Remii CLASSIC SLIM-26 Owner's manual

INSTALLATION AND OPERATION INSTRUCTIONS FOR
INSTALLATION AND OPERATION INSTRUCTIONS FOR
X
X
X
CLASSIC SLIM - 26
CLASSIC SLIM - 30
CLASSIC SLIM - 33
INSTALLATION AND OPERATION INSTRUCTIONS FOR
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE
INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE
CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE

2
TABLE OF CONTENTS
Please read and carefully follow all of the instruction found in this manual. The instructions
included here will assure that you have many years of dependable and enjoyable service
from your Amantii Electric Fireplace.
IMPORTANT INSTRUCTIONS ......................................................................................................................................... 3
UNPACKING AND TESTING THE APPLIANCE .......................................................................................................... 6
GROUNDING THE APPLIANCE ...................................................................................................................................... 6
LOCATING THE FIREPLACE ........................................................................................................................................... 6
CLASSIC SLIM -26............
.. ................................................................................................................................................ ................................. 7
CLASSIC SLIM-30................................................................................................................................. .................................. 8
CLASSIC SLIM 33
........................................................................................................................................................... ........................ 9
BUILT IN INSTALLATION ............................................................................................................................................. 10
HARDWIRE INSTALLATION ........................................................................................................................................ 14
MEDIA OPTIONS .............................................................................................................................................................. 16
DECORATIVE MEDIA INSTALLATION ...................................................................................................................... 16
OPERATION ....................................................................................................................................................................... 17
MANUAL OPERATION ................................................................................................................................................... 17
REMOTE CONTROL OPERATION ................................................................................................................................ 18
WIFI OPERATION ............................................................................................................................................................. 21
INSTALLING WALL THERMOSTAT ........................................................................................................................... 24
REPLACEMENT PARTS .................................................................................................................................................. 2
EXPLODED VIEW ............................................................................................................................................................ 26
TROUBLE SHOOTING ..................................................................................................................................................... 27
SERVICE HISTORY .......................................................................................................................................................... 28
WARRANTY ...................................................................................................................................................................... 29

3
IMPORTANT INSTRUCTIONS
1. Read all instructions before installing or using this heater.
. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet from the front, sides and rear of the heater.
3. Always unplug heater when not in use.
4. Do not operate the fireplace if it has a damaged cord or plug, after it has
malfunctioned, or if the unit has been dropped or damaged in any way.
5. Do not use the heater outdoors.
6. Do not run the cord under carpeting. Do not cover the cord with throw rugs, runners
or anything else. Arrange the cord away from traffic areas where it could not be
tripped over.
7. To disconnect the heater, turn the controls to "OFF" before removing the plug from
the outlet.
8. Do not insert or allow foreign objects to enter any ventilation or exhaust opening, as
this may cause an electric shock, fire or damage to the heater.
9. To prevent the possibility of fire, do not block air intakes in any manner.
10. A heater has hot and arcing or sparking parts inside. Do not use it in areas where
gasoline, paint or flammable liquids are used or stored.
11. Use this heater only as described in this manual. Any other use is not recommended
by the manufacturer, as it may cause fire, electric shock or injury.
1 . Avoid the use of an extension cord, the extension cord will overheat and cause a fire.
13. Always use properly grounded fused and polarized outlets.
14. Always use ground fault protection where it is required by electrical codes.
15. Always disconnect the power before performing any cleaning, maintenance or
relocation of the heater.
16. To prevent a possible fire, do not burn wood or other materials in this heater.
17. To prevent electric shock or fire, always use a certified electrician, should new
circuits or outlets be required.
18. When transporting or storing the heater, keep it in a dry place, free from excessive
vibration.
19. This appliance should not be modified under any circumstances.
0. Packaging material should be kept away from children and be disposed of in a safe
manner. Plastic bags are not toys and should be kept away from children and
infants.

4
1. Do not use this heater in small rooms when they are occupied by persons not
capable of leaving the room on their own, unless constant supervision is provided.
. If the glass is damaged, do not use the heater to avoid a hazard.
3. Do not leave children unsupervised when the heater is turned on.

Cautions
Do’s
 Always install the heater in accordance with this guide. If in doubt obtain
expert advice.
 Always make sure the electrical socket is accessible and located adjacent
to, but not above the heater.
 Always disconnect the heater from the electrical supply before moving it, or
carrying out cleaning, maintenance.
 Always make sure the heater is firmly secured to prevent it from being
tipped over.
 Always use a fireguard when young children and infirm persons can come
into contact with the heater.
Don’ts
 Never leave children unsupervised in a room where the heater is ON and
unguarded.
 Never obstruct or cover the fan outlet or force items into heater openings.
 Never install or use the heater anywhere where water is in use, for
example: bathrooms, kitchens, or swimming pools.
 Never use aerosols or steam cleaners on or around the heater.
 Never route the mains supply cable under carpet etc.
 Never install the heater close to curtains or combustible materials.
 Never use the heater to dry clothes etc.
 Never sit or stand on the heater.

UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance, te
the power supply cord into a 1 0 Volt grounded outlet.
Test all aspects of its operation (manual switches, remote and heater) to make sure all
components are operating correctly.
As with most el
ectronic devices, your new electric fireplace has been designed to operate at
temperatures between 5 ℃ (41
℉
fireplace to reach room temperature before turning it on.
NOTE: Th r may b trac s
of odor during th first f w minut s of initial us . This is
harml ss and
normal and will n v r occur agai
GROUNDING APPLIANCE
This appliance is for use on 1 0 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three
receptacles. The green grounding lug extending from t
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
three-
slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider the following:
1.
Where the fireplace is located must allow for wall and ceil
.
Consider a location where the fireplace screen will not be exposed to direct sunlight from
windows or doors.
3.
A 15 ampere, 1 0 Volt, 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch cir
to trip or fuses to blow.
6
UNPACKING AND TESTING APPLIANCE
Carefully remove the appliance from the box.
Prior to installing the appliance, te
st to make sure the appliance operates properly by plugging
the power supply cord into a 1 0 Volt grounded outl
et.
Test all aspects of its operation (manual switches, remote and heater) to make sure all
components are operating correctly.
ectronic devices, your new electric fireplace has been designed to operate at
℉
) and 35 ℃ (95℉
). During the cold winter months, allow the
fireplace to reach room temperature before turning
it on.
of odor during th first f w minut s of initial us . This is
normal and will n v r occur agai
n.
This appliance is for use on 1 0 Volts. The cord has a plug as shown in (A). An adapter as
shown in (C) is available for connecting three
-
blade grounding type plugs to two
receptacles. The green grounding lug extending from
t
he adapter must be connected to a
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
slot grounded receptacle is available.
To disconnect appliance, turn controls to off, then remove plug from outlet.
LOCATING THE FIREPLACE
Plan where to locate and frame the fireplace. This will save time and money later when you
install the fireplace. Before installation consider
the following:
Where the fireplace is located must allow for wall
and ceil
ing clearances
Consider a location where the fireplace screen will not be exposed to direct sunlight from
A 15 ampere, 1 0 Volt, 60 Hz branch circuit with proper ground must be available at the
location. Preferably a dedicated branch cir
cuit should be provided to avoid circuit breakers
st to make sure the appliance operates properly by
plugging
Test all aspects of its operation (manual switches, remote and heater) to make sure all
ectronic devices, your new electric fireplace has been designed to operate at
). During the cold winter months, allow the
of odor during th first f w minut s of initial us
. This is
This appliance is for use on 1 0 Volts. The cord has a plug as shown in (A). An adapter as
blade grounding type plugs to two
-slot
he adapter must be connected to a
permanent ground such as a properly grounded outlet box. The adapter should not be used if a
To disconnect appliance, turn controls to off, then remove plug from outlet.
Plan where to locate and frame the fireplace. This will save time and money later when you
ing clearances
Consider a location where the fireplace screen will not be exposed to direct sunlight from
A 15 ampere, 1 0 Volt, 60 Hz branch circuit with proper ground must be available at the
cuit should be provided to avoid circuit breakers

7
CLASSIC SLIM -26
Description Built-in Appliance
Voltage 1 0V AC 60Hz
Watts 1500W Max
NO HEATER 15W
MOTOR HEATER 19W
Appliance Width 5 1/4” or 64.16 cm
Appliance Height 16 3/4 ” or 4 .58 cm
Appliance Depth 4 1/8” or 10.4 cm
Gross Weight 33.07 lbs or 15 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
5 1/ ”× 17“ or
64.77 cm× 43.18 cm
BTU 5118
This appliance has been tested in accordance
with the UL Standard 0 1 for fixed and location
dedicated electric room appliances in the United
States and Canada. If you need assistance
during installation, please contact your local
dealer.
NOTE: This applianc must b l ctrically
wir d and ground d in accordanc with local
cod s. In th abs nc of local cod s, us th
curr nt CSA C22.1 Canadian El ctrical Cod
in Canada or th ANSI/NFPA 70 National
El ctrical Cod in th Unit d Stat s.
251
4" [641.6mm]
271
8" [690mm]
163
4" [425.8mm]
171
4" [439.2mm]
45
8" [119mm]
41
8" [104mm]
251
8" [639.5mm]
135
8" [347mm]

8
CLASSIC SLIM -30
Description Built-in Appliance
Voltage 1 0V AC 60Hz
Watts 1500W Max
NO HEATER 16W
MOTOR HEATER 19W
Appliance Width 9 3/8” or 74.66 cm
Appliance Height 19 1/8 ” or 48.58 cm
Appliance Depth 4 1/8” or 10.4 cm
Gross Weight 39.68 lbs or 18 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
9 5/8”× 19 3/8“ or
75. 48 cm× 49. 13 cm
BTU 5118
This appliance has been tested in accordance
with the UL Standard 0 1 for fixed and location
dedicated electric room appliances in the United
States and Canada. If you need assistance
during installation, please contact your local
dealer.
NOTE: This applianc must b l ctrically
wir d and ground d in accordanc with local
cod s. In th abs nc of local cod s, us th
curr nt CSA C22.1 Canadian El ctrical Cod
in Canada or th ANSI/NFPA 70 National
El ctrical Cod in th Unit d Stat s.
311
4" [795mm]
195
8" [499.2mm]
293
8" [745mm]
16" [407mm]
191
8" [485.8mm]
45
8" [119mm]
41
8" [104mm]
29
3
8" [746.6mm]

9
CLASSIC SLIM -33
Description Built-in Appliance
Voltage 1 0V AC 60Hz
Watts 1500W Max
NO HEATER 17W
MOTOR HEATER 19W
Appliance Width 31 3/4” or 80.66 cm
Appliance Height 1/4 ” or 56.58 cm
Appliance Depth 4 1/8” or 10.4 cm
Gross Weight 47.39 lbs or 1.5 kgs
Plug Location Left side
Cord Length 70 7/8” or 180 cm
Rough Wall Opening
Size
3 ”× 1/ “ or
81. 8 cm× 57.15 cm
BTU 5118
This appliance has been tested in accordance
with the UL Standard 0 1 for fixed and location
dedicated electric room appliances in the United
States and Canada. If you need assistance
during installation, please contact your local
dealer.
NOTE: This applianc must b l ctrically
wir d and ground d in accordanc with local
cod s. In th abs nc of local cod s, us th
curr nt CSA C22.1 Canadian El ctrical Cod
in Canada or th ANSI/NFPA 70 National
El ctrical Cod in th Unit d Stat s.
221
4" [565.8mm]
45
8" [119mm]
41
8" [104mm]
335
8" [855mm]
223
4" [579.2mm]
31
3
4" [805mm]
191
8" [487mm]
313
4" [806.6mm]

INSTALLATION- BUILT-
IN
NOTE: Due to the many different materials used to build walls, it is highly recommended that
you consult your local builder before you install this appliance on a wall.
Pr paration
1. Select a location that is
not prone to moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
.
Mark the desired location on the floor and store the appliance in a safe, dry and dust free
place.
3. Prep
are a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
Prior to installing
, test the appliance to make sure the appliance is fully operational by
plugging the power supply cord into a 1 0 Volt grounded outlet.
The rough wall opening size of the fireplace:
W(“)
CLASSIC SLIM 26
5 1/
CLASSIC SLIM 30
9 5/8
CLASSIC SLIM 33
3
outlet of the heater which is fixed with magnetic stones.
10
IN
NOTE: Due to the many different materials used to build walls, it is highly recommended that
you consult your local builder before you install t
his appliance on a wall.
not prone to moisture and is located at least 0.91m or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
Mark the desired location on the floor and store the appliance in a safe, dry and dust free
are a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
, test the appliance to make sure the appliance is fully operational by
plugging the power supply cord into a 1 0 Volt grou
nded outlet.
The rough wall opening size of the fireplace:
D(“) H(“)
4 3/8 17
4 3/8 19 3/8
4 3/8 1/
steel bar at th gnetic stones.
NOTE: Due to the many different materials used to build walls, it is highly recommended that
you consult your local builder before you install this appliance on a wall.
not prone to moisture and is located at least 0.91m
or 3 feet away
from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.
Mark the desired location on the floor and store the appliance in a safe, dry and dust free
are a wall with a framed opening to accommodate the size of your unit. Leave at
least 1/4” (6mm) around the edge of the appliance. Any new wiring must be done in
compliance with local and national codes and other applicable regulations.
, test the appliance to make sure the appliance is fully operational by
steel bar at the outlet of the heater which is fixed with
INSTALLATION
1. Take off the steel bar at the outlet of the heater which is fixed with maagnetic stones.

. Unscrew the screws
to take off the front glass fixing steel bar.
3. Take off the fro
nt glass when the covering bar
to take off the front glass fixing steel bar.
nt glass when the covering bar
’s removed.
Screw
Front glass
11

4. Unscrew
screws on each side to take off the inner side bar.
5. Screw back the
inner side steel bar with long screws put in the manual bag.
(NOTE: You should leave gap for air circula
An air entrance slot is suggested. Or the fireplace will undergo overheat and get
damaged)
12
screws on each side to take off the inner side ba
r.
inner side steel bar with long screws put in the manual bag.
(NOTE: You should leave gap for air circula
tion when install the fireplace into a wall.
An air entrance slot is suggested. Or the fireplace will undergo overheat and get
inner side steel bar with long screws put in the manual bag.
tion when install the fireplace into a wall.
An air entrance slot is suggested. Or the fireplace will undergo overheat and get
Screw
Inner side bar
Air entrance slot

6. Screw back the front glass
panel
steel bar you
take off from STEP 1.
13
panel
after you finish
the media decoration
take off from STEP 1.
the media decoration
and put back the
Air entrance slot

14
HARD- WIRE INSTALLATION
Turn off the appliance completely and let cool before servicing. Only a qualified service
person should service and repair this electric appliance.
If it is necessary to hard-wire this appliance, a qualified electrician must remove the
cord connection, and wire the appliance directly to the house hold wiring.
This appliance must be electrically connected and grounded in accordance with local codes,
if hard-wired. In the absence of local codes, use the current CSA C .1 CANADIAN
ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL
CODE in the United States.
1. Remove the cover plate from the left side of the appliance by removing the two screws,
as shown below. Unscrew and remove power cord.
2. Cut off the copper head of the wiring and leave 1 cm (0.4 inch) uncovered wiring.

1
3. Connect the uncovered wiring with 14 A WG wiring (not provided with the appliance) y a wiring
connecting cap which you can find in the manual ag. Please make sure the live wire goes into
the “L”, the neutral wire into “N” and the ground wire into “G”.
4. Return the cover plate to the left side, adding a wiring protector which you can find in the
manual bag, and screw the two screws back in to fasten the plate.

MEDIA OPTIONS
T
he only media that comes with this a
optional decorative media if they choose. See dealer for more details.
DECORATIVE MEDIA INSTALLATION
Take off the steel bar at the outlet of the heater which is fixed with magnetic st
the screws
to take off the front glass fixing steel bar.
I
NSTALLING THE DECORATIVE MEDIA
Pour the fire glass media into the tray. Feel free to use any combination of the fire glas
media that you find most appealing. Put back the trim and front glass after you finish
installing the fire glass.
16
he only media that comes with this a
ppliance is ‘Clear glass
’. Consumers may purchase
optional decorative media if they choose. See deale
r for more details.
Clear glass
DECORATIVE MEDIA INSTALLATION
Take off the steel bar at the outlet of the heater which is fixed with magnetic st
to take off the front glass fixing steel bar.
NSTALLING THE DECORATIVE MEDIA
Pour the fire glass media into the tray. Feel free to use any combination of the fire glas
media that you find most appealing. Put back the trim and front glass after you finish
’. Consumers may purchase
Take off the steel bar at the outlet of the heater which is fixed with magnetic st
ones. Unscrew
Pour the fire glass media into the tray. Feel free to use any combination of the fire glas
s
media that you find most appealing. Put back the trim and front glass after you finish
STEP 1 STEP 2 STEP 3

17
OPERATION
Plug the fireplace into a 15 Amp wall socket.
MANUAL OPERATION
Plug the fireplace into a 15 Amp wall socket.
The fireplace can be operated either by the touch panel located on the left front top side of
the fireplace,
or by supplied remote control.
The fireplace can be operated either by the touch panel located on the left front top side of
or by supplied remote control.
The fireplace can be operated either by the touch panel located on the left front top side of
1. Press to turn on and off the fireplace.
2. Press to adjust the flame’s brightness. There are 7 brightness levels (L5 L4 - L3
L2 L1 L0 L6).The indicator light turns off automatically leaving it not operated within
10 seconds.
3. Press to adjust the ember bed brightness. There are 12 brightness levels (D4 D5
D6 D7 D8 D9 DA DB D0 D1 D2 D3).
4. Press to set the turn-off time, 30min-1h-2h-3h-4h-5h-6h-7h-8h-t0. The indicator light
turns off automatically leaving it not operated within 10 seconds. The timing turns off
when is pressed.
5. Press to turn on and off the heater in its AUTO mode. The setting temperature
switch through 59℉- 61℉- 63℉- 64℉- 66℉- 68℉- 70℉- 72℉- 73℉- 75℉- 77℉- 79℉-
81℉- 83℉ - ℉ in Fahrenheit or 15℃ -16℃ -17℃ - 18℃ - 19℃ - 20℃ - 21℃ - 22℃ - 23℃
- 24℃ - 25℃ - 26℃ - 27℃ - 28℃ - ℃ in Celsius. The temperature setting mode will be
closed automatically if leaving not operated for 5 seconds.
6. When the heater is on, press the for 5 seconds to switch between Celsius and
Fahrenheit.

18
REMOTE CONTROL OPERATION
For remote to function make sure the fireplace is plugged in and the remote has batteries.
Important: When operating the remote make sure you point the remote to the center of the
fireplace. Each time you press the button, the buzzer inside the unit will beep once. It takes
some time for the receiver to respond to the transmitter. Do not PRESS the buttons more
than once within two seconds for correct operation.
Set the current time of the remote control
Press the to activate the remote control and press to set the time and date.
When one of the “Sun” “Mon” “ Tue” “Wed” “Thu” “Fri” “Sat” is flashing, press or to
set the day of the week, press to confirm day of the week and then enter hour setting.
Press or to set the hour, press to confirm the hour and then enter minute
setting. Press or to set the minute and press to confirm the minute and
finish time setting.
Press this Power button to turn on and off the fireplace.
Press this Timer button to set the time to turn off the fireplace.
The available settings range from 3 minutes to 8 hours. As
shown in the following: :3 - 1: - 1:3 - 2: - 2:3 - 3: -
3:3 - 4: - 4:3 - 5: - 5:3 - 6: - 6:3 - 7: - 7:3 - 8: .
Once you have set the timer, the icon will be displayed
on the LCD screen of the remote control. Press this button
again to cancel the timer setting and the icon disappears.
Press the HEATER button once, one setting of heater works,
75 W, indicating “H 1” on display; Press again, two settings of
heater work, 15 W, indicating “H 2” on display; Press for the

19
third time to turn on the AUTO mode, press or to set the temperature
and or to switch temperature unit between Celsius and Fahrenheit.
Press this button to adjust the speed of the flame. There are 3 options: High-
Medium- Low.
Press this button to turn on and off the ember bed light. When in ON position, the
display screen of the remote control shows AD 1, when the number “1” flashes, you
can set the color of the ember bed by or . There are 1 different ember bed
light colors (AD1-1 ). When in AD 11 status, the color of the ember bed light cycles
through 1 colors. Press “SET” to confirm the setting.
Press the Flame button to turn on and off the Flame. When in ON position, the LCD
screen of the remote control shows 6 6 6. Press or or to change
the brightness of each color flame.
7 Day Timer Function
Press once, 7 days from Monday to Sunday will display on the LCD screen of
the remote control, press within 5 seconds to enter 7 day timer function. When
“Sun” flashes, press or to select the day that you want to set, press to
confirm your setting. Then “ON” will be display on the LCD screen of the remote
control, at the same time, digital of time hour flashes, press or to set the
time to turn the fireplace on. After setting the startup time, “OFF” will be displayed on
the LCD screen and press or to set the shutdown time. When the
shutdown time’s set, “AUTO” will be displayed on the LCD screen of the remote
control and the digital of temperature flashes. At this time, you can set the
temperature by or , or press to choose low heat (H1) or high heat
(H2). Now, you have finished setting of this function.

When the 7 day timer’s set, the icon will be displayed on the LCD screen of the
remote control. Press again to cancel the 7 da
will disappears.
NOTE: If the 7 day timing and the general timing are set at the same time, the
system will respond to an earlier shutdown time.
Press Refer button to check the settings of 7 day timer. Press or to see the
settings of the day of the week and or the settings of the startup and
shutdown time.
20
y timer and the icon