rba RBA4801-Straight Series Manual

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
SYDNEY | MELBOURNE | BRISBANE | PERTH | AUCKLAND
Australia 1300 788 778 www.rba.com.au | New Zealand 0800 722 111 www.rbagroup.co.nz1 of 4
As improvements in the design and performance of RBA products are continuous, specications may be subject to change without notice.
The illustrations and descriptions herein are applicable to production as of the date of this Installation Instructions Sheet. Revised 03/23 © 2023 by RBA Group II/Model RBAModularRails/0323
RBA4801-Straight-Series Straight Modular Grab Rail
RBA4801-450 Ambulant Modular Grab Rail | 450mm x 450mm
RBA4801-901 Accessible 90° LH Modular Grab Rail | 950mm x 700mm
RBA4801-911 Accessible 90° RH Modular Grab Rail | 950mm x 700mm
MODELS RBA MODULAR RAILS
*RBA4801-901 Shown
Sourced/ Supplied under QMS

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
SYDNEY | MELBOURNE | BRISBANE | PERTH | AUCKLAND
Australia 1300 788 778 www.rba.com.au | New Zealand 0800 722 111 www.rbagroup.co.nz2 of 4
• 1x Straight rail [for RBA4801-straight-series]
• 1x Ambulant rail [for RBA4801-450]
• 2x Flange cover
• 2x Wall plate
• 2x Bolts
• 8x Screws
• 8x Wall plugs
Attention
You are responsible for the safe operation of this unit. For optimum installation use at least 4 suitable screws for each wall
plate. Screws should be selected to suit the wall type. Grab rails are no stronger than the anchors or walls to which they are
attached, and therefore must be rmly secured in order to support the loads for which they are intended.
Exceeding the maximum load values may cause permanent product damage. If this happens, cease use until checked by
a specialised maintenance person. Improper use, such as for gymnastic exercises or as a step, may cause accidents with
serious consequences. Reliable operation and product safety depend on the way the products are installed and used.
Ensure installation is performed by qualied personnel. Incorrect installation can seriously compromise product functionality.
Maintenance and Cleaning Instructions
Do not use detergents containing bleach, acids, alkalis, chlorine or abrasive products. Do not use abrasive objects [e.g.
scouring pads]. Do not use chemicals that can damage plastic. Clean the surface with water and a neutral detergent; rinse
carefully and dry with a clean cloth. If alternative cleaning methods and/or chemicals are used, warranty may become void.
• Screw Driver
Components Supplied for RBA4801-901 & RBA4801-911
• Extended Driver Bit • Spirit Level
Components Supplied for RBA4801-Straight-Series & RBA4801-450
Tools Required
• 1x Long straight rail [open-ended]
• 1x Short straight rail [open-ended]
• 1x LH connector rail [for RBA4801-901]
• 1x RH connector rail [for RBA4801-911]
• 2x Dress rings
• 3x Flange cover
• 3x Wall plate
• 3x Bolts
• 12x Screws
• 12x Wall plugs

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
SYDNEY | MELBOURNE | BRISBANE | PERTH | AUCKLAND
Australia 1300 788 778 www.rba.com.au | New Zealand 0800 722 111 www.rbagroup.co.nz3 of 4
1. Lay rail at with thread facing up. 2. Slide ange cover over post. 3. Insert bolt through wall plate.
4. Insert wall plate and bolt assembly. 5. Tighten.
8. Slide ange covers down into place.
Installing RBA4801-Straight-Series & RBA4801-450
7. Ensuring rail is level, slide up ange
cover and secure screws. Repeat for
all xing points.
6. Repeat for other xing points.

INSTALLATION, OPERATION AND MAINTENANCE INSTRUCTIONS
SYDNEY | MELBOURNE | BRISBANE | PERTH | AUCKLAND
Australia 1300 788 778 www.rba.com.au | New Zealand 0800 722 111 www.rbagroup.co.nz4 of 4
12. Ensuring rail is level, slide up
ange cover and secure screws.
Repeat for all xing points.
10. Slide dress rings over connector
piece on both sides.
9. Follow Steps 1-6 to secure wall
plate to rail, repeating for all xing
points.
13. Slide ange covers down into
place.
11. Slide both straight rails into place
over connector piece. Please note the
xing on the connector piece is always
parallel to the vertical straight rail.
Installing RBA4801-901 & RBA4801-911