Rejuvenation GENEVA 36in Vanity User manual

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 1/15
GENEVA 36in Vanity

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 2/15
BEFORE YOU BEGIN
•Marble top is both heavy, and until installed, fragile. Please have a helper and use caution when moving
marble top.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 3/15
BEFORE YOU BEGIN (cont’d)
•Make sure to observe all local plumbing codes.
•Prior to installation, unpack and inspect both the console and marble top and porcelain lavatory for damage.
Locate the installation parts package and put in a safe place—you will need this for installation.
•Do not dispose of any packaging or contents of the shipping carton until assembly is completed to avoid
accidentally discarding small parts or hardware.
•Installation assumes that walls and floor are plumb and level. Please make appropriate adjustments for other
conditions.
•Remove any molding that may prevent the console from being set flush to the finished wall.
TOOLS AND MATERIALS
•Tape measure
•Pencil
•Level
•Drill with appropriate drill and driver bits
•Eye protection
•Clear 100% silicone adhesive caulk
•Screws for securing vanity to building framing DO NOT USE WALL ANCHORS
•Wood blocking - if building has steel wall studs or wall studs are not in appropriate locations
CARE INSTRUCTIONS
•Dust often using a clean, soft, dry and lint-free cloth.
•Immediately blot up spills, then wipe with a clean, damp cloth.
•We do not recommend the use of chemical cleansers, abrasives or furniture polish on our finishes.
•Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if
necessary.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 4/15

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 5/15
ATTACH THE VANITY BASE TO THE WALL
DO NOT INSTALL WITH SHEETROCK ANCHORS
1. Remove drawers and set aside in a safe place. No tools are needed. Make a note of their
original location.
2. Mark the desired height of the marble top. (34” and 36” are averages), draw a horizontal
reference line 1-3/16” below that mark to represent the top of the vanity base without the
marble top.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 6/15
ATTACH THE VANITY BASE TO THE WALL (CONT’D)
3. Use the drawing below to mark out the location of the vanity base and opening on your wall.
4. In each of the shaded areas, mark 2 fastener locations that align with studs and avoid
plumbing pipes. If you can’t locate studs at the fastener locations or you have steel studs,
remove drywall, add 2 x 6 blocking to create fastener locations and reinstall drywall.
5. Drill (4) appropriately sized pilot holes into the studs or blocking to avoid splitting. For the
fasteners supplied with the vanity, use a 1/4” diameter drill bit.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 7/15
ATTACH THE VANITY BASE TO THE WALL (CONT’D)
6. Transfer the pilot hole locations to the back of the vanity base and drill 3/8” diameter
fastener clearance holes.
7. With a helper, secure the vanity base to the studs or blocking using the fasteners
and washers supplied (see page 8 for cross-section view).
8. If necessary, place shims between the vanity and wall so the vanity base is not distorted
and stays level in all directions.
9. Push down on the vanity to check all 4 fasteners are holding properly.

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 8/15
ATTACH THE VANITY BASE TO THE WALL (CONT’D)

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 9/15
ATTACH THE UNDERMOUNT SINK TO THE TOP

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 10/15
ATTACH THE UNDERMOUNT SINK TO THE TOP (CONT’D)

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 11/15
ATTACH TOP TO VANITY BASE

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 12/15
INSTALL BACKSPLASH
•Apply a bead of caulk at the back edge of the top and the BACK of the backsplash.
•Press against wall and align evenly side to side.
•Hold in place with blue painter’s tape until caulk cures

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 13/15
CONNECT FAUCETS AND PLUMBING
Keep these clearances in mind when routing plumbing

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 14/15

Assembly instructions
Instructions d’assemblage
Instrucciones de Ensamblaje
2019-11-13 www.rejuvenation.com 15/15
REINSTALL DRAWERS