REIST INDUSTRIES Roto-Rake RR96 Product manual

INNOVATION WORKING FOR YOU
RR96
Roto-Rake
Operator and Parts Manual
Effective Serial Number Y4401
REIST Industries Inc.
100 Union Street
Elmira, Ontario, Canada
N3B 3L7
Phone: [phone]
Toll Free: 1-877-467-3478
www.reistindustries.com

Contents
INTRODUCTION......................................................................................................................... 2
PRODUCT CONFIGURATION ................................................................................................... 3
GENERAL SAFETY PRECAUTIONS ......................................................................................... 4
GENERAL SAFETY PRECAUTIONS ......................................................................................... 5
OPERATION AND TRANSPORTATION ON PUBLIC ROADS AND AREAS............................. 6
SAFETY DECALS....................................................................................................................... 7
SAFETY DECALS . . . cont’d ...................................................................................................... 8
MAINTENANCE.......................................................................................................................... 8
STANDARD SETUP INSTRUCTIONS........................................................................................ 9
SKID-STEER HOOKUP INSTRUCTIONS .................................................................................. 9
OPERATION OF ROTO-RAKE................................................................................................... 9
FLOAT SETUP INSTRUCTIONS.............................................................................................. 10
FLOAT SETUP OF ROTO-RAKE.............................................................................................. 10
STANDARD FEATURES ASSEMBLY...................................................................................... 11
RR96 ROTO RAKE - ASSEMBLY............................................................................................. 12
RR96 WHEEL ASSEMBLY....................................................................................................... 13
STANDARD 15 DEGREE SWIVEL FRAME ASSEMBLY......................................................... 14
BASE UNIT & HITCH ASSEMBLY............................................................................................ 15
OPTIONAL ON THE FLY HYDRAULIC VALVE BLOCK........................................................... 16
OPTIONAL HYDRAULIC VALVE BLOCK DETAILS................................................................. 17
OPTIONAL HYDRAULIC VALVE BLOCK DETAILS................................................................. 18
OPTIONAL VALVE BLOCK WIRING HARNESSES................................................................. 19
OPTIONAL DIVERTOR VALVE................................................................................................ 20
OPTIONAL DIVERTOR VALVE ASSEMBLY DETAILS............................................................ 21
OPTIONAL DIVERTOR VALVE DETAILS & SCHEMATIC....................................................... 22
WIRING HARNESSES.............................................................................................................. 23
OPTIONAL SIDE CUTTERS - RRSCK..................................................................................... 24
OPTIONAL PLOW ATTACHMENT ASSEMBLY....................................................................... 25
WARRANTY INFORMATION.................................................................................................... 26
Record your product information for future reference:
Model Number: ______________
Serial Number: ______________
In Service Date: _____________
Sold By: ___________________

REIST Industries Inc. © (revised April 2022)
Page 2
INTRODUCTION
Thank you for choosing the REIST RR96 ROTO-RAKE.
We feel confident that this equipment will meet your expectations in workmanship, reliability and
performance when used as designed. This manual is to assist you with the safe operation of
your REIST ROTO-RAKE. It also has a parts list to help you when replacement parts are
required. Any person who will be assembling, attaching, maintaining, or operating this product
and the prime mover to which it is attached, are required to read and completely understand the
information and instructions contained in this manual and that of the prime mover. Always
obtain further assistance by contacting the dealer from which this product was purchased or by
contacting REIST Industries at the telephone number or address below. Keep this manual
available for reference whenever this product is being handled or used and we recommend that
it is reviewed periodically and before seasonal use. Provide this manual to any new owners
and/or operators and ensure they fully understand the safe operation of this equipment before it
is placed in service.
Replacement copies of this manual are available for downloading at:
www.reistindustries.com
Innovation Working for You
REIST Industries Inc.
100 Union Street
Elmira, Ontario, Canada
N3B 3L7
Phone: [phone]
Toll Free: 1-877-467-3478
The illustrations and information contained within this manual were current at the
time of publication. Under our policy of continuous improvement, we reserve the
right to change specifications and designs without prior notice. The illustrations do
not necessarily show the standard version of product offered by REIST Industries.

REIST Industries Inc. © (revised April 2022)
Page 3
PRODUCT CONFIGURATION
To ensure that the ROTO-RAKE is matched to the right prime mover, REIST ROTO-
RAKE models are as follows:
ROTO-RAKE
Model
Working
Width
GPM
Max
PSI
Mount
Pounds
Kilograms
RR96
96”
18 to 35
3000
Skid Steer
1350
615
With optional Valve Manifold add 120 lbs (55 kg)
The following references are used throughout this Operator’s and Parts Manual:
Attachment,
Implement
Refers to the ROTO-RAKE whether attached or separate from the prime
mover
Prime Mover
The engine-driven machine to which this product is attached
Equipment
Refers to the Implement and or prime mover whether separate or
connected
WARNING,
DANGER,
IMPORTANT
A notice that relates to the safe and efficient operation of the ROTO-
RAKE or prime mover. Read and understand the reference before
attaching or operating the ROTO-RAKE or the prime mover.
Exceeding the recommended specifications can result in damage to the equipment
and will void all REIST Industries warranties.

REIST Industries Inc. © (revised April 2022)
Page 4
GENERAL SAFETY PRECAUTIONS
Careful operation is the best assurance against accidents. It is the owner’s responsibility to
make sure that all operators read and understand this manual and follow the recommendations,
cautions and warnings before connecting to a prime mover and operating the equipment. The
REIST ROTO-RAKE was designed for use to grade and level all types of soil including stone
dust, gravel or similar products.
Familiarize yourself with all controls and know how to quickly stop the equipment and all
rotating parts in the case of an emergency.
Never let an untrained person or a child operate equipment.
MAINTAIN AND REPAIR EQUIPMENT SAFELY
•Do not wear loose clothing, or any accessories that can catch in moving parts
•If you have long hair, cover or secure it so that it does not become entangled
in the equipment
•Work on a level surface in a well-lit area.
•Always lower raised equipment to the ground or securely support it to prevent
unintentional movement
•Remove and retain the prime mover’s ignition key
•Use the correct tool for the job at hand. Make sure they are in good condition
for the task required
•Wear the protective equipment specified by the tool manufacturer
•Use care when working on hydraulic systems and understand how to check
for and release trapped hydraulic pressure
DO NOT MODIFY THE ROTO-RAKE OR PRIME MOVER
Modifications may weaken the integrity of the ROTO-RAKE and may impair the
operation, safety, and performance of the product. When making repairs, only
qualified technicians using the manufacturer’s genuine parts, following authorized
instructions, shall attempt the repair. Never modify any ROPS (Roll Over Protection
Structure) or FOPS (Falling Object Protective Structure) equipment or other safety
device or remove guarding. Any modifications must be sanctioned in writing by an
authorized representative of the manufacturer.

REIST Industries Inc. © (revised April 2022)
Page 5
GENERAL SAFETY PRECAUTIONS
Never use your hands to clear if clogged. Never allow anyone to reach into the rotor housing.
The rotor can crush and/or dismember. Keep everyone clear of the rotor until the prime mover
engine is off and the hydraulic pressure has been relieved.
•Do not operate an engine in confined or non-ventilated area
•Do not perform adjustments or repairs with the engine running
•Always lower raised equipment to the ground or securely support it to prevent
unintentional movement
•Do not operate on excessive inclines or side slopes –know the limitations of the prime
mover –be careful when turning on slopes as a rollover condition may exist
•Never carry passengers
•Keep bystanders away from the machine when in operation
•Be aware of pedestrians
•Know how to quickly stop the equipment and all rotating parts in the case of an
emergency
•Stop the prime mover, lower implements and turn off the engine before dismounting
•Refer to the prime mover’s Operator’s Manual for additional information
READ OPERATOR’S MANUAL BEFORE OPERATING
Do not operate equipment until you are completely trained by a qualified operator in
how to use the controls, understand the machine’s capabilities, dimensions, and all
safety requirements. Refer to your operator’s manual for these instructions.
STAY CLEAR OF ROTATING OBJECTS
Keep hands, feet and clothing away from power driven rotating parts.

REIST Industries Inc. © (revised April 2022)
Page 6
OPERATION AND TRANSPORTATION ON PUBLIC ROADS AND
AREAS
Always adhere to the local laws and regulations concerning traveling or operating on public
roadways and areas. Clean all lights, reflectors and mirrors ensuring that all lighting is in
working order before moving. Know the area! i.e. Elevations, steep side drop offs. Watch out for
pedestrians and use caution when approaching pedestrians, hazardous objects (stones, etc.)
may inadvertently be discharged. Always be alert while transporting or operating the equipment.
Select a safe ground speed when transporting from one area to another. When operating, or
driving on roadways, travel in such a way that faster moving vehicles may pass you safely.

REIST Industries Inc. © (revised April 2022)
Page 7
SAFETY DECALS
Contact REIST Industries if replacement safety signs are required.
DECAL PART NUMBERS
Item Part Number Description
RD106 REIST Decal
RD115 Made in Canada Decal
RD132 Roto Rake Decal
RD155 RR96 Decal
Serial Serial Number Decal
WD111 WARNING Rotating Knives & Spikes
WD112 WARNING Read Manual Decal
7

REIST Industries Inc. © (revised April 2022)
Page 8
SAFETY DECALS . . . cont’d
Contact REIST Industries if replacement safety signs are required.
DECAL PART NUMBERS
Item Part Number Description
WD115 WARNING Pinch Point Decal
WD116 WARNING Flying Objects Decal
MAINTENANCE
Refer to the General Safety Precautions, page 5 of this manual before performing any
maintenance.
1. Always ensure the ROTO-RAKE is properly installed, the prime mover is positioned
on a level surface with the park brake set and the ROTO-RAKE positioned on the
ground
2. Shut-off the engine and remove and retain the ignition key
3. Chock the wheels to prevent movement and release residual hydraulic pressure
4. Grease hinge points every 50 hrs.
5. At the beginning of each season, ensure that all fasteners are properly torqued, all
safety guards are in place and that operator’s manual is reviewed and understood
6. At the end of season, perform all maintenance activities and protect exposed hose
ends. Always check for missing or damaged parts and repair as required.

REIST Industries Inc. © (revised April 2022)
Page 9
STANDARD SETUP INSTRUCTIONS
Improper installation, operation, or maintenance of this equipment could result in serious injury
or death. FOLLOW ALL SAFETY INSTRUCTIONS IN THIS MANUAL AND THE PRIME
MOVER'S MANUAL(S).
Refer to the operator’s manual(s) for your prime mover and follow the mounting instructions
contained therein.
SKID-STEER HOOKUP INSTRUCTIONS
The standard ROTO-Rake has a universal Skid Steer mount. Attach Skid steer to Roto-Rake
and attach the two Hydraulic hoses. Different makes of skid steers have different wiring
configurations. You need the correct wiring harness.
OPERATION OF ROTO-RAKE
•Be sure the area is clear of all bystanders
•Refer to the prime mover starting instructions
•Lower ROTO-RAKE to ground, putting skid steer arms in float position.
•For leveling control, you want the weight on the wheels of the Roto-Rake
•Tip the bucket cylinders of the skid steer until tips of rotor are at desired depth.
STAY CLEAR OF ROTATING OBJECTS
Keep hands, feet and clothing away from power driven rotating parts.

REIST Industries Inc. © (revised April 2022)
Page 10
FLOAT SETUP INSTRUCTIONS
The ROTO-RAKE can be used in a float condition that will allow it to follow minor ground
contours instead of gouging the terrain with a rigid connection. With the ratchet set so that the
Roto Rake is horizontal on level ground, the operator can engage the Float feature.
FLOAT SETUP OF ROTO-RAKE
•Remove the locking hairpin from the pin holding the tilt adjuster end in the hole under the
slot and pull it out.
•Raise the tilt adjuster end until the clevis hole lines up with the slot and insert the pin.
•Secure the pin in the slot with the hairpin.
•The float position allows the Roto-Rake to tilt and follow minor variations in the contours
of the ground.
•The float position allows 7” of up and down movement as the Roto Rake travels across
uneven ground.
•The Wheel Attachment may be left either engaged or disengaged at the discretion of the
operator.
Rigid Position Float Position

REIST Industries Inc. © (revised April 2022)
Page 11
STANDARD FEATURES ASSEMBLY

REIST Industries Inc. © (revised April 2022)
Page 12
RR96 ROTO RAKE - ASSEMBLY

REIST Industries Inc. © (revised April 2022)
Page 13
RR96 WHEEL ASSEMBLY

REIST Industries Inc. © (revised April 2022)
Page 14
STANDARD 15 DEGREE SWIVEL FRAME ASSEMBLY

REIST Industries Inc. © (revised April 2022)
Page 15
BASE UNIT & HITCH ASSEMBLY

REIST Industries Inc. © (revised April 2022)
Page 16
OPTIONAL ON THE FLY HYDRAULIC VALVE BLOCK

REIST Industries Inc. © (revised April 2022)
Page 17
OPTIONAL HYDRAULIC VALVE BLOCK DETAILS

REIST Industries Inc. © (revised April 2022)
Page 18
OPTIONAL HYDRAULIC VALVE BLOCK DETAILS