Renesas Emulator MCU Board M37549T-RLSS User manual

M37549T-RLSS
Emulator MCU Board for 7548/7549 Group
User’s Manual
CAUTION If the requirements shown in the "CAUTION" sentences are ignored,
the equipment may cause personal injury or damage to the products.
Renesas Tools Homepage http://www.renesas.com/tools
Rev.1.00
Jul. 10, 2007
REJ10J1444-0100 (1/4)

1. Outline
The M37549T-RLSS is an emulator MCU board for the 7548/7549 Group.
2. Package Components
(1) M37549T-RLSS 1 pc.
(2) M37549T-RLSS User's Manual (This manual) 1 pc.
(3) M37549T-RLSS User's Manual (Japanese) 1 pc.
3. Specifications
Table 1Specifications
Emulator M38000T2-CPE *
Operating mode Single-chip mode
Maximum operating
frequency
Vcc = 4.5 to 5.0 V: 8.0 MHz (frequency/2mode)
Vcc = 2.4 to 5.0 V: 2.0 MHz (frequency/2mode)
Vcc = 2.2 to 5.0 V: 1.0 MHz (frequency/2mode)
Vcc = 4.0 to 5.0 V: 8.0 MHz (High-speed mode)
Vcc = 2.4 to 5.0 V: 4.0 MHz (High-speed mode)
Vcc = 1.8 to 5.0 V: 1.0 MHz (High-speed mode)
Operating power
voltage 1.8 to 5.5 V
* A combination of the PC4701 and M38000TL2-FPD is not supported.
4. External Dimensions
VCCGNDRESET +
64.0
45.0
R1
4.2
11.0
15.24
Figure 1 External dimensions
(2/4)

(3/4)
5. Connection Procedure to the user system
Connect the emulation probe to the connector on the upper panel of the M37549T-RLSS. Connect the M37549T-RLSS to the 42-pin
SDIP socket on the user system. Table 2 shows pin allocation of the M37549T-RLSS, and Figure 2 shows connector dimensions.
Table 2 CN1 connector pin allocation
Pin No Signal Pin No Signal
1 N.C 42 N.C
2 N.C 41 N.C
3 N.C 40 P13/AN3/KEY3
4 P14/AN4/KEY4 39 P12/AN2/CMP2
5 P15/AN5/KEY5 38 P11/AN1/CMP1
6 RESET 37 P10/AN0/CMP0
7 P16/AN6/KEY6 36 P31
8 P17/AN7/KEY7 35 P30
9 N.C 34 Reserved
10 N.C 33 Reserved
11 N.C 32 Reserved
12 P20/Xout/Xcout 31 Reserved
13 Vss 30 P07(LED7)/Srdy
14 P21/Xin/Xcin 29 P06(LED6)/Sclk
15 Vcc 28 P05(LED5)/TxD
16 CNVss 27 P04(LED4)/RxD
17 P00(LED0)/INT0 26 P03(LED3)/CAP0
18 P01(LED1)/INT1 25 P02(LED2)
19 N.C 24 N.C
20 N.C 23 N.C
21 Vss 22 N.C
* Do not connect signal to Reserved parts.
142
21 22
15.24
1.778
Figure 2 CN connector dimensions

(4/4)
6. Oscillator Circuit
This product has two oscillator circuit patterns for the main clock XIN and sub-clock XCIN. The oscillator circuit on the user system
may not work properly because the oscillator circuit pin of the emulator MCU is not close enough to the oscillator circuit of the user
system. In this case, mount the oscillator circuit on the oscillator circuit pattern of the M37549T-RLSS.
Figures 3, 4 and 5 show the M37549T-RLSS circuit pattern and diagram.
xin
xout
X1
X2b
C1
C2
R3
X2a
R2
JP2 JP3 JP2
X2
R3
C1 C2
JP3
RdX2
Figure 3 When a ceramic oscillator with built-in capacitor is used for Xin/Xout
xin
xout
X1
X2b
C1
C2
R3
X2a
R2
JP2 JP3 JP2
X2
R3
C1 C2
JP3
Rd
X2
Capacitor
Figure 4 When a ceramic oscillator without built-in capacitor is used for Xin/Xout
xin
xout
X1
X2b
C1
C2
R3
X2a
R2
JP2 JP3 JP2
X1
R2
R3
C1 C2
JP3
Rd
X2
Rf Capacitor
Figure 5 When Xcin/Xcout is used as a circuit
7. Precautions
IMPORTANT
Notes on This Product:
zWe cannot accept any request for repair.
zWhen using the oscillator circuit on the M37549T-RLSS, check output waveform of pin Xout and pin Xcout with an
oscilloscope.
zWhen mounting an oscillator circuit on the M37549T-RLSS, make sure not to short-circuit the user system.
zFor inquiries about the product or the contents of this manual, contact your local distributor.
Renesas Tools Homepage http://www.renesas.com/tools