Regency FireGenie FG39NG1-BRA Quick start guide

December 20 2016
FOR YOUR SAFETY
What to do if you smell gas:
Do not try to light any appli-
ance
Do not touch any electri-
cal switch: do not use any
phone in your building.
Immediately call your gas
supplier from a neighbour's
phone. Follow the gas sup-
plier's instructions.
If you cannot reach your
gas supplier, call the re
department.
WARNING:
Improper installation, adjustment, altera-
tion, service or maintenance can cause
injury or property damage. Refer to this
manual. For assistance or additional in-
formation consult an authorized installer,
service agency or the gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other am-
mable vapours and liquids in the vicinity of
this or any other appliance.
Installation and service must be performed
by an authorized installer, service agency or
the gas supplier.
PLEASE KEEP THESE INSTRUCTIONS
FOR FUTURE REFERENCE
Owners &
Installation
Manual
LISTINGS AND CODE APPROVALS
These gas appliances have been tested in
accordance with AS4553, NZS 5262 and
have been certied by the Australian Gas
Association for installation and operation
as described in these Installation and
Operating Instructions.
Your unit should be serviced annually
by an authorised service person.
918-646f
Models: FG39NG1-BRA
FG39LPG1-BRA
Freestanding Gas Stove

2Regency FG39-1 FireGenie Freestanding Gas Stove
To the New Owner:
Congratulations! You are the owner of a state-of-the-art Regency Room Sealed Gas Stove by FPI Fireplace
Products International Ltd. The Regency Gas Series of hand crafted appliances has been designed to provide
you with all the warmth and charm of a woodstove. The models FG39NG1-BRA and FG39LPG1- BRA of this
series has been approved by AGA. As it also bears our own mark, it promises to provide you with economy,
comfort and security for many trouble free years to follow. Please take a moment now to acquaint yourself
with these instructions and the many features of your Regency Room Sealed Freestanding Gas Stove.

Regency FG39-1 FireGenie Freestanding Gas Stove 3
UNIT SPECIFICATIONS

4Regency FG39-1 FireGenie Freestanding Gas Stove
TABLE OF CONTENTS
Operating Instructions
Operating Instructions ............................................24
Lighting Instructions................................................24
Resetting the Unit ...................................................24
Shutdown Instructions ............................................24
First Fire .................................................................24
Fan Operation.........................................................24
Adjusting Flame Height ..........................................24
Summary of Controls ..............................................25
Pilot Adjustment ......................................................25
Normal Operating Sounds of Gas Appliances .......25
Copy of Lighting Plate Instructions .........................26
Maintenance
Maintenance Instructions........................................27
Log Replacement ...................................................27
Door Gasket ...........................................................27
Latch Adjustment ....................................................27
Glass Replacement ................................................28
Fan Maintenance ...................................................28
Removing Valve Tray ..............................................29
Parts List
Electronic Components ..........................................30
Main Assembly .......................................................31
Burner and Log Assembly ......................................32
Door Assembly .......................................................33
Warranty
Warranty .................................................................34
Safety Label
Safety Label............................................................. 5
Installation
Specications ...........................................................3
Before You Start .......................................................6
General Safety Information.......................................6
Installation Checklist .................................................7
Clearances to Combustibles.....................................7
Locating Your Regency Gas Stove ...........................7
Combustion and Ventilation Air.................................7
Louver Installation ....................................................8
Flueing Introduction ..................................................8
Installation Precautions ............................................8
Safety Precautions for the Installer...........................8
Exterior Flue Termination Locations .........................9
Flueing Arrangements - Horizontal
Terminations: All Systems ................................10
Flueing Arrangements - Vertical Terminations ........10
- Straight Vertical ..............................................10
- O󰀨set Vertical.................................................10
Flue Restrictor Position ..........................................10
DV Stove Horizontal Flue Kit ................................ 11
Dura-Flue Termination Kit .......................................13
Planning Your Dura-Flue Installation ......................13
Dura-Flue Fluing Components Parts List ...............13
Dura-Flue Horizontal Installation ............................14
Dura-Flue Vertical Termination Installation .............15
O󰀨set Chart ............................................................16
Cathedral Ceiling Installations ................................16
Support Extension - Round or Square....................16
Gas Connection ......................................................17
Gas Pipe Pressure Testing .....................................17
Valve Description ....................................................17
Aeration Adjustment ...............................................17
System Data Chart .................................................17
Conversion from NG to LPG...................................18
Log Installation .......................................................20
Front Door Installation ............................................22
Optional Remote Control .......................................22
Final Check.............................................................22
Wiring Diagram .......................................................23

Regency FG39-1 FireGenie Freestanding Gas Stove 5
SAFETY LABEL
This is a copy of the label that accompanies each
REGENCY FG39 Freestanding Gas Stove. We
have printed a copy of the contents here for your
review. The data plat is located on the inside of
the drop down pedestal door.
NOTE: Regency units are constantly being
improved. Check the label on the unit and if
there is a di󰀨erence, the label on the unit is the
correct one.
(Australia Only)
Gas Type NG LPG
Model FG39NG1-BRA FG39LPG1- BRA
Gas Consumption 40mj. 38mj.
Manifold Pressure .94kPa 2.55kPa
Injector Size 1x#32 1x#50
Part #: 918-279d
Colour: Black on Silver
Size: 100%
Sept. 22/09: updated standard (removed 2000 from As4553)
Feb. 4/10: updated distributor
Dec. 23/13: Updated distributor address E. Aus + reformatted
AGA approval.
June 14/16: Updated model name as per Dave L
Electrical:240VAC50Hz1.0ampmax.
Serial
Number
918-279d
Model
N2134
Regency Gas Fireplace
2.95mm 1.78mm
Approval No. AGA 6240 G
Code AS4553
261
Distributed by:
Western Australia:
Air Group Australia
28 Division St
Welshpool, WA 6106
Eastern Australia
Fireplace Products
Australia Pty. Ltd.
1 Conquest Way
Hallam, VIC 3803
To be installed by an authorised person in
accordance with installation instructions
provided with the appliance.

6Regency FG39-1 FireGenie Freestanding Gas Stove
IMPORTANT:
SAVE THESE
INSTRUCTIONS
The REGENCY Room Sealed Freestanding
Gas Stove must be installed in accordance
AG601 and NZS 5261 and with these instruc-
tions. Carefully read all the instructions in this
manual rst. Consult the building authority
having jurisdiction to determine the need for a
permit prior to starting the installation.
Note: Failure to follow the instructions
could cause a malfunction of the
heater which could result in death,
serious bodily injury, and/or property
damage. Failure to follow these
instructions may also void your re
insurance and/or warranty.
Note: These instructions take precedence
over Simpson Dura-Flue instruc-
tions.
SPECIFICATIONS
Fuels: FG39NG1-BRA is approved for use with
NG.
FG39LPG1-BRA is approved for use
with liqueed petroleum gases (LPG).
Electrical: 240V A.C. system.
Circulation Fan: Variable speed, 125/75.
Log Sets: Ceramic bre, 7 per set.
Flue System: Coaxial (6-5/8" outer / 4" inner
liner) rigid ue and termination cap.
BEFORE YOU START
Safe installation and operation of this appliance
requires common sense, however, we are
required by the Canadian Safety Standards
and ANSI Standards to make you aware of
the following:
INSTALLATION
LINT FROM CARPETING, ETC.
IT IS IMPERATIVE THAT THE
CONTROL COMPARTMENT,
BURNERS AND CIRCULATING
AIRPASSAGEWAYSOF THEAP-
PLIANCE BE KEPT CLEAN.
DUE TO HIGH TEMPERATURES,
THE APPLIANCE SHOULD BE
LOCATEDOUTOFTRAFFICAND
AWAY FROM FURNITURE AND
DRAPERIES.
WARNING:FAILURETOINSTALL
THIS APPLIANCE CORRECTLY
WILL VOID YOUR WARRANTY
AND MAY CAUSE A SERIOUS
HOUSE FIRE.
CHILDRENANDADULTSSHOULD
BEALERTED TO THE HAZARDS
OF HIGH SURFACE TEMPERA-
TURES,ESPECIALLY THE FIRE-
PLACE GLASS, AND SHOULD
STAY AWAY TO AVOID BURNS
OR CLOTHING IGNITION.
YOUNG CHILDREN SHOULD
BE CAREFULLY SUPERVISED
WHEN THEY ARE IN THE SAME
ROOM AS THE APPLIANCE.
CLOTHING OR OTHER FLAM-
MABLEMATERIALSHOULDNOT
BE PLACED ON OR NEAR THE
APPLIANCE.
INSTALLATION AND REPAIRS
SHOULD BE DONE BY AN AU-
THORIZED SERVICE PERSON.
THISAPPLIANCESHOULDBEIN-
STALLED,REPAIRED,INSPECT-
ED BEFORE USEAND AT LEAST
ANNUALLY BY AN AUTHOR-
IZED SERVICE PERSON. MORE
FREQUENT CLEANING MAY BE
REQUIRED DUE TO EXCESSIVE
page 6. This unit is approved for manufac-
tured home installations, see page 9 for the
required ue arrangements. If installed into a
manufactured home the unit must be bolted
down to the oor.
4) This appliance is Listed for bedroom instal-
lations when used with a Listed Millivolt
Thermostat. Some areas may have further
requirements, check local codes before
installation.
5) This appliance is Listed for Alcove installa-
tions, maintain minimum Alcove clearances
as follows, minimum width of 48" (1219mm),
a maximum depth of 36" (914mm), and
minimum ceiling height of 64"(1626mm).
6) We recommend that you plan your instal-
lation on paper using exact measurements
for clearances and oor protection before
actually installing this appliance. Have an
authorized building inspector review your
plans before installation.
GENERAL SAFETY
INFORMATION
1) The appliance shall be installed in accord-
ance with the manufacturer's installation
instructions,local gas tting regulations,
municipal building codes, water supply
regulations, electrical wiring regulations, with
AS5601-2004 (AGA gas installation code)
NZS 5261 (New Zealand)
2) Installation and repair should be done
ONLY by an authorised person.
3) DO NOT CONNECT TO MASONARY
FLUE.
4) This appliance must be connected to the
specied ue and termination cap to the
outside of the building envelope. Never
ue to another room or inside a building.
Make sure that the ue is tted as per
Flueing instructions.
5) Inspect the ueing system annually for block-
age and any signs of deterioration.
6) Flueing terminals shall not be recessed into
a wall or siding.
7) Any safety glass removed for servicing must
be replaced prior to operating the appli-
ance.
8) To prevent injury, do not allow anyone who
is unfamiliar with the operation to use the
replace.
9) Wear gloves and safety glasses for protection
while doing required maintenance.
1) Provide adequate clearances for servicing,
proper operation and around the air openings
into the combustion chamber.
2) The appliance may be installed on a at,
solid, continuous surface (e.g. wood, metal,
concrete). This may be the oor, or it can be
raised up on a platform to enhance its visual
impact. The appliance may be installed on
carpeting, tile, wood ooring or other com-
bustible material, because the appliance's
metal pedestal base extends the full width
and depth of the appliance. The Regency
Room Sealed Freestanding Gas Stove can
be installed in a wide variety of ways and will
t nearly any room layout. It may be installed
in a recessed position, framed out into the
room, or across a corner.
3) The Regency Room Sealed Freestanding
Gas Stove is approved for alcove installa-
tions, which meet the clearances listed on

Regency FG39-1 FireGenie Freestanding Gas Stove 7
INSTALLATION
2) If required, adjusting the primary air to ensure
that the ame does not carbon. First allow
the unit to burn for 15-20 min. to stabilize.
CAUTION: Any alteration to the product that
causes sooting or carboning that results
in damage is not the responsibility of the
manufacturer.
CLEARANCES TO
COMBUSTIBLES
The clearances listed are MINIMUM distances.
Measure the clearance to both the appliance and
the chimney connector. The farthest distance is
correct if the two clearances do not coincide.
For example, if the appliance is set as indicated
in one of the gures but the connector is too
close, move the stove until the correct clearance
to the connector is obtained.
This appliance may be installed only with the
clearances as shown in the situations pictured.
Do not combine clearances from one type of
installation with another in order to achieve
closer clearances.
This unit can be installed on a solid combustible
surface like a wood oor. This unit can also be
installed directly on carpeting or vinyl when
the bottom pedestal cover plate (provided with
unit) is installed.
Use the minimum clearances shown in the
diagrams below:
FG39NG1 BRA & FG39LPG1-BRA
Clearances
A Side Wall to Unit 190 mm
B Back Wall to Unit 150 mm
E Side Wall to Unit 50 mm
10) Be aware of electrical wiring locations in
walls and ceilings when cutting holes for
termination.
11) Under no circumstances should this ap-
pliance be modied. Parts that have to be
removed for servicing should be replaced
prior to operating this appliance.
12) Installation and any repairs to this appliance
should be done by an authorised service
person. An authorised service person should
be called to inspect this appliance annually.
Make it a practice to have all of your gas
appliances checked annually.
13) Do not slam shut or strike the glass door.
14) Under no circumstances should any solid
fuels (wood, paper, cardboard, coal, etc.)
be used in this appliance.
15) The appliance area must be kept clear and
free of combustible materials, (gases and
other ammable vapours and liquids).
INSTALLATION
CHECKLIST
1) Check Clearances to Combustibles, location
of unit and uing requirements.
2) Install Louvers.
3) Install uing, either with the DV Stove Hori-
zontal Flue Kit or the Dura-Flue Termination
kits. Set Flue Restrictors.
4) Make gas connections. Test the pilot. Must
be as per diagram.
5) If necessary, convert to LPG or convert to
lower Btu rating.
6) Test Gas Pressure.
7) Install log set.
8) Install Front Door Front.
9) Install optional Remote Control.
10) Final check.
Before leaving this unit with the customer, the
installer must ensure that the appliance is r-
ing correctly and operation fully explained
to customer.
This includes:
1) Clocking the appliance to ensure the correct
ring rate (rate noted on label) after burning
appliance for 15 minutes.
FG39NG1-BRA & FG39LPG1-BRA
Reference Dimensions
C Back Wall to Flue Centerline 11" / 280 mm
D Side Wall to Flue Centerline 521 mm
F Side Wall to Flue Centerline 280 mm
Minimum ceiling
height is 914 mm
from top of unit.
LOCATING YOUR
REGENCY GAS STOVE
When selecting a location for your stove, ensure
that the clearances listed above are met as well
as ensuring that there is adequate accessibility
for servicing and proper operation.
A) Cross Corner
B) Room Divider
C) Island
D) Flat on Wall
E) Flat on Wall Corner
F) Flush with Wall/ Alcove
For Flue Termination requirements, see page 8.
COMBUSTION AND
VENTILATION AIR
The combustion air from this appliance is drawn
from outside the building through the outer ue.
Extra provision for combustion air inside the
room is not required.
12’ (4m)
A
C
D
E
F
B
12’ (4m)
Max.
Max.

8Regency FG39-1 FireGenie Freestanding Gas Stove
LOUVER
INSTALLATION
1) Attach the top & bottom louvres to the
side stove panel using 2 screws per
side.
INSTALLATION
FLUEING
INTRODUCTION
The DV Stove Horizontal Flue Kit and the Simp-
son Dura-Flue Room Sealed System Model
DV-GS uing systems, in combination with
the Regency Room Sealed Freestanding Gas
Stove, FG39NG1-BRA, and FG39LPG1-BRA,
have been tested and listed as direct ue heater
systems by AGA.
These units use the "balanced ue" technology
Co-Axial system. The inner liner ues products
of combustion to the outside while the outer pipe
draws outside combustion air into the combus-
tion chamber thereby eliminating the need to
use heated room air for combustion and losing
warm room air up the chimney.
Note: These ue pipes must not be con-
nected to any other appliance.
The gas appliance and ue system must be
ueed directly to the outside of the building,
and never be attached to a chimney serving a
separate solid fuel or gas burning appliance.
Each direct ue gas appliance must use it's own
separate ue system. Common ue systems
are prohibited.
IMPORTANT
Read all instructions carefully before starting the
installation. Failure to follow these instructions
may create a re or other safety hazard, and will
void the warranty. Be sure to check the uing
and clearance to combustible requirements.
Consult your local building codes before begin-
ning installation.
The location of the termination cap must conform
to the requirements in the Exterior Flue Termina-
tion Locations diagram on page 8.
INSTALLATION
PRECAUTIONS
These uing systems are engineered products
that have been designed and tested for use with
the FG39NG1-BRA, and FG39LPG1-BRA. The
warranty will be voided and serious re, health
or other safety hazards may result from any of
the following actions:
1) Installation of any damaged Room Sealed
component
2) Unauthorized modication of the Room
Sealed System
3) Installation of any component part not manu-
factured or approved by Simpson Dura-Flue
or FPI Fireplace Products International
Ltd.
4) Installation other than as instructed by
Simpson Dura-Flue and FPI Fireplace
Products International Ltd.
Warning: Always maintain required
clearances (air spaces) to nearby
combustibles to prevent a fire
hazard. Do not ll air spaces with
insulation.
Be sure to check the ue termination clearance
requirements from decks, windows, so󰀩ts,
gas regulators, air supply inlets and public
walkways as specied in the Exterior Flue
Terminal Locations on page 8 and in your local
building codes.
The gas appliance and ue system must be
ueed directly to the outside of the building,
and never be attached to a chimney serving
a separate solid fuel or gas-burning appli-
ance. Each direct ue gas appliance must use
it's own separate ue system. Common ue
systems are prohibited.
SAFETY
PRECAUTIONS FOR
THE INSTALLER
1) Wear gloves and safety glasses for protec-
tion.
2) Exercise extreme caution when using
ladders or on roof tops.
3) Be aware of electrical wiring locations in
walls and ceilings.

Regency FG39-1 FireGenie Freestanding Gas Stove 9
INSTALLATION
EXTERIOR FLUE TERMINATION LOCATIONS
Minimum clearances required for balanced ue terminals or
the ue terminals of outdoor appliances according to
AS5601-2004 (AGA gas installation code) or NZS 5261 (New Zealand)
Minimum
Clearance (mm)
a Below eaves, balconies or other projections:
- Appliances up to 50 MJ/h input 300
- Appliances over 50 MJ/h input 500
b From the ground or above a balcony 300
c From a return wall or external corner 500
d From a gas meter (M) 1000
e From an electricity meter or fuse box (P) 500
f From a drain or soil pipe 150
g Horizontal from any building structure (unless appliance is approved
for closer installation) or obstruction facing a terminal 500
h From any other ue terminal, cowl or combustion air intake 500
j Horizontally from an openable window, door, or non-mechanical air inlet, or
any other opening into a building, with the exception of sub-oor ventilation
(see also Note (I)):
- Appliances up to 150 MJ/h input 500
- Appliances over 150 MJ/h input 1500
k Vertically below an openable window, door, or non-mechanical air inlet,
or any other opening into a building, with the exception of sub-oor ventilation
(see also Note (I)): see table below
Clearance 'k' in mm
Space Heaters All Other Appliances
Up to 50 MJ/h Up to 50 MJ/h input Over 50 MJ/h input Over 150 MJ/h input
input to 150 MJ/h input
150 500 1000 1500
NOTES:
(I) For mechanical air inlets, including spa blowers, the clearance 'j' and 'k' shall be 1500 mm in all cases.
(II) All distances shall be measured vertically or horizontally along the wall to a point in line with the nearest par to of the terminal.
(III) Prohibited area below electricity meter or fuse box extends to ground level.
(IV) A ue terminal of this type shall not be located under a roofed area unless the roofed area is fully open on at least two sides and
a free ow of air at the appliance is achieved.

10 Regency FG39-1 FireGenie Freestanding Gas Stove
INSTALLATION
FLUEING ARRANGEMENTS
Vertical Terminations Using
Dura-Flue Fluing System for
Residential Manufactured and Mobile Homes
The shaded area in the diagram below shows all allowable combi-
nations of straight vertical and o󰀨set to vertical runs with vertical
terminations. Maximum two 45oelbows.
If the ue is ENCLOSED in a chase (min. size 9" x 9" / 229mm x 229mm)
maintain a 1-1/4" (32mm) clearance to combustibles.
May be installed in Manufactured (Mobile) Homes after rst sale.
Horizontal Terminations for All Fluing Systems
The shaded areas in the diagram below show all allowable combina-
tions of vertical runs with horizontal terminations. Maximum one
90Oelbow (two 45o elbows equal one 90oelbow).
LPG and NG:
Residential, Manufactured and Mobile Homes
Installations
The uing arrangements diagrammed below, have a min. of 75% (ue
loss) e󰀩ciency with Fan O󰀨, as required for manufactured homes. (Actual
e󰀩ciency may be as high as 85%)
May be installed in Manufactured (Mobile) Homes after rst sale.
Flue Restrictor Position
To set the Flue restriction as indicated in the diagram, simply loosen the
screws and push the ue restrictor plate to the correct position. Tighten
the screws.
Flue Restrictor setting at
40 Mj/h
Flue Restrictor setting at
31 Mj/h

Regency FG39-1 FireGenie Freestanding Gas Stove 11
INSTALLATION
DV STOVE HORIZONTAL FLUE KIT (#946-112) INSTALLATION
Minimum Installation Height: FG39: 59-3/4" ( 1518mm)
Review the following sequence of instructions
which are typical of most installations. The
sequence may vary depending on wall thick-
ness. Refer to ue location and clearance
dimensions.
1) Set the unit in its desired location. Check
to determine if wall studs will be in the way
of the uing system, adjust location until
all clearances are met and there are no
obstructions.
Note: A 1-1/2"(38mm) clearance around
the outer pipe must be maintained
except that only a 1" (25mm) clear-
ance is needed at the termination
end.
IMPORTANT:
Do not locate termination hood where
excessive snow or ice buildup may occur.
Be sure to check ue termination area after
snow falls, and clear to prevent accidental
blockage of uing system. When using
snow blowers, make sure snow is not di-
rected towards ue termination area.
2) Assemble a trial t to determine the vertical
center-line for the ue termination.
a) Cut a 241mm round hole on both the
interior and exterior wall.
b) Attach the 2 ft. (.6m) pipe section
to the ue terminal and slide into
position from the exterior. The larger
diameter end of the adjustable pipe
goes to the ue terminal.
c) Install the 90o elbow onto the adjust-
able pipe to determine the vertical
centerline of the starter collar on the
unit.
Note: if the centerline cannot be
met, the adjustable sections will
have to be cut.
DV STOVE HORIZONTAL FLUE KIT
Horizontal Stove Flue Kit (Part # 946-112) includes all the parts needed to install the FG39 Free-
standing Gas unit with minimum horizontal and vertical vent dimensions. For installations that
require longer vertical and/or horizontal vents use the Dura-Vent system as shown in your manual.
Qty. Description
1) 2 Rigid Pipe Section 1.2m length, 165mm inside diameter
2) 1 Flex Liner, compressed aluminium 2 ply liner, 102mm inside diameter
3) 4 spring spacers
4) 1 90 deg. Elbow
5) 1 Decorative Wall Trim
6) 1 Adapter
7) 1 AstroCap Termination Cap
8) 2 Trim Collar
9) 1 tube of Mill-Pac, high temperature sealant
10) 12 Screws, #8 x 1/2" (13mm) Self tapping, Stainless Steel
11) 14 Screws, #8 x 1/2" (13mm) Self tapping, Black
12) 4 Screws #8 x 1-1/2" (38mm) Drill Point, Stainless Steel
Optional:
946-206 Vinyl Siding Stando󰀨 for AstroCap
Note:
a) Liner sections should be continuous
without any joints or seams.
b) This is an approved system, therefore
components in this system must not be
substituted for any other manufacturer's
products.
c) Wall Thimble is required when installing
through a combustible wall.

12 Regency FG39-1 FireGenie Freestanding Gas Stove
INSTALLATION
Outside Wall
Mur extérieur
Furring
Strips
Fourrures en bois
Furstrp.eps
see also c34020a.eps
furstrpf.eps
french
d) Cut the 2 ft. (.6m) section of rigid pipe
to length. Ensure that the pipe length
when cut will seat onto both the starter
collar and the 90o elbow. Crimped
section of rigid pipe seats into the
90oelbow. Only cut the uncrimped
side of pipe.
Dismantle all pipe sections including ue
terminal.
3) Attach the 4" (102mm) dia. ex liner to the
ue terminal ensuring that the ex overlaps
the collar of the ue terminal by a minimum
of 1-3/8"(35mm). Use Mill-Pac to seal and
secure with 3 of the #8 x 1/2" (13mm) screws
(stainless steel).
4) Attach the 2 ft. (.6m)pipe section to the ue
terminal using Mill-Pac and/or high tempera-
ture silicone and attach with 3 of the #8 x
1/2" (13mm) screws (stainless steel).
6) A bead of non-hardening mastic should be
run around both the termination and vinyl
siding stando󰀨 to prevent water from entering
and to make a tight seal between the cap
and the stando󰀨.
7) Stretch the 4" (102mm) dia. ex liner out
fully and get a trial t of the liner onto the
4" (102mm) dia. starter collar.
8) Cut the 4" (102mm) dia. ex liner to the
desired size.
Hint: leave an extra 12" to 16" (305mm to
406mm) of length, this will make the nal
assembly easier to work with.
9) Secure the 4" (102mm) dia. ex liner to the 4"
(102mm) adapter with Mill-Pac and 3 of the
#8 x 1/2" (13mm) screws (stainless steel).
10) Slide the Decorative Wall Cover over the
pipe sections.
11) Slide the 90o elbow (crimp end up) and the
2 ft. (.6m) pipe section (crimp end up) over
the 4" dia. ex liner.
12) Slide the trim collar over the pipe section to
cover the joint.
13) Install the spring spacers onto the pipe
sections.
14) Secure the 4" (102mm) dia. ex liner with
adapter onto the stove collar. Put a bead of
Mill-Pac around the appliance adapter and
secure with 3 screws (#8 x 1/2" / 13mm,
stainless steel).
15) Attach the pipe section onto the starter
collar by sealing with Mill-Pac and/or high
temperature silicone and securing with 3 of
the #8 x 1/2" (13mm) (black) screws. Pipe
seams should be facing the wall.
16) Attach the 90o elbow onto the pipe section by
sealing with Mill-Pac and/or high tempera-
ture silicone and securing with 3 of the #8
x 1/2" (13mm) screws (black).
17) Slide the 2 ft. (.6m) pipe section onto the 90o
elbow. The ex may have to be compressed
back in order for the pipe to properly mate
to the elbow. Seal with Mill-Pac and/or high
temperature silicone and secure with 3 of
the #8 x 1/2" (13mm) screws (black). Pipe
seams facing down.
18) Install the trim collar over the starter collar
and secure with a #8 x 1/2" (13mm) screw
(black).
If the pipe needs to be touched up, use only
Stove Brite High Temperature Metallic Black
Stove Paint.
NOTE: All inner joints must be sealed with
Mill-Pac.
All outer joints may be sealed with
high temperature silicone.
Note: The pipe seam should be facing
down.
Note: To make the installa-
tion more aestheti-
cally pleasing, we
recommend framing
out a square that the
cap can be mounted
on.
Note: If installing termination on a siding
covered wall, a vinyl siding stando󰀨 or
furring strips must be used to ensure
that the termination is not recessed
into the siding. For vinyl siding stand-
o󰀨 installation refer to the Dura-Flue
Termination instructions.
5) Slide the partially connected pipe and ue
terminal assembly through the wall (from
the exterior into the interior) and secure the
cap to the exterior wall with 4 of the supplied
screws (#8 x 1-1/2" (38mm) drill point, stain-
less steel).
Note: The four screws provided for the
ue cap should be replaced with ap-
propriate fasteners for stucco, brick,
concrete, or other types of sidings.
Hint: Apply the
sealant (Mill-
Pac and/or high
temperature
silicone) to the
outer pipe be-
fore connecting
the inner pipe.
#8x½" (13mm) Self Tapping, Stainless Steel
#8x½" Self Tapping, Black(13mm)
#8x1½" (38mm) Drill Point, Stainless Steel

Regency FG39-1 FireGenie Freestanding Gas Stove 13
DURA-FLUE
TERMINATION KIT
Planning Your Dura-Flue
Installation
There are two basic types of Dura-Flue Room
Sealed System installations: horizontal termi-
nation and vertical termination. Conrm the
maximum horizontal run and maximum vertical
rise from the diagrams on page 9.
When planning your installation, it will be nec-
essary to select the proper length of ue pipe
for your particular requirements. For horizontal
installations, determine the minimum clearance
from the rear of the unit to the wall. It is also
important to note the wall thickness. (The wall
thimble is suitable for 2 x 4 or 2 x 6 / .6m x 1m or
.6m x 2m wall construction.) Select the amount
of vertical rise desired for "vertical-to-horizontal"
type installations.
Warning: Always maintain required clear-
ances (air spaces) to nearby combustibles
to prevent a re hazard. Do not ll air spaces
with insulation.
The minimum clearance requirements between
the outer wall of the ue pipe and nearby com-
bustible surfaces is 32mm. Be sure to check
the ue termination clearance requirements
from decks, windows, so󰀩ts, gas regulators, air
supply inlets and public walkways as specied
in the Exterior Flue Termination Locations on
page 8 and in your local building codes.
To determine the length of ue pipe required
for vertical installations, measure the distance
from the unit ue outlet to the ceiling, the ceiling
thickness, the vertical rise in an attic or second
storey, and allow for su󰀩cient vertical height
above the roof line.
For multi-storey applications, re stops are
required at each oor level. If an o󰀨set is
needed, additional pipe, elbows and supports
will be required.
Do not exceed the maximum number of elbows.
One 90o for horizontal terminations and two 45o
for vertical termination.
DURA-FLUE FLUING
COMPONENTS
You will require the following components with
your new Regency Room Sealed Freestand-
ing Gas Stove. Please review your product to
make sure you have everything you need. In
the eue that you are missing any part, contact
your dealer.
Note: These are the minimum pieces re-
quired. Other parts may be required
for your particular installation. See
below for a list of ue parts.
If installing termination on a siding covered wall,
a vinyl siding stando󰀨 or furring strips can be
used in order to ensure that the termination is
not recessed into siding.
The vinyl siding stando󰀨 is required for walls
with vinyl siding.
Minimum components for a Dura-Flue
Horizontal Installation:
A) Dura-Flue Horizontal Termination Kit
B) Wall Thimble (required for combus-
tible walls)
Minimum components for a Dura-Flue
Vertical Termination:
C) Dura-Flue Vertical Termination Kit
The Simpson Dura-Flue Room Sealed System
o󰀨ers a complete line of component parts for
installation of both horizontal and vertical installa-
tion. Many items are o󰀨ered in decorative black,
as well as galvanized nish. The galvanized pipe
and ttings are used for concealed locations such
as attics or where corrosion is a factor, such as
INSTALLATION
above the roof line. Decorative brass trim kits
are available for both wall thimbles and ceiling
support boxes.
Part # Description
971 Horiz. Termination Kit includes:
90o
black elbow, wall thimble cover,
horiz. square termination cap,
24"
black pipe, 11" -14" 5/8" adjust
able
black pipe
970 Basic Horiz. Termination Kit
includes: 90o black elbow, wall
thimble cover, horiz. square
termination cap
978 Vert. Termination Kit includes
0/12 - 6/12 pitch adjustable
ashing, storm collar, low prole
term. cap
908B 6" (152mm) Pipe Length-Black
907B 9" (229mm) Pipe Length-Black
906 12" (304mm) Pipe Length Galv.
906B 12" (304mm) Pipe Length-Black
904 24" (610mm) Pipe Length Galv.
904B 24" (610mm) Pipe Length-Black
903 36" (914mm) Pipe Length Galv.
903B 36" (914mm) Pipe Length-Black
902 48" (1219mm) Pipe Length Galv.
902B 48" (1219mm) Pipe Length-Black
911B 11"-14 5/8" (219mm - 372mm)
Adj. Pipe Length-Black
917B 17"- 24" (432mm - 610mm)
Adj. Pipe Length Black
945 45O Elbow Galv.
945B 45O Elbow-Black
945G 45O Elbow-Swivel Galv.
Dura-Flue Basic
Horizontal Kit # 970
1 90oElbow
1 Wall Thimble Cover
1 Astro Cap

14 Regency FG39-1 FireGenie Freestanding Gas Stove
Diagram 5
Note: If installing termination on a siding covered
wall, a vinyl siding stando󰀨 or furring strips
must be used to ensure that the termination
is not recessed into the siding. The four
wood screws provided should be replaced
with appropriate fasteners for stucco, brick,
concrete, or other types of sidings.
5) Before connecting the horizontal run of ue
pipe to the ue termination, slide the black
decorative wall thimble cover over the ue
pipe, then slide the Wall Thimble (Part #
942) over the ue pipe.
6) Slide the appliance and ue assembly
towards the wall carefully inserting the
ue pipe into the ue cap assembly. It is
important that the ue pipe extends into the
ue cap a su󰀩cient distance so as to result
in a minimum pipe overlap of 1-1/4 inches
(32mm) . Secure the connection between
the ue pipe and the ue cap using sheet
metal screws provided. See diagram 6.
FG39: 59-3/4" (1518mm)
Diagram 2
b) The location of the horizontal ue termi-
nation on an exterior wall must meet all
local and national building codes, and
must not be blocked or obstructed. For
External Flue Termination Locations,
see diagram on page 8.
4) If installing the ue termination to a wall with
vinyl siding, the Vinyl Siding Stando󰀨 must
be used. Attach the Vinyl Siding Stando󰀨 to
the Horizontal Flue Termination, but rst run
a bead of non-hardening mastic around its
outside edges, so as to make a seal between
ue cap and the stando󰀨. Install the Vinyl
Siding Stando󰀨 (Part # 950) between the
ue cap and the exterior wall and attach
with the four wood screws provided. Seal
around the Vinyl Siding Stando󰀨 on all four
sides. Diagram 5. The arrow on the ue
cap should be pointing up. Insure that the
1-1/4" (32mm) clearances to combustible
materials are maintained. See diagram 5.
be terminated. If the wall being penetrated
is constructed of non-combustible material,
i.e. masonry block or concrete, a 7" (178mm)
diameter hole is acceptable.
Note:
a) The horizontal run of ue should have
a 1/4 inch (6mm) rise for every 1 foot
(.3m) of run towards the termination.
Never allow the ue to run downward.
This could cause high temperatures and
may present the possibility of a re.
INSTALLATION
DURA-FLUE
HORIZONTAL
INSTALLATIONS
1) Set the unit in its desired location. Check to
determine if wall studs or roof rafters are in
the way when the uing system is attached.
If this is the case, you may want to adjust
the location of the unit.
2) Room Sealed pipe and ttings are designed
with special twist-lock connections to con-
nect the uing system to the appliance ue
outlet. A twist-lock appliance adaptor is
installed on the unit at the factory. Assemble
the desired combination of
pipe and elbows to the ap-
pliance adaptor with
pipe seams oriented
towards the wall or
ceiling, as much out of
view as possible. The
nal positioning of the
pipe and 90oelbow as-
sembly is determined
by the mounting
orientation of the
adaptor on the
stove and twist-
locked for a solid
connection.
Note:
a) Twist-lock procedure: Four indentations,
located on the female ends of pipes and
ttings, are designed to slide straight
onto the male ends of adjacent pipes
and ttings, by orienting the four pipe
indentations so they match and slide in
to the four entry slots on the male ends
Diagram 1
990G 90O Elbow-Swivel Galv.
945BG 45O Elbow-Swivel-Black
990 90O Elbow Galv.
990B 90O Elbow-Black
990G 90O Elbow-Swivel Galv.
990BG 90O Elbow-Swivel-Black
991 High Wind Term. Cap (Vertical)
980 Vertical Term. Cap
982 Snorkel-14" Rise Term.Cap
981 Snorkel-36" Rise Term.Cap
940 Wall Thimble-Support/Box
941 Cathedral/Ceiling-Support/Box
3951 Brass Trim-Wall Thimble/
Ceiling Support
963 Firestop Spacer
943 Flashing 0/12-6/12
943S Flashing 7/12-12/12
953 Storm Collar
950 Vinyl Siding Stando󰀨
988 Wall Strap
942 Wall Thimble
Parts not supplied by Dura-Flue
946-506/P Flue Guard (Optional)
948-128 Vinyl Siding Shield
Astro Cap (Australian)
(diagram 1). Push the pipe sections
completely together, then twist-lock
one section clockwise approximately
one-quarter turn, until the two sections
are fully locked. The female locking lugs
will not be visible from the outside on
the Black Pipe or ttings. They may be
located by examining the inside of the
female ends. Apply sealant "Mill-Pac" to
inner pipe and high temp silicone sealant
to outer pipe on every twist-lock joint.
Hint: Apply silicone to female end.
b) Horizontal runs of ue must be supported
every three feet. Wall straps are available
for this purpose.
3) With the pipe attached to the stove, slide the
stove into its correct location, and mark the
wall for a 10" x 10" / 254mm x 254mm (inside
dimensions) square hole. The center of the
square hole should line up with the centerline
of the horizontal pipe, as shown in diagram 2.
Cut and frame the 10 inch (254mm) square
hole in the exterior wall where the ue will

Regency FG39-1 FireGenie Freestanding Gas Stove 15
Diagram 11: The upper half of the ashing is
installed under the roong material and not
nailed down until the chimney is installed. This
allows for small adjustments.
4) Assemble the desired lengths of black pipe
and elbows necessary to reach from the
appliance adaptor up though the Round
Support Box. Insure that all pipes and elbow
connections are in the fully twist-locked
position and sealed.
5) Cut a hole in the roof centred on the small
drilled hole placed in the roof in Step 2. The
hole should be of su󰀩cient size to meet
the minimum requirements for clearance
to combustibles of 1-1/4" (32mm) . Slip the
ashing under the shingles (shingles should
overlap half the ashing) as per diagram
11.
Diagram 12
7) Ensure ue is vertical and secure the base
of the ashing to the roof with roong rails,
slide storm collar over the pipe section and
seal with a mastic.
8) Install the vertical termination cap by twist
locking it.
6) Continue to assemble pipe lengths.
Note: If an o󰀨set is necessary in the attic to
avoid obstructions, it is important to
support the ue pipe every 3 feet, to
avoid excessive stress on the elbows,
and possible separation. Wall straps
are available for this purpose. See
diagram 7.
Galvanized pipe and elbows may be utilized
in the attic as well as above the rooine.
The galvanized nish is desirable above the
rooine due to its higher corrosion resist-
ance.
Continue to add pipe sections through the
ashing until the height of the ue cap meets
the minimum height requirements specied
in diagram 12 or local codes. Note that for
steep roof pitches, the vertical height must
be increased. A poor draft, or down drafting
can result from high wind conditions near
big trees or adjoining roof lines, in these
cases, increasing the ue height may solve
the problem.
Roof Pitch Minimum Flue Height
Feet Meters
at to 7/12 2 0.61
over 7/12 to 8/12 2 0.61
over 8/12 to 9/12 2 0.61
over 9/12 to 10/12 2.5 0.76
over 10/12 to 11/12 3.25 0.99
over 11/12 to 12/12 4 1.22
over 12/12 to 14/12 5 1.52
over 14/12 to 16/12 6 1.83
over 16/12 to 18/12 7 2.13
over 18/12 to 20/12 7.5 2.29
over 20/12 to 21/12 8 2.44
Diagram 10
Diagram 9
Diagram 8
Diagram 7
Diagram 6
DURA-FLUE VERTICAL
TERMINATION
1) Maintain the 1-1/4" (32mm)
clearances (air spaces) to
combustibles when passing
through ceilings, walls, roofs,
enclosures, attic rafter, or other
nearby combustible surfaces.
Do not pack air spaces with
insulation. Check page 9
for the maximum vertical
rise of the uing system and
the maximum horizontal o󰀨set
limitations.
3) To install the Round Support Box/Wall Thim-
ble in a at ceiling, cut a 254mm square hole
in the ceiling centred on the hole drilled in
Step 2. Frame the hole as shown in diagram
10.
INSTALLATION
7) Install the Wall Thimble in the center of
the 254mm square and attach with wood
screws.
8) Slide the decorative wall thimble up to the
wall surface being careful not to scratch
the paint and attach with screws provided.
Apply decorative brass or chrome trim if
desired. See diagram 7.
2) Set the gas appliance in
its desired location. Drop a
plumb bob down from the
ceiling to the position of
the appliance ue exit, and
mark the location where
the ue will penetrate the
ceiling. Drill a small hole
at his point. Next, drop a
plumb bob from the roof
to the hole previously drilled
in the ceiling, and mark the spot where the
ue will penetrate the roof. Determine if
ceiling joists, roof rafters or other framing
will obstruct the uing system. You may
wish to relocate the appliance or to o󰀨set,
as shown in diagram 9 to avoid cutting load
bearing members.

16 Regency FG39-1 FireGenie Freestanding Gas Stove
INSTALLATION
O󰀨set Chart
Diagram 13
Notes:
a) For multistorey vertical installations, a
Ceiling Fire stop (Part # 963) is required
at the second oor, and any subsequent
oor. Diagram 13. The opening should
be framed to 10 " x 10" (254mm x
254mm) inside dimensions, in the same
manner as shown in diagram 10.
b) Any occupied areas above the rst oor,
including closets and storage spaces,
through which the vertical ue passes, must
be enclosed.
CATHEDRAL CEILINGS
Round Support (RDS) &
Square Support (SQS)
If your home has a cathedral ceiling (no attic
space between the ceiling and the roof), install
the chimney and support as follows.
1) Situate the chimney in a convenient loca-
tion as near as possible to the appliance
outlet. Cut and frame a hole in the roof for
the support. The sides of this hole must be
vertical with 1 1/4" (32mm) clearance.
2) Place the support in the opening. Lower it
to the correct height as determined by the
table and diagram below.
Using a level, make sure the support is verti-
cal. If the support extends above the roof,
cut it ush with the top of the roof. Nail the
support to the frame opening using (8) 3"
(76mm) spiral nails or #8 x 1-1/2" (38mm)
screws.
Note: If you are using a 152mm square
support you may nd it di󰀩cult to
screw it in place because it is fairly
small inside.
Simpson Dura-Flue has provided angle
brackets with this support which can be
screwed to the outside of the support
box and nailed to surrounding framing as
required. Use a minimum of four #8 x 1/2"
(13mm) screws per bracket. In some cases
these brackets may need to be trimmed
(e.g.: to t under a ashing). Place the Fin-
ish Collar around the support and fasten it
to the ceiling using the screws provided.
3) Use appropriate roof ashing. Place the
ashing under the upper shingles and on top
of the lower shingles approximately half of
the ashing should be under the shingles.
4) Assemble the desired lengths of Black Pipe
and Elbows necessary to reach from the
appliance adaptor up through the support
box and ashing to proper height as per Dia.
12, local codes or page 9. Ensure that all
pipe and elbow connections are in their fully
twist lock position.
5) Ensure ue is vertical and secure ashing to
the roof with roong nails. Slide the storm
collar over the pipe section and seal with a
mastic.
6) Twist lock the ue cap on to the last sec-
tion.
Support Extensions - Round
(RDSE) or Square (SQSE)
Steep pitched cathedral ceilings may require
the use of a support extension. This piece ts
down inside the support and can be adjusted
to increase the support's length by up to 22"
(559mm). The extension is attached to the
support using the eight metal screws provided.
Be sure there is at least a 2 inch overlap where
the extension joins the support.
Slope "X"
0/12 - 2/12 4" (102mm)
2/12 - 7/12 5-1/2" (140mm)
7/12 - 12/12 6-3/4" (172mm)
12/12 - 24/12 7-1/2" (191mm)
24/12+ 12-1/2" (378mm)
1-1/4" (32mm) Min.
1-1/4" (32mm) Min.
1-1/4"
(32mm)
Min. 1-1/4" (32mm)
Min.
nails
Ceiling Firestop

Regency FG39-1 FireGenie Freestanding Gas Stove 17
INSTALLATION
GAS CONNECTION
The gas line should be rigid pipe. Copper may
also be used if approved by AS5601-2004.
The gas connection at the valve is 1/2 male.
For minimum and maximum supply pressure
see the System Data Table.
GAS PIPE PRESSURE
TESTING
The appliance must be isolated from the gas
supply piping system by closing its individual
manual shut-o󰀨 valve during any pressure
testing of the gas supply piping system at test
pressures equal to or less than 1/2 psig. (3.45
kPa). Disconnect piping from valve at pressures
over 3.45 kPa (14" w.c.).
The manifold pressure is controlled by a regulator
built into the gas control, and should be checked
at the pressure test point.
Note: To properly check gas pressure,
both inlet and manifold pressures
should be checked using the valve
pressure ports on the valve.
1) Make sure the valve is in the "OFF" posi-
tion.
2) Loosen the "IN" (# 3) and/or "OUT" (# 4)
pressure tap(s), turning counterclockwise
with a 1/8" (3mm) wide at screwdriver.
3) Attach manometer to "IN" and/or "OUT"
pressure tap(s) using a 5/16" (8mm) ID
hose.
4) Seal and or check the pilot outlet (# 8)
5) The pressure check should be carried out
with the unit burning and the setting should
be within the limits specied on the safety
label.
6) When nished reading manometer, turn
o󰀨 the gas valve, disconnect the hose and
tighten the screw (clockwise) with a 1/8"
(3mm) at screwdriver. Screw should be
snug, but do not over tighten.
AERATION
ADJUSTMENT
The burner aeration is factory set but may need
adjusting due to either the local gas supply or
altitude.
FG39 with 40 mj.
FG39-NG1 Fully Open
FG39-LPG1 Fully Open
Caution: Carbon will be produced if the air
shutter is closed too much.
Note: Any damage due to carboning result-
ing from improperly setting the aera-
tion controls is NOT covered under
warranty.
Burner Inlet Orice Sizes:
NG LPG
Burner #32 #50
2.95mm 1.78mm
Max. Input NG 40 Mj/h
LPG 38 Mj/h
Min. Input NG 20 Mj/h
LPG 19 Mj/h
Supply Pressure
NG min. 1.13 kPa
LPG min. 2.75 kPa
Manifold Pressure
NG .94 kPa
LPG 2.55kPa
Electrical: 240 V. 1.13A 60Hz.
Circulation: 2 speed fan, 125/75 CFM.
Log Set: Ceramic ber, 7 per set.
System Data
FG39 with 40mj.
EV1
EV2
R.Q.
ADJ.
P.OUT
MD
4321
Pin
11
8
9
10
1
2
3
4
6
7
5
SIT 845 VALVE DESCRIPTION
1) On-O󰀨 Solenoid Valve EV1
2) On-O󰀨 Solenoid Valve EV2
3) Inlet Pressure Test Point
4) Outlet Pressure Test Point
5) Connection for Pressure Regulator /
Combustion Chamber Compensation
6) Pressure Regulator for Minimum and
Maximum Outlet Pressure
7) Gas Outlet Pressure Electric Modulator
8) Pilot Outlet
9) Main Gas Outlet
10) Side Outlet
11) Main Gas Inlet

18 Regency FG39-1 FireGenie Freestanding Gas Stove
INSTALLATION
Conversion Kit for NG to LPG Model #360-968
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION!
918-578 12/20/06
3
PG121-1 / PG131-1 / FG39-1
Conversion Kit contains:
Qty. Part # Description
1 904-529 5/32" Allen Key
1 904-641 Burner Orifice #50
1 918-590 "Converted to LPG" label
1 908-528 Red "LPG" label
1 910-037 #30 ULPG Pilot Orifice
1 918-578 Instruction Sheet
1) Shut off the gas supply and unplug the
power cord.
2) Open the front door and carefully remove
the logs and lava rock.
3) Remove burner.
4) Remove burner orifice with a 1/2" wrench
and discard. Use a wrench to hold on to
the elbow behind the orifice.
5) Reinstall new burner orifice LPG stamped
#50 and tighten.
Burner Orifice
6) Pull out the pilot hood by hand.
Pilot
Hood
Pilot
Hood
removed
7) Remove the pilot orifice with the allen key.
Pilot
Orifice
8) Put in the new LPG orifice with the allen
key. Then put back the pilot hood.
9) Place the pilot hood back on.
10) Adjust the burner areation setting to fully
open and install the burner.
11)Remove the pedestal back cover by remov-
ing the 4 Phillips screws.
THIS CONVERSION MUST BE DONE BY A QUALIFIED GAS FITTER IF IN DOUBT DO NOT DO THIS CONVERSION !!
FG39-1 Conversion Kit #360-968 from NG to LPG
(refer to page 1 for PG121-1 / PG131-1)

Regency FG39-1 FireGenie Freestanding Gas Stove 19
INSTALLATION
918-578 12/20/06
4
PG121-1 / PG131-1 / FG39-1
12) Stick the conversion label "This unit has
been converted to LPG" over top of the
serial number decal.
13) Replace the yellow "NG" label with the red
"LPG" label.
14) Carefully pull out the control box.
Note: The control box is held in place by
velcro.
15) Remove the control box cover by undoing
the 3 screws. Maneuver through antenna.
Control Box
Cover
Antenna
17) Stick the conversion label "This unit has
been converted to LPG" on the control box
cover.
18) Reverse steps 15, 14 & 11.
19) Open the bottom door and remove the front
panel by undoing the 6 screws.
16) Remove the jumper using a plier.
After carrying out all adjustments, block
the setting screws with paint, taking care
not to obstruct the breather orifi ce of the
pressure.
Put back the modulator plastic cap.
WARNING: To ensure the correct opera-
tion of the modulator it is necessary that
the plastic cap (A) is returned to its original
location.
Cable
Electric
Modulator
21) Adjusting the Outlet Pressure
All the adjustments must be carried out in
the following order:
Remove the modulator plastic cap (A) using
needle nose pliers.
Maximum pressure: Turn the unit ON to
its highest input rating. Screw in the nut (B)
to increase the outlet pressure and screw
it out to decrease it. Use a 10 mm wrench.
NOTE: The outlet pressure must be set to
maximum 2.65 kPa.
20) Turn on the gas supply and plug in the power
cord.
Installer Notice:
These instructions must be left
with the appliance.
22) At the end of all setting and adjustment
operations, check electrical insulation and
gas leaks.
23) Reverse step 19.
24) Check operation of fan and flame control.
25) Check for proper flame appearance and
glow on logs.
C
B
A
Minimum pressure: Remove one of the
cables connected to the electric modulator.
Keeping the nut (B) blocked, screw in the
screw (C) to increase the pressure and screw
it out to decrease it. Use a screwdriver 6 x
1 blade.
NOTE: The outlet pressure must be set to
minimum 0.74 kPa.
Jumper
Jumper Location

20 Regency FG39-1 FireGenie Freestanding Gas Stove
LOG SET
INSTALLATION
Read the instructions below carefully and
refer to the diagrams. If logs are broken
do not use the unit until they are replaced.
Broken logs can interfere with the pilot
operation.
The gas log kit contains the following:
a) 02-65 Rear Log
b) 02-56 Middle Left Log
c) 02-44 Front Left Log
d) 02-46 Left Top Log
e) 02-45 Front Right Log
f) 02-47 Center Log
g) 02-48 Middle Right Log
h) Embers
i) Lava
Note: Install Optional Brick Panels prior to
installing logs.
Embers. Embers
The "02" refer numbers (i.e. 02-65) are
molded into the rear of each log.
1) Carefully remove the logs from the box and
unwrap them. The logs are fragile, handle
with care - do not force into position.
2) Sprinkle the embers on the left and right
sides of the rebox base.
INSTALLATION
C)02-44
Pins on Rear Log Support
A)02-65
B)02-56
3) Place Rear Log A)02-65 on the two pins on
the rear log support.
4) Place the Middle Left Log B)02-56 on the
two pins as shown.
5) Sprinkle some lava rock just in front of B)
02-56 on the burner holes.
lava rock
B)02-56
6) Place Front Left Log C)02-44 onto the 2
front pins as shown.