Rejuvenation CANBY TRESTLE TABLE User manual

REJUVENATION
CANBYTRESTLETABLE– ASSEMBLYINSTRUCTIONS

Step1– PrepareParts&Tools
Beforegettingstarteditisagoodideatoread
throughtheseassemblyinstructionsentirelyandto
collectthetools&hardwareyouneed:
1. CanbyTrestletabletop(boxed)
2. CanbyTrestletablelegs(boxed)
3. Hardwarepackincluding:
•20ea.1”long,black,top‐mountingscrews
•2ea.¼”‐20x3/8”truss‐headallen screws
•1ea.5/32”allen wrench
4. Ascrewdriveror,betteryet,adrilldriver.

Canby’ssolidhardwoodtopsareheavy.We
recommendthatyouhavethehelpofa
friendwhenhandlingthem.
Step2– UnpackTop
Carefullyunpackyourtopandsetitfacedownona
cleancarpetedsurface.Soasnottoscratchor
dentthetopface–Pleaseensuretheareainwhich
you’reworkingisfreefromanydebris.

CarefullyunpackyourCanbyTrestletablelegs.So
asnottodingorscratchthempleaseusecarewhen
removingthemfromthebox.
IMPORTANT ‐Avoidusingaknifetoremovethe
bubblewrapandotherpackagingmaterialsas
there’sagreaterriskofscratchingtheparts.
Asshown,placethelegsateachendofthetable
top.Lineupthepilotholesinthetopwiththe
mountingholesinthelegs.Ifneedbe,thelegscan
beflexedopenofclosedabittogetthingstoline
up.
Insurethattheslotsonthebottomandatthe
centerofeachlegarefacingtheinsideofthetop.
Step3 – Unpack&PositionTableLegs
IMPORTANT
Slotsfacingto
insideoftabletop.

WiththeholeslinedupinStep3,startascrewineachofthe8holesatone
endofthetable.Donotfullytightenthemyet.
Step4–FastenLegtoTableTop

Withoneleglooselyattached,youcannowconnect
astretcher.
Insertthethreadedtabatoneendofthestretcher
intotheslotintheleg.Usingthesuppliedallen
wrenchthreadoneofthe3/8”longallen head
screwsthroughthebottomofthelegandintothe
tab.Thisscrewcanbetightened.
Lineuptheholesinthemountingbracketatthe
otherendofthestretcherwiththematchingpilot
holesinthetop.Installa1”top‐mountingscrewin
eachhole.Tightenthetop‐mountingscrews.
Step5– ConnecttheStretcher

Repeatsteps4and5attheotherendofthetable.Oncebothlegsandbothstretchersare
connected,goaroundandtightenall16ofthetop‐mountingscrews.
Step6– Connect2nd Leg&Stretcher

Fullyassembled,CanbyTrestletablesareheavy.Inordertoavoiddamagetothe
tableorinjurytoyourself,youmusthavetwopeopletoflipthetableover.
Withoneofyouateachend,startbytiltingthetableontooneofit’slongsides.
Graspingbothalegandtheedgeofthetabletop,carefullyliftthetablefullyoff
theground,flipitupright,andplaceitgentlyonthefloor…Enjoy!
Step7– FlippingtheTableUpright