Regency Fireplace Products Liberty LRI3E Quick start guide

Liberty®LRI3E / Regency Horizon®HRI3E
Gas Insert
Owners &
Installation Manual
www.regency-fire.com
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach your gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
MODELS: LRI3E-NG11 Natural Gas LRI3E-LP11 Propane
HRI3E-NG11 Natural Gas HRI3E-LP11 Propane
919-996e FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 10.14.21
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
Tested by:
Certified to/Certifié pour: CSA 2.17-2017
ANSI Z21.88-2017
CSA 2.33-2017

2 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
TO THE NEW OWNER
Congratulations! You are the owner of a state-of-the-art Gas Insert by Regency.
The Regency Gas Insert Series of hand crafted appliances has been designed to provide you with all the warmth
and charm of a fireplace, at the flick of a switch. The models LRI3E-11 / HRI3E-11 of this series have been approved
by Warnock Hersey/Intertek for both safety and efficiency. As it also bears our own mark, it promises to provide you
with economy, comfort and security for many trouble free years to follow.
Please take a moment now to acquaint yourself with these instructions and the many features of your
Regency Fireplace.
This product may be installed in an aftermarket, perma-
nently located,manufacture home (USA only) or mobile
home, where not prohibited by local codes.
This appliance is only for use with the type of gas
indicated on the rating plate. This appliance is not
convertible for use with other gases, unless a certified
kit is used.
920-408
4.34.7
Instruction Plate
For a glass-fronted gas appliance where the temperature of the glass
viewing area outside surface exceeds the limits specified in Clause 5.14.4, the following
graphic danger and statements shall be shown on a Class IIIA-2 Permanent Label.
4.34.6
Instruction Plate
Each appliance shall bear a Class IIIB marking with letters on a contrasting background, located
adjacent to the controlling device or in an equally conspicuous position where the instruction can be easily read.
April 22/14: Created draft
Double sided
Material: Synthetic Paper
Size 5.965" W x 5.71" H
Color: As shown in artwork
DANGER
HOT GLASS WILL
CAUSE BURNS
DO NOT TOUCH GLASS
UNTIL COOLED
NEVER ALLOW CHILDREN
TO TOUCH GLASS
A barrier designed to reduce the risk of burns from the hot viewing glass
is provided with this appliance and must be installed for the protection
of children and other at risk individuals.
!DANGER
!
920-408
CAUTION:
HOT WHILE IN OPERATION. DO NOT TOUCH.
SEVERE BURNS MAY RESULT. KEEP CHILDREN, CLOTHING, FURNITURE,
GASOLINE, AND ANY OTHER LIQUIDS WITH FLAMMABLE VAPOURS AWAY.
KEEP BURNER AND CONTROL COMPARTMENT CLEAN.
SEE INSTALLATION AND OPERATING INSTRUCTIONS ACCOMPANYING
APPLIANCE.
Front Back
LA SURFACE VITRÉE CHAUDE
PEUT CAUSER DES BRÛLURES.
NE TOUCHEZ PAS À LA
SURFACE VITRÉE NON REFROIDIE.
NE LAISSEZ JAMAIS UN
ENFANT TOUCHER LA SURFACE
VITRÉE.
DANGER
!
L’écran pare-étincelles fourni avec ce foyer réduit le risque de brûlure en cas de
contact accidentel avec la vitre chaude et doit être installé pour la protection des
enfants et des personnes à risque.
920-408-fr
ATTENTION
S'assurer que le brûleur et le compartiment des commandes sont propres.
Voir les instructions d’installation et d’utilisation qui accompagnent
l'appareil.
Risque de brûlures graves.
Ne pas toucher l’appareil lorsqu’il fonctionne.
Ne pas laisser les enfants s’approcher de l’appareil. Garder les
vêtements, les meubles et tout gaz ou liquide inflammable (carburant)
à distance de l'appareil.

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 3
table of contents
Requirements ..............................................................17
Installation Checklist ....................................................18
Materials Required ......................................................18
Minimum Fireplace Dimensions ..................................18
Minimum Clearances to Combustibles ........................19
Gas Connection ...........................................................20
Alternate Approved Caps/Adaptor ...............................21
Standing Pilot .............................................................21
Vent Restrictor Plate Installation ..................................21
Flue / Vent Installation .................................................22
Air Shutter Adjustment .................................................23
Wiring Diagram with fan (LRI3E-11 / HRI3E-11) .........24
System Data ................................................................25
High Elevation ..............................................................25
Gas Line Installation ....................................................25
Pilot Adjustment ...........................................................25
Gas Pipe Pressure Testing ..........................................25
885 S.I.T. Valve Description .........................................25
Conversion from NG to LP .........................................26
Media Installation .........................................................28
HRI3E-11 Optional Log Set Installation .......................29
LRI3E-11 Log Set Installation .....................................31
Brick Panel Installation ................................................33
Painted Black and Enamel Panel Installation ..............34
Glass Door Removal / Installation ...............................35
Vignette Faceplate with Safety Screen Installation ......36
Inlay Installation ...........................................................37
Backing Plate Installation ............................................39
Optional Arched Vignette Faceplate Installation ..........40
Optional Backing Plate Installation ..............................41
Optional Hearth Trim Installation .................................42
Optional Mantel Deflector Installation ..........................42
Operating Instructions
First Fire ......................................................................43
Operating Instructions .................................................43
Maintenance
Normal Operating Sounds of Gas Appliances .............44
Maintenance Instructions ............................................44
Door Glass ..................................................................45
Glass Replacement .....................................................45
Pilot Adjustment ...........................................................46
General Vent Maintenance ..........................................46
Log Replacement ........................................................46
Glass Gasket ...............................................................46
Backup Battery Pack ...................................................46
Fan Replacement - with Remote Control .....................47
Valve Replacement ......................................................48
Gas Maintenance ........................................................50
Parts
LRI3E-11 Parts List .....................................................51
LRI3E-11 Main Assembly ............................................52
HRI3E-11 Parts List .....................................................53
HRI3E-11 Main Assembly ...........................................54
Accessories .................................................................55
Warranty .....................................................................56
Dimensions
Unit dimensions with Vignette Faceplate .......................4
Unit dimensions with Vignette Faceplate + Small Back-
ing Plate .........................................................................4
Unit dimensions with 4 sided Vignette Faceplate + Back-
ing Plate .........................................................................5
Unit Dimensions with Arched Vignette Faceplate ..........6
Unit Dimensions with Arched Vignette Faceplate +
Backing Plate .................................................................6
Installation
Gas Pressure Testing ..................................................17
Installation Into A Solid Fuel Burning Fireplace or Fac-
tory Built Fireplace .......................................................17
Factory-Built (Metal) Wood-Burning Fireplace
On Demand Pilot (seven day safety timer)
Important information if using the appliance in CPI (continuous pilot
mode) only
This appliance is a ProFlame 2 system fitted with the “On Demand” Pilot, a
safety feature which will shut down the gas valve completely by extinguishing
the pilot light in the event of a continuous full seven days of inactivity.
This only applies if the CPI (continuous pilot) switch is in the “on” position in
your remote control transmitter.
Each time the main burner shuts down, manually or through the call from the
thermostat, the seven day timer starts again.
The seven day inactivity timer is controlled within the circuit board. Therefore,
if in CPI mode and when the pilot light is extinguished after seven straight
days of inactivity, the CPI setting on the remote control transmitter will remain
in the “CPI” (continuous pilot) position. Therefore, all that is required to relight
the pilot would be to press the on/off button on the remote control transmitter
from “on” to “off” and back to “on”. Once the pilot has re-established operation
will resume as normal. There is no requirement to do anything with the IPI/CPI
mode on the remote control transmitter.
If the unit never goes as long as seven full days without a call for heat, the pilot
will remain lit until it is manually shut-off.
If the unit is being operated in IPI (intermittent pilot) mode, neither the above
instructions nor the seven day timer will apply.
See the instructions in this manual and on the Lighting Instructions plate on
the appliance to light or re-light the pilot.
OWNER’S INFORMATION
Copy of Safety Label HRI3E-11 / ..................................7
Copy of Safety Label LRI3E-11 .....................................8
MA Code - CO Detector ................................................9
Important Message ......................................................10
Before You Start ...........................................................10
Important Message ....................................................10
For Your Safety ............................................................10
Specifications ..............................................................10
Lighting Procedure ......................................................11
Shutdown Procedure ...................................................11
Copy Of Lighting Instruction Plate ...............................12
Proflame II Remote Control Operating Instructions .....13
Warranty .....................................................................56
INSTALLER’S INFORMATION

4 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
dimensions
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE
UNIT DIMENSIONS WITH VIGNETTE FACEPLATE + SMALL BACKING PLATE
10-3/8”
29-1/16"
22-3/4"
22-1/2"
26"
19”
28"
14"
21-5/16"
1-13/16”
(711mm)
(540mm)
(355mm)
(738mm)
(660mm)
(572mm)
(576mm)
(45mm)
(262mm)
(482mm)
10-3/8"
(262mm)
(482mm)
19"
738mm
29-1/16”
794mm
31-1/4”
23 -3/8” 593 mm
14
-1/4”
36 2mm
22-11/16”
576mm
21-5/16”
540mm
711mm
28”
1-7/8”
47mm
Not Shown:
Regular backing plate - 35-3/4" W x 25-5/8" H
Oversize backing plate - 38-3/16" W x 29-5/8" H

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 5
dimensions
UNIT DIMENSIONS WITH 4 SIDED VIGNETTE FACEPLATE + BACKING PLATE
28-5/8”
726mm
29-1/4”
743mm
35-3/4”
908mm
28”
711mm
21-5/16”
540mm
1-15/16”
48mm
10-3/8”
262mm
3”
76mm
19”
482mm
14”
355mm
3”
76mm
ALL PICTURES / DIAGRAMS SHOWN THROUGHOUT THIS MANUAL ARE FOR ILLUSTRATION PURPOSES ONLY.
ACTUAL PRODUCT MAY VARY DUE TO PRODUCT ENHANCEMENTS.

6 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
dimensions
UNIT DIMENSIONS WITH ARCHED VIGNETTE FACEPLATE
UNIT DIMENSIONS WITH ARCHED VIGNETTE FACEPLATE + BACKING PLATE
25 3
16
"
35 15
16
"
22 11
16
"
15 15
16
"
32 13
16
"
2"
27 11
16
"
40 15
16
"
24 1
2
"
15 15
16
"
32 13
16
"
2 1
8
"

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 7
dimensions
This is a copy of the labels that accompany each HRI3E-11 Gas Insert.
We have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a difference, the label on the unit is the correct one.
NATURAL GAS FIREPLACE INSERT: MODEL HRI3E-NG11
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 5" WC (1.25 kpa)
Low Setting Man. pressure 1.6" WC (0.40 kpa)
Max. Manifold pressure 3.5" WC (0.87 kpa)
Orifice size #45 DMS
Minimum input 14,000 Btu/h (4.10 kW)
Maximum input 19,500 Btu/h (5.71 kW)
PROPANE GAS FIREPLACE INSERT: MODEL HRI3E-LP11
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 11" WC (2.73 kpa)
Low Setting Man. pressure 6.4" WC (1.59 kpa)
Max. Manifold pressure 10" WC (2.49 kpa)
Orifice size #55 DMS
Minimum input 15,500 Btu/h (4.54 kW)
Maximum input 19,000 Btu/h (5.57 kW)
Model/Modèle: HRI3E-NG11
919-949a
Part #: 919-949a
Colour: Black on grey except what is highlighted is printed red
Size: (File at 100%) 6.495"W x 8.66" H
Material: 2 ml silver matt polyester (DPM SMS)
Oct 30/2018: Created draft
Nov.05/2018 : New Serial #
Dec. 14/18: Added efficiencies
Jan 23/19: Rev A - Remodeled decal + added ETL logo at the bottom
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ÉTIQUETTE
Serial No. / No de série
487
487
Duplicate Serial number/Copie No de série
Listed: VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION
Certified to/Certifi pour : éCSA 2.17-2017
ANSI Z21.88-2017
CSA 2.33-2017
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE.
Model/Modèle: HRI3E- LP11
ENCASTRABLE AU GAZ PROPANE
MODÈLE HRI3E-LP11
ENCASTRABLE AU GAZ NATUREL
MODÈLE HRI3E-NG11
Pression d'alimentation minimale
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimalé
D bit calorifique maximalé
Min. Hearth Depth/
Prof. min. âtre D 12” (305mm)
Min. Hearth Width/
Largeur min. âtre E 36” (914mm)
Max. Mantle Depth/
Prof. max. manteau G 12" (305mm)
Mantel Clearances / Dégagements manteau
FPI Fireplace Products International, Ltd
Delta BC, CANADA
Side wall /mur latéral A 6” (152mm)
Ceiling/Plafond B 60” (1524mm)
Mantel/Manteau C 38” (965mm)
Min. Alcove Width/
Largeur min. alcôve K 54" (1372mm)
Max. Alcove Depth/
Prof. max. alcôve L 36” (914mm)
MADE IN CANADA /FABRIQUÉ AU CANADA
Minimum Clearances to Combustibles
from Insert/Dégagements min. combustibles
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases unless a certified kit is used.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details
WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Cet appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, conformément au National Fuel Gas
Code ANSI Z223.1, ou au CSA-B149.1 en vigueur.
Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.
AVERTISSEMENT : Ce foyer a été converti pour être utilisé avec un foyer au gaz encastrable et ne peut être utilisé pour brûler du bois ou d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remises en place et que le foyer ait été homologué de nouveau par une autorité
compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à
évacuation.
For use with glass doors certified with the appliance only. Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil.
For use only with barrier (Part # 716-010) Follow installation instructions. Pour utilisation uniquement avec l’écran(Pièce n°716-010)
Suivre les consignes d'installation.
C # 4001172
Pression d'alimentation minimale
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimalé
D bit calorifique maximalé
Electrical supply / Alimentation électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 911-207/Pièce ventilateur
A
C
B
E
K
D
L
G
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1
Natural Gas / Gaz naturel 64.36%
Propane Gas / Gaz propane 66.24%
CANADIAN ENERGY
PERFORMANCE
VERIFIED
RENDEMENT
ÉNERGÉTIQUE
VÉRIFIÉ
EP5011169
For the State of Massachusetts, installation and repair
must be done by a plumber or gasfitter licensed in
the Commonwealth of Massachusetts.
For the State of Massachusetts, flexible connectors
shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances indi-
vidual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation
of a carbon monoxide alarm in accordance with NFPA
720 and a CO alarm with battery back up in the same
room where the gas appliance is installed.
COPY OF SAFETY LABEL HRI3E-11
Remove faceplate from front of unit (see manual)
Once the faceplate is removed the rating plate will
be located below the glass (see picture).
DO NOT REMOVE THE DECAL FROM THE UNIT
DECAL LOCATION

8 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
safety decal
This is a copy of the labels that accompany each LRI3E-11 Gas Insert.
We have printed a copy of the contents here for your review.
NOTE: Regency units are constantly being improved. Check the label on
the unit and if there is a difference, the label on the unit is the correct one.
NATURAL GAS FIREPLACE INSERT: MODEL LRI3E-NG11
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 5" WC (1.37 kpa)
Low Setting Man. pressure 1.6" WC (0.40 kpa)
Max. Manifold pressure 3.5" WC (0.87 kpa)
Orifice size #45 DMS
Minimum input 14,000 Btu/h (4.10 kW)
Maximum input 20,500 Btu/h (6.00 kW)
PROPANE GAS FIREPLACE INSERT: MODEL LRI3E-LP11
Factory Equipped For Altitude 0-4500ft. (0-1370m)
Min. supply pressure 11" WC (2.73 kpa)
Low Setting Man. pressure 6.4" WC (1.59 kpa)
Max. Manifold pressure 10" WC (2.49 kpa)
Orifice size #55 DMS
Minimum input 15,500 Btu/h (4.54 kW)
Maximum input 19,000 Btu/h (5.57 kW)
Model/Modèle: LRI3E-NG11
919-950a
Part #: 919-950a
Colour: Black on grey except what is highlighted is printed red
Size: (File at 100%) 6.503"W x 8.625" H
Material: 2 ml silver matt polyester (DPM SMS)
Oct 30/2018: Created draft
Nov 05/2018: New Serial #
Dec.14/18: Added efficiencies
Jan. 21/19: Remodeled the decal & added ‘’Canadian Energy Performance Verified’’
DO NOT REMOVE THIS LABEL /
NE PAS ENLEVER CETTE ÉTIQUETTE
Serial No. / No de série
488
488
Duplicate Serial number/Copie No de série
VENTED GAS FIREPLACE HEATER - NOT FOR USE WITH SOLID FUELS.
FOYER AU GAZ À ÉVACUATION - NE PAS UTILISER AVEC UN COMBUSTIBLE SOLIDE.
Model/Modèle: LRI3E- LP11
ENCASTRABLE AU GAZ PROPANE
MODÈLE LRI3E-LP11
ENCASTRABLE AU GAZ NATUREL
MODÈLE LRI3E-NG11
Pression d'alimentation minimale
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimalé
D bit calorifique maximalé
Min. Hearth Depth /
Prof. min. âtre D 12” (305mm)
Min. Hearth Width/
Largeur min. âtre E 36” (914mm)
Max. Mantle Depth/
Prof. max. manteau G 12" (305mm)
Mantel Clearances / Dégagements manteau
Side wall /mur latéral A 6” (152mm)
Ceiling/Plafond B 60” (1524mm)
Mantel/Manteau C 38” (965mm)
Min. Alcove Width/
Largeur min. alcôve K 54" (1372mm)
Max. Alcove Depth/
Prof. max. alcôve L 36” (914mm)
MADE IN CANADA /FABRIQUÉ AU CANADA
Minimum Clearances to Combustibles
from Insert/Dégagements min. combustibles
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1, or Natural Gas and
Propane Installation Code, CSA B149.1.
This appliance is only for use with the type of gas indicated on the rating plate.
This appliance is not convertible for use with other gases unless a certified kit is used.
This appliance is only for use with the type of gas indicated on the rating plate and may be installed in an aftermarket, permanently located, manufactured
(mobile) home where not prohibited by local codes. See owner's manual for details
WARNING. This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original
parts have been replaced, and the fireplace re-approved by the authority having jurisdiction.
Cet appareil doit être installé conformément aux codes et règlements locaux, ou, en l'absence de tels règlements, conformément au National Fuel Gas
Code ANSI Z223.1, ou au CSA-B149.1 en vigueur.
Cet appareil doit être utilisé uniquement avec le type de gaz indiqué sur la plaque signalétique. Cet appareil peut être installé dans une maison
préfabriquée ou mobile (É.-U. seulement) installée à demeure si les règlements locaux le permettent. Voir la notice de l'utilisateur pour plus de
renseignements. Cet appareil ne peut pas être utilisé avec d'autres gaz sauf si une trousse de conversion certifiée est fournie.
Cet appareil n'est pas convertible pour une utilisation avec d'autres gaz, sauf si un kit certifié est utilisé.
AVERTISSEMENT : Ce foyer a été converti pour être utilisé avec un foyer au gaz encastrable et ne peut être utilisé pour brûler du bois ou d'autres
combustibles solides à moins que toutes les pièces d'origine aient été remises en place et que le foyer ait été homologué de nouveau par une autorité
compétente.
This vented gas fireplace heater is not for use with air filters. Ne pas utiliser de filtre à air avec ce foyer au gaz à
évacuation.
For use with glass doors certified with the appliance only. Pour utilisation uniquement avec les portes en verre certifiées avec l'appareil.
For use only with barrier (Part # 716-010) Follow installation instructions. Pour utilisation uniquement avec l’écran(Pièce n°716-010)
Suivre les consignes d'installation.
Pression d'alimentation minimale
Pression de sortie (manifold) - basse
Pression de sortie (manifold) - max.
Taille de l'orifice
D bit calorifique minimalé
D bit calorifique maximalé
Electrical supply / Alimentation électrique 115VAC, 2.5 A, 60Hz, Less than 10A Fan Part # 911-207/Pièce ventilateur
A
C
B
E
K
D
L
G
C # 4001172
Listed: VENTED GAS FIREPLACE HEATER/FOYER AU GAZ À ÉVACUATION
Certified to/Certifi pour : éCSA 2.17-2017
ANSI Z21.88-2017
CSA 2.33-2017
Refer to Intertek's Directory of Building Products for detailed information.
Pour plus de détails , se reporter au Répertoire des produits de construction de Intertek.
FPI Fireplace Products International, Ltd
Delta BC, CANADA
CSA P.4.1 Fireplace Efficiency (FE) /Efficacité énergétique des foyers (EEF) CSA P.4.1
Natural Gas / Gaz naturel 66.25%
Propane Gas / Gaz propane 66.70%
CANADIAN ENERGY
PERFORMANCE
VERIFIED
RENDEMENT
ÉNERGÉTIQUE
VÉRIFIÉ
EP5011169
For the State of Massachusetts, installation and repair must be done by a plumber or gas fitter licensed in the Commonwealth of
Massachusetts.
For the State of Massachusetts, flexible connectors shall not exceed 36 inches in length.
For the State of Massachusetts, the appliances individual manual shut-off must be a t-handle type valve.
The State of Massachusetts requires the installation of a carbon monoxide alarm in accordance with NFPA 720 and a CO alarm with
battery back up in the same room where the gas appliance is installed.
COPY OF SAFETY LABEL LRI3E-11

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 9
requirements
installer's information
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a battery operated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)

10 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
owner's information
IMPORTANT MESSAGE
SAVE THESE INSTRUCTIONS
The LRI3E-11 / HRI3E-11 Gas Inserts must be
installed in accordance with these instructions.
Carefully read all the instructions in this manual
first. Consult the "authority having jurisdiction" to
determine the need for a permit prior to starting the
installation. It is the responsibility of the installer to
ensure this fireplace is installed in compliance with
manufacturers instructions and all applicable codes.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are required
by the Canadian Safety Standards and ANSI
Standards to make you aware of the following: CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL, ETC.IT IS IMPERATIVETHAT
CONTROLCOMPARTMENTS,BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
IFTHE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITHTHE MANUFACTURER'S BARRIER
FOR THIS APPLIANCE.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
AN APPLIANCE MUST BE REPLACED
PRIORTOOPERATINGTHE APPLIANCE.
FOR YOUR SAFETY
This appliance requires air for proper combustion.
Always provide adequate combustion and ventilation
air. Follow instructions and information in CAN/CGA
B149 (in Canada) or the National Fuel Gas Code
ANSI Z223.1 (in the USA), regarding requirements
for combustion and ventilation air.
SPECIFICATIONS
At pressures over 1/2 psig, the pipe to the unit must
be disconnected.
Gas Max. Input Capacity:
Natural Gas HRI3E 19,500 Btu/h
LRI3E 20,500 Btu/h
Propane HRI3E 19,000 Btu/h
LRI3E 19,000 Btu/h
Min. Input
Natural Gas HRI3E 14,000 Btu/h
LRI3E 14,000 Btu/h
Propane HRI3E 15,500 Btu/h
LRI3E 15,500 Btu/h
Fuels: Approved for use with both natural gas,
and propane. Approved as is for use at 0' to 4,500'
(0-1370m).
Electrical: 120V A.C. system.
Circulation Fan: Variable speed, 140 CFM.
Log Set: Ceramic fibre, 7 per set - LRI3E
Glass Crystals: 4lbs of glass crystals - HRI3E
Optional Log Set: Ceramic fibre, 5 per set + 4lbs
of glass crystals - HRI3E
Vent System: 2" intake with 3" exhaust.
The efficiency rating of the appliance is a
product thermal efficiency rating determined
under continuous operating conditions and was
determined independent of any installed system.
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The Regency Gas Insert must be installed in
accordance with these instructions. Carefully read
all the instructions in this manual first. Consult the
building authority having jurisdiction to determine
the need for a permit prior to starting the installation.
NOTE: Failure to follow the instructions could cause
a malfunction of the heater which could result in
death, serious bodily injury, and/or property damage.
Failure to follow these instructions may also void
your fire insurance and/or warranty.

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 11
owner's information
LIGHTING PROCEDURE
* Not offered on all models.
IMPORTANT: The remote control system supplied with this appliance has
several options for starting/operating the appliance using the battery
holder and ON/OFF key on the hand held transmitter.
Prior to operating this appliance, please read the remote control operat-
ing instructions (packaged with remote control) to understand how to
operate this remote control system.
1. Ensure the battery holder switch is in the Remote position and / or wall
mounted battery holder (if equipped) is in the <REMOTE> position.
2. Press and release the ON/OFF button on the remote handheld transmit-
ter (see Diagram 1). An audible beep should be heard from the receiver.
If not using the remote, the unit can also be turned on by sliding the
battery holder switch to the <ON> position (if equipped).
Note: The first try for ignition will last approximately 60 seconds. If there is no
flame ignition (rectification) the board will stop sparking for approximately
35 seconds. After wait time , the board will start second try for ignition by
sparking for approximately 60 seconds . If there is still no positive ignition
the board will go into lock out.
The system will need to be reset as follows:
a) Turn the system off by pressing the ON/OFF button on the remote.
b) Wait 5 minutes then repeat from step 2.
SHUTDOWN PROCEDURE
1. Press the ON/OFF button on the remote
2. If service is to be performed- you must disconnect power and shut off gas
to the unit.
ON/OFF Button
Diagram 1
Remote shown in Manual Mode on Hi
3. After approximately 4 seconds the spark ignition system will spark for
60 seconds to light the pilot.
4. The unit will turn on.
Fan Operation: The standard fan can be operated by using the remote control
supplied with this unit. See remote control instructions.
Note: In thermostat mode: When the appliance is turned on, the fan will not
come on for the first 5 minutes (if fan is turned on). When the appliance is
turned off the fan will not turn off for 12 minutes (if in on position)
Manual mode: Fan will turn on and off immediately using the remote control
transmitter if the fan function is in the "on" position.
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
See remote control instructions for details.
*
*
*
On Demand Pilot (seven day safety timer)
Important information if using the appliance in CPI (continuous pilot mode) only
This appliance is a ProFlame 2 system fitted with the “On Demand” Pilot, a safety feature which will shut down the gas valve completely by extinguishing the
pilot light in the event of a continuous full seven days of inactivity.
This only applies if the CPI (continuous pilot) switch is in the “on” position in your remote control transmitter.
Each time the main burner shuts down, manually or through the call from the thermostat, the seven day timer starts again.
The seven day inactivity timer is controlled within the circuit board. Therefore, if in CPI mode and when the pilot light is extinguished after seven straight days
of inactivity, the CPI setting on the remote control transmitter will remain in the “CPI” (continuous pilot) position. Therefore, all that is required to relight the pilot
would be to press the on/off button on the remote control transmitter from “on” to “off” and back to “on”. Once the pilot has re-established operation will resume
as normal. There is no requirement to do anything with the IPI/CPI mode on the remote control transmitter.
If the unit never goes as long as seven full days without a call for heat, the pilot will remain lit until it is manually shut-off.
If the unit is being operated in IPI (intermittent pilot) mode, neither the above instructions nor the seven day timer will apply.
See the instructions in this manual and on the Lighting Instructions plate on the appliance to light or re-light the pilot.

12 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
owner's information
COPY OF THE LIGHTING PLATE INSTRUCTIONS
919-649
Part #: 919-649
Colours: Black on Grey, except for parts indicated as being Red.
Punch out .25" hole top right corner where indicated.
Size: 100%
w- 6.52"
h- 11.13"
Apr 05/16: Created decal
Apr. 26/16: Added Fr. Headers/warnings
w- 6.5"
h- 11"
A) This appliance is equipped with an ignition device which automatically lights the pilot.
Do not try to light the pilot by hand.
B) BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the oor
because some gas is heavier than air and will settle on the oor.
WHAT TO DO IF YOU SMELL GAS
- Do not try to light any appliance.
- Do not touch any electric switch, do not use any phone in your building.
- Immediately call your gas supplier from a neighbours phone. Follow the gas supplier’s instructions.
- If you cannot reach your gas supplier, call the re department.
C) Do not use this appliance if any part has been under water. Immediately call a qualied service
technician to inspect the appliance and replace any part of the control system and any
gas control which has been underwater.
A) Cet appareil est muni d’un dispositif d’allumage qui allume automatiquement la veilleuse.
Ne tentez pas d’allumer la veilleuse manuellement.
B) AVANT LA MISE EN MARCHE, reniez tout autour de l’appareil pour déceler une odeur de gaz. Reniez au niveau du plancher, car certains gaz
sont plus lourds que l’air et peuvent s’accumuler au niveau du sol.
QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ :
• Ne tentez pas d’allumer l’appareil
• Ne touchez à aucun interrupteur; n'utilisez pas de téléphones se trouvant dans le bâtiment.
• Appelez immédiatement votre fournisseur de gaz depuis un téléphone extérieur. Suivez les instructions du fournisseur.
• Si vous ne pouvez pas rejoindre le fournisseur, appelez le service incendie.
C) N’utilisez pas cet appareil s’il a été plongé dans l’eau, même partiellement. Faites inspecter l’appareil par un technicien qualié et remplacez
tout élément du système de contrôle ou de commande qui a été plongé dans l’eau.
DO NOT REMOVE THIS INSTRUCTION PLATE
NE PAS ENLEVER CETTE ÉTIQUETTE D’INSTRUCTIONS
TO TURN OFF GAS APPLIANCE / POUR ÉTEINDRE UN APPAREIL AU GAZ
This appliance must be installed in accordance with local codes, if any; if none, follow the National Fuel Gas Code, ANSI Z223.1/NFPA 54,
or Natural Gas and Propane Installation Codes, CSA B149.1.
Cet appareil doit être installé conformément aux codes locaux, s’il y a lieu. En l’absence de tels codes, suivre le National Fuel Gas Code,
ANSI Z223.1/NFPA 54, ou les Natural Gas and Propane Installation Codes, CSA B149.1.
CAUTION: Hot while in operation. Do not touch. Severe burns may result. Due to high surface temperatures keep
children, clothing and furniture, gasoline and other liquids having ammable vapors away. Keep burner and control
compartment clean. See installation and operating instructions accompanying appliance.
ATTENTION : Surfaces chaudes lorsque l’appareil est en marche. Ne pas toucher. Risque de brûlures graves. En raison
des températures élevées, les enfants, les vêtements et le mobilier, le carburant et tout autre liquide aux vapeurs
inammables doivent être tenus éloignés de l’appareil. Nettoyer régulièrement le brûleur et le compartiment des
commandes. Voir les consignes d’installation et d’utilisation fournies avec l’appareil.
WARNING: If you do not follow these instructions exactly, a fire or explosion may result causing property damage,
personal injury or loss of life. Improper installation, adjustment, alteration, service or maintenance can cause injury or
property damage. Refer to the owner’s information manual provided with this appliance. For assistance or additional
information consult a qualified installer, service agency or gas supplier.
AVERTISSEMENT : Quiconque ne respecte pas scrupuleusement les instructions de la présente notice risque de déclencher
un incendie ou une explosion pouvant entraîner des dégâts matériels ou des blessures pouvant être mortelles.
Tout défaut d'installation, de réglage, de modication, de service ou d'entretien peut entraîner des blessures ou des dom-
mages matériels. Reportez-vous au manuel d'utilisation fourni avec cet équipement. Pour obtenir de l'aide ou des informa-
tions complémentaires, consulter un installateur ou un service d'entretien qualié, ou le fournisseur de gaz.
1) Ensure the Main switch is in the ON position and/or the wall mounted battery holder (if equipped) is in the <REMOTE> position.
2) Press and release the ON/OFF button on the remote handheld transmitter. An audible beep should be heard from the receiver. If not
using the remote, the unit can also be turned on by sliding the battery holder switch to the <ON> position (if equipped).
3) After approximately 4 seconds the spark ignition system will spark for 60 seconds to light the main burner.
4) The unit will turn on.
Note: The rst attempt to ignition will last approximately 60 seconds. If there is no ame ignition (rectication) the board will stop spark-
ing for approximately 35 seconds. After this wait time, the board will start a second try for ignition by sparking for approximately 60
seconds. If there is still no positive ignition after the second attempt the board will go into lock out.
The system will need to be reset as follows (after going into lock out mode):
a) Wait 5 minutes - turn the system o󰀨 by pressing the ON/OFF button on the remote.
b) After approximately 2 seconds press the ON/OFF button again.
c) Unit will repeat step 2.
1) S’assurer que le commutateur principal est en position ON et/ou que le bloc-piles mural (le cas échéant) est en position <REMOTE>.
2) Appuyer sur la touche ON/OFF de la télécommande puis relâcher. Un bip sonore retentira depuis le récepteur. Si vous n'utilisez pas
la télécommande, l'appareil peut également être allumé en faisant glisser le commutateur du bloc-piles sur la position <ON> (le cas
échéant).
3) Après environ 4 secondes, le système d'allumage produira une étincelle pendant 60 secondes pour allumer le brûleur principal.
4) L'appareil s’allumera.
Remarque : Au premier allumage, le système tente d’allumer les ammes pendant 60 secondes. Si l’essai est infructueux, le système
fera une pause de 35 secondes. C’est ce qu'on appelle l'étape de rectication. Ce délai écoulé, le système tente à nouveau d'allumer les
ammes en produisant des étincelles pendant 60 secondes. Si les ammes ne s’allument toujours pas, le système se met en mode ver-
rouillage.
Il faut alors le réinitialiser en suivant les étapes ci-dessous (pour le déverrouiller) :
a) Attendre 5 minutes et éteindre l’appareil en appuyant sur la touche ON/OFF de la télécommande.
b) Attendre 2 secondes et appuyer encore une fois sur la touche ON/OFF.
c) L'appareil répètera l'étape 2.
1) Press the ON/OFF button on the remote.
2) If service is to be performed–you must disconnect power and shut off gas to the unit.
1) Appuyer sur la touche ON/OFF de la télécommande.
2) Lors de l'entretien de l'appareil, vous devez débrancher l'alimentation électrique et couper le gaz alimentant l'appareil.
LIGHTING INSTRUCTIONS / CONSIGNES D’ALLUMAGE
FOR YOUR SAFETY READ BEFORE LIGHTING
POUR VOTRE SÉCURITÉ – À LIRE AVANT LA MISE EN MARCHE

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 13
owner's information
PROFLAME II REMOTE CONTROL OPERATING INSTRUCTIONS
Figure 2: Transmitter LCD Display
OPERATING PROCEDURE
Initializing the System for the First Time
Power the receiver. Press the PRG button located on the top right hand
corner of receiver. The receiver will beep three times to indicate that it
is ready to synchronize with a transmitter. Install the 3 AAA type batter-
ies in the transmitter battery bay, located on the base of the transmitter
(fig. 3). With the batteries already installed in the transmitter, opush
the ON button. The receiver's command is accepted and sets to the
particular code of that transmitter. The system is now initialized.
(*) The receiver may be independent or integral jto the IFC hearth appli-
ance control module. The receiver instruction may not be independent
when part of the IFC.
Figure 3: Battery Compartment
WARNING: THE TRANSMITTER AND IFC ARE RADIO FRE-
QUENCY DEVICES.
The Proflame 2 Transmitter provides for controlling the following hearth
appliance functions:
1. Main Burner On/Off
2. Main Burner flame modulation (6 levels)
3. Choice of standing or intermittent pilot (CPI/IPI)
4. Thermostat and Smart thermostat functions
5. Accent light modulation (6 levels)**
6. Split flow valve**
7. Comfort Fan speed modulation (6 levels)**
** This feature is not available on any Hampton models.
IMPORTANT:The Proflame Transmitter 2 is an integrated part of the
Proflame 2 System, which consists of these elements:
• Proflame 2 Transmitter, to be used in conjunction with:
• Integrated Fireplaces Control (Proflame 2 IFC)
The Proflame Transmitter uses a streamline design with a simple button
layout and informative LCD display (Fig. 1). A Mode Key is provided to
index between the features and a Thermostat Key is used to turn on/off
or index through Thermostat functions (Fig. 1 & 2). Additionally, a Key
Lock feature is provided (Fig. 22).
TECHNICAL DATA
REMOTE CONTROL
Supply Voltage 4.5V (three 1.5V AAA batteries)
Ambient temperature
ratings
0 - 50oC (32 - 122oF)
Radio Frequency 315 MHZ
ATTENTION!
- Turn “OFF” the main gas supply of the appliance during installation or
maintenance of the IFC.
- Turn “OFF” main gas supply to the appliance prior to removing or
reinserting the batteries.
- In case of remote control malfunction, turn off the IFC device using
the "ON/OFF" main switch.
- For installation / maintenance, switch off the IFC device removing
main power supply plug.
Figure 1: Proflame Transmitter

14 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
owner's information
Smart Thermostat (Transmitter Operation)
The Smart Thermostat function adjusts the flame height in accordance
to the difference between the set point temperature and the actual
room temperatures. As the room temperature gets closer to the set
point the Smart Function will modulate the flame down.
To activate this function, press the Thermostat Key (Fig. 1) until the
word "SMART" appears to the right of the temperature bulb graphic
(Fig. 11).
To adjust the set temperature, press the Up or Down Arrow Keys until
the desired set temperature is displayed on the LCD screen of the
Transmitter (Fig. 12).
Note. When Smart Thermostat is activated, manual flame height
adjustment is disabled.
Figure 12Figure 11: Smart Flame Function
Fan Speed Control**
If the appliance is equipped with a hot air circulating fan, the speed of
the fan can be controlled by the Proflame system. The fan speed can
be adjusted through six (6) speeds. To activate this function use the
Mode Key (fig.1) to index to the fan control icon (Fig. 13). Use the Up/
Down Arrow Keys (fig.1) to turn on, off or adjust the fan speed (fig. 14).
A single “beep” will confirm reception of the command.
Figure 13 Figure 14
Remote dimmer control (Light)**
The auxiliary function controls the AUX power outlet by the dimmable
light control. To activate this function use the Mode Key (fig. 1) to index
to the AUX icon (fig. 15 & 16).
The intensity of the output can be adjusted through six (6) levels. Use
the Up/Down Arrow Keys (Fig.1) adjust the output level (Fig. 16). A
single “beep” will confirm reception of the command.
Note: This function is available only with the IFC Control Module.
Figure 15 Figure 16
Split Flow control**
The secondary burner is controlled by the split Flow. To activate this
function use the Mode Key (fig. 1) to index to the SPLIT FLOW mode
icon (fig. 17 & 18).
Pressing the Up Arrow Key will activate the secondary burner. Pressing
the Down Arrow Key will turn the secondary burner off. A single “beep”
will confirm the reception of the command.
Figure 17 Figure 18

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 15
owner's information
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
Note: Power vent models do not have a Continuous
Pilot option.
With the system in "OFF" position press the Mode Key (fig. 1) to index
to the CPI mode icon (fig. 19 & 20).
Pressing the Up Arrow Key will activate the Continuous Pilot Ignition
mode (CPI). Pressing the Down Arrow Key will return to IPI. A single
“beep” will confirm the reception of the command.
Figure 20
KEY LOCK
This function will lock the keys to avoid unsupervised operation.
To activate this function, press the MODE and UP Keys at the same
time (fig. 21).
To de-activate this function, press the MODE and UP Keys at the
same time.
Figure 21
LOW BATTERY POWER DETECTION
Transmitter
The life span of the remote control batteries depends on various fac-
tors: quality of the batteries used, the number of ignitions of the appli-
ance, the number of changes to the room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon will appear on
the LCD display of the Transmitter (Fig. 22) before all battery power is
lost. When the batteries are replaced this Icon will disappear.
Figure 22
CPI/IPI SWITCH
This appliance comes equipped with a CPI/IPI switch. The functions of
both the CPI/IPI switch are as follows:
Continuous pilot (CPI) - A pilot that when in operation, is intended to
remain continuously ignited until it is manually interrupted.
Intermittent pilot (IPI) - A pilot that is automatically ignited when an
appliance is called on to operate and which remains continuously
ignited during each period of main burner operation. The pilot is
automatically extinguished when each main burner operating cycle is
completed. The mode of the fireplace is easily changed from an inter-
mittent pilot ignition system (IPI) to a continuous pilot ignition system
(CPI) by using remote control as noted above.
The benefits of having as CPI are as follows:
- Keeps venting primed for trouble free start-up under colder weather
conditions or inversions.
- Keeps the unit glass warm, which decreases the amount of conden-
sation on start-up
-Provides owners with flexibility to choose a traditional continuous pilot.
The primary benefit of having the IPI function is a significant savings
on fuel as the pilot will only run when there is a call for heat.
Thermostat Icon: If the thermostat icon is not present on the remote
transmitter, follow instructions noted below:
1. Remove one battery from the remote.
2. Press and hold down the Thermostat button on the remote.
3. Reinstall the battery(removed in Step 1) while still holding down
thermostat button.
4. If you see "Set" the thermostat option is now enabled. If you see
"Clr" the thermostat option is now disabled.
5. Repeat the procedure if the "Set" or "Clr" to remove or add the op-
tion back to the remote did not appear.
Enable all other functions if not present on the remote transmitter, fol-
low instructions noted below:
1. Remove one battery from remote.
2. Press and hold both the ON/OFF and MODE button at the same
time .
3. Reinstall battery removed in Step 1 while holding both buttons—
keep holding buttons, then release the MODE button only.
4. The screen will show either "Clr" or "Set" as the first option avail-
able is to disable or enable a mode.
5. "Clr" will remove a mode—use the up or down arrow while hold-
ing down ON/OFF and MODE (mode icon will disappear once
removed).
6. Use the "MODE" button to move to the next function.
7. "Set" will add a mode —use the up or down arrow while holding
down ON/OFF and MODE (mode icon will appear when added).
8. Use the "MODE" button to move to the next function.
Note: You should never program out the fan (if installed) or CPI/IPI
mode on the remote.

16 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
owner's information
Continuous Pilot/Intermittent Pilot (CPI/IPI) selection
Note: Power vent models do not have a Continuous
Pilot option.
With the system in "OFF" position press the Mode Key (fig. 1) to index
to the CPI mode icon (fig. 19 & 20).
Pressing the Up Arrow Key will activate the Continuous Pilot Ignition
mode (CPI). Pressing the Down Arrow Key will return to IPI. A single
“beep” will confirm the reception of the command.
Figure 19 Figure 20
KEY LOCK
This function will lock the keys to avoid unsupervised operation.
To activate this function, press the MODE and UP Keys at the same
time (fig. 21).
To de-activate this function, press the MODE and UP Keys at the
same time.
Figure 21
LOW BATTERY POWER DETECTION
Transmitter
The life span of the remote control batteries depends on various fac-
tors: quality of the batteries used, the number of ignitions of the appli-
ance, the number of changes to the room thermostat set point, etc.
When the Transmitter batteries are low, a Battery Icon will appear on
the LCD display of the Transmitter (Fig. 22) before all battery power is
lost. When the batteries are replaced this Icon will disappear.
Figure 22
CPI/IPI SWITCH
This appliance comes equipped with a CPI/IPI switch. The functions of
both the CPI/IPI switch are as follows:
Continuous pilot (CPI) - A pilot that when in operation, is intended to
remain continuously ignited until it is manually interrupted.
Intermittent pilot (IPI) - A pilot that is automatically ignited when an
appliance is called on to operate and which remains continuously
ignited during each period of main burner operation. The pilot is
automatically extinguished when each main burner operating cycle is
completed. The mode of the fireplace is easily changed from an inter-
mittent pilot ignition system (IPI) to a continuous pilot ignition system
(CPI) by using remote control as noted above.
The benefits of having as CPI are as follows:
- Keeps venting primed for trouble free start-up under colder weather
conditions or inversions.
- Keeps the unit glass warm, which decreases the amount of conden-
sation on start-up
-Provides owners with flexibility to choose a traditional continuous pilot.
The primary benefit of having the IPI function is a significant savings
on fuel as the pilot will only run when there is a call for heat.
Thermostat Icon: If the thermostat icon is not present on the remote
transmitter, follow instructions noted below:
1. Remove one battery from the remote.
2. Press and hold down the Thermostat button on the remote.
3. Reinstall the battery(removed in Step 1) while still holding down
thermostat button.
4. If you see "Set" the thermostat option is now enabled. If you see
"Clr" the thermostat option is now disabled.
5. Repeat the procedure if the "Set" or "Clr" to remove or add the op-
tion back to the remote did not appear.
Enable all other functions if not present on the remote transmitter, fol-
low instructions noted below:
1. Remove one battery from remote.
2. Press and hold both the ON/OFF and MODE button at the same
time .
3. Reinstall battery removed in Step 1 while holding both buttons—
keep holding buttons, then release the MODE button only.
4. The screen will show either "Clr" or "Set" as the first option avail-
able is to disable or enable a mode.
5. "Clr" will remove a mode—use the up or down arrow while hold-
ing down ON/OFF and MODE (mode icon will disappear once
removed).
6. Use the "MODE" button to move to the next function.
7. "Set" will add a mode —use the up or down arrow while holding
down ON/OFF and MODE (mode icon will appear when added).
8. Use the "MODE" button to move to the next function.
Note: You should never program out the fan (if installed) or CPI/IPI
mode on the remote.

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 17
installation
General Safety Information
1. The appliance installation must conform with
local codes or in the absence of local codes,
with CAN/CGA B149 (in Canada) or the National
Fuel Gas Code ANSI Z223.1 in the U.S.A. This
appliance should be installed by a qualified gas
fitter technician only.
2. Installation and repair should be done by a
qualified service person.
3. The appliance should be inspected before use
and at least annually by a professional service
person. More frequent cleaning may be required
due to excessive lint from carpeting, bedding
material, animal hair, etc. It is imperative that
control compartments, burners and circulating
air passageways of the appliance be kept clean.
4. See general construction and assembly
instructions. This appliance may only be
installed in a vented, noncombustible fireplace.
5. This appliance is listed for bedroom installations
when used with a listed Millivolt Thermostat.
Some areas may have further requirements,
check local codes before installation.
6. Always connect this insert to a vent system
venting to the outside of the building envelope.
Never vent to another room or inside a building.
Make sure that the vent is properly sized and is
of adequate height to provide the proper draft.
7. Inspect the venting system annually for blockage
and any signs of deterioration.
8. Any glass removed for servicing must be
replaced prior to operating the appliance.
9. To prevent injury, do not allow anyone who is
unfamiliar with the operation to use the fireplace.
10. This appliance cannot be operated without brick
or enamel panels in place.
11. Due to high temperatures, the appliance should
be located out of high traffic areas and away
from furniture and draperies. Children and
adults should be alerted to the hazards of high
surface temperatures, especially the fireplace
glass and gold trims, and should stay away to
avoid burns or clothing ignition. Young children
should be carefully supervised when they are
in the same room as the appliance. Clothing or
other flammable material should not be placed
on or near the appliance.
GAS PRESSURE
TESTING
The appliance must be isolated from the gas sup-
ply piping system by closing its individual manual
shut off valve during any pressure testing of the
gas supply piping system at test pressures equal
to or less than 1/2 psig. (3.45 kPa).
INSTALLATION INTO A SOLID FUEL
BURNING FIREPLACE OR FACTORY
BUILT FIREPLACE
The LRI3E-11/HRI3E-11 Gas Inserts have been
tested and approved to be vented into any masonry
fireplace or approved solid fuel burning factory built
fireplace that will allow the insert to physically fit into
the firebox. Refer to "Minimum Fireplace Dimen-
sions" section for minimum fireplace clearances.
If the factory built fireplace* height is too low for
your Insert, you may remove the smoke baffle
plate, damper, refractory (firebricks), glass doors,
screen rails, screen mesh and log grates from the
factory built fireplace as long as these items are
saved and are reinstalled in the event that the Insert
is removed. The fireplace flue damper can be fully
blocked open or removed for installation of the gas
fireplace insert.
Smoke shelves, shields and baffles may be removed
if attached by mechanical fasteners. If any part is
removed it must not weaken the structural integrity
of the factory built fireplace.
The fireplace and fireplace chimney must be clean
and in good working order and constructed of non-
combustible materials.
The surround panels should not seal ventilation
openings on the fireplace.
Chimney clean outs should fit properly.
NOTE: Any alterations made to the listed solid fuel
burning factory built fireplace may void the listing
of the fireplace.
Cutting any sheet metal part of the fireplace, in
which the gas fireplace insert is to be installed is
prohibited.
*Check with your local inspector before commencing
with this installation.
Installer must mechanically attach the supplied
label to the inside of the firebox of the fireplace into
which the gas fireplace insert is installed.
"WARNING: This fireplace has been converted
for use with a gas fireplace insert only and
cannot be used for burning wood or solid fuels
unless all original parts have been replaced,
and the fireplace re-approved by the authority
having jurisdiction."
FACTORY-BUILT (METAL) WOOD-
BURNING FIREPLACE
REQUIREMENTS
NOTE: Any parts that are removed must be removed
in a way that would allow them to be re-installed if
the insert is ever removed (removal of rivets or
screws is acceptable).
To reference parts—see illustration below.
Must be removed:
1 -Damper
2- Grate (with log set)
May be removed (if applicable):
3- Smoke shelf
4- Internal baffles
5 - Screen
6 & 7 - Masonry lining or refractory
8 - Metal or glass doors
The fireplace must be permanently marked to
indicate that it has been altered and is no longer
suitable for burning solid fuel (wood), unless the
removed parts are re-installed. Cutting of any sheet
metal parts is prohibited.
May be removed (in certain cases):
9 -Metal floor of the firebox
10 - The insulation and any structured rigid frame
members must not be removed or altered (side and
top of door frame, side and top of the face of the
fireplace, metal sides, etc.).
If the factory-built fireplace has no gas access
hole(s) provided, an access hole of 1.5 inch (37.5
mm) or less may be drilled through the lower sides
or bottom of the firebox in a proper workmanship
like manner. This access hole must be plugged
with non-combustible insulation after the gas
supply line has been installed.
CAUTION:
Firebox floor removal is not covered under the
appliance safety standard (ANSI Z21.88, CSA
2.33) used in the safety certification of this ap-
pliance. The Intertek safety certification does
not apply to this method of installation. Before
installing the appliance using this method, contact
the Authority Having Jurisdiction to determine
if this installation is acceptable in your area.
The sheet metal base of the fireplace must be
left in place and a minimum 1/2" cement board
sheet placed under the entire length and width
of the appliance.
WARNING: Failure to position the parts
in accordance with the diagrams in this
manual or failure to use only parts specifi-
cally approved with this appliance may re-
sult in property damage or personal injury.

18 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
installation
A
B
C
MATERIALS REQUIRED
A 120 Volt AC power cord is hooked up to operate the fan and operate the gas valve when batteries are
not installed in the receiver. Plug the 3 wire cord into a suitable receptacle. Do not cut the ground
terminal off under any circumstances. When connected with 120 volts, the appliance must be
electrically grounded in accordance with local codes, current version of CSA C22.1 (in Canada) or in
the absence of local codes, with the National Electrical Code ANSI/NFPA 70-1987.
INSTALLATION
CHECKLIST
Before installing vent system ensure that the damper
plate is open and secure to prevent the damper plate
from falling down and crushing the liner.
The Regency Gas Insert is installed as listed.
1. Check all clearances to combustibles, (Refer to
sections "Minimum Fireplace Dimensions and
Clearances to Combustibles)
2. Make the gas connection. (Refer to section "Gas
Connection")
3. Install the two liners (2" intake and 3" exhaust)
to the sliding connector plate. (Refer to section
"Flue Liner Installation.")
4. Slide the unit half way into the fireplace.
5. Pull the vent connector plate through the tapered
brackets and fasten to the front plate. Refer to
section "Flue Liner Installation."
6. Slide the unit fully into the fireplace. Level if
necessary.
7. Hook up 120 volt AC power cord into a suitable
receptacle. Optional: Install 4 batteries in the
battery pack. Batteries only serve as back up
if power is lost within the home.
8. Test gas pressure (Refer to section "Gas Pipe
Pressure Testing"). Check aeration system
(Refer to section "Gas Insert Aeration System").
9. Install standard and optional features. Refer to
the following sections:
a. Brick Panels (LRI3E) or
Enamel Panels (LRI3E,HRI3E)
NOTE: Painted panels come with HRI3E.
(Panels - must be installed to operate unit)
b. Log Set
c. Glass Crystals
d. Spa stones
e Vignette Faceplate
f. Mantel deflector
g. Hearth Trim
h. Backing plate/4 sided backing plate
10. Final check: Before leaving this unit with the
customer, the installer must ensure that the
appliance is firing correctly. This includes:
a) Clocking the appliance to ensure the correct
firing rate.
b) Adjusting the primary air, if required, to
ensure that the flame does not carbon. See
"Gas Insert Aeration System" section.
c) Ensuring that the appliance is venting
correctly.
MINIMUM FIREPLACE DIMENSIONS
The minimum fireplace clearances & dimensions for the Regency gas insert are shown in the following
diagrams:
Max Lintel Bar
Depth
A
Height
B
Depth
C
Width
(rear)
D
Width
(front)
E
Width
F
Front Depth
To Taper
G
Vignette
Faceplate 8-5/8" 19-1/2" 14-1/2" 21-5/8" 28-1/2" 31-1/8" 4"
Arched
Vignette
Faceplate
8-5/8" 19-1/2" 14-1/2" 21-5/8" 28-5/8" 31-1/8" 4"

LRI3E-11 / HRI3E-11 Direct Vent Gas Insert | 19
installation
Diagram 1
Diagram 3
Diagram 2
Note: A 3-1/2" mantel deflector to reduce
mantel height to 28" from bottom of
unit @ 1"depth.
A noncombustible mantel may be
installed at a lower height if the
framing is made of metal studs
covered with a non-combustible
board.The non-combustible mantel
MINIMUM CLEARANCES TO COMBUSTIBLES
The clearances listed below are minimum distances unless otherwise stated:
A major cause of fires is failure to maintain required clearances (air space) to combustible materials. It is of the greatest importance that this
decorative gas appliance be installed only in accordance with these instructions.
Clearance: Dimension Measured From:
A: Sides 6" / 152 mm ***From inside edge of faceplate / doors
B: Ceiling 60" / 1524 mm From Base of Unit
C: Mantel (Min. Height) *28" / 711mm
38"/ 965mm
From Base of Unit
From Base of Unit
D:Min. Hearth Depth 12" / 305mm Not required if unit raised 3-1/2" off floor
E: Min. Hearth Length 36"/ 914mm
G: Max. Mantel Depth 0-12" / 305 mm @ 47" (1193mm) from bottom of unit
without deflector @12" (305mm) deep
@ 37" (940mm) from bottom of unit with
3-1/2" deflector @12" (305mm) deep
K: Min. Alcove Width 54" / 1372 mm
L: Max. Alcove Depth 36" / 914 mm
M: Mantel Deflector 3-1/2"/ 89mm
NOTE: 36” (914 mm) wide x 12” (305mm) deep non combustible hearth is required in front
of the appliance, unless the unit is raised 3-1/2” (89 mm) off the floor surface.
*An optional 3-1/2" deflector, reduces the mantel height to 28" from bottom of unit
@ 1"depth.
(J): ***Measured from inside edge of faceplate/doors - Reference Only: 27-1/4'' / 692mm
A
C
B
E
K
D
L
G
J
Mantel Clearances
2
0
12 64
810
0
24
12
16
20
12" (305mm)
1" (25mm)
19" (483mm)
19"(483mm)
to base of unit Side View
32
28
4
8
28" (711mm)
Top of fireplace
opening
Non Combustible
Combustible
Mantel Clearances
2
0
12 64
810
0
24
12
16
20 12" (305mm)
1" (25mm)
9" (229mm)
19"(483mm)
to base of unit Side View
32
28
Combustible
4
818" (457mm) Deflector
Top of fireplace
opening
Non Combustible
MANTEL CLEARANCES WITHOUT DEFLECTOR MANTEL CLEARANCES WITH 3-1/2" DEFLECTOR
WARNING
Although this appliance passes safety
certification, the hearth in front of the fireplace
becomes very hot when the fireplace heats. Do
not use the hearth as a seat or shelf.
when installed at a lower
overall height may not be
lower than 6 inches from the
top of the fireplace opening.
Note: All material used must be
completely non-combustible.

20 | LRI3E-11 / HRI3E-11 Direct Vent Gas Insert
installation
GAS CONNECTION
1. If the appliance is to be installed into an existing
chimney system, thoroughly clean the masonry
or factory built fireplace.
2. The appliance is provided with an opening on
the left hand side of the control compartment.
A 3/8" NPT gas supply pipe must be brought
near this inlet hole.
3. Locate the center point where the vent will pass
through the chimney above the appliance. Move
the appliance into the exact location where it is
to be installed. Ensure that the Insert is level.
4. Do not cut any sheet-metal parts of the fire-
place, in which the gas fireplace insert is to
be installed.
5. If the factory-built fireplace has no gas access
hole(s) provided, an access hole of 1-1/2"
(37.5mm) or less may be drilled though the
lower sides or bottom of the firebox in a
proper workmanship like manner. This access
hole must be plugged with a non-combustible
insulation after the gas supply line has been
installed.
GAS CONNECTION WARNING:
Only persons licensed to work with
gas piping may make the necessary
gas connections
to this appliance.
Gas & Electrical Connections
Minimum 8 ft. (2.44m)
Maximum 35 ft. (10.67m)
Exhaust
Flue
2” Liner 3” Liner
3” Collar
Flashing
FPI Co-linear DV
Vertical Termination Cap
Full continuous length
(unit to cap) is required
for both intake & exhaust.
The LRI3E-11/HRI3E-11 are also approved for use with a 2" liner for air
intake and a 3" liner for exhaust. This would be suitable for a Class A wood
burning chimney with a minimum 6" round flue.
The chimney must be lined with one 2" diameter liner for intake and one 3"
diameter liner for exhaust. The minimum vent length is 8' and maximum is 35'.
The Air Intake pipe must be attached to the inlet air collar of the termination
cap. Periodically check that the vent is unrestricted.
INSTALLATION WITH 3" & 2" LINERS
Vent Run Vent Restrictor Position
Up to 8' Position 1
Beyond 8' No restrictor
NOTE: See instructions in the "Vent Restrictor Position"
section on positioning of the vent restrictor.
THE APPLIANCE MUST NOT BE CONNECTED TO A CHIMNEY
FLUE SERVING A SEPARATE SOLID FUEL BURNING APPLIANCE.
Masonry chimneys may take various contours which the flexible liner will
accommodate. However, keep the flexible liner as straight as possible,
avoid unnecessary bending.
Part # Description
948-305 3" Flex - 35 ft. (exhaust)
948-316 2" Flex - 35 ft. (intake)
946-582 Regency Co-linear DV Vertical Termination Cap, Flashing &
2" Collar
IMPORTANT : Use only the listed termination caps/flex liner noted below
and on next page. This appliance was tested/certified as a
complete system with the noted termination caps and flex
liner. Use of other termination caps/flex liner not listed in
this manual will void the warranty and certification of this
appliance. It is also important not to enclose the termina-
tion cap inside a masonry chimney rain cap, or similar. The
termination must be exposed on all four sides and above
to exhaust and to draw air into the firebox.