ReelCraft A5850 OLPSMR User manual

INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Operating Instructions
Series 5005 Spring Driven Hose Reels
Side Mount Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 1233-1011 Rev: 3/2018
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
A5850 OLPSMR A5850 OLPSML
Dimensions
ABCDE
6 4/5” 16 1/2” 17 7/8” 15 7/8” 1 1/4”
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY

Series 5005 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Part # # Req. Description Item #Part # # Req. Description Item #Part # # Req. Description
1 S82-15 17 Lock Nut 12 3-117440 1 U-Bolt 22 262489 1 Side Mount Plate
2 S400109 1 Latch Plate Assembly 13 260151 1 Sheave Disc 23 S82-15 6 Hex Lock Nut
3 S400012 1 Latch Bushing 14 S400017 1 Spring Arbor 24 300002 9 Machine Screw
5 S400018 1 Latch Plate Spring 15 S300011 10 Hex Lock Nut 26 262518 1 Main Shaft
6 S300011 1 Hex Lock Nut 16 602439 1 Spring Case Cover 27 S137-12 1 Snap Ring
7 S400021 1 Latch Plate Bumper 17 300034 2 Wear Washer 28 300031 1 Snap Ring
8 602444 1 Swivel Assembly 18 S261360 1 Spring Case Stud 29 S600247 1 Guide Arm
9 902016 3 Lock Washer 19 S600050 1 Drive Spring Assembly 30 S500019 1 Latch Cam
10 3-117440 1 Sheave Flange 20 602436 1 Spring Case Assembly 31 260445 1 Spool Spacer
11 261650-1 2 Lock Nut 21 300006 1 Set Screw 32 S2-48 3 Hex Cap Screw
Item
#Description # Req. A5850 OLPSMR A5850 OLPSML
Hose Assembly 1 601022-50 601022-50
Bumper Stop Assembly 1 2-HR1004-3 2-HR1004-3
Max. Operating Pressure 300 PSI 300 PSI
Max. Operating Temperature 150 °F 150 °F