthroughtheflue
(chimney)of fuelburningequipment topreventbackdrafting. Followthe heating equip-
mentmanufacturer’sguidelinesand safety standards such as those published by the
National Fire Protection Association (NFPA), and the American Society for Heating,
RefrigerationandAir ConditioningEngineers(ASHRAE), andthelocalcodeauthorities.
5. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other
hiddenutilities.
6. Ductedfansmust always be vented totheoutdoors.
7. Donotuse this unit withanyseparate solid-state speed controldevice.
8. Toreducetheriskof fire, use only metal ductwork.
9. Thisunitmust begrounded.
TOREDUCE THE RISKOF A RANGETOPGREASE FIRE:
A. Never leave surface units unattended at high settings. Boilovers cause smoking and
greasyspillovers that mayignite.Heat oilsslowlyon low ormediumsettings.
B. Alwaysturn hood ON when cooking at high heat or when flambeing food (i.e. Crepes
Suzette,Cherries Jubilee, Peppercorn Beef Flambe’).
C. Cleanventilatingfansfrequently.Greaseshouldnot beallowedtoaccumulateonfanor
filter.
D. Use proper pan size. Always use cookware appropriate for the size of the surface
element.
WARNING
TOREDUCETHE RISK OF INJURY TO PERSONS INTHEEVENTOF A RANGE TOP
GREASEFIRE,OBSERVE THEFOLLOWING:*
1. SMOTHERFLAMESwithaclose-fitting lid,cookie sheet,or metaltray, thenturn offthe
burner.BE CAREFULTOPREVENT BURNS.Ifthe flamesdo not goout immediately,
EVACUATEANDCALLTHEFIREDEPARTMENT.
2. NEVERPICKUP AFLAMINGPAN -You maybeburned.
3. DONOTUSE WATER,including wetdishcloths ortowels-violentsteam explosionwill
result.
4. Useanextinguisher ONLY if:
A. YouknowyouhaveaClassABCextinguisherandyoualreadyknowhow tooperate
it.
B. Thefireissmall and containedinthe area whereitstarted.
C. The firedepartmentisbeingcalled.
D. You can fight the firewithyourback to an exit.
*Based on “KitchenFireSafety Tips”publishedby NFPA.
!
INTENDED FOR DOMESTIC COOKING ONLY
!

- 3 -
!
CAUTION
1. Toreduceriskoffireandtoproperly exhaustair,besuretoductairoutside.Donot vent
exhaustair intospaces withinwallsor ceilingsorinto attics,crawl spaces,orgarages.
2. Takecarewhen using cleaningagentsor detergents.
3. Avoidusingfood productsthatproduce flames underthe Range Hood.
4. Forgeneralventilating use only.Donot usetoexhaust hazardous orexplosivemate-
rialsandvapors.
5. Toavoidmotor bearingdamage andnoisyand/or unbalancedimpellers, keepdrywall
spray,constructiondust, etc. off power unit.
6. Yourhoodmotor hasa thermaloverload whichwillautomaticallyshutoff themotor ifit
becomesoverheated.Themotorwillrestartwhen itcools down.If themotor continues
toshutoff and restart, have the hood serviced.
7. Forbestcaptureofcooking impurities,the bottomof thehood shouldbeaminimumof
24"and a maximum of30"above the cooking surface.
8. Twoinstallersare recommended becauseofthe largesizeand weight ofthishood.
9. Thisproductisequipped with a thermostat which may start blower automatically. To
reduce the risk of injury and to prevent power from being switched on accidentally,
switchpoweroff at service panel and lock or tag service panel.
10. Pleasereadspecificationlabel onproduct forfurtherinformation andrequirements.
11. To reduce the risk of fire and electric shock, install this range hood only with Broan
Exteriorblowermodels331H,332H,335or336,orBroanIn-LineBlowermodelsHLB3,
HLB6,HLB9orHLB11.OtherBlowerscannotbesubstituted(Blowerssoldseparately).

- 4 -
PREPARE THE HOOD
Unpack hood and check contents.
You should receive:
1 - Hood
1 - Decorative Flue Assembly
1 - Flue Mounting Bracket
1 - Parts Bag (B08081196) containing:
2 - Mounting Brackets
8 - Mounting Screws (4,8 x 38mm Pan Head)
4 - Mounting Screws (3,9 x 9,5mm Pan Head)
4 - Mounting Screws (3,9 x 9,5mm Pan Head Black)
8 - Drywall Anchors
1 - Installation Instructions
MOUNTING
BRACKETS
FLUE MOUNTING
BRACKET
8 MOUNTING SCREWS
(4,8 x 38mm Pan Head) 8DRYWALL
ANCHORS
4 MOUNTING
SCREWS (3,9 x
9,5mm Pan Head)
DECORATIVE
FLUE
4 MOUNTING
SCREWS (3,9 x
9,5mm Pan Head -
Black)

- 5 -
EXTERIOR OR IN-LINE BLOWER SELECTION
CAUTION: Either an exterior blower or in-line blower may be used with this hood.
TheRM61000EXhoodmustbeinstalledwithblowermodels331H,332H,335,336,
HLB3, HLB6, HLB9 or HLB11 only. Other Blowers cannot be substituted (Blowers
sold separately).
TheblowermustbeULlistedforCanadianandU.S.use,andevaluatedforusewith
solid state speed control, rated 120V, 60 Hz, 6.0 A max.
HOOD
24” TO 30” ABOVE
COOKING SURFACE
DECORATIVE
FLUE
8” ROUND
DUCT
INSTALL THE DUCTWORK
NOTE: To reduce the risk of fire, use only metal ductwork.
1. Choose the location where the Exterior or In-Line Blower will be mounted. See
illustrations below for mounting location suggestions and restrictions.
2. A straight, short duct run will allow the hood to perform most efficiently.
3. Long duct runs, elbows and transitions will reduce the performance of the
hood. Use as few of them as possible. Larger ducting may be required for best
performance with long duct runs.
4. After the Exterior or In-Line Blower has been installed, connect round metal
ductwork and work back towards the hood location. Use duct tape to seal joints
between ductwork sections.
5. An 8” round to 10” round transition (Model 414) is required. For best air
performance, install the transition as close to the range hood as possible.
OK
OK
SUGGESTED MOUNTING LOCATIONS
EXTERIOR BLOWER
CAUTION: MAY NOT FIT
UNDER EAVES OF SINGLE
STORY HOMES
EXTERIOR
BLOWER
10” ROUND
DUCT
EXTERIOR
BLOWER
8” TO 10”
ROUND
ADAPTER
8” ROUND
ELBOW
10”
ROUND
DUCT

- 6 -
INSTALL MOUNTING
BRACKETS
1. Construct wood wall framing that is flush
with interior surface of wall studs.Make
sure:
a) theframing is centeredover installation
location.
b) the height of the framing will allow the
mounting brackets to be secured to
the framing within the dimensions
shown.
2. Afterwallsurfaceisfinished,secure mount-
ing brackets to framing using dimensions
shown.
FRAMING BEHIND DRYWALL
29-7/8” to 35-7/8” above
cooktop
29-7/8" = bottom of hood 24"above cooktop
35-7/8"= bottom of hood 30" above cooktop
36” MODEL
FRAMING BEHIND DRYWALL
29-7/8” to 35-7/8” above
cooktop
29-7/8" = bottom of hood 24"above cooktop
35-7/8"= bottom of hood 30" above cooktop
11-13/16”
48” MODEL
19-11/16”
IN-LINE BLOWER

- 7 -
DEPTH ADJUSTMENT
SCREWS
WIRING
Note: This range hood must be properly
grounded. The unit should be installed by a
qualified electrician in accordance with all
applicable national and local electrical
codes.
GROUNDING INSTRUCTIONS
Thisappliancemust be grounded.Intheevent
of an electrical short circuit, grounding
reduces the risk of electric shock by providing
an escape wire for the electric current. This
appliance is equipped with a cord having a
grounding wire with a grounding plug. The
plug must be plugged into an outlet that is
properly installed and grounded.
WARNING - Improper grounding can result in a risk of electric shock.
Consult a qualified electrician if the grounding instructions are not completely
understood, or if doubt exists as to whether the appliance is properly grounded.
Do not use an extension cord. If the power supply cord is too short, have a qualified
electrician install an outlet near the appliance.
Set the electrical power supply within the space covered by the decorative flues.
Position the power socket at a maximum distance of 33-7/16” (85 cm) from where
the lead exits from the hood (see illustration alongside). Make sure this does not
interfere with the decorative flues (where the flue touches the wall).
Fit the plug into the power socket.
INSTALL THE HOOD
1. Hang the hood from the brackets through
the rectangular cut-outs on the back of
the hood. Cut-outs are larger than the
bracketsto allow forhorizontal adjustment.
The bottom of the hood should be 24" to
30" above the cooking surface.
2. Heightadjustmentscrews providevertical
adjustment.
3. Depth adjustment screws provide hori-
zontal adjustment.
4. Secure the hood with mounting screws
(4,8x38mm). Use drywall anchors,
provided, if wall studs or framing are not
available.
MOUNTING
SCREWS
(4,8x38mm)
MOUNTING
BRACKETS
HEIGHT ADJUSTMENT
SCREWS
WALL FRAMING
MOUNTING SCREWS
(4,8x38mm)
RECTANGULAR
CUTOUTS
MOUNTING SCREWS
(4,8x38mm)
33-7/16”
(85cm)max

- 8 -
FASTEN FLUE TO HOOD AND BRACKET
WITH MOUNTING SCREWS (3,9x9,5mm)
8" ROUND
METAL DUCT
DECORATIVE
FLUE
DUCT TAPE
FLUE MOUNTING BRACKET
CONNECT DUCTWORK
1. Use mounting screws (4,8x38mm) and
drywall anchors to secure flue mounting
bracket to the ceiling and wall as shown.
2. Use 8" round metal duct to connect the
discharge collar on the hood to the
ductwork above.
3. Use duct tape to make all joints secure
and air tight.
4. Connect the upper flue to the bracket with
mounting screws (3,9x9,5mm).
5. Slide the lower flue downward, until it fits
properly around hood.
6. Secure lower flue to hood with mounting
screws (3,9x9,5mm).
MOUNTING
SCREWS
(4,8x38mm)
Exterior or In-Line
blower
Blowerconnectionathood:
1. Run 2-wire plus ground power cable from
the exterior or In-Line blower to the hood’s
wiring box marked “motor connection”.
2. Removethe cover fromthewiring box and
remove one knockout.
3. Feed 6” of cable through the knockout
openingand secure thecableto the wiring
box with an appropriate connector.
4. Make electrical connections at the hood.
Connect white-to-white, red-to-black and
green-to-ground.
5. Replace the wiring box cover and screws.
make sure wires are not pinched between
the cover and box.
Exterior or In-Line blower connection:
1. Makeelectricalconnectionsattheexterior
orIn-Lineblower(seeinstructionsprovided
with the exterior or In-Line blower).
Powerconnection at hood:
1. Plug the power cord into the electrical wall
receptacle.
BLOWER CONNECTION AT HOOD
BOX MARKED
“MOTOR
CONNECTION”
CONNECT:
WHITE-TO-WHITE,
RED-TO-BLACK,
GREEN-TO-GROUND.

- 9 -
MAINTENANCE
Proper maintenance of the Range Hood will
assure proper performance of the unit.
Grease Filters
The grease filters should be cleaned fre-
quently.Useawarmdetergentsolution.Grease
filters are dishwasher safe.
Removefilterbypushingfiltertowardsthe back
of hood and rotating filter downward.
Hood Cleaning
Stainless steel is one of the easiest materials
to keep clean. Occasional care will help pre-
serve its fine appearance.
Cleaning tips:
OHot water with soap or detergent is all that is usually needed.
OFollow all cleaning by rinsing with clear water. Wipe dry with a clean, soft cloth
to avoid water marks.
OFor discolorations or deposits that persist, use a non-scratching household
cleanser or stainless steel polishing powder with a little water and a soft cloth.
OFor stubborn cases, use a plastic scouring pad or soft bristle brush together
with cleaser and water. Rub lightly in direction of polishing lines or "grain" of the
stainless finish. Avoid using too much pressure which may mar the surface.
ODO NOT allow deposits to remain for long periods of time.
ODO NOT use ordinary steel wool or steel brushes. Small bits of steel may
adhere to the surface causing rust.
ODO NOT allow salt solutions, disinfectants, bleaches, or cleaning compounds
to remain in contact with stainless steel for extended periods. Many of these
compounds contain chemicals which may be harmful. Rinse with water after
exposure and wipe dry with a clean cloth.
Painted surfaces should be cleaned with warm water and mild detergent only.
GREASEFILTERS

- 10 -
OPERATION
Controls
The hood is operated using the slide controls
under the front edge of the hood.
The light switch turns the halogen lights on
and off.
The blower on / off switch turnsthe bloweron
to the running speed set by the blower speed
control. The blower must be turned on and off
using this switch.
The blower speed control changes the speed
of the blower from 1 to 3 position.
The pilot lamp lights up whenever the blower is on.
HEAT SENTRY™
Your hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a
device that will turn on or speed up the blower if it senses excessive heat above
the cooking surface.
1) If blower is OFF - it turns blower ON to HIGH speed.
2) If blower is ON at a lower speed setting - it turns blower up to HIGH speed.
When the temperature level drops to normal, the blower will return to its original
setting.
WARNING
The HEAT SENTRY thermostat can start the blower even if the hood is turned
OFF. When this occurs, it is impossible to turn the blower OFF with its switch.
If you must stop the blower, do it from the main electrical panel.
LIGHT
SWITCH
PILOT
LAMP
BLOWER
SPEED
CONTROL
BLOWER
ON / OFF
SWITCH
HALOGEN BULBS
Thisrange hood requires2 or 4halogenbulbs
(Type JC, 12Volt, 20Watt Max, G-4 Base).
ALWAYS SWITCH OFF THE ELECTRICITY
SUPPLY BEFORE CARRYING OUT ANY
OPERATIONSONTHEAPPLIANCE.
To change bulbs:
1. Loosen the ring nut by turning it
counterclockwise.
2. Pull the bulb downwards to remove - DO
NOTROTATE.CAUTION: BULB MAY BE
HOT!
3. ReplacewithType JC, 12Volt, 20WattMax,
G-4 Base halogen bulb. Do not touch
replacement bulb with bare hands!
RING NUT

- 11 -
FUSE REPLACEMENT
SWITCHOFF THEELECTRICITY SUPPLY.
Remove the grease filters.
Remove the electrical box support and open
the electrical box.
Replace with the same type of fuse (5x20mm,
5A, 125V).
ELECTRICAL
BOX
SUPPORT
FUSE
ELECTRICAL
BOX

- 12 -
BROAN-NUTONE LLC ONE YEAR LIMITED WARRANTY
Broan-NuToneLLC warrantsto the originalconsumer purchaserof itsproducts thatsuch productswill befree fromdefects
in materials or workmanship for a period of one year from the date of original purchase. THERE ARE NO OTHER WAR-
RANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, IMPLIED WARRANTIES OR MERCHANT
ABILITY OR FITNESS FOR A PARTICULAR PURPOSE.
Duringthis one-yearperiod,Broan-NuTone LLCwill,atitsoption, repairorreplace, withoutcharge,anyproductor partwhich
isfound to bedefective undernormal useand service.
THIS WARRANTY DOES NOT EXTEND TO FLUORESCENT LAMP STARTERS, TUBES, HALOGEN AND
INCANDESCENDTBULBS. This warrantydoes notcover (a)normal maintenanceand serviceor (b)any productsor parts
whichhavebeen subjecttomisuse,negligence, accident,impropermaintenanceorrepair(otherthan byBroan-NuToneLLC),
faultyinstallationor installationcontrary to recommendedinstallation instructions.
Theduration ofany impliedwarranty islimited tothe one-yearperiod asspecified forthe expresswarranty. Some statesdo
not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
BROAN-NUTONE LLC’S OBLIGATION TO REPAIR OR REPLACE, AT BROAN-NUTONE LLC’S OPTION, SHALL BE
THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. BROAN-NUTONE LLC SHALL
NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNEC-
TION WITH PRODUCT USE OR PERFORMANCE. Some states do not allow the exclusion or limitation of incidental or
consequentialdamages, so theabove limitationor exclusionmaynot applyto you.
Thiswarranty givesyouspecific legalrights,and youmayalso haveotherrights, whichvaryfrom statetostate. This warranty
supersedes all prior warranties.
Toqualify forwarranty service,youmust (a)notify Broan-NuToneLLC attheaddressstatedbelow ortelephone: 1-800-637-
1453,(b) givethe modelnumberand partidentification and(c)describe thenature ofany defectinthe productor part. Atthe
timeof requesting warrantyservice, youmustpresent evidenceof the originalpurchase date.
Broan-NuToneLLC.926WestStateStreet,Hartford,WI53027(1-800-637-1453)
NuTone,Inc.,4820RedBankRoad,Cincinnati,OH45227(1-800-543-8687)
Broan-NuToneCanada,Inc.1140TristarDrive,Mississauga,Ontario,L5T1H9(1-888-882-7626)
WARRANTY

- 36 -
SERVICE PARTS
MODEL RM61000EX - Parts for stainless steel models shown. For service parts for
black, white, polished brass, or brushed copper models, call Broan Customer
Service.
KEY NO. PART NO. DESCRIPTION
9 B08087135 Grease Filter (n.3) - 36” model
9 B08087136 Grease Filter (n. 4) - 48” model
16 BE3345326 Electrical Box Support
19 B03295005 Transformer Protection
26 B02300891 Halogen Lamp Bulb
30 B03292291 Controls Protection
37 B02300787 Heat Sentry
39 B03294033 Electrical Box Cover
56 B03292465 Discharge collar
57 B02011004 Damper Flap
60 B02300249 Feeder Cable
113 B03202433 Nameplate
115 BE3495228 Wiring Box
116 BE3334252 Wiring Box Cover
118 BE3341301 Decorative Flue Bottom
119 BE3341311 Decorative FlueTop
120 BE3300517 Flue Mounting Bracket
144 B03292287 Wire Clamp
145 B032920170 Feeder Cable Connection Box
146 B032920180 Feeder Cable Connection Box Cover
147 BR2300132 Junction Clamp
151 B032920200 Electrical Box Wires Stop
165 B03294781 Electrical Box
165 B03295008 Electrical Board Box
166 B08086141 Electrical Board
166 B08086668 Electrical Board
195 BE3403629 Upper Support
208 B02300783 Transformer (36” Model)
208 B02300729 Transformer (48” Model)
223 B03202294 Switch Button
407 B08091607 Support
472 BE3345233 Wiring Box Support
474 B02300789 Halogen Lamp Housing
477 B03295006 Transformer Protection Cover
998 B08081196 Hardware Package
* B06108080 Switch Box Assembly for model 48”
(Includes Keys No. 222, 229, 223, 224, 225,
226, 227, 228, 230)
* B06108083 Switch Box Assembly for model 36”
(Includes Keys No. 222, 229, 223, 224, 225,
226, 227, 228, 230)
* B08085018 Damper Assembly (Includes Key Nos 56, 57)
- B02300782 Fuse
- B02300674 Fuse Holder
* Not shown assembled.

- 39 -
SERVICE PARTS - LISTE PIECES DE RECHANGE -
LISTA DE PIEZAS DE RECAMBIO
MODEL 61000 EX