Regulus CSE TV ZV G 1F User manual

www.regulus.eu
CSE TV ZV G 1F
CSE TV ZV G 1F
EN
Installation and Operation Manual
CSE TV ZV G 1F PUMP STATION

1. Introduction
This pump station is designed to ensure that hot water circulates in building pipelines or in DHW production
systems.
2. Description of the pump station
The pump station consists of a UPM3 DHW 15-70 pump including a power cable, insulation, a non-return
valve and a thermometer.
Main features
Application DHW circuits – recirculation or heating in a heat exchanger
Description it consists of a UPM3 DHW 15-70 pump, insulation, non-return
valve and thermometer
Working fluid water, drinking water
Installation in a pipe, min. distance of the pipe axis from a wall is 100 mm
Code 15 181
Technical data of CSE TV ZV G 1F pump station
Fluid working temperature 2 - 95 °C
Max. working pressure 10 bar
Max. ambient temperature 70 °C
Max. rel. humidity 95 % non condensing
Power supply 230 V, 50 Hz
Insulation material EPP RG 60 g/l
Overall dimensions 325 x 140 x 220 mm
Total weight 2.0 kg
Connections 2x G 1" F

3. Flow direction
SMĚR PROUDĚNÍ
4. UPM3 DHW 15-70 Pump, 130 mm
Design
Wet-running circulation pump with G 1“ M connection.
Electrical data
Power supply 230 V, 50 Hz
Power input (min./max.) 2/52 W
Current (min./max.) 0.04/0.52 A
IP rating IP44
Max. speed 5766 rpm
Weighted average power ≤ 23 W
Energy Efficiency Index ≤ 0,20 by EN 16 297/3
Motor protection not needed
Minimum pressure at the suction port
Min. pressure at the suction
port to avoid cavitation
0.05 bar at 75 °C
0.50 bar at 95 °C
FLOW DIRECTION

Pump control
The circulation pump can be controlled without a PWM signal by selecting a pump performance curve or by
an external PWM signal (prole for use in heating systems). The cable with terminal for pump control using
PWM is not included in supply. It can be purchased as an option (code 16792), the cable is 2m long.
A maximum curve of a pump working range can be dened.
- without PWM signal the pump runs at the max. speed according to the selected curve
- with PWM signal the pump speed changes with the signal value up to the maximum of the selected curve
Performance curves
Curve Max. H Max. P1
(upper
graph)
(lower
graph)
14 m 25 W
25 m 33 W
36 m 39 W
47 m 52 W
Operation data
Fluid working temp. 2 to 95 °C
Max. working pressure 10 bar
Max. ambient temperature 70 °C
Max. rel. humidity 95 % non-condensing
Materials
Pump housing polyphenylene sulde (PPS)

Performance display
DISPLAY STATE PERFORMANCE in % of P1max
1 flashing green LED STAND-BY MODE
(EXTERNAL CONTROL ONLY) 0
1 green + 1 yellow LEDs LOW PERFORMANCE 0-25
1 green + 2 yellow LEDs MEDIUM-LOW PERFORMANCE 25-50
1 green + 3 yellow LEDs MEDIUM-HIGH PERFORMANCE 50-75
1 green + 4 yellow LEDs HIGH PERFORMANCE 75-100
When switched on, the pump runs at factory settings or the last setting. The display shows the momentary
pump performance.
Settings display
WARNING: LEDs may be turned by 180°, depending on the specic pump type.
By pressing the button the display switches to “performance view” and the current settings will be shown by
LEDs for 2 seconds (see gures below).
4 m 5 m 6 m 7 m
Error display
seized pump
too low power supply voltage
electric fault
Setting selection for UPM3
1. Press the pushbutton until the LEDs start ashing, the pump will switch to adjustment selection
mode.
2. To select your desired setting, press the button repeatedly until you find the setting you need (see
the figures below). If you pass the desired setting, you have to go one more round until it appears
again – there is no way back in the loop.
4 m 5 m 6 m 7 m
3. Release the button for more than 10 s and the LEDs will return to„performance view“, while the last
setting is saved.

©2020 We reserve the right to errors, changes and improvements without prior notice.
REGULUS spol. s r.o.
E-mail: [e-mail]
Web: www.regulus.eu
v1.1-06/2020
Forbidden pump positions
Permissible pump (actuator) positions
Pump wiring
socket for power supply (A)
and signal transmission (B)
power supply (A) and signal (B)
terminals
N (blue)
L (brown)
PE (yellow-green)
PWM GDN (blue)
PWM out (black)
PWM in (brown)
The B terminal with a 2m cable is not
included in supply; it can be
purchased as an option, code 16792.