Redpro RP-BP85D User manual

Caution On use
• Never short-circuit the battery pack terminals.
• Never attempt to open the battery pack.
• Avoid mechanical shock.
• Please consult the store where you purchased this battery pack or
your sales representative before using the battery pack in a product
whose Operation Manual/Operating Instructions does not explicitly
state that the battery pack can be used, or before using the battery
pack in conjunction with another power supply. In appropriate use of
the battery pack may result in unit misoperation.
• The internal impedance of the battery pack increases as the
temperature drops to 5°C (41°F) or below. This may result in a shorter
operating time or the failure of the component to which it is connected
to turn on. This phenomenon occurs more frequently in battery packs
that have been charged many times than in new ones.
• The performance and operating time of the battery may drop under
cold conditions. When this happens, do the following to extend the
operating time of the battery pack:
- Charge the battery pack only with REDPRO charger model RP-DC50
or any other model dedicated to the RP-BP85D within a temperature
range of 10°C to 30°C (50°F to 86°F).
• Large discharge amount may expedite deterioration of battery pack’s
internal cells. To prevent this, use the RP-BP85D with discharger
amount of about 3 A or less.
• The maximum discharge amount is 3.5 A for the RP-BP85D at 23°C
(73°F). Continuous use at levels beyond the maximum discharge level
may cause the protection circuit to shut off the current to protect the
Testing the capacity of the Battery pack:
- The remaining capacity is indicated by a four-step Red LED Dysplay
- Press the Test / Check Button and the remaining Capacity of the
Battery Pack will be displayed on LED Dysplay ( more than 80%, 60%,
40%,below 20%) F - more than 80% , E - below 20%
- If the Battery Pack is instilled on the Camcorder with function of
powering the camera, the LED Power Dysplay may not show exact
capacity status of the battery pack.
- When only one(E) LED indicates please recharge the battery as soon
as possible.
- The D-TAP DC Output socket can
be used as 14.4V DC output, or DC
charging input
- Open the rubber protective cover
with D-TAP sign on it.
- Plug in the D-Tap lead for DC
output, or for charging the battery .
-To keep D-Tap socket away from
dust close the D-Tap output with
rubber protective cover
- The Battery offers 5V/1A USB
Power Output for charging mobile
phones and all other units on USB.
- Open the rubber protective cover
with USB sign on it.
- Plug in the USB lead and connect
with device that need to be charged.
- Press the CHECK Button to switch
on the USB charging.
- To keep USB socket away from
dust close the D-Tap output with
rubber protective cover.
RP-BP85D
Battery Pack Operating Instructions
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
Important Safety Instructions
• Keep these instructions.
• Heed all warnings.
• Follow all instructions.
• Do not use this apparatus near water.
• Clean only with dry cloth.
• Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
• Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other. A
grounding-type plug has two blades and a third grounding prong. The
wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
• Only use attachments/accessories specified by the manufacturer.
Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use
caution when moving the cart/apparatus combination to avoid injury
from tip-over.
• Unplug this apparatus during lightning storms or when unused for
long periods of time.
• Refer all servicing to qualified service personnel. Servicing is
required when the apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or
objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
Overview / Features
The RP-BP85D Battery Pack uses Lithium-Ion Battery Cells.
Use the RP-BP85D Battery Pack only with equipment whose
Operation Manual/Operating Instructions recommends its use.
Caution On charging
• The battery pack can be charged within a temperature range of 0°C
to 40°C (32°F to 104°F). However, we recommend charging within a
temperature range of 10°C to 30°C (50°F to 86°F) to ensure optimum
battery performance.
• The battery pack discharges naturally over time. To prolong the life of
the product, it is recommended that you fully charge the battery pack
before using it. For details on the charging procedure, refer to the
Operation Manual/Operating Instructions supplied with the battery
charger.
• The battery pack may become warm in use or while being charged.
This is normal.
You can use SONY original charger or REDPRO Dual Channel
charger RP-DC50 to charge the RP-BP85D Battery Pack. If you want to know more about REDPRO Products please visit our
website: www.red-pro.com
RP-BP85D
POWER METER
F E
POWER METER - LED Indicator
USB 5V , 1A Power Output
D-Tap 14.4V , 50W, 3.5A Power Output
SPECIFICATION:
Test / USB Button
LED Light Indicator
USB
CHECK
D-Tap
Battery type: Lithium-ion Rechargeable Battery
Power meter: 4-level LED Power indicator
Maximum voltage: 16.4 V DC
Nominal voltage: 14.4 V DC
Battery Capacity: 74.88 Wh
USB Output: 5V, 5W / 1A max
D-Tap DC Output: 14.4V, 50W / 3.5A max
Charging time: approx. 200 minutes on RP-DC50
Operating temperature: –20°C to +45°C (–4°F to +113°F)
Dimensions (w/h/d) 41.5 × 90.5 × 69.7 mm
Net Weight: 420 g

For the customers in Europe
This product with the CE marking complies with the EMC Directive
issued by the Commission of the European Community.
Compliance with this directive implies conformity to the following
European standards:
• EN55103-1: Electromagnetic Interference (Emission)
• EN55103-2: Electromagnetic Susceptibility (Immunity)
This product is intended for use in the following Electromagnetic
Environments:
E1 (residential),
E2 (commercial and light industrial),
E3 (urban outdoors),
E4 (controlled EMC environment, ex. TV studio).
To the purchasers of the RP-BP85D
The RP-BP85D Lithium-ion Battery Pack has a rated capacity of less
than 100 Wh. It can thus be transported as a non-hazardous lithium-ion
battery. Related laws and regulations are, however, subject to change.
For detailed conditions regarding the transport of battery packs, please
consult your respective air transport company.
Caution: Do not handle damaged or leaking Lithium-Ion batteries
For the customers in Canada
This Class B digital apparatus complies with Canadian ICES-003.
For the customers in the U.S.A.
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
You are cautioned that any changes or modifications not expressly
approved in this manual could void your authority to operate this
equipment
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may
cause undesired operation.
If you want to know more about REDPRO Products please visit our
website: www.red-pro.com
RP-BP85D
Info Lithium-Ion
Battery Pack
To the purchasers of the RP-BP85D
The RP-BP85D Lithium-ion Battery Pack has a rated capacity of less
than 100 Wh. It can thus be transported as a non-hazardous lithium-ion
battery. Related laws and regulations are, however, subject to change.
For detailed conditions regarding the transport of battery packs, please
consult your respective air transport company.
-When an excessive current flow is caused by overloading or short
circuited terminals
- When the voltage drops to 11 V or lower and results in the cessation of
current output.
• Once the protection circuit has tripped, the battery pack will not return
to normal automatically. To cancel the effect of the protection circuit,
you must charge the battery pack with charger dedicated to the lithium-
ion battery packs.
Caution On storage
• Never expose the battery pack to rain or moisture.
• Keep away from children.
• Never expose the battery pack to temperatures above 60°C (140°F).
Store the battery pack in dry place at temperatures between 0°C to
23°C (32°F to 73°F).
• If the battery pack is to be stored for a short period (approximately
more than 24 hours and a month or less), discharge the battery pack to
90% of its full capacity to prevent deterioration of battery pack’s internal
cells.
• When storing the battery pack for an extended period (more than a
month),
• it is recommended that you discharge the battery pack to about 50%
of its full capacity. (The two LED light up RED) While the battery pack is
stored, charge it until the capacity reaches 50% once in 6 months.
• If the battery pack terminals become soiled, clean them with a soft
cloth.
WARNING
• Batteries shall not be exposed to excessive heat such as sunshine.
fire or the like.
Battery life
• Battery life may be shortened due to storage or operation in high
temperatures, storage with its full capacity, and frequent use.
• Renew the battery pack when the operating time with a completely
charged battery pack becomes noticeably short or all LEDs flash green
because the self-diagnostics function has detected the end of battery
life. If a Battery pack is deteriorated, all LEDs may not light when the
CHECK button is pressed just after charging is completed.
Self-diagnostic function
When an abnormality is detected, all the LEDs flash in Red. If
this happens, stop using the battery pack immediately. Once the
LEDs start flashing, the battery pack cannot be recharged
Note
Always verify that the unit is operating properly before use.
REDPRO WILL NOT BE LIABLE FOR DAMAGES OF ANY KIND
INCLUDING, BUT NOT LIMITED TO, COMPENSATION
OR REIMBURSEMENT ON ACCOUNT OF THE LOSS OF
PRESENT OR PROSPECTIVE PROFITS DUE TO FAILURE OF
THIS UNIT, EITHER DURING THE WARRANTY PERIOD OR
AFTER EXPIRATION OF THE WARRANTY, OR FOR ANY
OTHER REASON WHATSOEVER