Rayrun NT30 User manual

7
10
5
6
9
8
2
NT30 RGB LED controller is designed to drive constant
voltage LED products with common anode connection in
voltage range of DC12-24V. It can be controlled by smart
phone with Tuya smart app connection or by the stand
alone RF remote controller. user can setup RGB LED color,
brightness, scene and dynamic effects with the rich
function on smart phone Tuya app or the easy operation
RF remote controller.
1. Power supply input
Install positive power cable into the terminal marked
with ‘+’ and negative power cable into the terminal marked
with ‘-’. The controller can accept DC power from 12V to
24V, the output is PWM driving signal with same voltage
level as the power supply, so please make sure the LED
rated voltage is same as the power supply.
2. LED output
Connect LED fixtures to this terminal. Install LED
common anode cable into the terminal marked with ‘+’ and
each channel LED cables into the terminal marked with R,
G and B. Please make sure the LED rated voltage is same
as the power supply and each channel’s maximum load
current is below the controller rated current.
The controller will run into protection if the output
been overloaded or short circuited. The indicator will flash
red color and stop working in this case, Please check the
wiring and load current to remove the fault.
3. Work status indicator
This indicator shows all working status of the
controller. It displays different events as following:
Steady yellow: Remote only mode, Tuya disconnected.
Steady green: Remote and Tuya smart mode.
Single green blink: Command received.
Long single yellow blink: Brightness or speed reach
limit.
Red flash: Overload protection.
Yellow flash: Over heat protection.
Green flash 3 times: Setup command received.
5. Turn ON / OFF
Press ‘I’ key to turn on unit or press ‘O’ key to turn off.
The power on status can be set to last status or default
status from app. At last status mode, the controller will
memorize the on/off status and will restore to the
previous status on next power on. Please use remote
controller or app to turn on if it was switched to off status
before power cut.
87mm
24mm
72mm
1 2
3
Model: NT30 (W/Z/B)
IntroductionIntroduction
Dimension
Wiring & Indicator
Functions
Pair new
remote
Reset to
factory
Press in 10
seconds once
receiver powered
To 110/230
AC power
12-24V DC output
Power supply
NT30 LED
Controller
12-24V DC
LED Strips
LED Controller
12-24V Driving
4. Wiring diagram
2 3
11
Smart & Remote Control
RGB LED Controller
Full Protection High Power
Wireless Remote
Tuya Smart
Compact Size 12V/24V voltage

Model
NT30(W/Z/B)
Output Mode
PWM constant voltage
Working voltage
DC 12-24V
Rated output current
3x4A
Tuya connection
W: Wifi; Z: Zigbee; B: Bluetooth
Remote frequency
433.92MHz
Remote control distance
>15m at open area
PWM grade
4000 steps
Overload protection
Yes
Overheat protection
Yes
Controller dimension
87x24x15mm
Remote dimension
86.5x36x8mm
10. Remote indicator
11. Using the remote controller
Please pull out the battery insulate tape before using.
The RF wireless remote signal can pass through some
nonmetal barrier. For proper receiving remote signal,
please do not install the controller in closed metal parts.
This indicator blinks when remote controller is
working. If the indicator flash slowly when pressing keys, it
means the remote battery is nearly empty and please
change the remote battery (CR2032 type).
Operation
13. Pair a new remote controller
Specification
14. Reset to factory default
8. Brightness control
Press key to increase RGB LED brightness and
press key to decrease.
9. RGB dynamic effect
These keys control the RGB dynamic effects. Press
and to select dynamic effects and press and
key to set the running speed of the dynamic effects.
Press the key to activate the dynamic demo
mode, the controller will play dynamic effects in loop
with repeating for 3 times for each effect.
EFFECT
EFFECT
12. Setup Tuya connection
Please install the Tuya app to setup the smart
connection. Before setup, please make sure the controller
is at factory default mode and not connected to other
gateway or router. The controller indicator should be yellow
color at this status.
4 5
6
6/7. Static RGB color setting
The keys in this area set the RGB static color. Press the
colored keys to set the RGB LEDs to correspond color as
shortcut. Press and key to select color from the
preset library colors.
The remote controller and receiver is 1 to 1 paired as
factory default. It’s possible to pair maximum 5 remote
controllers to one receiver and each remote controller
could be paired to any receivers.
To pair a new remote controller, please follow two
steps:
1). Plug off the power of receiver and plug in again
after more than 5 seconds.
2). Press and key simultaneously for about 3
seconds, within 10 seconds after the receiver powered
on.
After this operation, the indicator will flash 3 times
to acknowledge that remote pairing is accomplished.
To reset the controller’s Tuya setting and unpair all
remote controllers, please operate with following two
steps:
1). Plug off the power of controller and plug in again
after more than 5 seconds.
2). Press and key simultaneously for about 3
seconds, within 10 seconds after the receiver powered
on.
After this operation, the indicator will flash yellow
color for 3 times and the controller will be reset to
factory default, the Tuya connection and remote pairing
will all be reset.
The controller has full protection function against
wrong wiring, load short circuit, overload and overheat.
The controller will stop working and the indicator will
flash with red / yellow color to indicate the malfunction.
The controller will try to recover from protection status
in a short time when the working condition is good.
For protection issues, please check the situation
with different indicator information:
Red flash: Check the output cables and load, make
sure no short circuit and the load current is in rated
range. Also the load must be constant voltage type.
Yellow flash: Check the installation environment,
make sure in a rated temperature range and with good
ventilation or heat dissipation condition.
Protection Function

7
10
5
6
9
8
2
NT30RGBLED控制器设计⽤于驱动电压范围为DC
12-24V的恒压LED产品。⽤⼾可以通过涂鸦智能app或
者卡⽚式射频遥控器来调节LED灯具。⽤⼾可以通过涂
鸦智能app的功能调节LED灯具的亮度、场景和动态模
式，也可以通过操作遥控器来调节LED灯具的亮度、颜
⾊和动态模式。
2.LED输出
连接到LED灯具。请将LED灯具正极连接到标有“+”
端⼦上，LED灯具对应颜⾊的电缆分别连接到标有
R、G、B 上，请确保LED的额定电压与电源相同，的端⼦
并且每个通道的最⼤负载电流在控制器的额定电流范
围内。
如果输出出现过载或短路的情况，控制器会⾃动进
⼊保护功能。此时指⽰灯会闪烁红⾊并停⽌⼯作，请及
时检查接线和负载电流以排除故障。
87mm
24mm
72mm
1 2
3
型号:NT30(W/Z/B)
简介
尺⼨
6/7.静态RGB颜⾊调节
1.电源输⼊
接线及指⽰灯
连接到电源。控制器可接受电压为12V到24V的直流
电源供电，请将电源正极连接到标有“+”电缆上，电源负
极连接到标有“-”电缆上。请确保LED灯具的额定电压
与电源电压相同，且电源的功率满⾜控制器和灯具的需
求。
为保证安全，在通电前请先确保所有电缆均已可靠
连接且绝缘良好。
3.⼯作状态指⽰灯
4.接线图解
功能
配对新遥控
恢复出⼚
设置
控制器
通电后
10秒内按下
2 3
11
涂鸦智能⽆线
RGBLED控制器
高功率
无线遥控
涂鸦智能
小尺寸 12-24V电压
全功能保护
该指⽰灯显⽰控制器的⼯作状态，指⽰灯与控制器
⼯作状态和对应关系如下：
⻩⾊常亮：遥控模式，涂鸦智能未连接。
绿⾊常亮：遥控和智能模式。
绿⾊单闪：收到命令。
⻩⾊慢闪：达到亮度或速度极限。
红⾊闪烁：过载保护。
⻩⾊闪烁：过热保护。
绿⾊闪烁3次：收到设置命令。
连交流电 12-24V
直流电源
NT30
LED控制器
12-24VDC
LED恒压灯具
5.开关
按“I”键开启灯光，按“O”键关闭。控制器会记忆断电
前的开关状态，如果在断电前为关机状态，下次通电后
请使⽤遥控器或者涂鸦智能app开灯。
这个区域的按键可以调节RGB静态颜⾊。按下颜⾊
快捷键可以将LED灯具调节为相应的颜⾊。按和
可以从预设的颜⾊库中调节颜⾊。
COLOR COLOR
控制器

型号
NT30(W/Z/B)
输出⽅式
PWM恒压
⼯作电压
DC12-24V
额定输出电流
3x4A
涂鸦连接
W:Wifi;Z:Zigbee;B:Bluetooth
遥控器⼯作频率
433.92MHz
遥控器⼯作距离
空旷范围>15⽶
PWM分辨率
4000级
过载保护
有
过热保护
有
控制器尺⼨
87x24x15mm
遥控器尺⼨
86.5x36x8mm
10.遥控器指⽰灯
11.使⽤遥控器
操作⽅法
规格
8.亮度调节
调节LED灯具亮度。按增加亮度，按降低亮度。
9.RGB动态效果
4 5
6
按和可以选择动态模式，按键和键
可以调节动态模式的运⾏速度。
按键激活动态演⽰模式，控制器将按每个动态
模式重复3次的⽅式循环演⽰动态效果。
MODE MODE
按下遥控器按键时，该指⽰灯会快速闪烁。如果指⽰
灯慢闪，则说明遥控器电池电量已耗尽，请更换遥控器
电池（CR2032型纽扣电池）。
使⽤前请拔出遥控器电池绝缘⽚。RF⽆线遥控信号
可以穿过⼀定的⾮⾦属屏障，为了保证控制器的接收效
果，请勿将控制器安装在有⼤⾯积⾦属遮挡的位置。
12.连接涂鸦智能app
请通过安装并设置涂鸦智能app来进⾏连接。在设
置连接前，请确保控制器是处于出⼚默认模式状态，且
没有连接任何⽹关或路由器。
按以下两个步骤操作，即可将涂鸦智能连接恢复到
出⼚状态，同时已配对的遥控器也会被清除。
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下遥控器的
和键约3秒钟。
操作完成后，控制器指⽰灯将闪烁3次⻩⾊表⽰已恢
复成出⼚状态，需要重新配置智能连接以及重新配对遥
控器。
13.与新遥控器配对
14.恢复出⼚设置
遥控器和控制器出⼚默认为1对1的配对状态。1个控
制器最多可配对5个遥控器，⽽遥控器可配对到任意的
控如需配对新遥控器，请按以下两个步骤操作：
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下新遥控器的
和键约3秒钟。
配对成功后，控制器指⽰灯将闪烁3次并提⽰配对成
功。
保护功能
本产品具有完善的保护功能，可以最⼤程度的防⽌
因接线错误、负载短路、过载或过热⽽引起的产品损
坏。当发⽣以上异常状态时控制器将停⽌⼯作，同时指
⽰灯会闪烁红⾊或⻩⾊。当⼯作状态良好时，控制器会
尝试恢复正常⼯作。
当控制器停⽌⼯作时，请检查指⽰灯的状态，在不
同的闪烁状态下应检查相应的故障：
红⾊闪烁：请检查输出电缆是否短路、负载电流是
否过⾼，并且请确保所驱动灯具为恒压驱动类型。
⻩⾊闪烁：请检查控制器的安装环境以及负载功
率，并确保控制器散热条件良好且负载功率在额定范
围之内。