Remington AIR3D D7777XAU User manual

3 YEAR WARRANTY D7777XAU
AIR3D®STYLING GIFT SET
USE & CARE
MANUAL
PLEASE READ
PRIOR TO USE
To register your product go to
www.remington-products.com.au
www.remington.co.nz

2
IMPORTANT SAFEGUARDS
Warning: When the appliances are used in a bathroom, unplug
it after use since the proximity of water presents a hazard even
when the appliances are switched off.
When using electrical appliances, especially when children are
present, basic safety precautions should always be followed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING
KEEP AWAY FROM WATER
DANGER – As with most electrical appliances, electrical parts are
electrically live even when the switch is off.
To reduce the risk of death by electric shock:
• Always unplug it immediately after using.
• Do not place or store an appliance where it can fall or be pulled into a
bath or sink.
• Do not use while bathing.
• Do not place or drop into water or other liquid.
• If an appliance falls into water, “unplug it” immediately.
Do not reach into the water.
For additional protection, the installation of a residual current device (RCD)
with a rated residual operating current not exceeding 30mA is advisable in
the electrical circuit supplying the bathroom. Ask your electrical contractor
for advice.
WARNING – TO REDUCE THE RISK OF BURNS, ELECTROCUTION, AND
FIRE, OR INJURY TO PERSONS.
• Do not use the straightener on wet hair.
• An appliance should never be left unattended when plugged in to a
power outlet.
• These appliances are not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or lack
of experience and knowledge, unless they have been given supervision
or instruction concerning use of the appliances by a person responsible
for their safety. Keep the appliances and the power cords away from
the edge of table or countertops and out of reach of children and
persons with reduced physical, sensory or mental capabilities.

3
• These appliances are not toys. Children shall be supervised to ensure
they do not play with the appliances.
• Use these appliances only for their intended uses as described in this
manual. Do not use attachments not recommended by Remington.
• Do not operate this appliance with a damaged cord/plug or after the
appliance has malfunctioned, or been dropped or damaged in any
manner.
• There are no user serviceable parts. If power cord is damaged, it must
be replaced by the manufacturer or similarly qualified person in order
to avoid a hazard.
• Do not use on people who are sleeping.
• Never drop or insert any object into any opening of these appliances.
• Do not use outdoors or where aerosol (spray) products are being used
or where oxygen is being administered.
• When using the hair dryer, do not direct hot air towards the eyes or
other heat sensitive areas.
• Attachments, where provided, may be hot during and after use. Allow
them to cool before handling.
• When using the hair dryer, keep your hair away from the air inlet grille.
Do not let your hair get drawn into it.
• During the use of the straightener, the plates will be very hot. Do not let
bare skin touch heated surfaces.
• Do not place the heated straightener on any soft surface such as
a bed, carpet or a towel. Place only on a hard, flat, heat resistant
surface.
• Please check the voltage ratings on the product prior to use to ensure
it matches the voltage of the local area.
SAVE THESE INSTRUCTIONS

4
D7777XAU AIR3D®STYLING GIFT SET
HAIR DRYER & STRAIGHTENER
Thank you for purchasing your new Remington®AIR3D®Styling Gift Set.
Our AIR3D®hair dryer features the unique 3D airflow and Smooth
Conditioning Technology. The styling gift set also comes with a special
straightener with suspension plates coated with Advanced Ceramic for a
smooth glide and shiny-looking hair.
HAIR DRYER USE & CARE INSTRUCTION
4
6
3
1
7
8
9
2
5
KEY PARTS
1. Ceramic back-lit grille
2. Air inlet grille
3. Cool shot
4. Heat settings ( )
5. Speed settings ( )
6. Hang loop
7. 7mm ultra slim concentrator
8. 11mm fast drying
concentrator
9. Diffuser
10.Storage pouch (not shown)

5
BASIC HAIR CARE INSTRUCTIONS
For optimal results, shampoo and condition your hair prior to styling and
towel dry to remove excess moisture.
Note: This hair dryer is not suitable for use on synthetic wigs or hair
extensions.
UNIQUE 3D AIRFLOW TECHNOLOGY
The AIR3D®Hair Dryer features a unique design with 3D Airflow Technology
to deliver precise, evenly heated airflow for optimal styling performance.
SMOOTH CONDITIONING TECHNOLOGY
Besides the ionic generator, this hair dryer is infused with micro-
conditioners to eliminate static hair, smooth down the hair cuticles for
intensified softness, achieving the ultra-smooth finish.
LIGHTWEIGHT & BALANCED
With the motor located vertically in the handle, this hair dryer allows
optimised weight distribution to provide maximum comfort and control.
FITTING ATTACHMENTS
1. Push the desired attachment onto the front of your hair dryer.
2. Concentrator can be rotated as required.
HOW TO USE YOUR REMINGTON®AIR3D®HAIR DRYER
1. Plug the hair dryer into a 220-240V wall power outlet.
Note: Please note this hair dryer is only suitable for use on 220-240V
wall power outlets.
2. Switch the hair dryer on and select the desired speed setting (1 Low
or 2 High) using the speed setting switch ( ). The number below the
switch will light up to show you which setting you have selected. The
back-lit grille will light up white when you switch the hair dryer on.
3. Select the desired heat setting (1 Low, 2 Medium or 3 High) using the
heat setting switch ( ). The number above the switch will light up and
show you which setting you have selected.
4. Press and hold the cool shot button to direct cool air onto your hair to
help set your style. The back-lit grille will illuminate blue when you use
the cool shot feature.
5. After use, turn your hair dryer off and unplug it.
6. Let your hair dryer cool down before cleaning or storing away.

6
QUICK DRYING
Select the high heat and high speed setting and roughly dry your hair. Use a
brush or your hand to shake out excess moisture whilst drying and keep the
hair dryer in constant motion.
STRAIGHTENING
Select the high heat and high speed setting and roughly dry the hair. When
the hair is nearly dry, attach the concentrator nozzle (which minimises frizz)
and reduce the heat & speed. Section the hair according to thickness and
begin with straightening bottom layers first. Using your brush, follow the
concentrator from above, while slowly gliding down each section of hair
from roots to tips. Once bottom layers have been straightened, then
straighten the mid section and complete by straightening top layers.
NATURAL WAVY TEXTURE
Using the low heat and low speed setting, ‘scrunch’ sections of hair with
your fingers into the palm of your hand while directing airflow through your
fingers. Once you have reached the desired effect, use the cool shot on
each section of hair to hold style. For more volume lean forward and dry
hair in the upside down position.
LIFT & VOLUME
Use the hair dryer on the low heat and low speed setting, work from the
roots of hair and begin at the back of the head. Section your hair and use
a round brush to dry against the natural growth pattern of your hair. This
creates lift at the roots, which creates a style with volume.
STYLING
Set the hair dryer to the low heat and low speed setting and attach the
concentrator nozzle for precision drying. Section the hair and style using a
round brush. Concentrate the airflow directly on the hair while styling in the
direction you desire. If necessary, hold the airflow for 2-5 seconds on each
section while curling under or over for additional hold.
USING THE DIFFUSER
This hair dryer comes with a professional style diffuser. This diffuser dries
hair fast without blowing out the style. Perfect for naturally curly, wavy,
permed and fine hair or to give your hair a boost for volume.
NOTE: Always select the lowest heat setting when using the diffuser, as
damage may occur to the diffuser if higher heat settings are used.

DRY YOUR HAIR USING THE DIFFUSER
Dry your hair beginning at the roots and using the circular motions, always
moving in the same direction. Use the diffuser with the hair dryer set at the
low heat and low speed setting. Continue drying, keeping the hair dryer at
a 90-degree angle to the scalp. This will lift the roots away from the scalp
giving your hair volume. Finish by drying the ends.
ADD VOLUME TO YOUR HAIR USING THE DIFFUSER
To add volume to your hair, tilt your head upside down and dry so that the
roots fall away from your scalp. Use the diffuser with the hair dryer set at
the low heat and low speed setting. Point the hair dryer at the roots to give
your hair maximum volume. Continue the process to the ends of your hair.
Important Note: Remington AIR3D® hair dryer is constructed differently
from other Remington hairdryers. When drying your hair, at all times please
avoid your hair covering the back of the dryer to prevent it from being
caught in the grille.
CLEANING AND MAINTENANCE
To maintain peak product performance and to prolong motor life, it is
important to regularly clean the air inlet grille.
Unplug the hair dryer and allow it to cool.
Use a lint free cloth or soft brush to gently remove dust and debris from the
grille.
7

1
6
2
KEY PARTS
1. Advanced ceramic coated
plates
2. Indicator light
3. Suspension plates
4. On/off switch & Hinge lock
5. Salon swivel cord
6. Storage case
8
3
45
STRAIGHTENER USE & CARE INSTRUCTION

9
BASIC HAIR CARE INSTRUCTIONS
For optimal results, shampoo and condition your hair, then dry your hair
thoroughly and make sure that it is tangle free prior to straightening.
NOTE: The AIR3D®Styling Gift Set Straightener is not suitable for use on
synthetic wigs or hair extensions.
ADVANCED CERAMIC COATED PLATES
Advanced Ceramic is an exclusive layer of CeraSol Ceramic. Advanced
Ceramic Coated plates are proven to have 10x more ceramic* for superior
high even heat across the plates with no hot spots. Its 2x smoother*
creating an effortless glide during straightening for silky smooth results and
2x longer lasting* ensuring plate durability.
*vs. standard Remington straightener ceramic coating
HOW TO USE YOUR REMINGTON®AIR3D®STYLING GIFT SET
STRAIGHTENER
Before use, ensure the hair is clean, dry and tangle free. Section the hair
prior to styling and style the lower layers first.
Plug in to any household (120-240V AC) wall power outlet, and move the
on/off switch into the “I” position, this will unlock the plates and also switch
the straightener on. The on indicator light will begin to flash and continue to
flash until the straightener has heated up to 200°C. The straightener will be
ready to use in 30 seconds from switched on. Take extra care when using
the straightener, as it can get very hot. Ensure you test the straightener on
a small section of hair first.
To switch your straightener off, move the on/off switch into the “O” position
but not close the plates and only close the plates once they are fully cooled
down.
TO STRAIGHTEN YOUR HAIR
To make styling easier, part the hair either in the middle or to the side and
use clips to section your hair, top, sides and back.
You may need to comb through your hair before straightening to ensure that
it is tangle free.
Start at the nape of the neck and straighten the underneath sections of hair
first. When the underneath sections of hair are complete, move to the next
layers, finishing with the hair around the part line.
Take about a 5cm section of hair and pull taut and down and away from the

10
scalp. Holding the straightener with the other hand, start at the roots and
clamp the hair firmly between the plates.
Firmly holding the plates together, run the straightener down through the
entire length of the section of hair from roots to ends, in one smooth stroke.
Repeat until the desired amount of straightening has been achieved.
TO CURL YOUR HAIR
Section your hair as above. Take about a 5cm section of hair and firmly grip
it between the plates, close to the roots. Note: The smaller the section the
tighter the curl.
Keeping tension firm, gently rotate the straightener 180° whilst pulling
through the length of the hair section. Make sure to keep rotating the
straightener. Remove straightener and holding the hair length, allow the
curl to spring into shape.
AUTOMATIC WORLDWIDE VOLTAGE
The AIR3D®Styling Gift Set Straightener features automatic voltage
adjustment for international use. Plug the unit into any domestic power
outlet and it will adjust automatically to the voltage being supplied.
NOTE: Some countries will require the use of a plug adaptor that is not
included with your straightener.
HINGE LOCK
Safely store your AIR3D®Styling Gift Set Straightener with the plates
locked together.
To unlock, slide the hinge lock into the “I” position. To lock, slide the hinge
lock into the “O” position
NOTE: Do not heat the straightener in the locked position. Ensure the plates
are fully cooled down before put away your straightener.
MAINTENANCE
This straightener is designed for household use and is virtually maintenance
free. If cleaning becomes necessary, disconnect the straightener from the
power outlet, allow it to cool, then wipe the exterior surface and the plates
with a soft damp cloth.
Do not immerse the unit in any liquid. Do not use an abrasive cleaning
fluid or material to clean the plates as this will scratch the surface and
deteriorate the effectiveness of the surface.