Regency Quatro User manual

• QUATRO •
• CEILING FAN OWNER'S MANUAL •
WARNING: Read and follow these instructions carefully and be mindful of all warnings shown throughout.
10/09
Style that revolves around you.

GENERAL INSTALLATION & OPERATION INSTRUCTIONS
IMPORTANT SAFEGUARDS:
1. To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly
To ensure the success of the installation, be sure to read the instructions and review the diagrams thoroughly
before beginning.
before beginning.
2. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All
electrical connections must be made in accordance with local codes, ordinances and/or the National Electric
Code. If you are unfamiliar with the methods of installing electrical wiring and products, secure the services of a
qualified and licensed electrician as well as someone who can check the strength of the supportive ceiling
members and make the proper installation(s) and connections.
3. Make sure that your installation site will not allow rotating fan blades to come in contact with any object. Blades
should be at least 7 feet from floor.
4. When mounting on a ceiling outlet box, an approved box UL listed as "suitable for fan support"
"suitable for fan support"
is required. The
box and its supporting members must be able to support the moving weight of the fan's listed weight. The box
must not be able to twist or work loose. Installation on a concrete ceiling should be performed by qualified
personnel.
5. Blades should be attached after motor housing is hung and in place. Fan motor housing should be kept in the
carton until ready to be installed to protect its finish. If you are installing more than one ceiling fan, make sure
that you do not mix fan blade sets
do not mix fan blade sets
, as each blade is part of a weighted set.
6. After making electrical connections, spliced conductors should be turned upward and pushed carefully up into
outlet box. The wires should be spread apart with the common conductor and the grounding conductor on one
side of the outlet box, and the "HOT" wires on the other side.
7. Electrical diagrams are for reference only.
8. After fan is completely installed, check to make sure that all connections are secure to prevent fan from falling
and/or causing damage or injury.
9. The fan can be made to work immediately after installation - the bearings are adequately charged with grease so
that, under normal conditions, further lubrication should not be necessary for the life of the fan.
10. Do not operate the reverse switch while the fan blades are in motion. The fan must be turned off and the blades
stopped before reversing the blades direction.
Notice:
Notice:
This appliance is equipped with a "Wattage Limiting Device" required by the United States Department of
Energy. The device has been installed at the factory and can not be removed. Installing Lamps in excess of 190 total
watts will disable the unit's light fixture. If this should happen, you will need to reset the lighting fixture by turning
the power off to the ceiling fan and/or light fixture, reinstalling lamps totaling less that 190 watts and then turning
the power back on.
1
Weight of Fan: 20.30 Lbs

IMPORTANT SAFETY PRECAUTIONS
2
Thank you for choosing a Regency Ceiling Fan. You have chosen the best!
Your new ceiling fan has been designed to provide many years of service and enjoyment.
• Disconnect power by removing fuse or turning off circuit breaker before installing the fan.
Disconnect power by removing fuse or turning off circuit breaker before installing the fan.
• Support directly from building structure.
• To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked "acceptable for fan
"acceptable for fan
support"
support"
and use mounting screws provided with the outlet box. Most outlet boxes commonly used for the support
of lighting fixtures are not acceptable for fan support and may need to be replaced. Consult a qualified electrician if
in doubt.
• Do not use an incandescent light dimmer. Do not use this fan with any transformer type fan speed control device.
• To reduce the risk of fire, electrical shock, or personal injury, only use this fan with an appropriate speed control
device designed for use with ceiling fans if you choose a wall control.
• To reduce the risk of personal injury, do not bend the blade arms when installing them, balancing the blades or
cleaning the fan. Do not insert any objects(s) between rotating fan blades.
NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all
NOTE:The important precautions, safeguards and instructions appearing in this manual are not meant to cover all
possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness
possible conditions and situations that may occur. It must be understood that common sense, caution and carefulness
are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring
are factors which cannot be built into this product. These factors must be supplied by the person(s) installing, caring
for, and operating the unit.
for, and operating the unit.
Warnings:
Warnings:
TOOLS AND MATERIALS REQUIRED
• Phillips screwdriver
• Blade screwdriver
• Wrench or pliers
• Wire cutter
• Stepladder
• Wiring supplies as required by
electrical code

UNPACKING YOUR FAN
1. Unpack your fan and check the contents. Do not discard the carton. If warranty replacement or repair is ever
necessary, the fan should be returned in original packing. Remove all parts and hardware. Do not lay motor
housing on its side, or the decorative housing may shift, be bent or damaged.
2. Examine all parts. You should have the following:
1. Fan blades (5)
2. Hanging bracket
3. Ceiling canopy
4. Canopy screw cover plate
5. Downrod/ball assembly
6. Decorative collar cover
7. Fan motor assembly
8. Light plate
9. Globe
10. Receiver+6 wire nuts
11. Transmitter incl. holder + 2 mounting screws
12. 100W Halogen bulb
13. Optional light cover for non light use.
14. Bracket mounting hardware (wood screws, screws, lock washers, washers, wire nuts)
15. Blade to blade arm screws, w/washers (13)
NOTE:
NOTE:
Design of parts shown above may look slightly different for your specific model of fan.
3
1
26
8
7
9
14
15
10
11
13
12
4
5
3

PREPARATION
PREPARATION:
Verify you have all parts before beginning the installation. Check foam insert closely for missing parts. Remove motor
from packing. To avoid damage to finish, assemble motor on soft padded surface or use the original foam inset in motor
box. Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.
Do not lay motor housing on its side as this could result in shifting of motor in decorative enclosure.
Caution:
Caution:
To avoid possible electrical shock, be sure electricity
is turned off at the main power box before wiring. All wiring
must be in accordance with National and Local Electrical
Codes and the ceiling fan must be grounded as a precaution
against possible electric shock.
1. Locate ceiling joist where fan is to be mounted, being sure
location agrees with the requirements in the minimum
clearance section of this guide. Wood joist must be sound
and of adequate size to support 35 lbs. (See Page 1, Items 3
and 4).
2. If not already present, mount a UL listed outlet box marked
"suitable for fan support" following the instructions
provided with the outlet box. The outlet box must be able
to support a minimum of 35 pounds.
3. Attach hanger bracket to outlet box using screws provided
using screws provided
with the outlet box.
with the outlet box.
4
Parts identification on assembled fan
Blades
Collar
Cover
Light Plate
Downrod
Canopy
Globe
INSTALLING THE HANGING BRACKET
Ceiling Fan
Outlet Box
Hanger
Bracket
Outlet Box
Screw
Flat Washer
Spring Washer
Motor
Housing

INSTALLING THE FAN
1. Carefully support fan body (motor) in its styrofoam
packing with the mounting collar (where the wires come
out) facing upward.
2. Loosen the two set screws and remove the downrod pin
and cotter pin from the top coupling of the motor
assembly. (Fig. 1)
3. Remove ball from the downrod by loosening set screw in
the side of the ball. Slide ball down and remove ball pin;
remove ball.
4. Feed the wires from top of fan through end of the downrod
of choice and set end of downrod into mounting collar so
the hole in the downrod lines up with the hole in the side
of the mounting collar.
5. Insert downrod pin through holes in mounting collar and
downrod; slip cotter pin through small hole in end of
downrod pin to hold downrod in place.
6. Tighten jam screws against downrod using a large flat
blade screwdriver to ensure a tight fit against downrod.
Tighten nuts against mounting collar.
NOTE:
NOTE:
Fan has 6 feet of hook-up wire in case you are using
a long extension downrod. Wires can be cut so only 8
inches or so extend beyond the top of the downrod to make
the electrical connections easier and safer.
7. Feed wires through collar cover and slide collar cover
down the downrod to top of fan.
8. Feed wires through canopy screw cover plate and
canopy, then slide both over downrod to lay on top of
collar cover. It will be attached to ceiling later.
9. Feed wires through ball and slide ball over downrod, past
hole in the top end of the downrod. Insert ball pin
(removed in step 3), slide ball up, and tighten set screw
to secure ball in place.
10. Lift ball/downrod/fan into hanging bracket opening.
NOTE:
NOTE:
The tab opposite hanging bracket opening should fit
in slot on ball.
5
Hook-up (3)
Wires
Ground
Wire
Ball
Canopy
Canopy Screw
Cover Plate
Downrod
Mounting Collar
Downrod Pin
Top of
Fan Body
Collar Cover
Security Screws
Cotter
Pin
Fig. 1
Fig. 2
Slot
Tab

ELECTRICAL CONNECTIONS
6
WARNING:
WARNING:
To avoid possible electrical shock, be sure electricity is turned off at the main fuse box before wiring.
Multiple code choices are included with your fan¡¦s remote control in case:
* you have more than one remote control fan and want them to respond only to their own remote control.
*you have other radio controlled devices in your home that may interfere with the fan remote control. (i.e. garage
door opener)
* you experience radio interference on a chosen frequency. (code setting)
* do not use factory codes, change to new settings.
NOTE:
NOTE:
This remote control unit is equipped with 16 code combinations to prevent possible interference from or to
other remote units. The frequency switches on your receiver and transmitter have been preset at the factory. Please
recheck to make sure the switches on transmitter and receiver are set to the same position, any combination of settings
will operate the fan as long as the transmitter and receiver are set to the same position. (Fig. 1)
Step 1. (Fig. 2) Insert the receiver into the mounting bracket with the flat side of the receiver facing the ceiling.
Step 2. (Fig. 3) Motor to Receiver Electrical Connections: Connect the black wire from the fan to black wire marked
"TO MOTOR L". Connect the white wire from the fan to the white wire marked "TO MOTOR N" from the receiver.
Connect the blue wire from the fan to the blue wire marked "For Light" from the receiver. Secure the wire connections
with the plastic wire nuts provided.
Fig. 1 Fig. 2
ON
ON
Code switch
Receiver
Hanger
bracket

ELECTRICAL CONNECTIONS
7
Step 3. (Fig. 3) Receiver to House Supply Wires Electrical
Connections: Connect the black (hot) wire from the
ceiling to the black wire marked "AC in L" from the
receiver. Connect the white(neutral) wire from the ceiling
to the white wire marked "AC in N" from the Receiver.
Secure the wire connections with the plastic wire nuts
provided.
Step 4. (Fig. 3) If your outlet box has a ground wire (green
or bare copper) connect it to the fan ground wires;
otherwise connect the hanging bracket ground wire to the
mounting bracket. Secure the wire connection with a
plastic nut provided. After connecting the wires, spread
them apart so that the green and white wires are on one
side of the outlet box and black and blue wires are on the
other side. Carefully tuck the wire connections up into the
outlet box.
NOTE:
NOTE:
Fan must be installed at a maximum distance of 30
feet from the transmitting unit for proper signal transmission
between the transmitting unit and the fan's receiving unit.
Fig. 3
White (neutral)
White (neutral)
Green or bare
copper (ground)
White ("AC IN N")
White ("to motor N")
Ground
(green)
(Connect to
ground wire on
hanger bracket
if no house
ground wire
exists.)
Outlet box
Black (hot)
Black ("AC IN L")
Black ("to motor L")
Receiver
Blue (for light)
Blue (for light)
Black (motor)

FINISHING THE INSTALLATION
BLADE ATTACHMENT
1. Tuck connections neatly into ceiling outlet box.
2. Slide the canopy up to ceiling and over the 2 screws on
the hanger bracket. Rotate canopy clockwise. Next, while
holding the canopy with one hand, slide the canopy
screw cover plate over the screws and rotate clockwise
until tight. NOTE:
NOTE:
adjust the canopy screws as necessary
until the canopy and canopy screw cover plate are snug.
WARNING:
WARNING:
Make sure the hook on the hanging bracket
properly sits in the groove in the hanger ball before
attaching the canopy to the bracket by turning the housing
until it drops into place.
Step 1. Insert the blade through the blade slot in the
decorative housing. Align the holes in blade and blade arm,
place the blade arm plate on blade as showing in Figure 12,
making sure the holes are also aligned and secure with lock
washers and screws provided.
Step 2. Repeat process with other blades.
NOTE:
NOTE:
Cordless power screwdrivers are NOT
NOT
recommended,
as they tend to strip the heads of the screws and usually will
not fully compress the lock washers on the motor screws. Use
a large flat blade screwdriver for final tightening to fully
compress the washers. This will help ensure proper alignment
of the blades and noise-free, wobble-free running.
8
Canopy
Screws
Canopy Screw
Cover Plate
Ceiling Fan
Outlet Box
Hanger
Bracket
Blade
Slot
Screws

INSTALLATION THE MONTING PLATE
1. Remove one of the three screws on the mounting hub located on the fan motor.
2. Loosen the other two screws.
3. Install light plate to mounting hub.
4. Line up the two slotted holes with the two loose screws on the mounting hub located on fan motor.
5. Re-install the third screw removed and tighten all three.
9
INSTALLING THE LIGHT PLATE
Light plate
Mounting Hub
(bottom of motor)
Screws

INSTALLING THE LIGHT BULB AND GLOBE
NOTE: Be sure the power is off before installing.
NOTE: Be sure the power is off before installing.
NOTE:
NOTE:
IF YOU DO NOT PLAN TO INSTALL THE LIGHT KIT WITH YOUR FAN AT THIS TIME, THEN GO
STRAIGHT TO STEP 2.
1. Install 100W Halogen bulb (included).
2. Raise the bottom globe up against light plate and secure it to fan by twisting glass clockwise until snug. DO NOT
OVERTIGHTEN. Note:
Note:
If installing the optional light cover, make sure is securely tighten.
3. Restore power and your light kit is ready for operation.
10
Globe
Bulb
Light plate

OPERATING YOUR WALL TRANSMITTER
11
9 Volt
Battery
Restore power to ceiling fan and test for proper operation.
Install 9 Volt battery (not included). To prevent damage to transmitter remove
the batteries if not used for long periods of time. (Fig. 1)
1. "LO, MED, HI" buttons:
These three buttons are used to set the fan speed as follows:
LO= Low speed MED= Medium speed
HI= High speed
2. "FAN/OFF" button:
This button turns the fan off.
3. The " LIGHT" button are controlled by pressing the light button. Tap button
quickly to turn light off or on. Push the button once and release to turn the
light on to full brightness. Hold the button down to increase or decrease
light brightness. Release the button at the desired light brightness and that
setting will be remembered the next time the light is turned on. The pre-set
brightness can be changed by holding down the light button again until the
new desired brightness is reached.
NOTE:
NOTE:
If power is lost to the fan receiver, the memory will be lost and all
settings will return to the default.
4. "FOR/REV" button:
This button is used to change the direction of the rotation of the blades;
forward for warm weather or reverse for warm weather.
Fig. 1
Fig. 2

12
INSTALLING THE TRANSMITTER HOLDER
1. Attach the holder with the two screws provided.
Holder
Screws
Fig. 3 Fig. 4
Speed settings for warm or cool weather depend on factors such as the room size, ceiling height, number of fans, etc.
NOTE:
NOTE:
To operate the reverse function on this fan, press the "FOR/REV" button while the fan is running.
Warm weather-(Counter-Clockwise direction) A downward air flow creates a cooling effect.(Fig. 3) This allows you
to set your air conditioner on a higher setting without affecting your comfort.
Cool weather-(Clockwise direction) An upward airflow moves warm air off the ceiling area.(Fig. 4) This allows you
to set your heating unit on a lower setting without affecting your comfort.
NOTE:
NOTE:
Range of the transmitter is approximately 25 ft. A new alkaline battery will typically give range of 35 ft. or more.

CARE AND CLEANING
Periodically it may be necessary to re-tighten blade to blade arm screws or blade arm to motor screws to prevent clicking
or humming sound during operation. This is especially true in climates with broad temperature and humidity ranges.
When dusting the blades, you must support the blade to prevent bending - no pressure should be applied to the blades.
If you experience any flaws in the operation of your fan, please check the following points.
TROUBLESHOOTING - INCASE OF DIFFICULTY
CAUTION:
CAUTION:
Switch off power supply before carrying out any of these checks.
1. If fan will not start: Check main and branch circuit breakers and/or fuses. Check line wire connections to fan housing
wiring. Make sure forward/reverse switch is set to one or the other position, not stuck in between.
2. If fan is noisy: Check and make sure that all screws in motor housing are snug (but not over tight). Check that the
screws securing blade arms to the motor are tight. Check that wire connectors in switch housing are not rattling
against each other or the interior wall of the switch housing. Check that all glassware is finger tight and that bulb(s)
are well held in the sockets, if a light kit is used. Check that the canopy is firmly attached to hanging bracket and not
vibrating against ceiling.
3. If fan wobbles: Check that all blades are firmly screwed into blade arms. Check that all blade arms are firmly secure to
the motor. Check to make sure that light kit (if present) is firmly attached to switch housing and that all glassware
and shades are fastened properly. Wobble can also result from even the smallest deviations in distance from blade tip
to blade tip. If measurements from blade tip to blade tip are not equal, loosen screws connecting blade to blade arm
one at a time and adjust blade(s) so that distances are equal. Interchanging adjacent blades may redistribute mass and
result in smoother operation. Blade arms can be bent slightly to restore same pitch to all blades if a blade is different
than the other blades when viewed edge on. Most wobble can be traced to a loose electrical box or mounting bracket.
Make sure these are tight and the ball is completely seated in the bracket.
13
THANK YOU FOR PURCHASING A REGENCY CEILING FAN.
Write to us at:
Regency Ceiling Fans
P.O. Box 730
Fenton, MO 63026
Visit us on the Web at: www.regencyfans.com
10/09 Regency Ceiling Fans