Regency Fireplace Products LRI3E-LP1 Quick start guide

Liberty®LRI3E / Regency Horizon®HRI3E
Gas Insert
Owners &
Installation Manual
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
www.regency-re.com
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
MODELS: LRI3E-NG1 Natural Gas LRI3E-LP1 Propane
HRI3E-NG1 Natural Gas HRI3E-LP1 Propane
919-826a FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 07.24.18
All manuals and user guides at all-guides.com
all-guides.com

2| LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
2
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.
The Regency Gas Insert Series of hand crafted appliances has been designed to provide you with all the warmth and
charm of a fireplace, at the flick of a switch. The models LRI3E / HRI3E of this series have been approved by Warnock
Hersey/Intertek for both safety and efficiency. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow.
Please take a moment now to acquaint yourself with these instructions and the many features of your
Regency Fireplace.
This product may be installed in an aftermarket, perma-
nently located,manufacture home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 3
| 3
table of contents
HRI3E optional log set installation ...............................22
LRI3E log set installation ...........................................24
Brick panel installation .................................................26
Painted black and enamel panel installation ................27
Glass door removal / installation..................................28
Vignette faceplate with Safety screen installation ........29
Inlay installation ...........................................................30
Backing plate installation .............................................32
Optional hearth trim installation ...................................33
Optional mantel deflector installation ...........................33
First Fire ......................................................................34
Operating Instructions
Operating Instructions .................................................34
Coding/Pairing of remote control transmitter with on/off
switch ...........................................................................34
Lighting Procedure ......................................................35
Shutdown Procedure ...................................................35
Normal Operating Sounds of Gas Appliances .............36
Maintenance
Maintenance Instructions ............................................36
Copy Of Lighting Instruction Plate ...............................37
Proflame II Remote Control Operating Instructions 38-41
Door Glass ..................................................................42
Pilot Adjustment ...........................................................43
General Vent Maintenance ..........................................43
Log Replacement ........................................................43
Glass Gasket ...............................................................43
Backup battery Pack ....................................................43
Fan replacement - with remote control ........................44
Valve replacement .......................................................45
Parts
LRI3E parts list ............................................................47
LRI3E Main Assembly .................................................48
HRI3E Parts list ...........................................................49
HRI3E Main assembly .................................................50
Accessories .................................................................51
Warranty
Warranty ......................................................................53
Dimensions
Unit dimensions with vignette faceplate ........................4
Unit dimensions with vignette faceplate
+ small backing plate ....................................................4
Unit dimensions with 4 sided vignette faceplate
+ backing plate .............................................................5
Copy of Safety Label HRI3E ..........................................6
Copy of Safety Label LRI3E ..........................................7
MA Code - CO Detector ................................................8
Installation
Important Message ......................................................9
Before You Start .............................................................9
Important Message ......................................................9
For Your Safety ..............................................................9
Specifications ................................................................9
Gas Pressure Testing ..................................................10
Installation Into A Solid Fuel Burning Fireplace
Or Factory Built Fireplace ............................................10
Factory-Built (Metal) Wood-Burning Fireplace
Requirements ..............................................................10
Installation Checklist ....................................................11
Materials Required ......................................................11
Minimum Fireplace Dimensions ..................................11
Minimum Clearances to combustibles .........................12
Gas Connection ...........................................................13
Alternate Approved Caps/Adaptor ...............................14
Standing pilot ..............................................................14
Vent restrictor plate Installation ...................................14
Flue / vent installation ..................................................15
Air shutter Adjustment .................................................16
System with fan (LRI3E / HRI3E) ................................17
High Elevation ..............................................................18
Gas Line Installation ....................................................18
Pilot Adjustment ...........................................................18
Gas Pipe Pressure Testing ..........................................18
885 S.I.T. Valve Description .........................................18
Conversion from NG to LP .........................................19
Media installation .........................................................21
All manuals and user guides at all-guides.com

4| LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
4dimensions
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE + SMALL BACKING PLATE
10-3/8”
29-1/16"
22-3/4"
22-1/2"
26"
19”
28"
14"
21-5/16"
1-13/16”
(711mm)
(540mm)
(355mm)
(738mm)
(660mm)
(572mm)
(576mm)
(45mm)
(262mm)
(482mm)
10-3/8"
(262mm)
(482mm)
19"
738mm
29-1/16”
794mm
31-1/4”
23 -3/8” 593 mm
14
-1/4”
36 2mm
22-11/16”
576mm
21-5/16”
540mm
711mm
28”
1-7/8”
47mm
Not Shown:
Regular backing plate - 35-3/4" W x 25-5/8" H
Oversize backing plate - 38-3/16" W x 29-5/8" H
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 5
| 5
dimensions
UNIT DIMENSIONS WITH 4 SIDED VIGNETTE FACEPLATE + BACKING PLATE
28-5/8”
726mm
29-1/4”
743mm
35-3/4”
908mm
28”
711mm
21-5/16”
540mm
1-15/16”
48mm
10-3/8”
262mm
3”
76mm
19”
482mm
14”
355mm
3”
76mm
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.
All manuals and user guides at all-guides.com

6| LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
6dimensions
This is a copy of the labels that accompany each HRI3E Gas Insert. We
have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a difference, the label on the unit is the correct one.
NATURAL GAS FIREPLACE INSERT: MODEL HRI3E-NG1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 5" WC (1.25 kpa)
Low Setting Man. pressure 1.6" WC (0.40 kpa)
Max. Manifold pressure 3.5" WC (0.87 kpa)
Orifice size #45 DMS
Minimum input 14,000 Btu/h (4.10 kW)
Maximum input 19,500 Btu/h (5.71 kW)
PROPANE GAS FIREPLACE INSERT: MODEL HRI3E-LP1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 11" WC (2.73 kpa)
Low Setting Man. pressure 6.4" WC (1.59 kpa)
Max. Manifold pressure 10" WC (2.49 kpa)
Orifice size #55 DMS
Minimum input 15,500 Btu/h (4.54 kW)
Maximum input 19,000 Btu/h (5.57 kW)
Model/Modèle: HRI3E-NG1
919-799
Part #: 919-799
Colour: Black on grey except what is highlighted is printed red
Size: (File at 100%) 6.495"W x 8.66" H
Material: 2 ml silver matt polyester (DPM SMS)
Jun 26/2017: Created draft
Sept 15/2017: Rating modified
Mar 12/18: Updated standard format
Apr 4/18: Updated company name
*Printer - continue serial sequence from 919-692
DO NOT REMOVE THIS LABEL /
NE P
AS ENLEVER CETTE ÉTIQUETTE
Serial No. / No de série
448
448
Duplicate Serial number/Copie No de série
Listed: VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION
Certified to/Certifi pour : éCSA 2.17-2017
ANSI Z21.88-2016
CSA 2.33-2016
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE.
Model/Modèle: HRI3E- LP1
É ÉQUIP EN USINE POUR GAZ PROPA
NE
MODÈLE HRI3E-LP1
É ÉQUIP EN USINE POUR GAZ NATUR
EL
MODÈLE HRI3E-NG1
Pression d'alimentation minimum
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimumé
D bit calorifique maximumé
Min. Hearth Depth/
Prof. min. âtre D
12” (305mm)
Min. Hearth Width/
Largeur min. âtre E 36”
(914mm)
Max. Mantle Depth/
Prof. max. manteau G 12"
(305mm)
Mantel Clearances / Dégagements manteau
FPI Fireplace Products International, Ltd
Delta BC, CANADA
Side wall /mur latéral A 6” (152mm)
Ceiling/Plafond B 60” (1524mm)
Mantel/Manteau C 38” (965mm)
Min. Alcove Width/
Largeur min. alcôve K 54" (1372mm)
Max. Alcove Depth/
Prof. max. alcôve L 36” (914mm)
MADE IN CANADA /FABRIQUÉ
AU CANADA
Minimum Clearances to Combustibles
from Insert/Dégagements min. combustibles
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code,
ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases unless a certified kit is used.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located,
manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details
WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all
original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Cet appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, conformément au National Fuel
Gas
Code ANSI Z223.1, ou au CSA-B149.1 en vigueur.
Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une
maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour
plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.
AVERTISSEMENT : Ce foyer a été converti pour être utilisé avec un foyer au gaz encastrable et ne peut être utilisé pour brûler du bois ou
d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remises en place et que le foyer ait été homologué de nouveau par une
autorité
compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à
évacuation.
For use with glass doors certified with the appliance only. Pour utilisation uniquement avec les portes en verre certifiées avec
l'appareil.
For use only with barrier (Part # 716-010) Follow installation instructions. Pour utilisation uniquement avec l’écran(Pièce n°716-010)
Suivre les consignes d'installation.
C # 4001172
Pression d'alimentation minimum
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimumé
D bit calorifique maximumé
Electrical supply / Alimentation électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 911-207/Pièce ventilateur
A
C
B
E
K
D
L
G
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.
COPY OF SAFETY LABEL HRI3E
All manuals and user guides at all-guides.com
all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 7
| 7
safety decal
This is a copy of the labels that accompany each LRI3E Gas Insert. We
have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a difference, the label on the unit is the correct one.
NATURAL GAS FIREPLACE INSERT: MODEL LRI3E-NG1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 5" WC (1.37 kpa)
Low Setting Man. pressure 1.6" WC (0.40 kpa)
Max. Manifold pressure 3.5" WC (0.87 kpa)
Orifice size #45 DMS
Minimum input 14,000 Btu/h (4.10 kW)
Maximum input 20,500 Btu/h (6.00 kW)
PROPANE GAS FIREPLACE INSERT: MODEL LRI3E-LP1
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 11" WC (2.73 kpa)
Low Setting Man. pressure 6.4" WC (1.59 kpa)
Max. Manifold pressure 10" WC (2.49 kpa)
Orifice size #55 DMS
Minimum input 15,500 Btu/h (4.54 kW)
Maximum input 19,000 Btu/h (5.57 kW)
Model/Modèle: LRI3E-NG1
919-801
Part #: 919-801
Colour: Black on grey except what is highlighted is printed red
Size: (File at 100%) 6.495"W x 8.66" H
Material: 2 ml silver matt polyester (DPM SMS)
Jun 26/2017: Created draft
Mar 12/18: Updated standard format
Apr 4/18: Updated company name
*Printer - continue serial sequence from 919-693
DO NOT REMOVE THIS LABEL
/
NE P
AS ENLEVER CETTE ÉTIQUETTE
Serial No. / No de série
449
449
Duplicate Serial number/Copie No de série
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE.
Model/Modèle: LRI3E- LP1
É ÉQUIP EN USINE POUR GAZ PROP
ANE
MODÈLE LRI3E-LP1
É ÉQUIP EN USINE POUR GAZ NATU
REL
MODÈLE LRI3E-NG1
Pression d'alimentation minimum
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimumé
D bit calorifique maximumé
Min. Hearth Depth /
Prof. min. âtre D
12” (305mm)
Min. Hearth Width/
Largeur min. âtre E 36”
(914mm)
Max. Mantle Depth/
Prof. max. manteau G 12"
(305mm)
Mantel Clearances / Dégagements manteau
Side wall /mur latéral A 6” (152mm)
Ceiling/Plafond B 60” (1524mm)
Mantel/Manteau C 38” (965mm)
Min. Alcove Width/
Largeur min. alcôve K 54" (1372mm)
Max. Alcove Depth/
Prof. max. alcôve L 36” (914mm)
MADE IN CANADA /FABRIQUÉ
AU CANADA
Minimum Clearances to Combustibles
from Insert/Dégagements min. combustibles
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code,
ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases unless a certified kit is used.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located,
manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details
WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all
original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Cet appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, conformément au National
Fuel Gas
Code ANSI Z223.1, ou au CSA-B149.1 en vigueur.
Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une
maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour
plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.
AVERTISSEMENT : Ce foyer a été converti pour être utilisé avec un foyer au gaz encastrable et ne peut être utilisé pour brûler du bois ou
d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remises en place et que le foyer ait été homologué de nouveau par une
autorité
compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à
évacuation.
For use with glass doors certified with the appliance only. Pour utilisation uniquement avec les portes en verre certifiées avec
l'appareil.
For use only with barrier (Part # 716-010) Follow installation instructions. Pour utilisation uniquement avec l’écran(Pièce n°716-010)
Suivre les consignes d'installation.
Pression d'alimentation minimum
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimumé
D bit calorifique maximumé
Electrical supply / Alimentation électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 91
1-207/Pièce ventilateur
A
C
B
E
K
D
L
G
C # 4001172
Listed: VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION
Certified to/Certifi pour : éCSA 2.17-2017
ANSI Z21.88-2016
CSA 2.33-2016
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
FPI Fireplace Products International, Ltd
Delta BC, CANADA
For the State of Massachusetts, installation and repair must be done by a plumber or gasfitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.
COPY OF SAFETY LABEL LRI3E
All manuals and user guides at all-guides.com

8| LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
8requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 9
| 9
installation
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The LRI3E / HRI3E Gas Inserts must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual first. Consult the
"authority having jurisdiction" to determine the need
for a permit prior to starting the installation. It is the
responsibility of the installer to ensure this fireplace
is installed in compliance with manufacturers
instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following:
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL,ETC.IT IS IMPERATIVETHAT
CONTROLCOMPARTMENTS,BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
IFTHE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITHTHE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
PRIORTOOPERATINGTHEAPPLIANCE.
FOR YOUR SAFETY
This appliance requires air for proper combustion.
Always provide adequate combustion and ventilation
air. Follow instructions and information in CAN/CGA
B149 (in Canada) or the National Fuel Gas Code
ANSI Z223.1 (in the USA), regarding requirements
for combustion and ventilation air.
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit must
be disconnected.
Gas Max. Input Capacity:
Natural Gas HRI3E 19,500 Btu/h
LRI3E 20,500 Btu/h
Propane HRI3E 19,000 Btu/h
LRI3E 19,000 Btu/h
Min. Input
Natural Gas HRI3E 14,000 Btu/h
LRI3E 14,000 Btu/h
Propane HRI3E 15,500 Btu/h
LRI3E 15,500 Btu/h
Fuels: Approved for use with both natural gas,
and propane. Approved as is for use at 0' to 4,500'
(0-1370m).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 140 CFM.
Log Set: Ceramic fibre, 7 per set - LRI3E
Glass Crystals: 4lbs of glass crystals - HRI3E
Optional Log Set: Ceramic fibre, 5 per set + 4lbs
of glass crystals - HRI3E
Vent System: 2" intake with 3" exhaust.
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and was
determined independent of any installed system.
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Regency Gas Insert must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual first. Consult the
building authority having jurisdiction to determine
the need for a permit prior to starting the installation.
NOTE: Failure to follow the instructions could cause
a malfunction of the heater which could result in
death, serious bodily injury, and/or property damage.
Failure to follow these instructions may also void
your fire insurance and/or warranty.
All manuals and user guides at all-guides.com

10 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
10 installation
General Safety Information
1. The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the National
Fuel Gas Code ANSI Z223.1 in the U.S.A. This
appliance should be installed by a qualified gas
fitter technician only.
2. Installation and repair should be done by a
qualified service person.
3. The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
4. See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible fireplace.
5. This appliance is listed for bedroom installations
when used with a listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6. Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
7. Inspect the venting system annually for blockage
and any signs of deterioration.
8. Any glass removed for servicing must be
replaced prior to operating the appliance.
9. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
10. This appliance cannot be operated without brick
or enamel panels in place.
11. Due to high temperatures, the appliance should
be located out of high traffic areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the fireplace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other flammable material should not be placed
on or near the appliance.
GAS PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa).
INSTALLATION INTO A SOLID FUEL
BURNING FIREPLACE OR FACTORY
BUILT FIREPLACE
The LRI3E / HRI3E Gas Inserts have been tested
and approved to be vented into any masonry fire-
place or approved solid fuel burning factory built
fireplace that will allow the insert to physically fit into
the firebox. Refer to "Minimum Fireplace Dimen-
sions" section for minimum fireplace clearances.
If the factory built fireplace* height is too low for
your Insert, you may remove the smoke baffle
plate, damper, refractory (firebricks), glass doors,
screen rails, screen mesh and log grates from the
factory built fireplace as long as these items are
saved and are reinstalled in the event that the Insert
is removed. The fireplace flue damper can be fully
blocked open or removed for installation of the gas
fireplace insert.
Smoke shelves, shields and baffles may be removed
if attached by mechanical fasteners. If any part is
removed it must not weaken the structural integrity
of the factory built fireplace.
The fireplace and fireplace chimney must be clean
and in good working order and constructed of non-
combustible materials.
The surround panels should not seal ventilation
openings on the fireplace.
Chimney clean outs should fit properly.
NOTE: Any alterations made to the listed solid fuel
burning factory built fireplace may void the listing
of the fireplace.
Cutting any sheet metal part of the fireplace, in
which the gas fireplace insert is to be installed is
prohibited.
*Check with your local inspector before commencing
with this installation.
Installer must mechanically attach the supplied
label to the inside of the firebox of the fireplace into
which the gas fireplace insert is installed.
"WARNING: This fireplace has been converted
for use with a gas fireplace insert only and
cannot be used for burning wood or solid fuels
unless all original parts have been replaced,
and the fireplace re-approved by the authority
having jurisdiction."
FACTORY-BUILT (METAL) WOOD-
BURNING FIREPLACE
REQUIREMENTS
NOTE: Any parts that are removed must be removed
in a way that would allow them to be re-installed if
the insert is ever removed (removal of rivets or
screws is acceptable).
To reference parts—see illustration below.
Must be removed:
1 -Damper
2- Grate (with log set)
May be removed (if applicable):
3- Smoke shelf
4- Internal baffles
5 - Screen
6 & 7 - Masonry lining or refractory
8 - Metal or glass doors
The fireplace must be permanently marked to
indicate that it has been altered and is no longer
suitable for burning solid fuel (wood), unless the
removed parts are re-installed. Cutting of any sheet
metal parts is prohibited.
May be removed (in certain cases):
9 -Metal floor of the firebox
10 - The insulation and any structured rigid frame
members must not be removed or altered (side and
top of door frame, side and top of the face of the
fireplace, metal sides, etc.).
If the factory-built fireplace has no gas access
hole(s) provided, an access hole of 1.5 inch (37.5
mm) or less may be drilled through the lower sides
or bottom of the firebox in a proper workmanship
like manner. This access hole must be plugged
with non-combustible insulation after the gas
supply line has been installed.
CAUTION:
Firebox floor removal is not covered under the
appliance safety standard (ANSI Z21.88, CSA
2.33) used in the safety certification of this ap-
pliance. The Intertek safety certification does
not apply to this method of installation. Before
installing the appliance using this method, contact
the Authority Having Jurisdiction to determine
if this installation is acceptable in your area.
The sheet metal base of the fireplace must be
left in place and a minimum 1/2" cement board
sheet placed under the entire length and width
of the appliance.
WARNING: Failure to position the parts
in accordance with the diagrams in this
manual or failure to use only parts specifi-
cally approved with this appliance may re-
sult in property damage or personal injury.
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 11
| 11
installation
A
B
C
MATERIALS REQUIRED
A 120 Volt AC power cord is hooked up to operate the fan and operate the gas valve when batteries are
not installed in the receiver. Plug the 3 wire cord into a suitable receptacle. Do not cut the ground
terminal off under any circumstances. When connected with 120 volts, the appliance must be
electrically grounded in accordance with local codes, current version of CSA C22.1 (in Canada) or in
the absence of local codes, with the National Electrical Code ANSI/NFPA 70-1987.
INSTALLATION
CHECKLIST
Before installing vent system ensure that the damper
plate is open and secure to prevent the damper plate
from falling down and crushing the liner.
The Regency Gas Insert is installed as listed.
1. Check all clearances to combustibles, (Refer to
sections "Minimum Fireplace Dimensions and
Clearances to Combustibles)
2. Make the gas connection. (Refer to section "Gas
Connection")
3. Install the two liners (2" intake and 3" exhaust)
to the sliding connector plate. (Refer to section
"Flue Liner Installation.")
4. Slide the unit half way into the fireplace.
5. Pull the vent connector plate through the tapered
brackets and fasten to the front plate. Refer to
section "Flue Liner Installation."
6. Slide the unit fully into the fireplace. Level if
necessary.
7. Hook up 120 volt AC power cord into a suitable
receptacle. Optional: Install 4 batteries in the
battery pack. Batteries only serve as back up
if power is lost within the home.
8. Test gas pressure (Refer to section "Gas Pipe
Pressure Testing"). Check aeration system
(Refer to section "Gas Insert Aeration System").
9. Install standard and optional features. Refer to
the following sections:
a. Brick Panels (LRI3E) or
Enamel Panels (LRI3E,HRI3E)
NOTE: Painted panels come with HRI3E.
(Panels - must be installed to operate unit)
b. Log Set
c. Glass Crystals
d. Spa stones
e Vignette Faceplate
f. Mantel deflector
g. Hearth Trim
h. Backing plate/4 sided backing plate
10. Final check: Before leaving this unit with the
customer, the installer must ensure that the
appliance is firing correctly. This includes:
a) Clocking the appliance to ensure the correct
firing rate.
b) Adjusting the primary air, if required, to
ensure that the flame does not carbon. See
"Gas Insert Aeration System" section.
c) Ensuring that the appliance is venting
correctly.
MINIMUM FIREPLACE DIMENSIONS
The minimum fireplace clearances & dimensions for the Regency gas insert are shown in the following
diagrams:
Max Lintel Bar
Depth
A
Height
B
Depth
C
Width
(rear)
D
Width
(front)
E
Width
F
Front Depth
To Taper
G
Vignette
Faceplate
8-5/8" 19-1/2" 14-1/2" 21-5/8" 28-1/2" 31-1/8" 4"
All manuals and user guides at all-guides.com
all-guides.com

12 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
12 installation
Diagram 1
Diagram3
Diagram 2
Note: A3-1/2"manteldeectortoreduce
mantelheightto28"frombottomof
unit@1"depth.
MINIMUM CLEARANCES TO COMBUSTIBLES
The clearances listed below are Minimum distances unless otherwise stated:
A major cause of fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
decorative gas appliance be installed only in accordance with these instructions.
Clearance: Dimension MeasuredFrom:
A: Sides 6" / 152 mm From inside edge of faceplate / doors
B: Ceiling 60" / 1524 mm From Base of Unit
C: Mantel (Min. Height) *28" / 711mm
38"/ 965mm
From Base of Unit
From Base of Unit
D:Min. Hearth Depth 12" / 305mm Not required if unit raised 3-1/2" off floor
E: Min. Hearth Length 36"/ 914mm
G: Max. Mantle Depth 0-12" / 305 mm @ 47" (1193mm) from bottom of unit
without deflector @12" (305mm) deep
@ 37" (940mm) from bottom of unit with
3-1/2" deflector @12" (305mm) deep
K: Min. Alcove Width 54" / 1372 mm
L: Max. Alcove Depth 36" / 914 mm
M: Mantel Deflector 3-1/2"/ 89mm
NOTE: 36” (914 mm) wide x 12” (305mm) deep non combustible hearth is required in front
of the appliance, unless the unit is raised 3-1/2” (89 mm) off the floor surface.
*An optional 3-1/2" deflector, reduces the mantel height to 28" from bottom of unit
@ 1"depth.
A
C
B
E
K
D
L
G
Mantel Clearances
2
0
12 64
810
0
24
12
16
20
12" (305mm)
1" (25mm)
19" (483mm)
19"(483mm)
to base of unit Side View
32
28
4
8
28" (711mm)
Top of fireplace
opening
Non Combustible
Mantel Clearances
2
0
12 64
810
0
24
12
16
20 12" (305mm)
1" (25mm)
9" (229mm)
19"(483mm)
to base of unit Side View
32
28
Non Combustible
4
818" (457mm) Deflector
Top of fireplace
opening
MANTEL CLEARANCES WITHOUT DEFLECTOR MANTEL CLEARANCES WITH 3-1/2" DEFLECTOR
WARNING
Although this appliance passes safety
certification, the hearth in front of the fireplace
becomes very hot when the fireplace heats. Do
not use the hearth as a seat or shelf.
A noncombustible mantel may be
installed at a lower height
if the framing is made of
metal studs covered with a
noncombustibleboard.
Note: All material used must be
completelynon-combustible.
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 13
| 13
installation
GAS CONNECTION
1. If the appliance is to be installed into an existing
chimney system, thoroughly clean the masonry
or factory built fireplace.
2. The appliance is provided with an opening on
the left hand side of the control compartment.
A 3/8" NPT gas supply pipe must be brought
near this inlet hole.
3. Locate the center point where the vent will pass
through the chimney above the appliance. Move
the appliance into the exact location where it is
to be installed. Ensure that the Insert is level.
4. Do not cut any sheet-metal parts of the fire-
place, in which the gas fireplace insert is to
be installed.
5. If the factory-built fireplace has no gas access
hole(s) provided, an access hole of 1-1/2"
(37.5mm) or less may be drilled though the
lower sides or bottom of the firebox in a
proper workmanship like manner. This access
hole must be plugged with a non-combustible
insulation after the gas supply line has been
installed.
GAS CONNECTION WARNING:
Onlypersonslicensedtoworkwith
gaspipingmaymakethenecessary
gas connections
tothisappliance.
Gas & Electrical Connections
Minimum 8 ft. (2.44m)
Maximum 35 ft. (10.67m)
Exhaust
Flue
2” Liner 3” Liner
3” Collar
Flashing
FPI Co-linear DV
Vertical Termination Cap
Full continuous length
(unit to cap) is required
for both intake & exhaust.
The LRI3E/HRI3E are also approved for use with a 2" liner for air intake and
a 3" liner for exhaust. This would be suitable for a Class A wood burning
chimney with a minimum 6" round flue.
The chimney must be lined with one 2" diameter liner for intake and one 3"
diameter liner for exhaust. The minimum vent length is 8' and maximum is 35'.
The Air Intake pipe must be attached to the inlet air collar of the termination
cap. Periodically check that the vent is unrestricted.
INSTALLATION WITH 3" & 2" LINERS
Part # Description
948-305 3" Flex - 35 ft. (exhaust)
948-316 2" Flex - 35 ft. (intake)
946-582 Regency Co-linear DV Vertical Termination Cap, Flashing &
2" Collar
VentRun Vent Restrictor Position
Up to 8' Position 1
Beyond 8' No restrictor
NOTE: See instructions in the "Vent Restrictor Position" section on
positioning of the vent restrictor.
THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY
FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will
accommodate. However, keep the flexible liner as straight as possible,
avoid unnecessary bending.
All manuals and user guides at all-guides.com

14 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
14 installation
Remove connector plate guide
Vent restrictor install
The LRI3E / HRI3E use a heat exchanger and efficient combustion technol-
ogy to provide extreme heating efficiencies. The more efficient an appliance
becomes, the lower the flue gas temperatures becomes.
On start-up, flue temperatures are required to initiate venting action.
Here are some considerations when setting up the LRI3E / HRI3E:
When operating the unit in temperatures below 50° F, run the pilot in "Standing
Pilot" mode, 1. Press and hold the small flame icon on the hand held remote
control to set the appliance at continuous pilot.
Note: If after 5 days the appliance has not had a call for heat, the pilot will
extinguish and will not be present. To enable pilot operation you will need to
repeat steps for continuous pilot operation.
STANDING PILOT
ALTERNATE APPROVED CAPS/ADAPTOR
tooltip
Flue connector
plate guide
tooltip
Restrictor
plate
Note: only installed on runs at the minimum 8 feet vent height from above unit.
If longer than 8 feet the restrictor is not required.
1. Remove flue connecter plate by sliding out toward the back of the unit - see
next page.
VENT RESTRICTOR PLATE INSTALLATION
46DVA-GK 3" Co-linear Adaptor with flashing
46DVA-VC Vertical Termination Cap
or
46DVA-VCH High Wind Cap
* 948-417/P 2” to 3” Increaser (Air inlet)
*Note : The 46DVA-GK Co-linear Adaptor with flashing comes with 2 - 3”
collars. The increaser is required to adapt the flex (air inlet side) which is 2
inch to the 46DVA-GK Co-linear Adaptor with flashing.
In areas of consistently high winds, we recommend using the Simpson
Dura-Vent System (46DVA-GK adapter and 46DVA-VCH high-wind cap). The
Air Intake pipe must be attached to the inlet air collar of the termination cap.
This chimney system is also ideal when the chimney termination is round in
applications where this appliance is being installed into a factory built fireplace.
2. Remove left flue connector plate guide by removing 2 screws as shown below.
3. Flip the flue connector plate gasket to the right (out of the way) to allow ease
of installation of the vent restrictor.
4. Install vent restrictor with 2 screws in location shown above.
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 15
| 15
installation
1. Detach the Flue Connector Plate from the unit by removing the
Connector Plate Screws and sliding the Flue Connector Plate forward
and off the unit.
NOTE: Flue Plate Connector Gasket
must not be damaged or removed.
Care must be taken to ensure that this
gasket remains intact to prevent flue
leakage.
5. When the Flue Connector Plate is close to the front of the unit, engage
the Flue Connector Screws and carefully tighten the Flue Connector
Plate the final amount.
** Make sure the Rear Tab connects into the slot in the Flue Connector
Plate. Failure to do so will result in flue gas leakage and degrade the
operation of the unit ** (See diagram below of location.)
The Flue connection is complete when the Flue Connector Plate is fully
forward and the Rear Tabs are fully engaged.
6. Remove the Flue Connector Tool and store for future use.
2. Attach the Flue Liners onto the Flue Connector Plate using non RTV
type sealant, then fasten with 3 screws.
See the section in this manual on Venting installation.
3. Position the unit in front of the fireplace opening, start the Flue Connec-
tor Plate into the Flue Connector Plate Guides.
Flue Connector Slide Tool
Tab connected correctly
Flue Connector Plate
Connector plate screws
4. Use the Flue Connector Slide Tool to slowly pull the Flue Connector Plate
forward as you move the Insert rearward into the Fireplace Chase.
FLUE / VENT INSTALLATION
WARNING:
Failure to position the parts in accordance with these diagrams or failure
to use only parts specifically approved with this appliance may result in
property damage or personal injury.
Connecting the Vent Liners
Intake Liner
Exhaust Liner
ue connecter
plate
All manuals and user guides at all-guides.com

16 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
16 installation
The burner aeration is factory set but may need adjusting due to either the
local gas supply or altitude.
Air Shutters are required to increase or decrease the amount of air that is
mixed with the fuel before combustion. This will have an affect on how well
the fuel combusts and how the flame appears physically.
Low primary air will leave a taller, yellower flame while higher primary air will
leave a lower, bluer flame.
This setting is largely for appearance, however, not enough primary air may
lead to carboning, sooting or a flame that reaches the top of the firebox.
Situations that may require more primary air are; units that are burning
propane, units installed at higher elevations or units that are run on high
most of the time.
Unit Fuel Type Min. Air Setting
LRI3E NG 1/8" (3mm)
LRI3E LP 1/4" (6mm)
HRI3E NG 1/8" (3mm)
HRI3E LP 5/16" (8mm)
NOTE: In higher elevations, air shutter settings may have to be opened
more to compensate.
The minimum air settings noted for the HRI3 are good for both media and
driftwood log set.
AIR SHUTTER ADJUSTMENT
CAUTION: Carbon will be produced if air shutter is closed too much.
Note: any damage due to carboning resulting from improperly setting
the aeration controls is NOT covered under warranty.
Note: AerationAdjustmentshouldonlybeperformedbyanauthorized
RegencyInstalleratthetimeofinstallationorservice.
First Fire & Aeration
LRI3E
Screw to adjust aeration
LRI3E- Remove the burner by removing 2 screws in locations shown below.
Slide burner to the left and lift out to remove.
tooltip
HRI3E
burner cover
burner
HRI3E - Remove the burner by removing 5 screws in locations shown below
to remove burner cover and 2 screws to remove burner (shown below). Slide
burner to the left to remove.
tooltip
All manuals and user guides at all-guides.com
all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 17
| 17
installation
WIRING DIAGRAM -- SYSTEM WITH FAN (LRI3E / HRI3E)
CAUTION:Labelallwirespriortodisconnection
whenservicingcontrols.Wiringerrorscancause
improperanddangerousoperation.
Caution:Ensurethatthewiresdonottouchany
hotsurfacesandareawayfromsharpedges.
If any of the original wire as supplied with the appliance must be replaced, it must be replaced with type CPE wire or its equivalent.
IMPORTANT: The 120V fan control module serves as the power source for this unit. The AA batteries in the battery holder are recommended as a backup in
case 120 volt power is lost within the home.
All manuals and user guides at all-guides.com

18 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
18 installation
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut-off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa). Disconnect
piping from valve at pressures over 1/2 psig.
The manifold pressure is controlled by a regulator
HIGH ELEVATION
This unit is approved for altitude 0 to 4500 ft. (CSA
2.17-2017).
GAS LINE
INSTALLATION
Since some municipalities have additional local
codes it is always best to consult with your local
authorities and the CAN/CGA B149 installation
code.
For USA installations follow local codes and/or the
current National Fuel Gas Code, ANSI Z223.1.
When using copper or flex connectors use only
approved fittings. Always provide a union so that
gas lines can be easily disconnected for servicing.
Flare nuts for copper lines and flex connectors are
usually considered to meet this requirement.
NOTE: A shutoff / dante valve should be sup-
plied in or near the unit (or as per local codes)
for ease of servicing this appliance.
IMPORTANT: Always check for gas leaks with
a soap and water solution or gas leak detector.
Do not use open flame for leak testing.
LRI3E-NG1 SYSTEM DATA
Min. Supply Pressure 5" WC (1.25 kpa)
Max. Supply Pressure 1/2" Psi (3.45 kpa)
Manifold Pressure - High 3.5" WC (0.87 kpa)
Manifold Pressure - Low 1.6" WC (0.40 kPa)
Orice Size #45 DMS
Maximum Input 20,500 Btu/h (6.0 kW)
Minimum Input 14,000 Btu/h (4.10 kW)
LRI3E-LP1 SYSTEM DATA
Min. Supply Pressure 11" WC (2.73 kpa)
Max. Supply Pressure 1/2" Psi (3.45 kpa)
Manifold Pressure-High 10" WC (2.49 kpa)
Manifold Pressure-Low 6.4" WC (1.60 kpa)
Orice Size #55 DMS
Maximum Input 19,000 Btu/h (5.57 kW)
Minimum Input 15,500 Btu/h (4.54 kW)
Note: Ifyouhaveanincorrectamepattern,
contactyourRegency®dealerforfurther
instructions.
Incorrect flame pattern will have small,probably
yellow flames, not coming into proper contact
with the rear burner or flame sensor.
Burner
Flame Sensor
Pilot Ignitor
PILOT ADJUSTMENT
Periodically check the pilot flames.Correct flame
pattern has two strong blue flames: 1 flowing
around the flame sensor and 1 flowing across
the burner (it does not have to be touching the
burner).
885 S.I.T. VALVE
DESCRIPTION
1) 6 Stage flame adjustment
2) Pilot adjustment
3) Outlet Pressure Tap
4) Inlet Pressure Tap
5) Pilot Outlet
6) Main Gas Outlet
7) Main Gas Inlet
1
2
3
4
6
5
7
HRI3E-NG1 SYSTEM DATA
Min. Supply Pressure 5" WC (1.25 kpa)
Max. Supply Pressure 1/2" Psi (3.45 kpa)
Manifold Pressure - High 3.5" WC (0.87 kpa)
Manifold Pressure - Low 1.6" WC (0.40 kPa)
Orice Size #45 DMS
Maximum Input 19,500 Btu/h (5.71 kW)
Minimum Input 14,000 Btu/h (4.10 kW)
HRI3E-LP1 SYSTEM DATA
Min. Supply Pressure 11" WC (2.73 kpa)
Max. Supply Pressure 1/2" Psi (3.45 kpa)
Manifold Pressure-High 10" WC (2.49 kpa)
Manifold Pressure-Low 6.4" WC (1.60 kpa)
Orice Size #55 DMS
Maximum Input 19,500 Btu/h (5.71 kW)
Minimum Input 14,000 Btu/h (4.10 kW)
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure, both
inletandmanifoldpressuresshouldbe
checkedusingthevalvepressureports
onthevalve.
1. Make sure the unit is in the "OFF" position.
2. Loosen the "IN" and/or "OUT" pressure tap(s),
turning counterclockwise with a
1/8" wide flat screwdriver.
3. Attach manometer to "IN" and/or "OUT" pressure
tap(s) using a 5/16" ID hose.
4. Turn the unit on with the remote or wall switch
5. The pressure check should be carried out with
the unit burning and the setting should be within
the limits specified on the safety label.
6. When finished reading manometer, turn off
the unit, disconnect the hose and tighten the
screw (clockwise) with a 1/8" flat screwdriver.
Note:Screw should be snug, but do not over
tighten.
All manuals and user guides at all-guides.com

LRI3E-1 / HRI3E-1 Direct Vent Gas Insert | 19
| 19
installation
919-827 01.25.18
1
LRI3E / HRI3E
CONVERSION FROM NG TO LP
LRI3E/HRI3E
This conversion should be done before the unit is initially installed:
If installed already, the draft hood assembly will need to be removed
so appliance may be slid out from the fireplace opening for ease of
conversion. See manual for details
Before you begin:
Shut off the gas supply to the unit.
Disconnect all electrical supply to the unit.
Always let the appliance cool to room temperature before servicing.
1. Remove faceplate, glass door , inner panels, glass crystals, media, logs
(if already installed)—see instructions in the manual.
2. Slide unit out and remove 3 front screws and loosen 2 back screws to
remove the left side control cover.
3. Disconnect the cable coming from the pressure regulator motor.
WARNING
This conversion kit shall be installed by a qualified service agency in ac-
cordance with the manufacturer’s instructions and all applicable codes and
requirements of the authority having jurisdiction. If these instructions is not
followed exactly, a fi re, explosion or production of carbon monoxide may
result causing property damage, personal injury or loss of life. The quali-
fi ed service agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the operation of the converted
appliance is checked as specified in the manufacturer’s instructions sup-
plied with the kit.
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER
IF IN DOUBT DO NOT DO THIS CONVERSION!
LRI3E
Conversion Kit includes:
1 904-575 Burner Orifice #55
1 910-101 Pilot Orifice #35
1 908-590 Decal - Conversion to LP
1 911-011 Stepper Motor - LP
1 904-529 5/32" long Allen Key
1 908-528 Label Propane Red
6. Reattach the pressure regulator wire.
7. LRI3E- Remove the burner by removing 2 screws in locations shown below.
HRI3E- See next page.
Side control cover
5
HPRYH
/RRVHQ
4. Remove and discard 2 Pressure regulator screws A (T20 or slot), Pres-
sure Regulator B, Spring and Diaphragm C.
5. Ensure the rubber gasket, which is prefitted as part of the Assembly,
is properly positioned. Install the new Pressure Regulator using the 2x
M4 x .7 screws supplied. Tighten the screws to 25lb-in. In the event that
the screw threads are cross threaded or stripped, replace the valve as-
sembly.
Install the enclosed propane identification label to the valve body where it
can be easily seen.
CONVERSION FROM NG TO LP
LRI3E/HRI3E USING PROFLAME 885 VALVE
All manuals and user guides at all-guides.com

20 | LRI3E-1 / HRI3E-1 Direct Vent Gas Insert
|
20 installation
919-827 01.25.18
2
LRI3E / HRI3E
12. Attach the label “This unit has been converted to LPG” near or on top of
the serial # decal.
13. Replace yellow “NG” label with red “LPG” label.
14. Adjust aerations settings:
LRI3E = 1/4" (6 mm)
HRI3E = 5/16" (8 mm)
NOTE: In higher elevations, air shutter settings may have to be opened
more to compensate.
The minimum air settings noted for the HRI3E are good for both media and
driftwood log set.
15. Reinstall burner removed in Step 7.
16. Check for gas leaks.
17.Check inlet and outlet pressures. See Gas Pipe PressureTesting in manual.
18. Reverse steps 2-1 to reassemble unit.
19. Check operation of fl ame control.
Installer Notice:
These instructions must be left
with the appliance.
10. Remove burner orifice with a 1/2" wrench. Use another wrench to hold
onto the elbow behind the orifice. Recycle orifice.
11. Reinstall new burner orifice LPG stamped #55 and tighten.
Burner orifi ce
8. From inside the fi rebox, remove pilot retainer clip with pliers and pull off the
pilot cap to expose the pilot orifice.
HRI3E
HRI3E - Remove the burner by removing 5 screws in locations shown below
to remove burner cover and 2 screws to remove burner (shown below).
burner cover
burner
9. Unscrew the pilot orifice with the Allen key; then replace with the LPG
pilot orifice and the pilot cap, provided in the kit.
Pilot retainer clip
All manuals and user guides at all-guides.com