Rayrun TT12 User manual

2
TT12 LED controller is designed to drive constant
voltage single color LED products in voltage range of
DC12-24V. It can be controlled by Tuya smart app or by a
handheld RF remote controller. User can setup LED
brightness with the rich function on the Tuya smart app or
from the easy operation remote controller.
Single Color LED Controller
Smart & Remote Control
High Power
RF Remote
Tuya Smart
Compact Size 12V/24V voltage
1. Power supply input
Connect positive power to the cable marked with ‘+’
and negative to the cable marked with ‘-’. The controller
can accept DC power from 12V to 24V, the output is PWM
driving signal with same voltage level as the power supply,
so please make sure the LED rated voltage is same as the
power supply.
2. LED output
Connect LED fixtures positive to the cable marked
with ‘+’ and negative to the cable marked with ‘-’.
Please make sure the LED rated voltage is same as the
power supply and the maximum load current is below
the controller rated current.
CAUTION! The controller will be permanently
damaged if output cables short circuited. Please ensure
the cables are well insulated to each other.
Introduction
11
Functions
2 3
To 110/230
AC power
12-24V DC output
Power supply
TT12 LED
Controller
12-24V DC
LED Strips
LED Controller
12-24V Driving
4. Wiring diagram
Overheat Protection
20.5mm
60mm
1 2
3
3. Work status indicator (optional)
This indicator shows all working status of the
controller. It displays different events as following:
Steady on: Remote and Tuya smart mode.
Flash twice: Tuya not connected.
Flash 3 times: Over heat protection.
Blink: New command received.
Long single blink: Reach brightness limit.
Model: TT12 (W/Z/B)
Terminal & Size
5
7
6
5. Turn ON / OFF
Press to turn on or off the output. The controller will
memorize the on/off status and will restore to the previous
status on the next power on. Please use remote controller to
turn on the unit if it was switched to off status before power
cut.
6. Brightness adjust
Press and key to adjust brightness sequentially.
Hold press these two keys will adjust the LED brightness
smoothly.

7. Remote indicator
8. Using the remote controller
Please pull out the battery insulate tape before using. The
RF wireless remote signal can pass through some nonmetal
barrier. For proper receiving remote signal, please do not install
the controller in closed metal parts.
Operation
11. Pair a new remote controller
Specification
12. Reset to factory default
To reset the controller’s Tuya setting and unpair all
remote controllers, please operate with following two steps:
1). Plug off the power of controller and plug in again
after more than 5 seconds.
2). Press and key simultaneously for about 3
seconds, within 10 seconds after the receiver powered on.
After this operation, the controller will be reset to
factory default, the Tuya configuration and remote pairing
will all be reset.
10. Setup Tuya connection
Please install the Tuya app to setup the connection. Before
setup, please make sure the controller is at factory default
mode and not connected to any gateway or router.
This indicator blinks when remote controller working.
Please check the remote battery if the indicator does not
light up or flash slowly. The battery type is CR2032.
4 5
6
The remote controller and receiver is 1 to 1 paired as
factory default. It’s possible to pair maximum 5 remote
controllers to one receiver and each remote controller could
be paired to any receivers.
To pair a new remote controller, please follow two steps:
1). Plug off the power of receiver and plug in again after
more than 5 seconds.
2). Press and key simultaneously for about 3
seconds, within 10 seconds after the receiver powered on.
After this operation, the LED fixture will flash quickly to
acknowledge that remote pairing is accomplished.
Overheat Protection
The controller has overheat protection feature and it can
protect itself from damage caused by some abnormal usage
such as overloading which generates excess heat. At
overheat situation, the controller will shutdown the output
for a short while and recover when temperature drops to a
safe range.
Please check the output current and make sure it’s
under rated level at this situation.
Model
TT12(W/Z/B)
Output Mode
PWM constant voltage
Working voltage
DC 12-24V
Rated output current
6A
Tuya connection
W: Wifi; Z: Zigbee; B: Bluetooth
PWM grade
4000 steps
Brightness grade
100 levels (App) / 10 levels (remote)
Overheat protection
Yes
Remote frequency
433.92MHz
Remote control distance
>15m at open area
Controller dimension
60x20.5x9mm

2
涂鸦智能⽆线
高功率
无线遥控
涂鸦智能
小尺寸 12-24V电压
1.电源输⼊
2.LED输出
简介
11
功能
2 3
接交流电 12-24V
直流电源
TT12
LED控制器
12-24V DC
LED恒压灯具
4.接线图解
过热保护
20.5mm
60mm
1 2
3
3.状态指⽰灯（ 可选）
型号:TT12(W/Z/B)
接线与尺⼨
5
7
6
5.开/关
6.亮度调节
单⾊LED控制器 TT12单⾊LED控制器是设计⽤于驱动电压范围
为DC12-24V的恒压LED产品。⽤⼾可以通过涂鸦智能
app或者⼿持式射频遥控器来调节LED灯具。⽤⼾可以
通过涂鸦智能app和遥控器来调节LED灯具的开关和亮
度。
连接到电源。控制器可接受电压为12V到24V的
直流电源供电，请将电源正极连接到标有“+”电缆
上，电源负极连接到标有“-”电缆上。请确保LED灯
具的额定电压与电源电压相同，且电源的功率满⾜控制
器和灯具的需求。
为保证安全，在通电前请先确保所有电缆均已可靠
连接且绝缘良好。
连接到LED灯具。LED灯具必须为恒压型且适⽤于
PWM驱动。请将LED灯具正极连接到标有“+”电缆上，
LED灯具负极连接到标有“-”电缆上，请确保LED的额
定电压与电源相同，并且最⼤负载电流在控制器的额定
电流范围内。
请注意！如果控制器输出电缆被意外短路，可能将导
致控制器严重损坏，请确保电缆可靠连接并良好绝缘。
该指⽰灯显⽰控制器的⼯作状态，指⽰灯与控制器
⼯作状态和对应关系如下：
常亮：遥控和智能模式
快闪2次：遥控模式，涂鸦智能未连接
快闪3次：过热保护
闪烁：收到命令
慢闪：达到亮度极限 此按键可开启或关闭灯光。控制器会记忆断电前的
开关状态，如果断电前为关闭状态，下次通电后请使⽤
遥控器开启。
按键增加亮度，按键降低亮度。⻓按亮度调
节键时亮度会连续平滑变化。
控制器

7.遥控器指⽰灯
8.使⽤遥控器
使⽤前请拔出遥控器电池绝缘⽚。RF⽆线遥控信号
可以穿过⼀定的⾮⾦属屏障，为了保证控制器的接收效
果，请勿将控制器安装在有⼤⾯积⾦属遮挡的位置。
操作⽅法
10. 与新遥控器配对
规格
12.恢复出⼚设置
9.连接涂鸦智能app
按下遥控器按键时，该指⽰灯会快速闪烁。如果指⽰
灯慢闪，则说明遥控器电池电量已耗尽，请更换遥控器
电池（CR2032型纽扣电池）。
4 5
6
过热保护
本机具有过热保护功能，可防⽌控制器因负载过
重引起异常发热⽽导致损坏。过热保护时控制器将关
断输出，当温度下降到安全范围时，将尝试恢复正常
⼯作。过热保护功能仅能在⼀定程度上防⽌控制器损
坏，为确保安全，请勿将控制器输出过载或短路。
请通过安装并设置涂鸦智能app来进⾏连接。在设
置连接前，请确保控制器是处于出⼚默认模式状态，且
没有连接任何⽹关或路由器。
遥控器和控制器出⼚默认为1对1的配对状态。1个控
制器最多可配对5个遥控器，⽽遥控器可配对到任意的
控制器。
如需配对新遥控器，请按以下两个步骤操作：
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下新遥控器的
和键约3秒钟
配对成功后，LED灯具将快速闪烁提⽰配对成功。
按以下两个步骤操作，即可将涂鸦智能连接恢复到
出⼚状态，同时已配对的遥控器也会被清除。
1）断开控制器电源，并在超过5秒后重新通电。
2）在控制器通电后的10秒内，同时按下遥控器的
和键约3秒钟。
操作完成后，控制器将恢复成出⼚状态，需要重新
配置智能连接以及重新配对遥控器。
型号
TT12(W/Z/B)
输出⽅式
PWM恒压
⼯作电压
DC12-24V
额定输出电流
6A
涂鸦连接
W:Wifi;Z:Zigbee;B:Bluetooth
遥控器⼯作频率
433.92MHz
遥控器⼯作距离
空旷范围>15⽶
PWM分辨率
4000级
亮度可调级数
100级（ App）/7级（遥控器）
过热保护
有
控制器尺⼨
60x20.5x9mm