Regency Classic C34 Quick start guide
MODELS: C34-NG10 Natural Gas C34-LP10 Propane
C34 Classic™ Direct Vent
Freestanding Gas Stove
Owners &
Installation Manual
C34 Video
- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch: do not use any phone in your building.
Leave the building immediately.
• Immediately call your gas supplier from a neighbour's phone. Follow the gas supplier's
instructions.
• If you cannot reach you gas supplier, call the fire department.
- Installation and service must be performed by a qualified installer, service agency or the gas supplier.
WARNING
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious
injury, death, or property damage.
Tested by:
Installer: Please complete the details on the back cover
and leave this manual with the homeowner.
Homeowner: Please keep these instructions for future reference.
919-490c FPI FIREPLACE PRODUCTS INTERNATIONAL LTD. 6988 Venture St., Delta, BC Canada, V4G 1H4 09.16.16
2| Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
2
REGENCY
Classic Direct Vent Freestanding Gas Stove
To the New Owner:
Congratulations! You are the owner of a state-of-the-art Gas Stove by Fireplace Products International Ltd. The Regency® Gas Series
-
ment now to acquaint yourself with these instructions and the many features of your CLASSIC Direct Vent Freestanding Gas Stove.
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 3
| 3
This Regency®
This Regency®
to secure the unit.
INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
This Regency®
This appliance installation must comply with the manufacturer's installation instructions and local codes, if any. In the absence of local codes follow the
C34 Video
4| Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
4dimensions
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 5
| 5
table of contents
Installation
For Your Safety ..............................................................8
Important Message ......................................................9
Specifications ................................................................9
General Safety Information............................................9
Installation Checklist....................................................10
Locating Your Gas Stove..............................................10
Manufactured Mobile Home Additional Requirements 10
Combustion and Ventilation Air....................................10
Clearances to Combustibles........................................10
Optional Fan Installation ..............................................11
Pedestal Assembly ......................................................13
Leg and Bottom Shield Assembly................................13
Venting Introduction.....................................................14
Installation Precautions ...............................................14
Safety Precautions for the Installer..............................14
Vent Restrictor Position ...............................................14
Exterior Vent Terminal Locations .................................15
4” x 6-5/8” Rigid Pipe Cross Reference Chart .............16
Rigid Pipe Venting Systems.........................................18
Venting Arrangements ................................................19
Venting Arrangements ................................................19
DV Stove Horizontal Vent Kit .......................................21
Dura-Vent Termination Kit............................................23
Dura-Vent Horizontal Installations ...............................24
Vertical Termination .....................................................25
Cathedral Ceilings .......................................................26
Converting Class-A Metal Chimney or
Direct Vent System ......................................................27
System Data................................................................28
Gas Connection...........................................................28
High Elevation..............................................................28
Gas Pipe Pressure Testing ..........................................28
Log Installation ............................................................30
Door and Glass Frame ................................................30
Safety screen installation / removal .............................31
Door Handle ................................................................31
Remote Control Installation .........................................31
Optional Wall Thermostat ...........................................31
Final Check..................................................................31
Wiring Diagram............................................................32
Pilot Adjustment...........................................................33
Aeration Adjustment ....................................................33
First Fire ......................................................................34
Operating Instructions
Operating Instructions .................................................34
Lighting Procedure ......................................................34
Shutdown Procedure ...................................................34
Copy of the Lighting Plate Instructions .......................35
Normal Operating Sounds of
Gas Appliances ...........................................................36
Thermopile / Thermocouple.........................................36
Maintenance
Maintenance Instructions ............................................36
General Vent Maintenance ..........................................36
Log Replacement ........................................................36
Glass Gasket ...............................................................37
Glass Replacement .....................................................37
Valve Assembly replacement.......................................37
Parts
Main Assembly ............................................................38
Burner Assembly & Log Set ........................................39
Base Options...............................................................40
Warranty
Warranty ......................................................................42
6| Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
6safety decal
This is a copy of the label that accompanies
each CLASSIC Direct Vent Freestanding Gas
Stove. We have printed a copy of the contents
here for your review. The safety label is located
NOTE: Regency® units are constantly being
the correct one.
3
/
:&NSD
:&NSD
:&NSD
PP
%78+NZK
%78+NZK
IWSLP
3523$1(*$66729(0RGHO&/3
/
0LQLPXPVXSSO\SUHVVXUH
0DQLIROGSUHVVXUHKLJK
0DQLIROGSUHVVXUHORZ
2ULILFHVL]H
0LQLPXPLQSXW
0D[LPXPLQSXW
$OWLWXGH
$33$5(,/)21&7,211$17$83523$1(
&21&83285(75(32(/(0RGpOH&/3
3UHVVLRQGDOOLPHQWDWLRQPLQLPXP
3UHVVLRQjODWXEXOXUHG FKDSSHPHQW OHY Hp p p
3UHVVLRQjODWXEXOXUHG FKDSSHPHQWEDVVHp
*UDQGHXUGHOLQMHFWHXU
' ELW&DORULILTXHPLQLPXPVHORQp
' ELW&DORULILTXHPD[LPXPVHORQp
ODOWLWXGH
0RGHO0RGHOH
&/3
3
/
:&NSD
:&NSD
:&NSD
PP
%78+NZK
%78+NZK
IWSLP
1$785$/*$66729(0RGHO&1*
/
0LQLPXPVXSSO\SUHVVXUH
0DQLIROGSUHVVXUHKLJK
0DQLIROGSUHVVXUHORZ
2ULILFHVL]H
0LQLPXPLQSXW
0D[LPXPLQSXW
$OWLWXGH
$33$5(,/)21&7,211$17$8*$=1$785$/
&21&83285(75(32(/(0RGpOH&1*
3UHVVLRQGDOOLPHQWDWLRQPLQLPXP
3UHVVLRQjODWXEXOXUHG FKDSSHPHQW OHY Hp p p
3UHVVLRQjODWXEXOXUHG FKDSSHPHQWEDVVHp
*UDQGHXUGHOLQMHFWHXU
' ELW&DORULILTXHPLQLPXPVHORQp
' ELW&DORULILTXHPD[LPXPVHORQp
ODOWLWXGH
0RGHO0RGHOH
&1*
'2256($/
3OHDVHFKHFNWKDWWKHGRRULVSURSHUO\VHDOHG
0$<%(,167$//(',10$18)$&785('02%,/(+20(6$)7(5),5676$/(
'21275(029(7+,6/$%(/1(3$6(1/(9(5&(77(e7,48(77(
'83/,&$7(6(5,$/12
)3,)LUHSODFH3URGXFWV,QWHUQDWLRQDO/WG
'HOWD%&&DQDGD
0DGHLQ&DQDGD
)DEULTXHDX&DQDGD
0LQLPXP&OHDUDQFHVWR&RPEXVWLEOHV
'HJDJHPHQW0LQLPXP
'H0DWHULDX[&RPEXVWLEOHV
$PP
%PP
(PP
0LQLPXPFHLOLQJKHLJKWIURP
WRSRIXQLWPP
0LQLPXPSODIRQGKDXWHXUHQ
KDXWGHODSSDUHLOPP
0LQLPXPFOHDUDQFHWRYHQW³PP
6HULDO1R1RGHVHULH
3DUW
&RORXU%ODFNRQ*UH\H[FHSWVHOHFWHGWH[WLVLQUHGDVSHUWKLVSULQW
6L]H 3ULQWHGDW
0DWHULDOPOVLOYHUPDWWSRO\HVWHU'30606
'HF&UHDWHGGHFDO
3ULQWHU&RQWLQXHQXPEHUVHTXHQFHIURPGRQRWUHVWDUWDW
%DFNZDOO
6LGHZDOO
(
""
#
%DFNZDOO
6LGHZDOO
6LGHZDOO
7KLVDSSOLDQFHPXVWEHLQVWDOOHGLQDFFRUGDQFHZLWKORFDOFRGHVLIDQ\LIQRQHIROORZWKH1DWLRQDO)XHO*DV&RGH$16,=RU1DWXUDO*DVDQG3URSDQH,QVWDOODWLRQ
&RGH&6$%
7KLVDSSOLDQFHPXVWEHLQVWDOOHGLQDFFRUGDQFHZLWKWKH6WDQGDUG&$1&6$=0+0RELOH+RXVLQJLQ&DQDGDRUZLWKWKH0DQXIDFWXUHG+RPH&RQVWUXFWLRQDQG6DIHW\
6WDQGDUG7LWOH&)53DUWLQWKH8QLWHG6WDWHVRUZKHQVXFKDVWDQGDUGLVQRWDSSOLFDEOH$16,1&6%&6$1)3$$0DQXIDFWXUHG+RPH,QVWDOODWLRQV
6WDQGDUGRU$16,$RX1)3$&6WDQGDUGIRU5HFUHDWLRQDO9HKLFOHV
7KLVDSSOLDQFHLVRQO\IRUXVHZLWKWKHW\SHRIJDVLQGLFDWHGRQWKHUDWLQJSODWHDQGPD\EHLQVWDOOHGLQDQDIWHUPDUNHWSHUPDQHQWO\ORFDWHGPDQXIDFWXUHGPRELOHKRPHZKHUH
QRWSURKLELWHGE\ORFDOFRGHV6HHRZQHUVPDQXDOIRUGHWDLOV2SWLRQDO)DQ.LW3DUW
,QVWDOOHUODSSDUHLOVHORQOHVFRGHVRXUqJOHPHQWVORFDX[RXHQODEVHQFHGHWHOVUqJOHPHQWVVHORQOHVFRGHVGLQVWDOODWLRQ$16,=1DWLRQDO)XHO*DV&RGHRX&6$%
HQYLJXHXU
,QVWDOOHUODSSDUHLOVHORQODQRUPH&$1&6$=6pULH000DLVRQPRELOHVRX&$1&6$=9&9pKLFXOHVGHFDPSLQJRXODQRUPH&)53DUW0DQXIDFWXUHG
+RPH&RQVWUXFWLRQDQG6DIHW\6WDQGDUG6LFHVQRUPHVQHVRQWSDVSHUWLQHQWHVXWLOLVH]ODQRUPH$16,1&6%&6$1)3$$0DQXIDFWXUHG+RPH,QVWDOODWLRQV
6WDQGDUGRX$16,$RX1)3$&6WDQGDUGIRU5HFUHDWLRQDO9HKLFOHV
&HWDSSDUHLOGRLWrWUHXWLOL]HXQLTXHPHQWDYHFOHW\SHGHJD]LQGLTXpVXUODSODTXHVLJQDOpWLTXH&HWDSSDUHLOSHXWrWUHLQVWDOOpGDQVXQHPDLVRQSUpIDEULTXpHRXPRELOHe8
VHXOHPHQWLQVWDOOpHjGHPHXUHVLOHVUqJOHPHQWVORFDX[OHSHUPHWWHQW9RLUODQRWLFHGHOXWLOLVDWHXUSRXUSOXVGHUHQVHLJQHPHQWV&HWDSSDUHLOQHSHXWSDVrWUHXWLOLVpDYHF
GDXWUHVJD]VDXIVLXQHWURXVVHGHFRQYHUVLRQFHUWLILpHHVWIRXUQLH
7KLVYHQWHGJDVILUHSODFHKHDWHULVQRWIRUXVHZLWKDLUILOWHUV1HSDVXWLOLVHUGHILOWUHjDLUDYHFFHIR\HUDXJD]jpYDFXDWLRQ
)RUXVHZLWKJODVVGRRUVFHUWLILHGZLWKWKHDSSOLDQFHRQO\3RXUXWLOLVDWLRQXQLTXHPHQWDYHFOHVSRUWHVHQYHUUHFHUWLILpHVDYHFODSSDUHLO
9(17('*$6),5(3/$&(+($7(5127)2586(:,7+62/,')8(/6
1(3$687,/,6(5$9(&'8&20%867,%/(62/,'()2<(5$8*$=¬e9$&8$7,21
/LVWHG9(17('*$6),5(3/$&(+($7(5)2<(5$8*$=¬e9$&8$7,21
&HUWLILHGIRU&HUWLIL HSRXU&$1$'$DQG86$p
7HVWHGWR&$1&*$05
$16,=&RQIRUPVWR
&6$&HUWLILHGWR
)RU8VH2QO\ZLWK%DUULHU3DUW)ROORZLQVWDOODWLRQLQVWUXFWLRQV8WLOLVHUXQLTXHPHQWDYHFO¶pFUDQQ6XLYUHOHVLQVWUXFWLRQVGLQVWDOODWLRQ
(/(&75,&$/6833/<$/,0(17$7,21(/(&75,48(
9B+=OHVVWKDQPRLQVGH$03
and repair must be done by a plumber or
length.
-
t-handle type valve.
the gas appliance is installed.
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 7
| 7
requirements
5.08: Modifications to NFPA-54, Chapter 10
(2) Revise 10.8.3 by adding the following additional requirements:
(a) For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for
residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than
seven (7) feet above finished grade in the area of the venting, including but not limited to decks and porches, the following requirements shall
be satisfied:
1. INSTALLATION OF CARBON MONOXIDE DETECTORS. At the time of installation of the side wall horizontal vented gas fueled
equipment, the installing plumber or gasfitter shall observe that a hard wired carbon monoxide detector with an alarm and battery back-up is
installed on the floor level where the gas equipment is to be installed. In addition, the installing plumber or gasfitter shallobserve that a battery
operated or hard wired carbon monoxide detector with an alarm is installed on each additional level of the dwelling, building or structure
served by the side wall horizontal vented gas fueled equipment. It shall be the responsibility of the property owner to secure the services of
qualified licensed professionals for the installation of hard wired carbon monoxide detectors
a. In the event that the side wall horizontally vented gas fueled equipment is installed in a crawl space or an attic, the hard wired carbon
monoxide detector with alarm and battery back-up may be installed on the next adjacent floor level.
b. In the event that the requirements of this subdivision can not be met at the time of completion of installation, the owner shall have a period of
thirty (30) days to comply with the above requirements; provided, however, that during said thirty (30) day period, a batteryoperated carbon
monoxide detector with an alarm shall be installed.
2. APPROVED CARBON MONOXIDE DETECTORS. Each carbon monoxide detector as required in accordance with the above provisions
shall comply with NFPA 720 and be ANSI/UL 2034 listed and IAS certified.
3. SIGNAGE. A metal or plastic identification plate shall be permanently mounted to the exterior of the building at a minimum height of eight
(8) feet above grade directly in line with the exhaust vent terminal for the horizontally vented gas fueled heating appliance or equipment. The
sign shall read, in print size no less than one-half (1/2) inch in size, "GAS VENT DIRECTLY BELOW. KEEP CLEAR OF ALL
OBSTRUCTIONS".
4. INSPECTION. The state or local gas inspector of the side wall horizontally vented gas fueled equipment shall not approve the installation
unless, upon inspection, the inspector observes carbon monoxide detectors and signage installed in accordance with the provisions of 248 CMR
5.08(2)(a)1 through 4.
(b) EXEMPTIONS: The following equipment is exempt from 248 CMR 5.08(2)(a)1 through 4:
1. The equipment listed in Chapter 10 entitled "Equipment Not Required To Be Vented" in the most current edition of NFPA 54 as adopted by
the Board; and
2. Product Approved side wall horizontally vented gas fueled equipment installed in a room or structure separate from the dwelling, building or
structure used in whole or in part for residential purposes.
(c) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM PROVIDED. When the manufacturer of Product
Approved side wall horizontally vented gas equipment provides a venting system design or venting system components with the equipment, the
instructions provided by the manufacturer for installation of the equipment and the venting system shall include:
1. Detailed instructions for the installation of the venting system design or the venting system components; and
2. A complete parts list for the venting system design or venting system.
(d) MANUFACTURER REQUIREMENTS - GAS EQUIPMENT VENTING SYSTEM NOT PROVIDED. When the manufacturer of a
Product Approved side wall horizontally vented gas fueled equipment does not provide the parts for venting the flue gases, but identifies
"special venting systems", the following requirements shall be satisfied by the manufacturer:
1. The referenced "special venting system" instructions shall be included with the appliance or equipment installation instructions; and
2. The "special venting systems" shall be Product Approved by the Board, and the instructions for that system shall include a parts list and
detailed installation instructions.
(e) A copy of all installation instructions for all Product Approved side wall horizontally vented gas fueled equipment, all venting instructions,
all parts lists for venting instructions, and/or all venting design instructions shall remain with the appliance or equipmentat the completion of
the installation.
MA Code - CO Detector
(for the State of Massachusetts only)
8| Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
8installation
CLOTHING OR OTHER FLAMMABLE
MATERIAL SHOULD NOT BE PLACED
ON OR NEAR THE APPLIANCE.
CHILDREN AND ADULTS SHOULD BE
ALERTED TO THE HAZARDS OF HIGH
SURFACE TEMPERATURES, ESPE-
CIALLY THE FIREPLACE GLASS, AND
SHOULD STAY AWAYTO AVOID BURNS
OR CLOTHING IGNITION.
INSTALLATION AND REPAIR SHOULD
BE DONE BY AN AUTHORIZED
SERVICE PERSON. THE APPLIANCE
SHOULD BE INSPECTED BEFORE
USE AND AT LEAST ANNUALLY BY A
PROFESSIONAL SERVICE PERSON.
MORE FREQUENT CLEANING MAY
BE REQUIRED DUE TO EXCESSIVE
LINT FROM CARPETING, BEDDING
MATERIAL,ETC.IT IS IMPERATIVETHAT
CONTROLCOMPARTMENTS,BURNERS
AND CIRCULATING AIR PASSAGEWAYS
OF THE APPLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES, THE
APPLIANCE SHOULD BE LOCATED
OUT OF TRAFFIC AND AWAY FROM
FURNITURE AND DRAPERIES.
WARNING: FAILURE TO INSTALL THIS
APPLIANCE CORRECTLY WILL VOID
YOUR WARRANTY AND MAY CAUSE A
SERIOUS HOUSE FIRE.
YOUNG CHILDREN SHOULD BE CARE-
FULLY SUPERVISED WHEN THEY ARE
IN THE SAME AREA AS THE APPLI-
ANCE. TODDLERS,YOUNG CHILDREN
AND OTHERS MAY BE SUSCEPTIBLE
TO ACCIDENTAL CONTACT BURNS. A
PHYSICAL BARRIERS IS RECOMMEND-
ED IFTHERE ARE AT RISK INDIVIDUAL
INTHE HOUSE. TO RESTRICT ACCESS
TO A FIREPLACE OR STOVE, INSTALL
AN ADJUSTABLE SAFETY GATE TO
KEEP TODDLERS, YOUNG CHILDREN
AND OTHER AT RISK INDIVIDUALS OUT
OF THE ROOM AND AWAY FROM HOT
SURFACES.
FOR YOUR SAFETY
This appliance requires air for proper combustion.
Always provide adequate combustion and
ventilation air. Follow instructions and information
requirements for combustion and ventilation air.
ANY SAFETY SCREEN, GUARD, OR
BARRIER REMOVED FOR SERVICING
THE APPLIANCE,MUST BE REPLACED
PRIORTOOPERATINGTHEAPPLIANCE.
IFTHE BARRIER BECOMES DAMAGED,
THE BARRIER SHALL BE REPLACED
WITHTHEMANUFACTURER'SBARRIER
FOR THIS APPLIANCE.
A BARRIER DESIGNED TO REDUCE
THE RISK OF BURNS FROM THE HOT
VIEWING GLASS IS PROVIDED WITH
THIS APPLIANCE AND SHALL BE
INSTALLED FOR THE PROTECTION
OF CHILDREN AND OTHER AT-RISK
INDIVIDUALS
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 9
| 9
installation
IMPORTANT MESSAGE
SAVE THESE
INSTRUCTIONS
The CLASSIC Direct Vent Freestanding Gas Stove
must be installed in accordance with these instruc-
tions. Carefully read all the instructions in this
jurisdiction to determine the need for a permit prior
to starting the installation.
- WARNING -
Failure to follow the instructions could
which could result in death, serious
Failure to follow these instructions
or warranty.
SPECIFICATIONS
Fuels: C34-NG10 is approved for use with natural
gas. C34-LP10 is approved for use with
Electrical:
Optional circulation fan:
Log Sets:
GENERAL SAFETY
INFORMATION
1. The appliance installation must conform with
local codes or, in the absence of local codes,
Codes.
2. The appliance when installed, must be electri-
cally grounded in accordance with local codes,
or in the absence of local codes with the current
3. The appliance should be inspected for shipping
damage before use and serviced annually by
lint from carpeting, bedding material, etc. It
is imperative that control compartments, and
circulating air passageways of the appliance
4. See general construction and assembly in-
structions. The appliance and vent should be
enclosed when installed in or passing through
a living area.
5. This appliance must be connected to the speci-
the building envelope.
6. Never vent to another room or inside a build-
section.
7.
and any signs of deterioration.
8. Venting terminals shall not be recessed into a
wall or siding.
9. Any safety glass removed for servicing must
be replaced prior to operating the appliance.
10 To prevent injury, do not allow anyone who is
SHOULD OVERHEATING OCCUR, OR
THE GAS SUPPLY FAIL TO SHUT OFF,
SHUT OFF THE MANUAL GAS VALVE
TO THE APPLIANCE BEFORE SHUT-
TING OFF THE ELECTRICAL SUPPLY.
- WARNING -
-
nance of this appliance.
1. Provide adequate clearances for servicing,
proper operation and around the air openings
into the combustion chamber.
2.
a platform to enhance its visual impact. If the
appliance is going to be installed on carpeting,
The CLASSIC Direct Vent Freestanding Gas
Stove can be installed in a wide variety of ways
installed in a recessed position, framed out into
the room, or across a corner. This appliance is
Listed for Alcove installations, maintain minimum
Alcove clearances as follows, minimum ceiling
3. The CLASSIC Direct Vent Freestanding Gas
Stove is approved for alcove installations, which
in a bedroom, when installed with a millivolt ther-
mostat. This unit is approved for manufactured
section for the required vent arrangements. If
installed into a manufactured or mobile home
4. We recommend that you plan your installation on
review your plans before installation.
-
fornia to cause cancer, birth defects or other
reproductive harm.
10 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
10 installation
AA
B
Back wall
Back wall
Side wall
Side wall
Side wall
C
D
F
F
E
E
COMBUSTION AND
VENTILATION AIR
The combustion air from this appliance is drawn
from outside the building through the outer
CLEARANCES TO
COMBUSTIBLES
appliance and the chimney connector. The
farthest distance is correct if the two clearances
is set as indicated in one of the diagrams but
This unit can be installed on a solid combustible
installed directly on carpeting or vinyl when the
This appliance may be installed only with the
clearances as shown in the situations pictured.
Do not combine clearances from one type of
installation with another in order to achieve
closer clearances.
INSTALLATION
CHECKLIST
1. Locate your appliance. Refer to the following
a. Locating Your Classic Gas Stove
b. Clearances to Combustibles
sections.
2.
3. Assemble stove base - pedestal or bottom
4. Choose a venting option and Install
accordingly. Refer to the following sections
c. Vent Restrictor setting
System.
5.
section.
6. Install 4-AA batteries into receiver. This will
enable operation of appliance manually when
7.
8. Install standard and optional features. Refer
a. Log Installation
b. Door and Glass Frame
d. Safety Screen
e. Remote Control
f. Wall Thermostat
9.
-
customer.
This includes:
1.
2. If required, adjusting the primary air to ensure
3.
CAUTION: Any alteration to the product that
causes sooting or carboning that results in dam-
age is not the responsibility of the manufacturer.
LOCATING YOUR
GAS STOVE
When selecting a location for your stove, ensure
that the clearances on this page are met as well
as ensuring that there is adequate accessibility
for servicing and proper operation.
MANUFACTURED
MOBILE HOME
ADDITIONAL
REQUIREMENTS
1.
2.
3.
sections.
top of unit.
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 11
| 11
installation
OPTIONAL FAN INSTALLATION
C34
09.16.16919-512a
Diagram 5
9. Slide thermodisc under the thermodisc bracket.
1. Open pedestal door and remove door cover plate by removing 4 screws.
See Diagram 3.
2. Remove valve cover plate by removing 2 screws.
3. Remove wire from receiver.
4. Screw the four screws provided into the nutserts as shown in Diagram 5.
Do not tighten screws.
5. Place the fan assembly partially in door cover plate hole. See Diagram 4.
6. Attach the 2 ground wires (green) to the ground lug as per Diagram 4.
OPTIONAL FAN INSTALLATION
Diagram 3
Diagram 1
Remove 7 screws on top
Loosen 4 screws on bottom–
slide access panel to the right
to remove
Diagram 2
Loosen 7 screws–slide access
panel to
the front of unit to remove
Leg unit: Loosen 7 screws on bottom access panel–slide panel toward the
front to remove.
IMPORTANT Disconnect power supply before servicing
Pedestal unit: To install the fan in an installed stove-access from front through
the pedestal by following the directions below. If the stove is not
installed - access through the back - open back as shown below.
Note: Ground lug is located on the bottom of the fan assembly. See
Diagram 4.
7. Lift the fan assembly in through the pedestal and up through the cut out
as shown in Diagrams 5 and 6.
8. Place the insulation gasket on the back of the fan. Line up the keyhole
slots with the matching screws and pull back slightly to lock into place.
While holding fan assembly in place, tighten screws.
Diagram 6
Diagram 4
120 Volt AC power is needed for the fan. The fan can be hard wired if
desired. The outlet should be installed in the receptacle box on the left
hand side by a qualified electrician. The neutral (wider) slot of the polarized
outlet should be at the top.
7KHUPRGLVF
%UDFNHW
7KHUPRGLVF
Diagram 7
12 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
12 installation
C34
09.16.16
919-512a
Caution: Ensure that the wires do not
touch any hot surfaces.
FAN REMOVAL
1. Disconnect the power to the fan.
2. Allow the stove to cool to room temperature.
3. Open the pedestal door and remove the screws on the door cover plate.
(Leg units: remove the bottom access panel.)
4. Unplug the fan from the FCM.
5. Loosen the screws of the nutserts.
6. Remove the fan assembly from the key slots at the fan base and pull fan
out through the rectangular opening. (Diagram 5).
7. Turn fan 90 degrees. (Diagram 5). (Pedestal units only).
8. Disconnect the green ground wires to the grounding lug.
9Remove fan from stove. (Diagram 3)
IMPORTANT:
THESE FANS COLLECT A LOT OF
DUST FROM WITHIN YOUR HOME.
ENSURE YOU MAINTAIN THESE FAN
MOTORS ON A REGULAR BASIS BY
VACUUMING THE FAN BLADES AND
THE HOUSING WITH A SOFT BRUSH
NOZZLE.
Note: The #8 ground lug is a dedicated ground for mobile home
use only.
10. Install the FCM (fan control module) to the fl oor of the pedestal or bottom
heat shield with supplied magnets. Connect the FCM power cord to the
supplied extension cord and then run extension cord out the back of the
unit. See below.
11. Plug the fan into the FCM.
Use strain relief grommet when running extension cord
through Pedestal
Run the extension cord through the largest opening at
the back when using the Bottom Heat Shield with Legs
option–no strain relief grommet required.
Diagram 8
Diagram 10
Diagram 9
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 13
| 13
installation
PEDESTAL ASSEMBLY
1.
2.
corners of the pedestal top with the corresponding holes in the base of
in diagram. Reinstall bolts.
3. Push the Regency® logo into the two holes in the front bottom left corner
of the pedestal cover plate.
LEG AND BOTTOM SHIELD ASSEMBLY
These instructions apply to the steel leg and painted cast leg. It will be easier
1. Remove the 4 bolts in the underside of the base and discard.
2.
leg, then slide the bottom shield in between the leg and the base of the
stove. Tighten the bolts.
3. Level the stove by adjusting the levelling
bolts in the bottom of each leg.
Note: Any paint touch up should be done
prior to placing logo on pedestal.
14 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
14 installation
INSTALLATION
PRECAUTIONS
These venting systems are engineered products
that have been designed and tested for use with
the C34-NG10 and the C34-LP10. The warranty will
1. Installation of any damaged Direct Vent com-
ponent
2.
System
3. Installation of any component part not manu-
factured or approved by Simpson Dura-Vent or
Fireplace Products International Ltd.
4. Installation other than as instructed by Simpson
Dura-Vent and Fireplace Products International
Ltd.
-
spaces with insulation.
section and in your local building codes.
separate solid fuel or gas-burning appliance.
separate vent system. Common vent systems are
prohibited.
SAFETY
PRECAUTIONS
FOR THE INSTALLER
1. Wear gloves and safety glasses for protection.
2.
or on roof tops.
3.
and ceilings.
VENTING INTRODUCTION
-
son Dura-Vent Direct Vent venting systems,
in combination with the Classic Direct Vent
Freestanding Gas Stove, C34-NG and C34-LP,
have been tested and listed as direct vent heater
of combustion to the outside while the outer pipe
draws outside combustion air into the combus-
tion chamber thereby eliminating the need to
use heated room air for combustion and losing
warm room air up the chimney.
-
nected to any other appliance.
The gas appliance and vent system must be
vented directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
separate vent system. Common vent systems
are prohibited.
IMPORTANT
Read all instructions carefully before starting
the installation. Failure to follow these instruc-
venting and clearance to combustible require-
ments. Consult your local building codes before
beginning installation.
The location of the termination cap must conform
VENT RESTRICTOR
POSITION
Vent restriction is required for certain venting
required for your installation.
Simply loosen the screws and push the vent
restrictor plate to the correct position. Tighten
the screws.
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 15
| 15
installation
EXTERIOR VENT TERMINAL LOCATIONS
Minimum Clearance Requirements Canada1USA2
AClearance above grade, veranda, porch, deck, or balcony 12"(30cm) 12"(30cm)
BClearance to window or door that may be opened 12"(30cm) 9" (23cm)
CClearance to permanently closed window * *
DVertical clearance to ventilated soffit located above the terminal within a horizontal distance of 2 feet (61cm)
from the center line of the terminal (check with the local code)
18"(46cm) 18"(46cm)
EClearance to unventilated soffit 12"(30cm) 12"(30cm)
FClearance to outside corner: with AstroCap Termination Cap. 6"(15cm) 6"(15cm)
Clearance to outside corner: with all other approved Termination Caps. 12"(30cm) 12"(30cm)
GClearance to inside corner: with AstroCap Termination Cap 6"(15cm) 6"(15cm)
Clearance to inside corner: with all other approved Termination Caps. 12"(30cm) 12"(30cm)
HClearance to each side of center line extended above meter/regulator assembly 36"(90cm)a*
JClearance to service regulator vent outlet 36"(90cm) *
KClearance to non-mechanical air supply inlet to building or the combustion air inlet to any other appliance 12"(30cm) 9" (23cm)
LClearance to a mechanical air supply inlet (91cm) above if within 10' (3m) horizontally. 72"(1.8m) 36"(90cm)b
MClearance above paved sidewalk or a paved driveway located on public property 84"(2.1m)*
NClearance under veranda, porch, deck, or balcony 12"(30cm)‡*
1In accordance with current CSA B149.1, Natural Gas and Propane Installation Code
2In accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code
A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings
‡ Permitted only if veranda, porch, deck, or balcony is fully open on a minimum of two sides beneath the floor
*Clearance in accordance with local installation codes and the requirements of the gas supplier
a3 feet (91cm) within a height of 15 feet (4.5m) above the meter / regulator assembly
b3 feet (91cm) above - if within 10 feet (3m) horizontally
16 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
16 installation
4” X 6-5/8” RIGID PIPE CROSS REFERENCE CHART
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
6” Pipe Length-Galvanized 46DVA-06 4DT-6 N/A 4D6 SV4L6 TC-4DL6
6” Pipe Length-Black 46DVA-06B 4DT-6B N/A 4D6B SV4LB6 TC-4DL6B
7” Pipe Length-Galvanized N/A N/A 4D7 N/A N/A N/A
7” Pipe Length-Black N/A N/A 4D7B N/A N/A N/A
9” Pipe Length-Galvanized 46DVA-09 4DT-9 N/A N/A N/A TC-4DL9
9” Pipe Length-Black 46DVA-09B 4DT-9B N/A N/A N/A TC-4DL9B
12” Pipe Length-Galvanized 46DVA-12 4DT-12 4D12 4D12 SV4L12 TC-4DL1
12” Pipe Length-Black 46DVA-12B 4DT-12B 4D12B 4D12B SV4LB12 TC-4DL1B
18” Pipe Length-Galvanized 46DVA-18 4DT-18 4D18 4D18 SV4LA TC-4DL18
18” Pipe Length-Black 46DVA-18B 4DT-18B 4D18B 4D18B SV4LA TC-4DL18B
24” Pipe Length-Galvanized 46DVA-24 4DT-24 4D24 4D24 SV4L24 TC-4DL2
24” Pipe Length-Black 46DVA-24B 4DT-24B 4D24B 4D24B SV4LB24 TC-4DL2B
36” Pipe Length-Galvanized 46DVA-36 4DT-36 4D36 4D36 SV4L36 TC-4DL3
36” Pipe Length-Black 46DVA-36B 4DT-36B 4D36B 4D36B SV4LB36 TC-4DL3B
48” Pipe Length-Galvanized 46DVA-48 4DT-48 4D48 4D48 SV4L48 TC-4DL4
48” Pipe Length-Black 46DVA-48B 4DT-48B 4D48B 4D48B SV4LB48 TC-4DL4B
60” Pipe Length-Galvanized 46DVA-60 4DT-60 N/A N/A N/A N/A
60” Pipe Length-Black 46DVA-60B 4DT-60B N/A N/A N/A N/A
Adjustable Length 3”-10”-Galvanized N/A N/A N/A 4DAL N/A TC-4DLT
Adjustable Length 3”-10”-Black N/A N/A N/A 4DALB N/A TC-4DLTB
Adjustable Length 7”-Galvanized N/A N/A 4D7A N/A N/A N/A
Adjustable Length 7”-Black N/A N/A 4D7AB N/A N/A N/A
Extension Pipe 8-1/2”-Galvanized 46DVA-08A N/A N/A N/A N/A N/A
Extension Pipe 8-1/2”-Black 46DVA-08AB N/A N/A N/A N/A N/A
Adjustable Length 12”-Galvanized N/A N/A 4D12A N/A SV4LA12 TC-4dLSI
Adjustable Length 12”-Black N/A N/A 4D12A N/A SV4LBA12 TC-4dLSIB
Extension Pipe 16”-Galvanized 46DVA-16A N/A N/A N/A N/A N/A
Extension Pipe 16”-Black 46DVA-16AB N/A N/A N/A N/A N/A
45ºElbow-Galvanized 46DVA-E45 4DT-EL45 4D45L N/A N/A TE-4DE45
45ºElbow-Black 46DVA-E45B 4DT-EL45B 4DT-EL45B N/A N/A TE-4DE45B
45ºElbow Swivel-Galvanized See 46DVA-E45 N/A N/A 4D45L SV4E45 N/A
45ºElbow Swivel-Black See 46DVA-E45B N/A N/A 4D45LB SV4EB45 N/A
90ºElbow-Galvanized 46DVA-E90 4DT-EL90S 4DT-EL90S N/A N/A TE-4DE90
90ºElbow-Black 46DVA-E90B 4DT-EL90SB 4DT-EL90SB N/A SV4EBR90-1 TE-4DE90B
90ºElbow, Swivel-Galvanized See 46DVA-E90 N/A N/A 4D90L SV4E90-1 N/A
90ºElbow, Swivel-Black See 46DVA-E90B N/A N/A 4D90LB SV4EB90-1 N/A
90º Starter Elbow, Swivel-Galvanized N/A N/A N/A 4D90A N/A N/A
Adaptor* N/A N/A N/A 4D90L N/A N/A
4” X 6- 5/8” RIGID PIPE CROSS REFERENCE CHART
Components from different Manufacturers may not be mixed. Not all rigid pipe components are available directly from Regency.
Note: The listed manufacturers may have other lengths not shown on this chart, which would also be approved.
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
Ceiling Support N/A 4DT-CS 4DSP 4DFSP SV4SD TM4-RDS
Cathedral Support Box 46DVA-CS 4DT-CSS 4DRSB 4DRS SV4CSB TM4-SDS
Wall Support/Band 46DVA-WS 4DT-WS/B 4DWS 4DWS SV4BM TM-SWS
Offset Support46DVA-ES - N/A from FPI 4DT-OS N/A N/A SV4SU TM-SOS
Wall Thimble-Black 46DVA-WT 4DT-WT 4DWT 4DWT SV4RSM N/A
Wall Thimble Support/Ceiling Support 46DVA-DC N/A N/A N/A SV4PF N/A
Firestop Spacer 46DVA-FS 4DT-FS 4DFSP 4DFS SV4BF TM-4CS
Tr im Plate-Black N/A 4DT-TP 4DFPB 4DcP SV4LA TM-4TP
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 17
| 17
installation
Description Simpson
Direct Vent Pro®
Selkirk
Direct Temp™
American Metal
Products®
Amerivent Direct
Metal-Fab™
Sure Seal
Security
Secure- Vent®
ICC Excel
Direct
Attic Insulation Shield 12” 46DVA-IS N/A@ FPI N/A 4DAIS12 N/A SV4RSA N/A
Attic Insulation Shield - Cold Climates 36” N/A N/A 4DAIS12 N/A N/A TM-4AS
High Wind Vertical Cap 46DVA-VCH N/A N/A N/A N/A TM-4VT
High Wind Horizontal Cap 46DVA-HC N/A N/A N/A N/A TM-4DHT
Horizontal Square Te rmination Cap See 46DVA-HC 4DT-HHC 4DHC 4DHT SV4CHC-1 TM-4HT
Vertical Te rmination Cap 46DVA-VC 4DT-HVC 4DVC 4DVT SV4CGV-1 N/A
Storm Collar 46DVA-08A 4DT-SC 4DSC 4DSC SV4FC TM-SC
Restrictor Disk N/A N/A N/A N/A N/A TM-4DS
Extended Vertical Te rmination Cap N/A N/A N/A N/A N/A N/A
Chimney Conversion Kit A (USA only) 46DVA-KCA N/A N/A N/A N/A TM-4CA6
Chimney Conversion Kit B (USA only) 46DVA-KCB N/A N/A N/A N/A TM-4CA7
Chimney Conversion Kit C (USA only) 46DVA-KCC N/A N/A N/A N/A TM-4CA8
Chimney Conversion Kit Masonry
(USA only)
46DVA-KMC N/A N/A N/A N/A N/A
Wall Firestop 46DVA-WFS N/A N/A N/A N/A TM-4TR
Colinear Flex Connectors 46DVA-ADF N/A N/A N/A N/A N/A
Adjustable Flashing 0/12-6/12 46DVA-F12 4DT-ST14 4D12S 4DST14 SV4STC14 TF-4FA
Adjustable Flashing 6/12-12/12 46DVA-F12 4DT-ST36 4D36S 4DST36 SV4STC36 TF-4FB
Vinyl Siding Standoff 46DVA-VSS 4DT-VS N/A 4DVS SV4VS TM-VSS
Vinyl Siding Shield Plate N/A 4DT-VSP N/A N/A SV4VS N/A
Snorkel Te rmination 14” 46DVA-SNKL N/A N/A N/A N/A TM-4ST14
Snorkel Te rmination 36” N/A N/A N/A N/A N/A TM-4ST36
Basic Horizontal Te rmination Kit (A) Disc. 4DT-HKA 4DHTK2 4DHTKA SV-SHK TM4-HTK
Horizontal Te rmination Kit (B) 46DVA-KHA
(Changed Components)
4DT-HKB 4DHTK1 4DHTKB SV-HK TM4-HTK
Vertical Te rmination Kit Disc. 4DT-VKC 4DHTK 4DHTK SV-FK N/A
FPI
946-506/P Vent Guard (Optional) for AstroCap 946-205 Vinyl Siding Shield for Riser Vent Te rminal
510-994 Rigid Pipe Adaptor (Must use with all rigid piping) 946-208/P Vent Guard (Optional) for Riser Vent Te rminal
640-530/P Riser Vent Te rminal 946-523/P AstroCap Horizontal Cap
946-206 Vinyl Siding Standoff for AstroCap
Note: When using Metal-Fab Sure Seal Rigid Piping - please note that the Adaptor (4DDA) must be used in conjunction with FPI Rigid Pipe Adaptor (510-994).
Note: Horizontal runs of vent must be level, or have a 1/4” rise for every 1 foot of run towards the termination.
Never allow the vent to run downward - this could cause high temperatures and may present a possible fi re hazard.
Offset Pipe Selection: Use this table to determine offset pipe lengths.
Pipe Length
(L)
4” x 6-5/8” Venting For specific instructions on venting components - visit the
manufacturers website listed below.
Run (X) Rise (Y)
0” (0mm) 4-7/8” (124mm) 13-7/8” (340mm) Simpson Direct Vent Pro: www.duravent.com
6” (152mm) 8” (203mm) 16-1/2” (419mm) Selkirk Direct-Temp: www.selkirkcorp.com
9” (229mm) 10-1/8” (257mm) 18-5/8” (473mm) American Metal Products: www.americanmetalproducts.com
12” (305mm) 12-1/4” (311mm) 20-3/4” (527mm) Metal-Fab Sure Seal: www.mtlfab.com
24” (610mm) 20-5/8” (524mm) 29-1/8” (740mm) Security Secure Vent: www.securitychimneys.com
36” (914mm) 29” (737mm) 37-1/2” (953mm) Industrial Chimney Company: www.icc-rsf.com
48” (1219mm) 37-7/16” (951mm) 45-15/16” (1167mm)
Regency Fireplace Products . 6988 Venture St. . Delta, BC . Canada . V4G 1H4 . 604-946-5155 . www.regency-fire.com
18 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
18 installation
Pipe Length
Vertical
Termination
Cap
Storm Collar
Flashing
Ceiling Firestop
24" Pipe
Length
Adj.Pipe Length
11"-14-5/8"
90 Elbow
o
Horizontal
Termination Cap
# 946-523/P
Wall Thimble
Vinyl Siding
Standoff (Optional)
RIGID PIPE VENTING SYSTEMS
Horizontal or Vertical Terminations
Alternate
Horizontal
Termination
Caps
Temp, Ameri Vent Direct venting and Security
Secure Vent systems.
WARNING:
Do not combine venting components from
and FPI
Riser is acceptable with all systems.
When using Rigid Vent other than
used to secure rigid pipe to unit.
The FPI AstroCap® Direct Vent, Ameri-
®
Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove | 19
| 19
installation
VENTING ARRANGEMENTS
VERTICAL TERMINATION SYSTEMS FOR
RESIDENTIAL MANUFACTURED AND MO-
BILE HOMES
-
o elbows.
Venting Arrangements Examples:
VENTING ARRANGEMENTS
HORIZONTAL TERMINATIONS FOR ALL
VENTING SYSTEMS
-
one 90O elbow (two 45o o elbow).
Propane and Natural Gas: Residential, Manufactured
and Mobile Homes Installations
NOTE: See "Vent Restrictor Position" section for installation instructions for the Vent Restrictor Position.
use Vent Restrictor Position "R" (Right)
20 | Regency® CLASSIC™ C34-10 Direct Vent Freestanding Gas Stove
|
20 installation
Horizontal Venting with Two (2. 90oElbows
Option V H + H1
Vertical Venting with Two (2. 90oElbows
Option V H V + V1
pipe length is 30 feet with min.
Please note min. 1 foot
between 90o elbows is
required.
pipe length is 30 feet with minimum
Please note minimum 1 foot be-
tween 90o elbows is required.
One 90o elbow = Two 45o elbows.
One 90o elbow = Two 45o elbows.
Lengths do not include elbow
indicated.
Lengths do not include elbow indicated.
Other manuals for Classic C34
4
Table of contents
Other Regency Stove manuals
Regency
Regency Ultimate U39E Series Quick start guide
Regency
Regency C33-LP3 Quick start guide
Regency
Regency Ultimate U38-LP1 User manual
Regency
Regency ULTIMATE U38E Quick start guide
Regency
Regency F37-LPG Quick start guide
Regency
Regency ULTIMATE U38-LP Quick start guide
Regency
Regency F38NG2-BRA Quick start guide
Regency
Regency ULTIMATE U38 Quick start guide
Regency
Regency Hampton GC60-2 User manual
Regency
Regency F33NG3-RA Quick start guide
Regency
Regency Ultimate U38-NG1 Quick start guide
Regency
Regency ULTIMATE U43-NG User manual
Regency
Regency ULTIMATE U41FS-NG User manual
Regency
Regency ULTIMATE U41FS-LP User manual
Regency
Regency Ultimate U39EX Quick start guide
Regency
Regency U39-NG11 Quick start guide
Regency
Regency Vancouver F2402M Quick start guide
Regency
Regency Ultimate U39E-NG12 Quick start guide
Regency
Regency FG39-NG1 Quick start guide
Regency
Regency Ultimate U39 Quick start guide
Popular Stove manuals by other brands
Procom
Procom PCSD25T user manual
Haas+Sohn
Haas+Sohn HSP 6 PALLAZZA-III 519.08 Equipment sheet
Evonicfires
Evonicfires Compton 2 instruction manual
Heat & Glo
Heat & Glo TIARAI-BK-IPI installation manual
WANDERS
WANDERS STEALTH - SCHEMATICS manual
United States Stove Company
United States Stove Company KING KP5513 Owner’s Instruction and Operation Manual
Nordpeis
Nordpeis ME Pedestal Installation and user manual
Firewarm
Firewarm 4KW Insert Installation and operating instructions
MCZ
MCZ DECO' AIR 8 M1 Use and installation manual
Mareli Systems
Mareli Systems ONYX AIR 8 KW Assembly and exploitation manual
Vermont Iron
Vermont Iron The Elm owner's manual
Pellet Fire Solutions
Pellet Fire Solutions Ravelli Natural 7 Owners & installation manual