Reid Sphinx II User manual

Display Manual
Sphinx II
Ananda D16

5.1 Start/ stop
5.2 Real-time speed/ mileage data display
5.3 Automatic headlight on/ off mode
5.4 Assist walk in 6 km/h
5.5 Assist level adjustment
5.6 Battery level display
5.7 Error code display
5.8 USB charging function display
5.9 WiFi function display
6.1 Trip distance parameter reset
6.2 Setting of light sensing parameters
6.3 Setting of speed unit
6.4 Setting of power consumption unit
6.5 Language setting
6.6 Setting of factory reset
6.7 Setting of automatic shutdown time
6.8 Setting of function clipping
6.9 WiFi settings
6.10 Display of motor read-only information
6.11 Display of battery read-only information
6.12 Display of instrument read-only information
Table of Contents
Instructions for users
1 About Users Guide
2 Material and overall dimension
3 Function Overview
4 Normal display areas
5 Normal operation
6. Instrument parameter setting
7. Connection diagram of lead wire
8. About instrument print code
9. Q&A
10. Quality Commitment and Warranty
11. Version Decleration

4
Instructions for users
Pay attention to safety during use. DO NOT plug in or
out when the instrument is power on.
This instrument shall be protected against collision as
practical as possible. Send the faulty meter for repair as
soon as possible.
1. About Users Guide
For better use of your electric bicycles, please read the
instructions for this instrument before use carefully. We
will tell you
everything about your use of this instrument in the
most concise way,
form hardware installation & settings to normal use of
instrument;
and meanwhile, we will help you eliminate all possible
confusions
and troubles.
2. Material and overall dimension
2.1 Material:
This instrument is made of black PC + ABS plastic shell.
It is free of sharp edges. Its appearance is of black
leather texture. The shell materials allow normal use
within the temperature range of - 20℃ and 60℃, and
can assure the good mechanical performance.
The screen is 2.4’’ TFT color dot matrix LCD. The key
module is separated from the instrument display
module. Level of protection is IP66. Strength conforms
to the provision for thrust > 250 N. Vibration conforms
to corresponding IEC provisions. Materials of parts
meet the requirements for RoHS and REACH
certifications. Tightening torque of locking screw is
1N.m.

The instrument key module is connected to the bottom
of theinstrument display module via cable.
Introduction to various keys:
◆[start/stop]key: key, substituted by word “start/stop”;
◆[plus]key: + key,substitutedbyword“plus”;
◆[minus]key: - key, substituted by word “minus”;
◆[headlight]key: key, substituted by word “headlight”;
◆[walk]key: key, substituted by word “walk”.
3. Function Overview
The instrument displays the followings:
◆ Battery level display
◆ Real-time speed display
◆ Mileage data (total mileage, trip distance, trip time,
max speed, average speed, average power
consumption, instantaneous power consumption,
motor power, cycling power and remaining mileage)
◆ Assist level display
◆ Headlight on and off
◆ 6 km/h assist walk function
2.2 Overall dimension (in mm)

◆ USB available for charging, output voltage/ max
output
current: 5V/1A
◆ WiFi function
◆ Error code display
◆ Instrument is available for one-key battery wakeup.
◆ Setting function display: clearing, light sensing, speed
unit, power consumption unit, language selection,
factory reset, WiFi status and name, automatic
shutdown time, and customized clipping
function.
◆ Read-only information display:
Firmware & hardware version numbers and serial
number of motor, total mileage;
Firmware & hardware version numbers, serial number,
voltage, cycle count and SOH of battery;
Firmware & hardware version numbers, and serial
number of the instrument
◆ Automatic control of backlight brightness (according
to intensity of external ambient light)
◆ Automatic control of headlight on and off (according
to intensity of external ambient light)
◆ Instrument conforms to EN 15194: 2017.
◆ WiFi meets RED certification requirements.
◆ Conform to CE certification requirements.
◆ Instrument supports ADST function (refer to the
Instructions
for Use of Full Functions of ADST Programmer Box).
◆ Communication protocol: Ananda New European
Standard Instrument Controller V11.0 Protocol_1.3.4 and
version above (the latest version shall prevail,
compatible with the previous versions)
◆ It may match with wide-voltage battery 24V/ 36V/48V
◆ Max working current is 50 mA.

Area ① indicates the current remaining battery level.
It is the
mode of battery display grid in the figure.
Area ② indicates USB charging.
Area ③ indicates the fault reminds.
Area ④ indicates WiFi.
Area ⑤ shows the headlight status indication,
including automatic mode and manual mode .
Area ⑥ indicates the speed unit.
Area ⑦ indicates the real time speed value.
Area ⑧ indicates the content of ODO mileage data.
Area ⑨ indicates the mode of ODO mileage.
Area ⑩ indicates the status of assist walk.
Area ⑪ indicates the current gear level.
5. Normal operation
5.1 Start/ stop
◆ The instrument has been turned on when the
battery has output. The battery will be closed by
keeping the battery button pressed and meanwhile,
the instrument will be shut off automatically and the
system will be turned off.
4. Normal display areas

◆ The instrument has been turned on when the battery
has output. The battery will be closed and the system
will be turned off if the instrument is shut off before the
battery.
◆ If the instrument has been turned on when the
battery has output, the instrument will be shut off by
keeping the instrument on-off key pressed for 2
seconds. If the instrument is not opened, the
instrument will be opened by keeping the instrument
on-off key pressed for 1 second.
◆ This instrument is such set that it will enter auto-sleep
mode if the system has been idle for 5 consecutive
minutes (specific time can be set via instrument
parameter/ automatic shutdown time) and the
instrument current is lower than 6 mA in the sleep
mode, as factory default.
◆ The battery will be closed and the system will be
turned off automatically if the system has been idle for
30 consecutive minutes.
◆ After startup, the instrument will firstly show the
interface “ANANDA” and then enter into the main
interface.
Startup interface Main interface

5.2 Real-time speed/ mileage data display
In the main interface, current speed will be refreshed in
a real time manner and meanwhile, mileage related
data can be checked. It may switch the display of ODO
mileage data by pressing the key “start/ stop”, in the
following sequence: Total mileage -> trip distance ->
trip time -> average speed for single trip -> max speed
for single trip -> motor power -> average power
consumption of single trip -> instantaneous power
consumption -> remaining mileage.
Total mileage
display
Trip distance
display
Trip
time
Average
speed
Max
speed
Motor
power
Average power
consumption
Instantaneous
power
consumption
Remaining
mileage

5.3 Automatic headlight on/ off mode
In the main interface, operations to realize the
headlight function
can be done. When the headlight is off, it can be
turned on by keeping the key “headlight” pressed
manually; if the headlight is on, it can be turned off by
keeping the key “headlight” pressed manually.
5.4 Assist walk in 6 km/h
In the main interface, the operation to realize 6 km/h
assist walk function can be done. By keeping the key
“walk” pressed, it will light the assist walk sign and enter
the interface of assist walk, which means that the assist
walk mode is activated. Then, it can execute the
function of assist walk in 6 km/h by pressing the key
“walk” again and keeping the key “walk” pressed; this
function will fail and it will exit the assist walk mode if
the key “walk” is released.
Status of
automatic
headlight
turned on
Walk mode

5.5 Assist level adjustment
In the main interface, gear position operation can be
realized. It may add the gear level by pressing the key
“plus” and reduce the gear level by pressing the key
“minus”. Output power of motor can be changed by
adding and reducing the assist level. Assist level of this
instrument is 0~4, among which level 0 means that
motor has no output power while level 4 means that
motor has the max output power. When the
instrument is started, it will enter gear level 1 by default.
When gear levels 0~4 are chosen, it will display “OFF”,
“ECO”, “SPORT”, “SHIFT” and “BOOST” respectively. It
will display “WALK” in the state of assist walk.
Level
OFF
Level
ECO
Level
SPORT
Level
SHIFT
Level
BOOST