Rejuvenation WARRENTON 61in Vanity User manual

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 1/12

WARRENTON 61in Vanity

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 2/12

BEFORE YOU BEGIN
 Marble top is both heavy, and until installed, fragile. Please have a helper and use caution when moving marble
top.
 Make sure to observe all local plumbing codes.
 Prior to installation, unpack and inspect both the console and marble top and porcelain lavatory for damage.
Locate the installation parts package and put in a safe place—you will need this for installation.
 Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
 Installation assumes that walls and floor are plumb and level. Please make appropriate adjustments for other
conditions.
 Remove any molding that may prevent the console from being set flush to the finished wall.
TOOLS AND MATERIALS
 Tape measure
 Pencil
 Level
 Drill with appropriate drill and driver bits
 Eye protection
 Clear 100% silicone adhesive caulk
 Wood screws (for securing console to wood framing)
CARE INSTRUCTIONS
 Dust often using a clean, soft, dry and lint-free cloth.
 Immediately blot up spills, then wipe with a clean, damp cloth.
 We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered finish.
 Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if
necessary.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 3/12

Install with hand screwdriver ONLY

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 4/12 

TEST FIT THE VANITY BASE
 Remove the drawers, mark their location to ensure they go back into their original positions.
 Set aside in a safe place and push the drawer slides back into the vanity.
 Position the vanity base in the desired location against the finished wall. Remove baseboard
as needed.
 Verify that the vanity base is level: front to back and side to side. Adjust the levelers at the
bottom of the legs as necessary. Once vanity base is level extend leveler on center foot

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 5/12

ATTACH THE VANITY BASE TO THE WALL
 Locate two wall studs to secure the vanity base. Mark these locations on the back rail
of the vanity base. Drill pilot holes through the back rail and into the studs. If necessary
provide shims between vanity and back rail so the vanity base is not distorted.
 Using wood screws (supplied by others), secure the vanity to the wall.
ATTACH THE UNDERMOUNT SINKS TO THE TOP
(Single sink shown. Double sink similar)

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 6/12

ATTACH THE UNDERMOUNT SINKS TO THE TOP (CONT’D)
(Single sink shown. Double sink similar)

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 7/12

ATTACH TOP TO VANITY BASE

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 8/12

INSTALL BACKSPLASH
 Apply a bead of caulk at the back of the top and BACK of the backsplash.
 Press against wall and align evenly side to side.
 Hold in place with blue painter’s tape until caulk cures.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 9/12

CONNECT FAUCETS AND PLUMBING
Keep these clearances in mind when routing plumbing so drawer movement will not be restricted

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 10/12 

REINSTALL DRAWERS
Note location to ensure drawers go back in their original location
ADJUST DRAWER FRONT ALIGNMENT IF NECESSARY

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 11/12


DIMENSIONS
BACK PLUMBING ACCESS CUTOUTS
Back is ¾” thick plywood

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-01-08 rev.1 www.rejuvenation.com 12/12

MARBLE TOP - SINK AND FAUCET CUTOUTS


