RCA VR705HF User manual

VCR
User’s Guide
Changing Entertainment. Again.
VR705HF

This symbol indicates
"dangerous voltage" inside the
product that presents a risk of
electric shock or personal injury.
WARNING
To reduce the risk of fire or
electric shock, do not expose
this product to rain or moisture.
To reduce the risk of electric shock, do not
remove cover (or back). No user serviceable
parts inside. Refer servicing to qualified
service personnel.
This symbol indicates
important instructions
accompanying the
product.
CAUTION
RISK OF ELECTRIC
SHOCK. DO NOT OPEN.
Caution: To prevent electric shock, match
wide blade of plug to wide slot, fully insert.
Attention: Pour éviter les chocs électriques,
introduire la lame la plus large de la fiche
dans la borne correspondante de la prise et
pousser jusqú au fond.
Refer to the identification/rating label located
on the back panel of your product for its
proper operating voltage.
FCC Regulations state that unauthorized changes or modifications to
this equipment may void the user’s authority to operate it.
Cable TV Installer: This reminder is provided to call your attention to
Article 820-40 of the National Electrical Code (Section 54 of the
Canadian Electrical Code, Part 1) which provides guidelines for proper
grounding
and, in particular, specifies that the cable ground shall be connected to
the grounding system of the building as close to the point of cable
entry as practical.
Product Registration
Please fill out the product registration card and return it immediately. Returning the card allows us to
contact you if needed.
Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here
and record the serial and model numbers in case you need them. The numbers are located on the back
of the VCR.
Model No._______________________________________________________________________________________
Serial No. _______________________________________________________________________________________
Purchase Date:___________________________________________________________________________________
Dealer/Address/Phone: ___________________________________________________________________________
Important Information
VR705HF
i

1
Introduction
Introduction
Key Features Overview
Your VCR is equipped with features that will add to your recording and viewing experience. The
following information summarizes a few of these features. Chapter 4 provides more information
about the rest of the VCR’s features and how to use them.
I
N
P
U
T
T
V
•
V
C
R
PLAY FORWARD
RECORD STOP PAUSE
F.ADV
CLEAR MENU SPEED
TRACKING
1
4
7
2
5
8
3
6
9
0
C
H
A
N
V
O
L
V
O
L
C
H
A
N
INFO SEARCH
MUTE GO BACK
VCR
ON•OFF
TV
REVERSE
Rec Ch 36
Record Length 1:30
Press REC to set length
TIMER RECORDINGS
1>Create a New Program
2 Review Existing Progs.
0 Exit
Universal Remote Control
Description: The VCR’s remote control can operate most RCA, GE, and Proscan
TVs with no additional steps and can control many other remote-controllable
devices with just a few programming steps.
Requirements: Point the remote control at the active device to see if it can be
operated. If necessary, program the remote control following the steps listed in
this manual’s “Working with the Remote Control” chapter.
Express Recording (XPR)
Description: XPR quickly records the remaining portion of a program already
in progress. XPR is a great way to capture the end of a sporting event that has
run into overtime or a live broadcast that runs long.
Requirements: Repeatedly press the Record button on the remote control or
the VCR front panel to add 30-minute increments of time to record.
Timer Recordings
Description: Your VCR allows you to program up to eight different future
broadcasts to be recorded. You can catch a one-time, daily, or weekly broadcast
to record.
Requirements: The VCR’s clock must be set correctly. A tape with its safety tab
in place and enough tape to record a program must be inserted into the VCR.
For a cable box or satellite receiver, turn it on and tune it to the channel you
want to record before the recording is to begin.
Commercial Scan
Description: The purpose of Commercial Scan is to assist you in searching
forward on a tape through a block of commercials.
Requirements: A Commercial Scan is performed in 30-second units. Each
press of the remote control’s SEARCH button adds an additional 30-seconds, up
to a maximum of 5 minutes (10 total presses of the SEARCH button). If you
press the SEARCH button and the timer is within the 4:30-5:00 range, then the
timer will be set to 5:00.

2
Introduction
ShowSaver™ Memory Protection
Description: Set timer programs are stored indefinitely using the VCR’s
permanent memory so you’ll never have to worry about losing your programs
due to an extended power outage.
Requirements: Store a daily or weekly timer program in the VCR’s memory.
Pro-Tect Plus™ Locking
Description: Protects preprogrammed VCRs from frustrating recording accidents
or interruptions from children.
Requirements: Set the VCR to Lock by pressing and holding the POWER button
on the remote control for six seconds. “SAFE” will appear on the VCR front
panel. The VCR unlocks by pressing and holding the POWER button on the
remote control, again for six seconds.
Front Audio/Video Input Jacks
Description: The VCR has Audio/Video (A/V) input jacks on both the front and
rear of the unit (there are output jacks on the rear panel only). The front A/V
jacks make it easy to plug in an external A/V device, such as a camcorder.
Requirements: Make sure that all A/V connections are snug. To see a
connected device’s image, turn the VCR to its Video Line Input by pressing the
remote control’s INPUT button.
Hi-Fi Quality Sound
Description: When using the VCR’s A/V jacks, you can feed stereo quality
sound from your VCR to your TV or stereo. Stereo quality sound allows for two
separate channels of sound (Left and Right) to be heard.
Requirements: Using A/V jacks and cables to connect the VCR to the TV or
stereo.
TIMER
VIDEO
INPUT LEFT RIGHT
AUDIO

3
Table of Contents
Product Registration ............................................................................................................. i
Introduction ............................................................................................................................ 1
Key Features Overview ......................................................................................................... 1
Connections & Setup ........................................................................................................... 5
Things to Consider Before Connecting Components .......................................................... 6
Cable Considerations ............................................................................................................6
Choose Your Connection ...................................................................................................... 7
Using the RF Coaxial Cable to Connect the VCR to a TV .............................................. 7
TV + VCR .......................................................................................................................... 8
TV + VCR + Satellite Receiver ......................................................................................... 9
TV + VCR + Cable Box ................................................................................................... 10
Set the VCR’s CH 3/4 Switch ................................................................................................ 11
Plug in the VCR .................................................................................................................... 11
Put Batteries in the Remote Control .................................................................................. 11
Turn on the TV and VCR ...................................................................................................... 11
Tune the TV .......................................................................................................................... 11
Using the Remote Control to Navigate On-Screen Menus ............................................... 12
Complete the QuickSet Guide ...................................................................................... 12
Accessing Menus ........................................................................................................... 12
VCR Basics ............................................................................................................................ 13
Playing a Tape ............................................................................................................... 13
Automatic Rewind ........................................................................................................ 13
Tape Eject ......................................................................................................................13
Recording ............................................................................................................................. 13
Check the Safety Tab .................................................................................................... 13
Using the VCR’s Menu System ....................................................................................... 15
Using On-Screen Menus to Set Up Features ...................................................................... 16
Language ....................................................................................................................... 16
Cable Box Setup ............................................................................................................ 16
VCR Channels List.......................................................................................................... 17
Auto Channel Searching ....................................................................................... 17
Changing the Signal Type ..................................................................................... 18
Adding or Removing Channels ............................................................................. 18
Time and Date ............................................................................................................... 19
Auto Clock Set Feature.......................................................................................... 19
To Turn Auto Clock Set ON .............................................................................. 19
Setting the Time Zone ..................................................................................... 20
Setting Daylight-Saving Time .......................................................................... 20
Setting Time and Date Manually .......................................................................... 20
Additional Set Up Features in the Preferences Menu ....................................................... 21
Remote VCR1/VCR2 Option .......................................................................................... 21
Auto Play .......................................................................................................................21
Auto TV/VCR .................................................................................................................. 22
EnergySaver................................................................................................................... 22
Front Panel Brightness (VCR Display) .......................................................................... 22
Tape Speed .................................................................................................................... 23
Set Auto Repeat ............................................................................................................ 23

Table of Contents
4
Using the Remote Control ............................................................................................... 25
Using the Remote Control .................................................................................................. 26
Buttons of the Remote Control ................................................................................... 26
Using the INPUT Button ........................................................................................ 27
Operating a TV with the VCR’s Remote Control ............................................................... 28
Do You Need to Program the Remote? ....................................................................... 28
Programming the Remote Control ....................................................................... 28
Operating the TV ................................................................................................... 28
Using the VCR’s Features .................................................................................................. 31
Recording Features ............................................................................................................. 32
Express Recording (XPR) ............................................................................................... 32
Timer Recording ............................................................................................................ 33
Stopping a Timer Recording ................................................................................. 33
Reviewing and Clearing Programs ....................................................................... 34
Recording Broadcast Stereo TV or SAP (Second Audio Program) .............................. 34
Copying and Editing Tapes Using Two VCRs ............................................................... 35
Picture Search Options ........................................................................................................ 36
Forward and Reverse Search ........................................................................................ 36
Slow Motion .................................................................................................................. 36
Frame Advance ............................................................................................................. 36
Index Search .................................................................................................................. 37
Zero Search .................................................................................................................... 37
Pro-Tect Plus™Locking Feature ......................................................................................... 38
Tracking ................................................................................................................................ 38
Time Counter ....................................................................................................................... 38
On-Screen Displays ..............................................................................................................39
Audio Set-Up Features ........................................................................................................ 40
Reception ...................................................................................................................... 40
Tape Playback ...................................................................................................................... 40
Other Information .............................................................................................................. 41
Troubleshooting Tips ........................................................................................................... 42
General VCR Problems .................................................................................................. 42
Recording Problems ...................................................................................................... 43
Playback Problems ........................................................................................................ 43
Front Panel .......................................................................................................................... 45
Display Panel ....................................................................................................................... 46
Back Panel ............................................................................................................................ 47
RCA VCR Limited Warranty................................................................................................. 48
Specifications ....................................................................................................................... 49
Cleaning the VCR ................................................................................................................49
How to Find Your TV’s Video Input Channel ..................................................................... 50
Advanced Connection ......................................................................................................... 51
TV + VCR + Satellite Receiver ....................................................................................... 51

5
Changing Entertainment. Again.
Connections &
Setup
Chapter Overview:
•Things to Consider Before Connecting
•Choosing Your Connection
•Making Connections
•Why You Should Connect with Audio/Video Jacks
•Navigating On-Screen Menus
•Completing the QuickSet™Guide
•Basic Recording
Chapter 1

6Chapter 1
Connections & Setup
Things to Consider Before Connecting
Components
Protect Components From Power Surges
• Connect all components before plugging any power cords into the wall outlet.
• Always turn off the TV and other components before you connect or disconnect any cables.
Position Cables to Avoid Audio Hum or Interference
• Insert all cable plugs firmly into their jacks.
• Place any Audio/Video (A/V) cables to the side(s) of the TV’s back panel instead of straight
down the back after connecting components.
• Try not to coil any twin-lead cables and keep them away from all A/V cables as much as
possible.
• Make sure all antennas and cables are properly grounded. Refer to the Safety Tips sheet
packed with your unit for detailed information.
Protect Components From Overheating
• Never block ventilation slots in any component. Arrange the components so that air can
circulate freely.
• Do not stack components.
• Allow adequate ventilation when placing components in a stand.
• Place an amplifier or satellite receiver on the top shelf of a stand so heated air rising from it
will not flow around other components.
Cable Considerations
The RF coaxial cable supplied with your VCR carries both sound and picture information. This is
the cable used in all connection diagrams illustrated in this chapter.
If your TV has A/V input jacks, you should use A/V cables (not supplied) to connect the VCR to
the TV. A/V cables provide better picture and sound quality than an RF coaxial cable. If you
would like to hook up your VCR using A/V cables, refer to the Advanced Connection
information on page 51 in the Other Information chapter of the manual.

Chapter 1 7
Connections & Setup
Components Connection Go To
Title
TV + VCR page 8
TV + VCR +
Satellite page 9
Receiver
TV + VCR +
Cable Box page 10
VCR
TV
Satellite
CableBox
VCR
TV
VCR
TV
RF Coaxial Cable
Using the RF Coaxial Cable to Connect the
VCR to a TV
This graphic shows the RF coaxial cable supplied with your VCR. This will be
the cable used for the basic connections represented in this chapter.
Notes: To hear stereo sound, you will need to purchase Audio/Video (A/V)
cables (not provided) and connect the VCR to the TV. A/V jacks and cables
also provide a superior image and sound quality. For details about using
this advanced setup, see the instructions on page 51.
Using A/V jacks to connect the VCR to the TV requires tuning to the TV’s
Video Line Input to see the VCR’s picture. For more information about
finding your TV’s Video Line Input, see page 50.
If you prefer, we can provide you with the name of an Authorized Service
Representative who will visit your home for a fee to install your electronic
entertainment system and to instruct you in its operation. For details about
this service, call 1-888-206-3359.
Choose Your Connection
There are several ways to hook up your VCR depending on the components
connected. Please use the following chart to determine which connection is
best for you and proceed to the appropriate page.

8Chapter 1
Connections & Setup
TV + VCR
Note: Your television back panel may not look exactly like the
model shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT
jack on the back of the VCR and the other end to the TV’s Antenna
IN jack.
2. Connect the antenna/cable feed to the VCR
Connect the cable or antenna RF coaxial cable to the ANT. IN jack on
your VCR.
Note: Flip the CH 3/4 switch on the back of the VCR to the channel
that is not used in your area. This will be the channel that the TV
must be tuned to in order to see the VCR’s picture.
Go To Page 11
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
VCR
TV
VCR
TV (back panel)
CABLE/
ANTENNA
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
From Cable
or Antenna
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
2
1

Chapter 1 9
Connections & Setup
TV + VCR + Satellite Receiver
Note: Your television and/or satellite receiver back panels may not
look exactly like the models shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT jack
on the back of the VCR and the other end to the TV’s Antenna IN jack.
2. Connect satellite receiver to the VCR
Connect an RF coaxial cable to the RF OUT jack on the cable box and
to the CABLE/ANTENNA input jack on the TV.
3. Connect the antenna to your satellite receiver
If necessary, connect an antenna or cable box RF coaxial cable (not
included) to the antenna input jack on the satellite receiver.
4. Connect the satellite feed to the satellite receiver
Connect the satellite receiver’s RF coaxial cable feed (not included) to
the satellite input jack on the satellite receiver.
Go To Page 11
VCR
TV
Satellite
CABLE/
ANTENNA
VCR
TV
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
CH3
CH4
S-VIDEO
L
R
VIDEO
OUT
IN FROM ANT
OUT TO TV SATELLITE
IN
From
Satellite
From Cable
or TV Antenna
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
SATELLITE
RECEIVER
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
3
1
2
4

10 Chapter 1
Connections & Setup
TV + VCR + Cable Box
Note: Your television and/or cable box back panels may not look exactly
like the models shown here.
1. Connect the VCR to the TV
Connect one end of the supplied RF coaxial cable to the RF OUT jack on
the back of the VCR and the other end to the TV’s Antenna IN jack.
2. Connect the cable box to the VCR
Connect one end of a second RF coaxial cable (not included) to the
cable box’s TV output jack and the other end to the antenna input jack
on the TV.
3. Connect the cable feed to your cable box
Connect the RF coaxial cable feed (not included) to the antenna input
jack on the cable box.
Go To Page 11
CABLE/
ANTENNA
VCR
TV
VIDEO RL / MONO
S-VIDEO
AUDIO
L
IN
OUT
CH3
CH4
CABLE BOX
S-VIDEO
IN FROM ANT
OUT TO TV
From Cable
Feed
ANT. IN
RF OUT
CH.
VIDEO
AUDIO
OUT IN
R
L
3 4
Need Some Help?
If you prefer, we can
provide you with the
name of an Authorized
Service Representative
who will visit your home
for a fee to install your
electronic entertainment
system and to instruct you
in its operation. For
details about this service,
call 1-888-206-3359.
VCR
TV
CableBox
1
2
3

Chapter 1 11
Connections & Setup
Set the VCR’s CH 3/4 Switch
The CH 3/4 switch on back of the VCR determines what channel the TV must be tuned to see
the VCR’s image. Choose whichever channel is not used locally in your area.
Note: If you connected components using A/V jacks and cables, the VCR’s signal must be
viewed using the TV’s Video Line Input. To find the Video Line Input, refer to the manual
that came with the TV or see How to Find Your TV’s Video Line Input on page 50 in the
Other Information section of this manual.
Plug in the VCR
Your VCR’s power cord has a plastic band strung through the blades. Remove the plastic band
before plugging the cord into the power outlet. To remove the band, cut with a pair of
scissors and pull it free of the blades. Once the plastic is removed, match the wide blade of the
power cord to the wide slot in the AC outlet. Be sure to insert the plug completely.
Put Batteries in the Remote Control
1. Remove the battery compartment cover on the remote control.
2. Insert new batteries matching the polarities (+ and –) on the batteries with
the diagram in the battery compartment.
3. Put the battery compartment cover back on the remote.
Turn on the TV and VCR
Turn on the TV and press the VCR button on the remote control to turn it on.
Note: If you have an RCA, GE, or Proscan TV, your VCR’s remote control
may be able to operate it without being programmed. Press the TV button
on the remote control and then the ON•OFF button. If neither one turns on
the TV, see Using the Remote Control starting on page 25 for details about
programming the remote control to operate other brands of TVs.
Tune the TV
Tune the TV to the VCR viewing channel. The VCR viewing channel is channel
3, 4, or the TV’s video line input.
• If you connect your VCR using RF coaxial cable only, turn the TV to
channel 3 or 4 (whichever was set on the CH 3/4 switch).
• If you connected the VCR using A/V jacks and cables, select the TV’s video
line input. For more information see How to Find the TV’s Video Line Input
on page 50 in the Other Information section of this manual.

12 Chapter 1
Connections & Setup
Using the Remote Control to
Navigate On-Screen Menus
The technical term is “Navigation” – how you move through the on-screen menus. The theory is
the same for all the menu screens; use the corresponding number button on the remote control
select it.
To choose an on-screen item, press the remote control’s corresponding number button.
Note: Selecting a menu item can take you to another menu, activate a choice, or activate a
data entry field (such as the hour field in the Set Time menu).
Select a language.
Seleccione un idioma.
Choisissez une langue.
1 English
2 Español
3 Français
VCR MAIN MENU
1 Timer Recordings
2 Time
3 Channels
4 Setup
5 Preferences
6 Audio
7 Language
0 Exit
Complete the QuickSet Guide
The menu system in your VCR allows you to customize your preferences as
well as use all the VCR’s features. To help you use the VCR as quickly as
possible, there is an initial QuickSet Guide that walks you through several
important setup steps at one time.
The first time you turn on the VCR, you will be able to set up available
channels, time and date information, and more. The first menu you will see
asks which language you prefer to have the on-screen menus appear in.
Note: With numbered menu choices, press the corresponding number
button on the remote control to automatically select it. In the case of the
language menu, press 1 for English, 2 for Español (Spanish), or 3 for
Français (French).
The remaining menus throughout the setup will appear in the language chosen.
Just follow the step-by-step procedures until the QuickSet Guide is complete.
Accessing Menus
The series of preferences that are set in the QuickSet Guide can also be
handled individually using the VCR’s on-screen menu system. There are other
settings not covered in the initial setup that are also handled using the on-
screen menus.
For example, if you decide to run the QuickSet Guide again, you can access the
Setup menu by pressing the remote control’s MENU button. Once the Main
Menu is displayed, press the 5 button to choose Setup. From there, you can start
the QuickSet Guide from the beginning.
All on-screen menus are accessed the same way, starting in the Main Menu
which is displayed by pressing the remote control’s MENU button.
Note: See chapter two, Using On-Screen Menus, for details about changing
the VCR’s individual settings.
All of the VCR’s menus are accessed
through the Main Menu. Press the
remote control’s MENU button to
start.

Chapter 1 13
Connections & Setup
VCR Basics
Once your initial settings are complete, you can begin using your VCR. In order to begin, you
must first understand some basic concepts.
POWER
TAPE SPEED
INPUT
TV•VCR
VIDEO
INPUT LEFTMONO RIGHT
VIDEO
P
L
A
Y
P
A
U
S
E
REV FWD
STOP•EJECT RECORD
CHANNEL
TRACKING
Safety Tab
Automatic Tracking
The VCR has automatic tracking
which adjusts the picture when
playing back a tape recorded on
another VCR. To adjust tracking
manually, use the TRACKING -/+
buttons on the remote control.
Playing a Tape
1. Tune the TV to your VCR viewing channel (03, 04, or the video line input).
2. Insert a tape in the VCR.
If the Auto Play feature is set to ON, the tape automatically begins playback
(if the safety tab on the tape is removed).
• Press FWD or REV (FORWARD or REVERSE on the remote control) to
cue the tape at the desired starting position.
• Press PLAY (if necessary) to begin tape play.
• Press PAUSE for stop action.
• Press TRACKING up or down (TRACKING + or – on the remote
control) to remove any streaks from the picture, if necessary.
• Press STOP to stop playback.
Automatic Rewind
The VCR automatically rewinds the tape if it reaches the end of the tape during
playback. While rewinding, you can press the ON•OFF button and the VCR will
turn off after finishing. If the tape has no safety tab, it will be ejected.
Tape Eject
Press the EJECT button on the VCR when stopped to eject the tape. You can
also press and hold the remote control’s STOP button for three seconds.
Recording
To Capture Programming with Basic Recording Methods:
1. Set the tape speed by pressing the SPEED button on the remote control
(see Tape Speed on page 23 for information about recording speeds).
2. Press the RECORD button to begin recording.
3. Press the STOP button to halt recording.
If you just want to pause the recording for a short time (like during a
commercial), press PAUSE instead of STOP.
Check the Safety Tab
No matter which recording option you use, make sure there is a tape in the
VCR with its safety tab in place. You cannot record on a tape with its safety tab
removed. If the safety tab is removed and you want to record, simply cover the
hole with adhesive tape.

This page left blank intentionally

15
Changing Entertainment. Again.
Using the VCR’s
Menu System
Chapter Overview:
•Setting Up the VCR’s Preferences
•Using On-Screen Menus
•Cable Box Setup
•Setting Time and Date
•Setting VCR Preferences
Chapter 2

16 Chapter 2
Using On-Screen Menus
Using On-Screen Menus to Set Up Features
You set up many of the VCR’s features by using the menu system as discussed in the previous
chapter. Each feature that appears in the QuickSet Guide is explained in this section as well as a
few other features you should set up to get the most out of your VCR.
Note: Not all the VCR screens are shown in this manual when explaining how to access
features.
Language
Selecting your preferred language determines how the on-screen displays will
appear. To change the language:
1. Press MENU to display the VCR MAIN MENU.
2. Press the 7 button to select LANGUAGE.
3. Select English, Spanish (Español), or French (Français).
Cable Box Setup
This setup applies only when all channels are received through a cable box. In
this case, the VCR will automatically enter the channel used to view cable box
programming. Your VCR will use this channel for all future timer recordings.
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to display the CHANNELS menu.
3. Press 4 to display the CABLE BOX SETUP menu.
4. Select one of the three choices.
LANGUAGE
Select a language.
1>English
2 Español
3 Français
Press MENU to continue
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 Cable Box Setup
0 Exit
CABLE BOX SETUP
Do you use your cable
box to receive ALL
channels or only SOME
channels?
1 ALL channels
2 Only SOME channels
3 Cancel setup

Chapter 2 17
Using On-Screen Menus
If “ALL Channels” is selected, enter the output channel of the cable box
(usually 03 or 04), or if A/V jacks connect the VCR to the TV, press the
INPUT button on the VCR’s remote control.
5. Once you complete the setup, the VCR confirms that it will now receive all
signals on the designated channel.
VCR Channels List
Your VCR may come with a list of channels preset at the factory. Even though it
may come with such a list, you might want to add or delete certain channels.
Note: If you use a cable box to view all channels, this step is not necessary.
Auto Channel Searching
Notes: Use Auto Channel Search to place all available channels in memory.
If you ever change cable or antenna signals, you may need to run the Auto
Channel Search feature again.
1. Press the MENU button to display the VCR MAIN MENU.
2. Press 3 to select CHANNELS.
3. Press 1 to select AUTO CHANNEL SEARCH.
4. Select one of the three options:
Cable TV searches for cable stations.
Antenna searches for local broadcast stations.
Detect Automatically decides which input to use for you.
Note: With Detect Automatically, a strong cable or antenna signal in your
area may cause channels to be detected inaccurately. If this should happen,
manually select the input signal for the system you have.
The VCR begins scanning for channels available in the area (taking about
one-to-two minutes). When scanning is complete, the VCR tunes to the
lowest channel available. After completing Auto Channel Search, pressing
the remote control’s CHAN + or - buttons should only select active
channels.
CABLE BOX SETUP
On what channel does
the VCR receive signals
from the cable box?
(usually 3, 4, or Video)
--
Enter 01-13 or INPUT
Press MENU to cancel
CABLE BOX SETUP
The VCR will now
receive all signals
from the cable box
on channel 04.
Press MENU to continue
AUTO CHANNEL SEARCH
What type of signal
are you using?
1 Cable TV
2 Antenna
3>Detect Automatically
0 Cancel

18 Chapter 2
Using On-Screen Menus
Changing the Signal Type
This feature is useful if your cable signal goes out; it allows you to switch to a regular antenna
for alternate television reception.
CHANNELS
1 Auto Channel Search
2 Add/Remove Channels
3 Signal Type: CABLE
4 Cable Box Setup
0 Exit
ADD/REMOVE CHANNELS
Channel 115
is presently ADDED
Press CLEAR to remove
Press MENU to exit
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to choose CHANNELS.
3. Press 3 repeatedly to change the Signal Type between Cable and Antenna.
When you are finished, press 0 to exit back to the VCR MAIN MENU and
press 0 again to exit to normal viewing.
Adding or Removing Channels
You may want to add or remove channels after using Auto Channel Search,
especially if there are weak signals or channels with content you don’t care for.
1. Press MENU to display the VCR MAIN MENU.
2. Press 3 to display the CHANNELS menu
3. Press 2 to choose ADD/REMOVE CHANNELS. To go to the channel you want
to add or remove, use the remote control’s CHANNEL + or – buttons or
enter a specific channel number using the number buttons.
Once the desired channel is displayed, the on-screen menu will tell you if
the current channel is in your viewing list. Press CLEAR to remove a channel
from the available channels list or press INFO to add it.
4. Once you are finished adding/deleting channels, press MENU to exit out of
the menus.
NOTE: To view active channels, use the remote control’s CHANNEL + and -
buttons. You can also access channels not available in the active channel list
by using the remote control’s number buttons to enter the specific channel
number.