Raptor Series MAGNUM RT Series User manual

Your satisfaction is important to us, please let us help!
If you have any questions or concerns during the installation, our support representa-
tives are available to assist you.
Please call: 1-877-769-3765 or Live Chat at www.raptorseries.com
If you have damaged or missing parts please contact the company you purchased the
product from and notify them of the issue right away.
CAUTION: Do not install damaged parts!!!
Raptor Series Truck Accessories | P:877.769.3765 | F: 877.875.7446 | E: [e-mail]

Easy Return/Easy Exchange
Want to return an item or exchange? Not satisfied with purchase?
No problem. We strongly believe in service after the sale and we stand behind our products
and our service to you, our valued customer. There is no problem we can’t solve for you!
Items that have been installed and/or damaged after receipt, are no longer in new and
ready-to-sell condition and cannot be refunded, replaced or exchanged unless it has a man-
ufacturer defect or was damaged in shipping. In addition, we cannot accept return on items
that are not in the original packaging. Items returned in poor condition or having parts
missing will not be credited.
Please note: Your request for return or replacement must be initiated within 30 days of
delivery of your merchandise.
Did your order arrive damaged?
Please do not install damaged products. Contact the company you purchased your product
from as soon as possible and notify them of the damages. They will make arrangements
with you to assist with the problem.
Did you order the wrong part or receive the wrong item?
Don’t worry. From time to time human error can result in problems with ordering or ship-
ping. Contact the company you purchased your product from as soon as you notice the
error. Every company has their own policy on returning parts that have been ordered incor-
rectly or shipped incorrectly.
In the event that you need to ship your part back to return/exchange, please ship to the
warehouse below:
CYC Returns Warehouse
2415 Cathy Lane
Jasper, IN 47546
Raptor Series Truck Accessories | P:877.769.3765 | F: 877.875.7446 | E: [e-mail]

For Powder Coated Steel Products
CYC Engineering, Inc. guarantees the original purchaser of our products
a limited ten (10) year warranty from the date of original purchase
against manufacturer defects in materials, workmanship and finish under
normal use. The step pads are covered under warranty for 1 year. This
warranty does not include damage resulting from road hazards such as
gravel or other debris, product misuse, improper installation, impair-
ments from accidents, product modifications, product neglect or
scratches during the life of the product. This limited ten year warranty
applies only to new products and is limited to the repair or replacement
of company’s products. Warranty does not include costs of removal,
installation, labor, inconvenience or consequential damages. Original
purchaser must return defective merchandise along with the purchase
receipt, to the original place of purchase.
For Stainless Steel Products
CYC Engineering, Inc. guarantees the original purchaser of our products
a limited lifetime warranty from the date of original purchase against
manufacturer defects in materials, workmanship and finish under normal
use. The step pads are covered under warranty for 1 year. This warranty
does not include damage resulting from road hazards such as gravel or
other debris, product misuse, improper installation, impairments from
accidents, product modifications, product neglect or scratches during
the life of the product. This limited lifetime warranty applies only to new
products and is limited to the repair or replacement of company’s prod-
ucts. Warranty does not include costs of removal, installation, labor,
inconvenience or consequential damages. Original purchaser must return
defective merchandise along with the purchase receipt, to the original
place of purchase.
LIMITED TEN (10) YEAR WARRANTY
LIMITED LIFETIME WARRANTY
Raptor Series Warranty

RTS64FD/RTS81FD
MAGNUM RT STEPS
Tools Required:
Torque Specifications:
For Rocker Panel Mount Installations
M8 through M12 bolts and nuts are set to 15-20 ft lbs.
1
13MM SOCKET
RATCHET TORQUE
WRENCH
Components: Hardware:
Rev 1
RTS64FD/RTS81FD
Driver Side
Step Bar
Qty 1
Passenger
Side Step Bar
Qty 1
Front Armor Plates
Qty 2
Mounting Brackets
Qty 6
M8 x 30 mm
Hex Head Bolts
Qty 18
M8 Hex Head
Nuts
Qty 12
M8 Flat
Washers
Qty 30
M8 Lock
Washers
Qty 24
M8 U-Nut
Clips
Qty 6
RTSPN175
Bolt/Nut Plates
Qty 6
M8 Plastic
Push Nuts
Qty 6

2
Rev 1
RTS64FD/RTS81FD
1. Remove all contents from the package and check steps for any damage. Also, verify that all
components and hardware listed above are included before you begin installation.
2. Remove the black tape and large rubber grommets over the mounting holes located on the inside face of
the rocker panel.
3. Existing mounting holes are located on the interior wall of the rocker panel. These mounting holes will be
used per the following instruction.
Begin by identifying the correct location for each of the M8 U-Nut Clips. See diagram for pinch weld and
rocker panel hole locations
Inside Rocker Locations for Ford Superduty
Looking at the pinch weld there are 10 holes long the length of the cab. The brackets will mount into the
2nd, 6th and 9th holes. Spacing between these holes is shown below.
Note: When installing the brackets and bars, all hardware must be left loose until all the items are attached.
35-7/8"
Vertical Underside
Holes in Pinch Weld
Horizontal Holes
Inside Rocker
Front
Bracket Mount
Front of
Vehicle
Front of
Vehicle
Middle
Bracket Mount
Rear
Bracket Mount
32-5/8"
Inside Rocker
Panel
2nd Hole6th Hole9th Hole

RTS64FD/RTS81FD
Rev 1
4. Install U Nut Clips so that the
threads are to the inside of the
rocker panel. Be careful not to drop
the U Nut Clips inside of the rocker
panel.
5. On the driver side of the vehicle,
align Mounting Brackets as shown.
3
Front
5
Driver Side
Installing the Brackets
6. Install each bracket to M8 U-Nut Clip using each bracket to the rocker panel using one (1) M8 Hex Head
Bolt, one (1) M8 Lock Washer and one (1) M8 Flat Washer per bracket (6a).
Attach lower portion of each bracket to the rocker panel using one (1) M8 Hex Head Bolt, one (1) M8 Lock
Washer, two (2) M8 Flat Washers and one (1) M8 Hex Head Nut.
6a 6b
Front
Front
M8
1x
1x
1x
M8
1x
2x
1x
1x
FRONT/REAR
BRACKET
ROCKER
PANEL
MOUNTING HOLE
U-NUT
INTERIOR WALL OF
ROCKER PANEL
4

RTS64FD/RTS81FD
Installing the Step Bar
7. Line up mounting points on
the step bar with the mounting
holes in each bracket.
8. Fasten the step bar to each
bracket using one (1) RTSPN175
Bolt/Nut Plate, one (1) Plastic
Push Nut, one (1) M8 Hex Head
Nut, two (2) M8 Lock Washers,
two (2) M8 Flat Washers and one
(1) M8 x 30MM Hex Head Bolt.
9. Adjust the bars front/back
and up/down to desired
placement. Once you have the
step positioned, tighten until the
split lock washer is flat between
the bolt head and flat washer. Do
not over tighten.
10. When all hardware is in
place, everything must be
tightened. See page 1 for torque
specifications. Repeat these
steps for opposite side
installation.
OPTIONAL:
If you wish to install the Front
Armor Plates, begin by
thoroughly cleaning the front
side of the front step where the
Front Armor Plate will attach.
1. Remove adhesive protection
from the Front Armor Plate.
2. Carefully line up with the front
side of the front step. Be careful
not to let the side overhang as
they could peel o over time.
Once lined up, firmly press the
Front Armor Plate on the step to
ensure complete adhesion.
Repeat these steps for opposite
side.
4
Driver Side
Rev 1
1
8
2
MOUNTING POINTS
ON INSIDE OF
STEP BAR
RTSPN175
BOLT/NUT PLATE
MOUNTING
BRACKET
M8 FLAT
WASHER
M8 LOCK
WASHER
M8 PLASTIC
PUSH NUT
M8 FLAT
WASHER
M8 LOCK
WASHER
M8 HEX
HEAD NUT
M8 x 30MM
HEX HEAD BOLT