Recordex TriMaxx User manual

TriMaxx
Thank You For Choosing Our Projector Screen.
Please Read This Manual Carefully Before Using Your Screen.
Deluxe Tripod Screen

THANK YOU FOR CHOOSING OUR DELUXE TRIPOD SCREEN.
All of our screens are inspected against very strict quality standards. We are
confident that you will be fully satisfied with your selection. Please take a few
minutes to carefully read this manual before using your screen. Enjoy!
TRIPOD WALL SCREEN
Hanging Line (00-02)
Screen (00-03)
End Cap (00-04)
Housing (00-05)
Keystone
Eliminator
(00-06)
Extension
Tube (00-08)
Vertical
Adjuster
(00-09)
Bottom
Tube
(00-10) Carrying
Handle/
Adjuster
(00-12)
Housing
Attachment
& Set Screw
(00-11)
Tripod Base (00-13)
Pull Slat (00-01)
Figure 1.0: Closed
screen in travel mode
Figure 1.1: Open
screen in display mode
Figure 1.2: Tripod Shown
Without Screen
1
Storage
Nub
(00-07)

2
ASSEMBLY INSTRUCTIONS
·Release the tripod base and extend the support feet. (Figure 2.0, 2.1)
·Remove the set screw from the receiving collar (A) on the housing
attachment.
·Mount the screen by lining up the mounting stud (B) on the back of the
screen housing to the receiving collar (B) the tripod housing
attachment.
·Fully insert stud and tighten the set screw (C) in place.
·After tightening the set screw the screen can be rotated 90° to
switch between storage and display mode.
Screen
Housing
(B) Receiving Collar
(A) Mounting Stud
(C) Set Screw

3
OPERATING INSTRUCTIONS
·Release the tripod base and extend the support feet. (Figure 2.0, 2.1)
·Rotate the screen housing 90° from its vertical position (store) to its
horizontal position (display). (Figure 2.1) Make sure the housing is
secured to the housing attachment (00-11) before pulling out the
screen (i.e. complete assembly instructions first).
·Partially pull out the screen and hook the hanging line (00-02) over the
keystone eliminator (00-06).
·With one hand on the extension tube (00-08) use the other hand to
loosen the vertical adjuster (00-09), then pull up on the extension tube
until you have reached the desired vertical position and then tighten
the vertical adjuster (00-09).
·The housing attachment/carrying handle (00-11/00-12) is designed to
allow for vertical adjustment of the screen housing along the bottom
tube. Loosen the clip on the carrying handle and lower the screen to
the desired vertical position, then snap the adjuster clip back into
place.
·To store the screen simply follow the above directions in reverse.
·NOTE: To maximize the life of your tripod screen always use slow and
smooth actions when opening and closing the screen.
Figure 2.0 Figure 2.1 Figure 2.2 Figure 2.3

4
TRIPOD WALL SCREEN
SCREEN MAINTENANCE & PROPER OPERATING CONDITIONS
·The screen surface may be cleaned with warm water and a soft
cotton cloth.
·To prevent marring or smudging the screen surface be careful
no to touch the screen surface with your fingers or any object
(i.e. pointing device)
·Do not display or store your screen in direct sunlight.
·Do not display your screen in front of a door, window, fan or
heating or cooling vent as air flow will disrupt
your viewing experience, and direct sunlight could cause fading.
·Handle the screen carefully to avoid damage and prolong the life
of your screen.
TECHNICAL DATA
PROJECTOR
LUMINOUS METER
SCREEN
Viewing Angle Measurement: refer the figure below
Standard: JB/T8389 issued by Ministry of Machinery Industry
Matte White Screen
Gain: 0.9
Viewing Angle: >160
High color rendering, high resolution.
Gain Measurement: refer the diagram below
Standard: JB/T8389 issued by Ministry of Machinery Industry
PROJECTOR
Height
Direction
LUMINOUS METER
SCREEN
STANDARD BOARD