Regency GRAND MARQUIS User manual

• GRAND MARQUIS •
• CEILING FAN OWNER'S MANUAL •
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
Style that revolves around you.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS
IMPORTANT SAFEGUARDS:
1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly
To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly
before beginning.
before beginning.
2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All
electrical connections must be made in accordance with local codes, ordinances and/or the National Electric
Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a
qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling
members and make the proper installation(s) and connections.
3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades
should be at least 7 feet from floor.
4. When mounting on a ceiling outlet box, an approved box UL listed as "suitable for fan support"
"suitable for fan support"
is required. The
box and its supporting members must be able to support the moving weight of the fan's listed weight. The box
must not be able to twist or work loose. Installation on a concrete ceiling should be performed by qualified
personnel.
5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the
carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure
that you do not mix fan blade sets
do not mix fan blade sets
, as each blade is part of a weighted set.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one
side of the outlet box, and the "HOT" wires on the other side.
7. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed and
should be installed per the light kit's installation instructions.
8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling
and/or causing damage or injury.
9. The fan can be made to work immediately after installation - the bearings are adequately charged with grease so
that, under normal conditions, further lubrication should not be necessary for the life of the fan.
10. Do not operate the reverse switch while the fan blades are in motion. The fan must be turned off and the blades
stopped before reversing the blades direction.
11. ATTENTION: Fan includes a 190w limiter to comply with the department of energy 2009 regulation. Lamping
this product over 190w will cause this fan to not light. Please use bulbs with a total wattage under the 190w
regulation.
1
Weight of Fan: 22.6 Lbs

IMPORTANT SAFETY PRECAUTIONS
• Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
Disconnect power by removing fuse or turning off circuit breaker before installing the fan and/or optional lighting.
• Support directly from building structure.
• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan
"acceptable for fan
support"
support"
and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support
of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if
in doubt.
• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.
• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or
cleaning the fan. Do not insert any object(s) between rotating fan blades.
NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all
NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness
possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness
are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring
are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring
for, and operating the unit.
for, and operating the unit.
2
Thank you for choosing a Regency Ceiling Fan. You have chosen the best!
Your new ceiling fan has been designed to provide many years of service and enjoyment.
Warnings:
Warnings:
TOOLS AND MATERIALS REQUIRED
• Phillips screwdriver
• Blade screwdriver
• Wrench or pliers
• Wire cutter
• Stepladder
• Wiring supplies as required by
electrical code

UNPACKING YOUR FAN
1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever
necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor
housing on its side, or the decorative housing may shift, be bent or damaged.
2. Examine all parts. You should have the following:
1. Fan blades (5)
2. Hanging bracket
3. Ceiling canopy
4. Canopy screw cover plate
5. Downrod/ball assembly
6. Coupling cover
7. Fan housing with motor (Remove rubber shipping supports around motor, if included on your fan. Save screws.)
8. Blade arms (5)
9. Switch housing
10. Light kit
11. Globe
12. Pull chains with fobs (2)
13. 60W candelabra bulbs (3)
14. Bracket mounting hardware (wood screws, screws, lock washers, washers, wire nuts)
15. Blade arm to blade screws, w/washers (16)
16. "
16. "S
" hook (
" hook (
Used for hugger style mounting.)
Used for hugger style mounting.)
NOTE:
NOTE:
Design of parts shown above may look slightly different for your specific model of fan.
3
2
6
7
8
9
10
11
12
15
13
14
16
4
5
3
1

PREPARATION
PREPARATION:
Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor
from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor
box. Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.
Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.
Caution:
Caution:
To avoid possible electrical shock, be sure
electricity is turned off at the main power box before wiring.
All wiring must be in accordance with National and Local
Electrical Codes and the ceiling fan must be grounded as a
precaution against possible electric shock.
1. Locate ceiling joist where fan is to be mounted, being
sure location agrees with the requirements in the
minimum clearance section of this guide. Wood joist
must be sound and of adequate size to support 35 lbs.
(See Page 1, Items 3 and 4).
2. If not already present, mount a UL listed outlet box
marked "suitable for fan support" following the
instructions provided with the outlet box. The outlet box
must be able to support a minimum of 35 pounds.
3. Attach hanger bracket to outlet box using screws
using screws
provided with the outlet box.
provided with the outlet box.
4
Parts identification on assembled fan
INSTALLING THE HANGING BRACKET
Ceiling Fan
Outlet Box
Hanger
Bracket
Outlet Box
Screw
Flat Washer
Spring Washer
Blades
Canopy
Downrod
Motor Housing
Blade Arms
Globe

INSTALLING THE FAN
The HUGGER method is preferred if maximum headroom is required. The ceiling must be horizontal, not sloped.
Blades will be approximately 8' from the ceiling. Air flow will be reduced when the fan is installed using the
HUGGER method.
5
INSTALLATION:
This fan has two installation options:
#1 HUGGER MOUNTING
The DOWNROD MOUNTING method is preferred if the ceiling is sloped or vaulted, or if the ceiling is extra high
and requires the use of an extension downrod. Blades will be approximately 12' from ceiling using supplied downrod.
#2 DOWNROD MOUNTING
This is the recommended mounting for ceilings 8' and higher.

INSTALLING THE FAN - HUGGER STYLE
NOTE: The S hook is to be used for hugger style mounting.
1. Remove the plastic trim ring from the canopy to expose the 6 mounting holes. The downrod, ball and cotter pin will
not be used for this mounting (Fig. 1).
2. Feed fan wires through the canopy and position the canopy over the mounting collar on top of the fan. The collar's 2
security screws will not be used and can be turned all the way into the collar to make attaching the canopy easier.
3. Align the canopy on top of the fan so the 3 large holes are over the 3 screws holding the collar to the fan. The 3 small
holes will then be aligned with the 3 open holes in the top of the fan.
4. Securely attach the canopy to the top of the fan using the 3 hugger mounting screws provided.
WARNING: To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling.
5. Place the S hook onto the hanger bracket. Hang the canopy (with the fan motor housing attached) from the S hook on
the hanger bracket using one of the holes in the edge of the canopy (Fig. 2). This will permit you to make the
electrical connections without having to hold the fan up as well.
6. Make the wire connections as described in "Electrical Connections" (page 9).
7. Insert 2 screws into the hanger bracket, leaving them partially out (Fig. 3).
8. Attach the canopy to the hanger bracket by inserting the slotted openings of the canopy on the hanger bracket screws
(Fig. 4), and turn the fan to the right to engage the screws in the slots.
9. Insert the 2 remaining screws through the remaining canopy holes and tighten all 4 screws.
6
Fig. 1 Screws
6-hole
Canopy
Motor
Housing
Fig. 2
Fig. 3
Fig. 4
I NSTALLATION O PTION #1: H UGGER S TYLE M OUNTING
S Hook

INSTALLING THE FAN - DOWNROD STYLE
1. Carefully support fan body (motor) in its styrofoam packing with the mounting collar (where the wires come out)
facing upward.
2. Remove ball from downrod by loosening set screw in the side of the ball. Slide ball down and remove ball pin; remove
ball.
3. Feed the wires from top of fan through the coupling cover end of downrod and set end of downrod into mounting
collar so the hole in the downrod lines up with the hole in the side of the mounting collar.
4. Insert downrod pin through holes in mounting collar and downrod; slip cotter pin through small hole in end of
downrod pin to hold downrod in place.
5. Tighten security screws against downrod using a large flat blade screwdriver to ensure a tight fit against downrod.
Tighten nuts against mounting collar.
NOTE:
NOTE:
Fan has 6 feet of hook-up wire in case
you are using a long extension downrod. Wires
can be cut so only 8 inches or so extend beyond
the top of the downrod to make the electrical
connections easier and safer.
6. Feed wires through canopy and slide canopy
over downrod. It will be attached to ceiling
later.
7. Feed wires through ball and slide ball over
downrod, past hole in the top end of the
downrod. Insert ball pin (removed in step 2),
slide ball up, and tighten set screw to secure
ball in place.
7
INSTALLATION OPTION #2: DOWNROD STYLE MOUNTING
Ground Wire
(Optional extension shown)
Trim Ring
Hook-up (3) Wires
Ball
Canopy
Downrod
Mounting Collar
Downrod Pin
Collar Cover
Security Screws
Cotter Pin
Top of
Fan Body

INSTALLING THE FAN - DOWNROD STYLE
1. Lift ball/downrod/fan into hanger bracket opening. NOTE:
NOTE:
The tab opposite hanger bracket opening should fit in slot
on ball.
2. Make wire connections, (refer to section titled "Electrical Connections").
3. Slide canopy up and fasten to hanger bracket with 4 screws provided.
WARNING:
WARNING:
To avoid damaging the blade arms and blades, do not install them onto fan until fan is fastened to ceiling.
8
INSTALLATION OPTION #2: DOWNROD STYLE MOUNTING (CONT.)
Hanger
Bracket Tab
Ball Slot
Ball

ELECTRICAL CONNECTIONS
*
Be sure electricity is turned off at the main power box before wiring.
1. Four wires are connected to the fan.
Black - this is the "hot" power to run fan.
White - this is the "common" power to run fan and light.
Blue - this is the "hot" power for light kit.
Green - ground wire (on bracket or downrod).
2. If fan and light are to be connected to the same circuit, black and blue wires can both be connected to house circuit
black wire.
NOTE:
NOTE:
The other end of the blue wire, (light circuit) is in the switch housing with a wire nut and label for light kit
attachment. The white wire (common for light kit) is also there.
WARNING:
WARNING:
If light kit is not used, DO NOT connect blue wire at the ceiling.
Fig. 1
Fig. 3
Fig. 2
9

BLADE ATTACHMENT
1. Place fiber washer on screw. Insert this assembly through the blade and start the screw into the blade arm. Repeat
this procedure without tightening the screw until all 3 screws have been started into the blade arm (Fig. 1).
NOTE:
NOTE:
Fans that have painted finishes are packed with gaskets that can be used between the blade arm and blade to
help prevent a clicking noise that may develop if blade screws loosen over time.
2. Tighten each screw starting with center screw.
3. Fasten blade assembly to motor with provided screws and lock lockwashers. Repeat procedure for remaining
blades (Fig. 2). Make sure screws are TIGHT!
TIGHT!
Loose motor screws can contribute to unnecessary hum during
operation.
NOTE:
NOTE:
Cordless power screwdrivers are NOT
NOT
recommended, as they tend to strip the heads of the screws and usually
will not fully compress the lock washers on the motor screws. Use a large flat blade screwdriver for final tightening to
fully compress the washers. This will help ensure proper alignment of the blades and noise-free, wobble-free running.
10
Fig. 1
Fig. 2
Screw Fiber Washer
Blade Arm Blade
Install gasket between
blade arm and blade
(optional)
Screws
Blades Assembly

INSTALLATION THE SWITCH HOUSING AND LIGHT KIT
NOTE: Be sure the power is off before installing.
NOTE: Be sure the power is off before installing.
1. Attach the light kit to the switch housing by feeding
the light kit wires (black and white) through the hole
of switch housing and then screw it onto the switch
housing by nut & lock washer. Be sure it is tight
enough to prevent light kit from vibrating loose.
(Fig. 1)
2. While holding the light kit assembly under your fan,
snap together the wire connection plugs. (Fig. 2)
3. Carefully push all wires back into the switch
housing, then install the light kit assembly onto the
mounting plate with 3 screws provided. Be sure to
tighten all screws.
4. Install 3 x 60W candelabra bulbs (included). (Fig. 2)
5. Remove the metal nut, glass cap and decorative nut
from the light kit. Place globe over the light kit stem,
secure with the metal nut, glass cap and decorative
nut. Do not overtighten. (Fig. 2)
6. Turn the power on. Your Regency Ceiling Fan is now
ready to enjoy!
11
Nut
Switch Housing
Light Kit
Lock Washer
Fig. 1
Fig. 2
Wire Connection
Plugs
Light Kit
Screws
Bulbs
Globe
Mounting
Plate
Metal Nut
Glass Cap
Decorative Nut

OPERATION
Turn on the power and check operation of the fan. The fan is controlled by the use of the pull chain as follows:
one pull = high speed
two pulls = medium speed
three pulls = low speed
four pulls = off
For proper functions, ensure that the chain is pulled down fully and released each time.
NOTE:
NOTE:
Leave pull chain switch in "high speed" position when using optional wall control.
The slide switch on the side of the switch housing controls forward or reverse rotation. Make sure switch is not stuck
between forward and reverse positions.
IMPORTANT:
IMPORTANT:
To prevent damage or cause injury, be sure that fan is switched to off and blades have stopped moving
completely before attempting to change direction of rotation.
Forward/Reverse Direction:
Warm Weather (forward):
A DOWNWARD airflow creates a cooling effect as shown in Figure 1. This allows you to set your air conditioner on a
warmer setting without affecting your comfort.
Cool Weather (Reverse):
An UPWARD airflow moves warmer air off the ceiling area as shown in Figure 2. This allows you to set your heating
unit on a cooler setting without affecting your comfort.
12
Fig. 1 Fig. 2

CARE AND CLEANING
Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking
or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges.
When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades.
If you experience any flaws in the operation of your fan, please check the following points.
TROUBLESHOOTING - INCASE OF DIFFICULTY
CAUTION:
CAUTION:
Switch off power supply before carrying out any of these checks.
1. If fan will not start: Check main and branch circuit breakers and/or fuses. Check line wire connections to fan housing
wiring. Make sure forward/reverse switch is set to one or the other position, not stuck in between.
2. If fan is noisy: Check and make sure that all screws in motor housing are snug (but not over tight). Check that the
screws securing blade arms to the motor are tight. Check that wire connectors in switch housing are not rattling
against each other or the interior wall of the switch housing. Check that all glassware is finger tight and that bulb(s)
are well held in the sockets, if a light kit is used. Check that the canopy is firmly attached to hanging bracket and not
vibrating against ceiling.
3. If fan wobbles: Check that all blades are firmly screwed into blade arms. Check that all blade arms are firmly secure to
the motor. Check to make sure that light kit (if present) is firmly attached to switch housing and that all glassware
and shades are fastened properly. Wobble can also result from even the smallest deviations in distance from blade tip
to blade tip. If measurements from blade tip to blade tip are not equal, loosen screws connecting blade to blade arm
one at a time and adjust blade(s) so that distances are equal. Interchanging adjacent blades may redistribute mass and
result in smoother operation. Blade arms can be bent slightly to restore same pitch to all blades if a blade is different
than the other blades when viewed edge on. Most wobble can be traced to a loose electrical box or mounting bracket.
Make sure these are tight and the ball is completely seated in the bracket.
13
THANK YOU FOR PURCHASING A REGENCY CEILING FAN.
Write to us at:
Regency Ceiling Fans
P.O. Box 730
Fenton, MO 63026
Visit us on the Web at: www.regencyfan.com
12/22 Regency Ceiling Fans