Red Arrow FLSMDPC10BOPI User manual

EnduraLED Polycarbonate
Floodlights with PIR
Installation Instructions P.1
Red Arrow Trading
Elsworth House, Herries Road South, Sheffield,
S6 1QS
T: 0800 195 0006 F: 0870 043 3946
E: [email protected] www.redarrowtrading.com
This installation must be carried out by an electrician. Please read these instructions carefully
before installation. Leave a copy for the user/maintenance engineer for future reference.
For models: FLSMDPC10BOPIR, FLSMDPC20BPIR,
FLSMDPC30BPIR, FLSMDPC50BPIR
Safety Instructions
•Ensure the power supply is switched off before
installation.
•Do not install this floodlight where the ambient
temperature may be over 45°C
•This floodlight must be mounted on a non-flammable
surface.
•Ensure adequate ventilation is allowed between
floodlight and any object above, in front or to either
side. Suggested space is 0.5m above, 0.3m to either
side & 1.0m in front.
•The floodlight can become hot during use. Allow
adequate cooling time before handling.
•This floodlight is of Class I construction and must
be earthed.
•Do not use this floodlight if it appears damaged in
any way. Broken or damaged glass must be replaced
immediately.
•This floodlight must be installed in accordance with
the current edition of the IEE Wiring Regulations.
If in doubt, contact a qualified electrician.
Specification
• Voltage: 220V-240V
• Wattage: 10-50W
• LED: 15-75pcs of LF SMD LED
• Lumen Output: 800-4000lm
• Life expectancy: 50000 hours
• Guarantee: Two years
• IP Rating: IP65
Installation Instructions
• Find a suitable location to install this product.
• Use the mounting bracket as a template to mark fixing
holes.
• Drill fixing holes and fit suitable wall plugs, and secure
floodlight in location.
• Feed the flexible cable to the required location for
termination.
• When connecting the cable to the power supply, ensure the
correct polarity is observed.
- Brown to live (L)
- Blue to neutral (N)
- Green / Yellow to earth ( )
• Adjust the floodlight to the desired angle and tighten the
bolts using a suitable allen / hex key.
• Switch on power supply and check floodlight operation.
Maintenance Instructions
•There are no user serviceable parts in this fitting.
•Periodically clean the housing and lens with a clean damp
cloth and dry with a lint free cloth.
PIR Specification
• 100-240V AC Power source
• 50/60Hz Power frequency
• Maximum 500W resistive load / maximum 200W inductive
load
• 90° Detection range
• Maximum eight metres (adjustable) detection distance
• Delay time adjustable between 10 seconds - 5 minutes
(5 seconds - 1 minute adjustable)
• 2~2000Lux (adjustable) Lux control
• 0.6-1.5m/s Detection motion speed
• -10°C - +40°C Working temperature
• 1-3 metres installation height
Manual Override PIR Sensor
Instructions
Technical requirements:
This lamp has two modes:
1. PIR Sensor mode:

EnduraLED Polycarbonate
Floodlights with PIR
Installation Instructions P.2
For models: FLSMDPC10BOPIR, FLSMDPC20BPIR,
FLSMDPC30BPIR, FLSMDPC50BPIR
Red Arrow Trading
Elsworth House, Herries Road South, Sheffield,
S6 1QS
T: 0800 195 0006 F: 0870 043 3946
E: [email protected] www.redarrowtrading.com
PIR Sensor Control
Delay Settings:
• Delay time adjustable between 10 seconds - 5 minutes (5 seconds - 1 minute adjustable)
• Maximum physical adjustable angle of 270°.
• When the light is on, product will reset delay time and keep the light on when detected new signal.
• When the light is off, it requires four seconds to re-stabilise.
Detection Illumination Settings:
• Detect environment illuminance range 2-2000lux.
• Max adjustable angle of 270°.
Detection Distance Settings:
• Detect distance is maximum eight metres adjustable.
• Max adjustable angle of 270° (physical).
On the rear of the sensor are dials:
1. Lux - Provisionally turn the control fully to the moon symbol, in this setting the sensor is inactive during daylight. At
dusk, when the light level is at the desired level, adjust the dial towards the sun symbol until the floodlight turns on.
Note: This fitting does not have a walk test facility. Even with the dial turned fully clockwise, the light may not switch on
during bright conditions.
2. Time - Turn the dial fully anti-clockwise, the floodlight will stay on for five seconds. Turn the dial fully clockwise, the
floodlight will stay on for six minutes.
3. Sensitivity - Turn the dial fully anti-clockwise for a one metre detection distance. Turn the dial fully clockwise for a
detection distance of eight metres.
1.1. Switch on power supply, the sensor will stabilise for 15 seconds.
1.2. The lamp will light on and off twice automatically then default to sensor mode. When the following two conditions
occur simultaneously the lamp will be lit:
1.2.1. Ambient light is lower than the setting value (LUX).
1.2.2. Movement of a live body or warm object within the detection area.
2. Manual override (pulse override).
2.1. Turn off the switch then turn on quickly, make sure the interval time is shorter than six seconds.
2.2. The lamp will switch to normal lighting mode enabling continuous lighting without the use of the sensor function
until user switches off.
Note: The sensor mode and normal lighting mode could be cyclically switched, if the power-off time is over ten seconds,
the sensor will default to the sensor mode again when in a power-on state.
Guarantee
This product is guaranteed for a period of two years from the date of purchase. The guarantee is invalid in the case of improper use, tampering, removal of the Q.C. date label, installation
in an improper working environment or installation not according to the current edition of the I.E.E. Wiring Regulations (BS7671). The guarantee is also invalidated if the luminaire has
been Mega tested. Should this product fail during the guarantee period it will be replaced free of charge, subject to correct installation and return of the faulty unit. We do not accept
responsibility for any installation costs associated with the replacement of this product. We reserve the right to alter specifications without prior notice.
Product is suitable for
mounting on flammable
material
F
Product complies with
all relevant European
standards
PRN WEE/BJ1331XR
Attention:
Adjust the three function dials with caution to avoid damage.