ReelCraft 5650 OLPSMR User manual

INSTALLATION: A flexible hose connection must be used between the hose reel inlet and the source of supply to prevent possible
misalignment and binding.
LUBRICATION: Hose reel spring and bearings are factory lubricated and require no further lubrication.
REPLACING HOSE: 1. Wind spool flange clockwise-facing swivel-until spring is tight.
2. Back off three turns and latch.
3. Insert hose through roller guide.
4. Connect hose fitting to swivel joint and secure hose with clamps.
ADJUSTMENTS: To adjust spring tension, add or remove wraps of hose from the spool, one wrap at a time until desired tension is
obtained.
REPAIRS: Extensive repairs should be performed only by an authorized serviceman or factory to avoid damage which may
void your warranty. Remove all spring tension before beginning disassembly process.
Operating Instructions
Series 5005 Spring Driven Hose Reels
Side Mount Model Numbers:
Reelcraft Industries, Inc. • 2842 E Business Hwy 30, Columbia City, IN 46725
Ph: 800-444-3134 / 260-248-8188 • Fax: [phone]
Customer Service: 855-634-9109 • [email protected] • www.reelcraft.com
Form# 1232-1011 Rev: 3/2018
MOUNTING: The hose reel is equipped with a universal mounting bracket so that it can be mounted on the floor, wall or
ceiling; whichever place is convenient. The hose guide arm can be moved to the position desired by removing
the screws fastening the guide bracket to the reel base. Shift the guide arm bracket so the hose comes off the
reel at the desired position and replace the screws.
5650 OLPSMR A5835 OLPSMR
5650 OLPSML A5835 OLPSML
Dimensions
ABCDE
5 4/5” 16 1/2” 17 7/8” 15 7/8” 1 1/4”
1. Do not use reel at higher pressures or temperatures than listed on
the back of this bulletin.
2. Remove all spring tension before beginning dissassembly process.
SAFETY

Series 5005 Spring Driven Hose Reels
Page 2 www.reelcraft.com
Item
#Part # # Req. Description Item #Part # # Req. Description Item #Part # # Req. Description
1 S82-15 1 Lock Nut 13 260151 1 Sheave Disc 22 262489 1 Side Mount Plate
2 S400109 1 Latch Plate Assembly 14 S260648 1 Spring Arbor 23 S82-15 7 Hex Lock Nut
3 S400012 1 Latch Bushing 15 S300011 10 Hex Lock Nut 24 300002 9 Machine Screw
5 S400018 1 Latch Plate Spring 16 602439 1 Spring Case Cover 26 602555 1 Main Shaft
6 S300011 1 Hex Lock Nut 17 300034 2 Wear Washer 27 S137-12 1 Snap Ring
7 S400021 1 Latch Plate Bumper 18 S261360 1 Spring Case Stud 28 300031 1 Snap Ring
10 260149 1 Sheave Flange 19 S600050 1 Drive Spring Assembly 29 S500107 1 Guide Arm
11 261650-1 2 Lock Nut 20 602436 1 Spring Case Assembly 30 S500019 1 Latch Cam
12 3-117440 1 U-Bolt 21 300006 1 Set Screw 32 S295-102 3 Self Tapping Screw
Item
#Description # Req. 5650 OLPSMR 5650 OLPSML A5835 OLPSMR A5835 OLPSML
8Swivel Assembly 1 602330 602330 602444 602444
9Lock Washer 3 None None None None
31 Spool Spacer 1 None None None None
Hose Assembly 1 S601013-50 S601013-50 601021-35 601021-35
Bumper Stop Assembly 1 1-HR1004 1-HR1004 2-HR1004-3 2-HR1004-3
Max. Operating Pressure 300 PSI 300 PSI 300 PSI 300 PSI
Max. Operating Temperature 150 °F 150 °F 150 °F 150 °F